Crane Payment Innovations 5IN1 5 in 1 Credit Card Bezel User Manual manual

MEI 5 in 1 Credit Card Bezel manual

manual

Bezel Cable Bezel Cable A A General Information The 5 in 1 bezel kit has been designed to add a credit card reader to a Series 2700 bill validator. The 5 in 1 bezel replaces the compact bezel. Remove the bill validator from the vending machine. To remove the compact bezel from the validator: 1. Remove four phillips screws (A) located on the front of the bezel. Slide the PCB cover ¼ inch towards the top of the validator and lift it off. Remove the old bezel and mounting plate. 5 in 1 bezel installation 2. Place the 5 in 1 bezel on the bill validator and tighten the three screws. Plug the ribbon cable (blue side up) into the locking socket on the validator control board. Be careful not to pinch or damage the bezel cables when installing the 5 in 1 bezel. 3. Re-install the PCB cover. Remount the bill validator in the vending machine. 4. Plug the 5 in 1 bezel cable into the Advance 5000 Bezel Socket. 5 in 1 Notes: FCC ID: QP85IN1 CANADA - IC: 1297A-MEI5IN1 CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (a) This device may not cause harmful interference, and (b) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Contact MEI Technical Support @ 1-800-345-8172 with any questions. MEI 1301 Wilson Drive West Chester, Pa. 19380 ©2012 MEI Inc. Part # XXXXXXXXX www.meigroup.com General Information The 5 in 1 bezel kit has been designed to add a credit card reader to a Series 2700 bill validator. The 5 in 1 bezel replaces the compact bezel. Remove the bill validator from the vending machine. To remove the compact bezel from the validator: 1. Remove four phillips screws (A) located on the front of the bezel. Slide the PCB cover ¼ inch towards the top of the validator and lift it off. Remove the old bezel and mounting plate. 5 in 1 bezel installation 2. Place the 5 in 1 bezel on the bill validator and tighten the three screws. Plug the ribbon cable (blue side up) into the locking socket on the validator control board. Be careful not to pinch or damage the bezel cables when installing the 5 in 1 bezel. 3. Re-install the PCB cover. Remount the bill validator in the vending machine. 4. Plug the 5 in 1 bezel cable into the Advance 5000 Bezel Socket. 5 in 1 Notes: FCC ID: QP85IN1 CANADA - IC: 1297A-MEI5IN1 CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (a) This device may not cause harmful interference, and (b) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Contact MEI Technical Support @ 1-800-345-8172 with any questions. MEI 1301 Wilson Drive West Chester, Pa. 19380 ©2012 MEI Inc. Part # XXXXXXXXX www.meigroup.com VN2700 series Bill Validator, 5 in 1 Bezel Kit Installation Guide VN2700 series Bill Validator, 5 in 1 Bezel Kit Installation Guide Locking collar Locking collar

Navigation menu