Crane Payment Innovations ECHOICE eChoice RFID Reader User Manual
Crane Payment Innovations eChoice RFID Reader
User Manual
4. Place the new mounting plate and the eChoice Bezel on the note validator, and tighten the screws. The ground wire should be connected to the mounting plate under bezel and out of view. eChoice Bezel Kit 5. Be careful not to pinch or damage the bezel cable when installing the eChoice Bezel. Installation Guide General Information The eChoice Bezel Kit has been designed to add a cashless payment system to a Series 2600 or Series 2700 MEI note validator. These note validators connect to the vending machine using the MDB interface. The eChoice Bezel replaces a VFM bezel. 1. Turn OFF power. 2. Unplug the Validator’s MDB cable from vending machine chain. 3. Remove the note validator from the vending machine. (Four (4) - 11/32” nuts hold the validator in the machine). 6. Re-install the PCB cover. To remove the old bezel from the validator: 1. Remove the three or four phillips screws (A) located on the front of the bezel. 2. Slide the PCB cover ¼ inch towards the top of the validator and lift it off. 3. Remove the old bezel and mounting plate. If you are removing a High Visibility or 3 in 1 Bezel, carefully disconnect the ribbon cable from the validator circuit board before lifting the old bezel off. 7. Remount the note validator in the vending machine. (Four (4) - 11/32” nuts hold the validator in the machine). 8. Plug in the MDB cable from the Validator into the Vending machine MDB chain. 9. Plug the eChoice Bezel cable into the Advance 5000 Bezel Socket. Series 2700 Bezel Cable See the Advance 5000 manual for installation instructions. Latch – Pull down with your finger nail or screw driver. FCC ID: QP8ECHOICE CANADA - IC: 1297A-ECHOICE CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (a) This device may not cause harmful interference, and (b) this device must accept any interference received, including interference that may cause undesired operation. For Series 2600 Series 2700 Note Validators Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. eChoice Bezel Contact MEI Technical Support @ 1-800-345-8172 with any questions. CPI 3222 Phoenixville Pike, Suite 200, Malvern, Pa. 19355 Cash • Coupons • Magnetic Stripe Cards Contact (EMV) Cards • Contactless Cards ©2016 CPI. Part # XXXXXXXXX www.cranepi.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Annotate, Fill forms, Extract, Print high-res Author : KarenS Create Date : 2016:03:01 23:46:57-07:00 Modify Date : 2016:03:08 17:05:11-07:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2016:03:08 17:05:11-07:00 Format : application/pdf Title : Microsoft Word - 9_eChoice Bezel Installtion Guide_Note Validator.docx Creator : KarenS Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:cc43c2d8-54cc-4d31-8170-8fd8308b87ee Instance ID : uuid:db74f195-ee2e-4c2f-858b-609bbe201539 Page Count : 2EXIF Metadata provided by EXIF.tools