Cyber Acoustics P560 5.1 Speaker System User Manual P560 Manual N

Cyber Acoustics (HK) Ltd. 5.1 Speaker System P560 Manual N

Users Manual

      P560    Owner’s Guide   5.1      Speaker System
1
2
3
4
5Thank you for purchasing Rockford Fosgate P560 5.1 Powered Speaker System. We hope it exceeds your expectations in sound quality. The P560 is designed to deliver superior sound with 5.1 theater quality sound for your movies, games, and music. We offer various methods of connectivity including Bluetooth, Optical, RCA, AUX, and the latest in gaming sound cards. So whatever audio player you have (i.e. mobile phone, gaming console, tablet, computer, TV, etc.), the P560 will be your go to system.   Dolby Digital is the universal standard for 5.1 digital sound. Onboard 5.1 digital decoding enables detailed surround sound—from the roar of the crowd to the footsteps right behind you—in your Dolby Digital soundtracks.Dolby®  DigitalCAUTION•  Do not plug the power supply in until all connections are made.     eo ampliers, space heaters,  •  Keep speakers away from sources of extreme heat such as ster    stoves, heat vents, etc.•  Do not wipe any part of the system with cleaning solvents such as furniture wax, bleach,     benzene, acetone, or ammonia.      5 satellite speakers     1  Subwoofer2  Control console3  IR remote  12" aux cable45  3 x 3.5mm cables6  RCA cable 7  2 x AAA Batteries8  Owner’s guide with connection diagram91010      T-560   Owner’s Guide   5.1      Speaker System 8572364119Your system includes:  5 sets of connection wire (7.6m / 25ft x 2 ; 4.6m / 15ft x 3)
6Speaker PreparationFor speaker preparation, we suggest you arrange your system similar to the diagram shown below.   •  Front Satellite Speakers — Place the two front satellite speakers on opposite sides of your     TV or computer monitor. Locate them equal distance from each other and adjust the angle so     the speakers are facing you.•  Rear Satellite Speakers — Place the two rear satellite speakers behind you (with similar distance    apart as the front speakers). Then adjust the angle to face you.•  Center Satellite Speaker — Place the center satellite speaker above or below your TV or     computer monitor (Caution: do not put center satellite directly on top of TV or computer monitor).•  Subwoofer – You can put the subwoofer anywhere in your room. To get the strongest bass, put    your subwoofer near a wall, corner, or underneath a desk. Make sure that nothing is closer than    20cm to the driver or port tube because it will affect the sound. It is important to allow for     enough ventilation around the subwoofer, we recommend 20cm .•  Control Console – Place the console where it is easy to reach and make sure the IR receiver     window is not blocked.    SubwooferFLRL RRFRC
7Subwoofer back panel1.  Control Console connection port2.  Red/White (RCA)3.  Optical in (Digital input)4.  PC Sound card connections       5.  Satellite output connection ports6.  AC power cordLINE INOPTICAL INFL / FRRL / RRC / SWAC PowerCONSOLEFLFRRLRRC123456Speaker Connection
8Control Console1.      Input selection: Use this button to switch between your audio source. (Optical, Line in, PC         in, AUX in, Bluetooth)2.      Effect: Use this button to switch between 2.1 output or 5.1 output.3.      Bass: Press this button to adjust bass channel; when the BASS LED is on, you can adjust          bass volume by rotating the knob.4.      Power: Master power on/off5.      Mute: Mute the entire system6.      Volume / level adjustment knob: Adjust master volume7.      IR remote sensor8.      Input selection indicator9.      Speaker output indicator10.    Decode indicator: LED will be on when Dolby Digital signal is detected.11.    Sound effect indicator: Either 2.1 output mode or 5.1 output mode.12.    Bass indicator: When LED is on you can adjust bass level.13.    Headphone output jack14.    AUX input jackFront                              BackPOWER MUT EBASSEFFECTINPUTBLUETOOT HAUX I NLIN E INOPTICALFLFRCRLPC INRRSUBBASS2.13D1234 5678910121113 14DECODE
9IR Remote Control 1.      Input selection: Use this button to switch between your audio source.          (Optical, Line in, PC in, AUX in, Bluetooth)2.      Effect: Use this button to switch between 2.1 output or 5.1 output.3.      Play: During Bluetooth connection, press this button to play or pause. Press and hold for 5         seconds to enter Bluetooth pairing mode. 4.      Master volume: Up/Down5.      Mute the entire system6.      Master Power: On/OffPower On•       Plug the subwoofer power cable into an electrical outlet.•       Press Power on the Control Console to power on the speaker system.Caution: Make sure all connections are made rst. 123456+-Battery+-BatteryAAAAAA
10Audio Input SelectionPC Sound Card Input Connection•       There are three 3.5mm input jacks for true 5.1 PC Sound card on the rear panel of the          subwoofer. Please check your sound card manual for the proper connections.•       Press the “INPUT” button to switch the input until the “PC IN” LED lights up.Line In Input Connection•       Making connection with your speaker to any AV system, game console, etc. using the          RCA input on the rear panel of subwoofer.•       Press the “INPUT” button to switch the input until the “LINE IN” LED lights up.Optical Input Connection•       Use an optical cable to connect your device to the optical port on the rear panel of the          subwoofer. (Optical cable is not included)•       Press the “INPUT” button to switch the input until the “OPTICAL” LED lights up.AUX IN Input Connection•       You can connect any laptop, tablet, smartphone, MP3 player, etc. by using a 3.5mm AUX         cable and plugging it into the AUX jack on the rear side of the control console.•       Press the “INPUT” button to switch the input until the “AUX IN” LED lights up.   Adjust VolumeRotate the volume knob to adjust the entire system’s volume. The LED bar will turn into a volume status bar when you start to rotate the knob. It will resume the display status after adjustments are made. Adjust Bass VolumePress “BASS” button and the “BASS” LED will turn on. The LED bar will turn into bass level status bar. Adjust the bass volume by rotating the knob. It will resume the display status after adjustments are made.Bluetooth Input Connection•       Press the “INPUT” button to switch the input until the “BLUETOOTH” LED lights up.•       First time pairing; the P560 will automatically go into pairing mode.•       Go to your Bluetooth device and select the device named “P560”.•       If the system is turned off, it will automatically search for the latest connected device when          turned back on. If the device cannot be found, it will enter into pairing mode.•       If you want to pair another new device, you can press and hold the “PLAY” button for 5 seconds          on the IR remote control to trigger the system into pairing mode.
11Still can’t connect1.  Be sure to check your room environment. Today’s Bluetooth technology has a designed limit of approximately 30 feet, line     of sight. This generally means your best result will be limiting your source device and speakers to the same room. Extremely      large rooms, or rooms with lost of wireless electronics, wi- routers, radio transmitters, etc, may affect your ability to pair.            2.  Check to see if any other devices are already connected to the P560. The speakers can only pair with one device at a time.      If you need to unpair, choose “Forget this device” from your source. Then follow Bluetooth Input Connections on page #11.      3.  Check the battery life on your source device and charge if necessary. Most devices operate best when charged above 20%      minimum battery level.         Can’t connect for the first time1.  Turn off the speaker system by pressing the POWER button.2.  Check your Bluetooth source device and make sure you have found the section that allows you to see nearby Bluetooth     products. If you see the P560 on the list, but cannot connect, you may need to search again. To start fresh with your      Bluetooth device, select “Forget this device”, and remove the P560 from the list. You may need to turn off the Bluetooth      function on your device to fully clear your list.             3.  Turn on the speaker system again by pressing the POWER button and select Bluetooth as input by pressing the INPUT      button until BLUETOOTH LED is on; the LED will be blinking rapidly showing that the speaker system is in pairing mode. 4.  Return to your source device, and re-enable the Bluetooth function. Look for the P560 speakers to show back up on the list..5.  Select the device on the list and the BLUETOOTH LED will become solid if it is connected successfully.   Can’t connect when returning1.  If the P560 does not automatically connect back with your Bluetooth-enabled device, you may need to physically go into     your device’s Bluetooth settings and select “P560” to reconnect.       2.  If the above step does not work, see steps 1-5 in the “Can’t connect for the rst time” section above.     Audio is choppy, has erratic static, or keeps disconnecting1.  Be sure to check the room environment. Today’s Bluetooth technology has a designed limit of approximately 30 feet, line of  sight. This generally means your best results will be limiting your source device and speakers to the same room. Extremely  large rooms, or rooms with a lot of wireless electronics, routers, etc, may affect the quality of sound, connection, or  connection consistency.        2.  Check for obstructions, walls, or other objects that might impede the Bluetooth signal.3. Try returning to the source device to a closer proximity with your speakers.       ADDITIONAL SUPPORTThe latest updated video tutorials, FAQ, and product feature specications are available online 24/7 at http://cyberacoustics.com/P560 or Technical support is available at 360-883-0333, M-F 8am to 5pm PST.TROUBLE SHOOTING BLUETOOTH TROUBLE SHOOTING Power button is not turned on. Press the power button back and forthand check for the blue LED indicator light to come on.Verify the AC power cord is plugged into the wall outlet.Check if the wall outlet or power strip you are using is actually getting power, i.e. not a switched outlet.Speaker Does Not ProduceSoundSYMPTOMSpeaker System Will Not Power SOLUTIONVerify the speaker is getting power. Check the steps above.Verify that all cables are plugged into the correct jacks or that the Bluetooth is paired correctly. Turn the speaker volume down by 25% or 50%.Adjust the bass volume control to test for maximum and minimum output. You may also need to move the subwoofer either closer or farther away from a wall or corner to affect the sound performance.Adjust the sound source’s master volume control by balancing the volume until it’s centered.Sound Is Distorted
12FCC STATEMENT1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:           (1) This device may not cause harmful interference.           (2) This device must accept any interference received, including interference that may cause undesired operation.             2. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority     to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15            of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a            residential installation.                                 This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.                                                            Performance Specifications A:   Watts: 530W RMS      Satellites – 75W watts/ch x 5 @ 8 ohm – 10% THD      Subwoofer – 155Watts @ 4 ohm – 10% THD B:   Speakers size:      Satellites – 4.3” (W) x 3.7” (D) x 7.0” (H)      Center Satellites – 6.5” (W) x 3.7” (D) x 4.0” (H)      Subwoofer – 11” (W) x 13” (D) x 11.5” (H)C:  Drivers size:      3” dynamic satellite drivers      8” poly-carbon high excursion subD:   Frequency response: 28Hz – 20KHz  Wall Mounting You can mount your satellite speakers with the appropriate hardware (not included).• Do not mount the speakers on thin plywood or on a wall with a soft surface material. The speakers may fall, possibly    damaging the speakers or causing personal injury.• Do not affix the speakers to a wall using nails, adhesives, or unstable hardware. Long-term use and vibration may cause   the speakers to fall.• To avoid accidents resulting from tripping over loose speaker cables, affix the cables to the wall and floor.• Mount the speakers in a wall location that will be less likely to result in injury to an individual’s head or property damage.WarrantyFor warranty information and registration, please go to www.cyberacoustics.com/rockford  FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Navigation menu