Crestron Electronics TX3 Handheld Touchpanel User Manual Quickstart PTX3

Download:
Mirror Download [FCC.gov]
Document ID	1352438
Application ID	qZhigfFgMsFxmcDMKZURMA==
Document Description	Manual PTX3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	151.67kB (1895839 bits)
Date Submitted	2010-09-30 00:00:00
Date Available	2010-10-01 00:00:00
Creation Date	2010-03-18 20:57:14
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2010-03-18 18:13:35
Document Title	Quickstart: PTX3
Document Creator	Adobe Illustrator(R) 11
Document Author:	Crestron Electronics, Inc.

PTX3
quickstart guide
Prodigy® Handheld Touchpanel
Introduction
The Prodigy® PTX3 is a versatile yet cost effective home
theater remote control. This state of the art handheld
two-way controller includes a 2.8” active matrix
touchscreen capable of displaying stunning graphics and
dynamic text with true feedback.
The ergonomic layout of pushbuttons provides intuitive,
tactile control for hands and fingers of all sizes. Its
compact size and design offer easy one handed
operation, while its 802.15.4 wireless technology affords
reliable communications over everything from home
theater to whole house automation as part of a complete
Prodigy system.
Application
The following diagram illustrates a PTX3 in a system with
other Prodigy devices.
Power
A. Install the Battery
Configure the Touchpanel
The setup screen is the starting point for
configuring the PTX3. When power is applied
for the first time, the screen shown below
appears.
Perform the following procedure to install the battery
pack in a PTX3 touchpanel:
1. Place the touchpanel screen side down on a
clean, soft surface.
Touch the screen to display the PTX3 setup
screen, as shown in the illustration below.
The setup screen enables basic configuration
procedures prior to regular operation of the
touchpanel.
2. Remove the battery compartment cover on the
rear of the touchpanel.
3. Carefully connect the multi-pin connector of the
battery with the corresponding connector inside
the battery compartment. The pin side of the
connector should be facing upward (toward the
rear of the touchpanel). Red wires should be
above black wires (toward the top of the
touchpanel). Ensure the connector is fully
seated.
4. Place the battery in
the compartment,
oriented so the wires
for the multi-pin
connector are on the
bottom, as shown
in the illustration to
the right.
5. Re-attach the battery
compartment cover.
NOTE: During regular operation
of the touchpanel, to activate the
setup functions, press hard keys
1, 2, 3, and 4 in sequence twice
(i.e. press 1, 2, 3, 4, 1, 2, 3, 4)
within a five second period.
B. Charge the Battery
To charge the battery pack, the PTX3 must be
placed on the included PTX3-DS docking
station/charger. Connect the included power pack
to the PTX3-DS.
PTX3
NOTE: Before using the PTX3 for the first time,
charge its battery for a least two hours by placing
it on the PTX3-DS docking station/charger. The
green LED on the front of the PTX3 will blink while
the battery is charging.
NOTE: When not using the PTX3, store the unit
on its docking station/charger.
USB Port Location
For Regulatory Compliance information, refer to the latest
version of Doc. 7002.
QUICKSTART DOC. 7001A (2027729)
03.10
www.crestron.com/prodigy
©2010 Specifications subject to
change without notice.
888.273.7876
201.767.3400
All brand names, product names, and trademarks
are the property of their respective owners.
NOTE: USB port for loading projects
and upgrading firmware, is located
behind the battery compartment
cover on the rear of the unit.
PTX3
quickstart guide
Prodigy® Handheld Touchpanel
Acquire the PTX3
Use the Prodigy Composer software (available for download from www.crestron.com/prodigycomposer) to configure your Prodigy system. A Prodigy
Network Setup Wizard is included with Prodigy Composer. Before a PTX3 can be used, it must first be acquired by a PMC2 that is connected to a
Prodigy system. To acquire the PTX3, perform the following when prompted by the Prodigy Network Setup Wizard.
1. Put the PMC2 in Acquire mode by pressing its ACQUIRE button (or follow the prompts in the Network Setup Wizard to do this automatically).
2. Put the PTX3 in Acquire mode by doing the following:
a. On the main setup screen shown on page 1, touch RF Setup to go to the “RF Setup” screen, shown in illustration
Troubleshooting
The following table provides corrective action for possible trouble
situations. If further assistance is required, please contact a Crestron
customer service representative.
TROUBLE
below.
PTX3 does not
function.
b. Touch Acquire Gateway.
c.
Problem Solving
The “Confirm Acquire” screen, shown in illustration
process.
below, will be displayed.
3. When the acquire is complete, the “RF Setup” screen will show the gateway’s EUID, the channel number and RF ID, as shown in illustration 4
below. Take the PMC2 out of the Acquire mode by pressing its ACQUIRE button (or follow the prompts in the Network Setup Wizard to do this
automatically).
“RF Setup” Screen
CORRECTIVE ACTION
Battery was not charged
or is discharged.
Place the PTX3 on its
docking station/charger and
charge the battery. (Refer to
Section 3 B “Charge the
Battery”.)
Battery connector is not
fully seated.
Verify battery is properly
connected.
Power pack connector is
not fully seated in docking
station.
Verify power pack is properly
connected.
PTX3 is off or in standby
mode or has no power.
Verify the PTX3 has power
and is on.
PTX3 is out of range or
has poor access to PMC2.
Move back within range of the
PMC2 or other Prodigy
wireless network devices.
PTX3 RF ID does not
match ID in the program.
Change the RF ID or rerun the
Network Setup Wizard.
below, will be displayed. Touch YES, Acquire New Gateway to begin the
d. The “RF Gateway Acquisition In Progress” screen, shown in illustration
POSSIBLE CAUSE(S)
“Confirm Acquire” Screen
“RF Gateway Acquisition
In Progress” Screen
PTX3 shows
unexpected or
intermittent
feedback and/or
does not control
any devices.
“RF Setup” Screen
(After Acquire)
Further Inquiries
If you cannot locate specific information or have questions after
reviewing this guide, please take advantage of Crestron's award
winning customer service team by calling Crestron at
1-888-CRESTRON [1-888-273-7876].
You can also log onto the online help section of the Crestron website
(www.crestron.com/onlinehelp) to ask questions about Crestron
products. First-time users will need to establish a user account to fully
benefit from all available features.
As Crestron improves functions, adds new features and extends the
capabilities of the PTX3, additional information may be made available
as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical
documentation revision.
Load the Project
Use the Prodigy Composer software (available for download from www.crestron.com/prodigycomposer) to configure your Prodigy system.
Refer to the help file for instructions on loading the project.
NOTE: To prevent the panel from going to sleep during project uploads, place the PTX3 on its docking station.
For Regulatory Compliance information, refer to the latest
version of Doc. 7002.
QUICKSTART DOC. 7001A (2027729)
03.10
www.crestron.com/prodigy
©2010 Specifications subject to
change without notice.
Check the Crestron website periodically for manual update availability
and its relevance. Updates are identified as an “Addendum” in the
Download column.
888.273.7876
201.767.3400
All brand names, product names, and trademarks
are the property of their respective owners.
PTX3
Future Updates

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Print high-res
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Create Date                     : 2010:03:18 20:57:14Z
Modify Date                     : 2010:03:18 18:13:35-04:00
Metadata Date                   : 2010:03:18 18:13:35-04:00
Creator Tool                    : Adobe Illustrator(R) 11
Format                          : application/pdf
Creator                         : Crestron Electronics, Inc.
Title                           : Quickstart: PTX3
Description                     : Prodigy® Handheld Touchpanel
Document ID                     : uuid:111b0a2d-fb90-4592-8203-ccb34d004fdb
Instance ID                     : uuid:9f44f3b5-01c3-4e39-b149-0c9eaf403fb8
Page Count                      : 2
Page Layout                     : SinglePage
Subject                         : Prodigy® Handheld Touchpanel
Author                          : Crestron Electronics, Inc.
Keywords                        : Prodigy, Handheld, Touchpanel, PTX3

EXIF Metadata provided by EXIF.tools