Creative Industry PC-68A Oximeter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2860555
Application ID	TzxkHg7QeNCQ1Eehlg8Esg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.74kB (259205 bits)
Date Submitted	2015-12-30 00:00:00
Date Available	2015-12-30 00:00:00
Creation Date	2015-11-13 10:57:58
Producing Software	PDFdo.com 5.5.6.0
Document Lastmod	2015-11-13 10:57:58
Document Title	User Manual

Pulse Oximeter
Directions for Use
Intended Use
This oximeter is intended to be used
with Baby Monitor, and it is an
additional or optional accessory to
measure the functional arterial oxygen
saturation (SpO2) and pulse rate (PR)
for infant or baby in the way of
non-invasive and long term monitoring.
Contraindications
This oximeter including its sensor is
contraindicated for use on the baby with
excessive movement or for prolonged
use at the same measuring site.
seat fully into the hole in the back of the probe
holder.
2) Bind the oximeter on the leg near ankle with
its belts and position the front panel to a
proper place for convenient operation, as
shown in Figure 4.
3) Wrap up the Y-type sensor onto the baby’s
sole by the rubber wrapper, as illustrated in
Figure 3. Make sure the alignment of the
light-emitting tip (LED) and the photodetecting tip (PD) for aiming at each other,
then thread the end of wrap belt through the
outside slots on the probe holders and tighten
the rubber belt with proper force. The final
placement is shown in Figure 4.
Instructions for Connection
1) Insert the sensor tips into the slots on the
probe holders. Place the sensor tip labeled
“LED” into the stationary probe holder on
the silicone wrap belt, and place the sensor
tip labeled “PD” into the sliding probe holder,
as illustrated in Figure 1 and Figure 2.
Figure 3 Sensor wrapping up
Y-type
SpO2
Sensor
with
Rubber
Wrapper
Pulse Oximeter
Figure 4 Placement of the Oximeter and the Sensor
Figure 1 Probe tip and holder
NOTE: The sensor connection is critical for
the signal strength and quality. Try to make
LED and PD facing each other in opposite side,
so that the light beam is as vertically
transmitted as possible and the light path is as
short as possible.
Figure 2 Y-type SpO2 Sensor with Rubber Wrap
NOTE: Make sure that the silicone button
Instructions for Operation
Caution: ① Do not sterilize by irradiation,
steam, or ethylene oxide. ②Make sure the
After all connection completed, press the Power
Button ( ) for 3 seconds to power on the
oximeter, referring to Figure 5. When the
oximeter is powered up, the Power Indicator
(yellow lamp ) will light constantly. If the heart
beat is detected, the Heartbeat Indicator (red
lamp ) flashes according with the heart rate. At
the same time the oximeter sends the measured
data (SpO2 and PR) to Baby Monitor in a given
time interval via wireless communication, and
the SpO2 and PR value will be displayed on the
terminal side of Baby Monitor.
Figure 5 Appearance of the Pulse Oximeter
NOTE: ①The oximeter has not automatic
power-off function. Press the Power Button for
3 seconds to turn it off after the end of use
sensor is dry and clean before use.
Warranty
Our company offers a 12-month warranty
against manufacturing defects for this product in
its undamaged condition.
FCC Caution.
§15.19 Labelling requirements.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
§15.21 Information to user.
Any Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment.
each time.②If the Power Indicator flashes,
that means the battery voltage is low for the
oximeter, please replace the batteries.

Cleaning and Disinfection
It is recommended to clean the oximeter
including its sensor with 75% Alcohol wipes or
70% Ispropanol (Isopropyl) before use.
§15.105 Information to the user.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable
protection
against
harmful
interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
Shenzhen Creative Industry Co.,Ltd.
Tel:+86-755-2643 3514
2/F,Block 3,Nanyou Tian’an Industry Town,
Fax: Tel:+86-755-2643 2832
Shenzhen, GD 518054, P.R. China
E-mail:market@creative-sz.com
Sep. 5, 2014
V1.0
Pulse Oximeter
Directions for Use
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the
equipment and receiver.
-Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
* RF warning for Portable device:
The device has been evaluated to meet general
RF exposure requirement. The device can be u
sed in portable
exposure condition without restriction.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Producer                        : PDFdo.com  5.5.6.0
Create Date                     : 2015:11:13 10:57:58+08:00
Modify Date                     : 2015:11:13 10:57:58+08:00

EXIF Metadata provided by EXIF.tools