Cree RFM RFM MODULE User Manual C RF Module

Cree, Inc RFM MODULE C RF Module

Contents

User Manual_C.-RF Module

INSTALLATION INSTRUCTIONS
CM-CWC-1
Cree SmartCast™ Technology Wireless Control Module Replacement Kit
Includes: CR Series and CS Series
LPN00243X0001A0_C
1 of 2
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Before installing turn off the power at the circuit breaker.
2. Any changes or modications to these devices not explicitly approved by
manufacturer could void your authority to operate this equipment.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
1
2Cree Logo
Cree Logo
STEP 1:
Turn power off and remove old control module
from luminaire by pressing the clips located on
both sides of control module inward and pull
control module out from luminaire.
NOTE: For location of the control module
reference Figure 1 for CR luminaires and
Figure 2 for CS luminaires.
STEP 2:
Orient the new control module so that the
Cree logo is in the lower left corner. Attach the
new control module to the CR or CS luminaire
by pressing in on the clips located on the sides
of the control module and inserting it into the
designated connector.
STEP 3:
Turn power on. The new control module is
correctly installed if the Blue LED displays a 2
blink sequence.
NOTE: If the blue LED does not respond
with the two-blink sequence, please follow
the RESET instructions to return the control
module to factory defaults.
STEP 4:
On the Configuration Tool, select “Replace
Devices” from the “Advanced” menu and
follow the on-screen directions.. This will
remove old device(s) from the network and
add the new device(s).
RESET
NOTE: The Blue LED is located behind the
Cree logo on the control module. The Cree
logo with illuminate blue when the Blue LED is
active.
STEP 1:
Actuate RESET button through the test hole.
Push and hold (approximately 10 sec), LED on
control module will blink fast.
STEP 2:
Release for 1 sec.
STEP 3:
Press/Hold RESET button for 0.5 sec. Light
will go to full bright and the Blue LED on
the control module should be in a 2 blink
sequence.
TO INSTALL:
LPN00243X0001A0_C
2 of 2
www.cree.com/lighting
© 2014 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See
www.cree.com/lighting/products/warranty for warranty and specifications. Cree® and the Cree logo are
registered trademarks, and SmartCast™ is a trademark of Cree, Inc.
FCC NOTICE
To comply with the FCC RF exposure compliance requirements, this device and its antenna
must not be co-located or operating to conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 5cm between the
radiator & your body. No other antenna is authorized for use with this product.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved could void your authority to use
this equipment.
This device complies with Part 15 of the FCC Rules. Operation to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
This device has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the device is operated in a commercial
environment. This device generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this device in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.
The LED in the front of this device operates within Risk Group 1 levels per IEC 62471.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device. In addition, this device complies with ICES-003 of the Industry
Canada (IC) Regulations.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.

Navigation menu