CyberTAN Technology BU067HS BT Module User Manual

CyberTAN Technology Inc. BT Module

User Manual

COMPANY CONFIDENTIAL 2! BT Module YouSong lndustrial District, Longhua Town, Baoan, ShenZhen Tel: +86-755-28128988#69085 Fax:+86-755-28129800#64886 Product Specification !M26H004.01 FCC ID:ʳˡˋˌˀ˕˨˃ˉˊ˛˦M26H004.01 FCC ID: N89-BU067HS
COMPANY CONFIDENTIAL 2 CONTENTS 0. REVISION HISTORY 1. INTRODUCTION 1.1 SCOPE 1.2 FEATURE 1.3 FUNCTIONAL BLOCK DIAGRAM 2. MECHANICAL SPECIFICATION 2.1 Module demension 2.2 WTB Connector Specification 2.3 WTB connector Pin definition 3. ELECTRICAL SPECIFICATION 3.1 OPERATING CONDITION 3.2 BT RF SPECIFICATION 3.3 ON-BOARD ANTENNA SPECIFICATION 4. QUALITY 5. APPENDIX 5.1 Label Information...............................................................................................................................7 5.2 Package Information .........................................................................................................................8
COMPANY CONFIDENTIAL 3 0. Revision History Date Document revision Product revision Change Description 2013/3/4 00 1. Initial release 2013/3/18 01 1. new add schematic 2. new add BOM 3. new add PCB layout 2013-5-15 02 1. update PCBA picture 2. update outline because add shielding 3. update label and package information
COMPANY CONFIDENTIAL 4 1. Introduction Project Name: 3D TV BT Module Project Number: M26H004.01. This documentation describes the engineering requirements specification of 3D TV BT Module. It is a confidential document of Foxconn. 1.1 Scope The BT Module is compliant to Bluetooth 4.0 and EDR compliant: Carrier Frequency: 2402MHz ~ 2480 MHz Carrier Spacing: 1.0MHz Duplexing: TDD Modulation: FHSS/ GFSK, pi/4-DQPSK, 8DPSK Symbol Rate: 1Mbps (GFSK), 2Mbps (pi/4-DQPSK), 3Mbps (8DPSK) This module is designed with 8pin WTB connector and USB Interface, and it is installed as a client device in TV platform. 1.2 Feature Bluetooth 4.0+EDR compliant Programmable output power control meets Class 1, Class 2 requirements. Support PC and TV applications without external memory. Support 3D Glass and BT remote control device 1.3 Functional Block Diagram Sample picture is as below Top View Bottom View
COMPANY CONFIDENTIAL 5 2. Mechanical Specification 2.1 Module dimension Module Dimension: Typical PCB size (W×L): 18mm ×36mm. 2.2 WTB Connector Specification 8pin side entry type WTB CONN, 1.25mm pitch, detail spec as below: 2.3 WTB connector Pin definition Pin No Pin Name I/O Description 1 BT_DEVICE_WAKE(GPIO_0) I Allows the SOC host to wake up the BT device 2 BT_HOST_WAKE(GPIO_1) O Allows the BT device to wake up the SOC host 3 USB_5V PWR DC +5V power input 4 HUSBDM I/O USB Data D- 5 HUSBDP I/O USB Data D+ 6 GND GND Ground 7 3D_SYNC(GPIO_5) I 3D sync clock input 8 BT_RST I BT device reset 8 1 Unit: mm
COMPANY CONFIDENTIAL 6 3. Electrical Specification 3.1 Operating Condition Parameter Condition Min. Typ. Max. Unit DC Input USB 5V 4.5 5.0 5.5 V Tx Current 0.35 Rx Current 0.17 Module Current (DC input nominal) Standby Current 0.01 A Operating Temperature -- 0 +60 Storage Temperature -- -40 +85 3.2 BT RF Specification Items Contents TX Characteristics Min. Typ. (@5.0V/25 ) Max. Unit 1. Power Levels BT Output Power (Basic Data Rate)@Class 2 -6 2.0 4 dBm 2. Initial Carrier Frequency Tolerance Average Offset -75 -4.8 75 kHz 3. Carrier Drift Drift Rate DH1 -20 -5.54 20 kHz/50us DH3 -20 6.11 20 kHz/50us DH5 -20 5.38 20 kHz/50us Average Drift DH1 -25 -5 25 kHz DH3 -40 -5 40 kHz DH5 -40 -1 40 kHz 4. Modulation Characteristic F1avg 140 155 175 kHz F2max 115 130 kHz F1/F2 Ratio 0.8 0.94 5. EDR Relative Transmit Power 2Mbps: P[DQPSK]-P[GFSK] -4 0.30 1 dB 3Mbps: P[8DPSK]-P[GFSK] -4 0.25 1 dB 6. EDR Carrier Frequency Stability and Modulation Accuracy 2Mbps: /4 DQPSK Initial Frequency Error: ω -75 -6.1 75 kHz Frequency Error: ω -10 -2.2 10 kHz Block Frequency Error: ω ω -75 -7.5 75 kHz RMS DEVM - 0.062 0.2 Peak DEVM - 0.158 0.35 99% DEVM (% Symbols <=0.3) 99% 100% 3Mbps: 8DPSK Initial Frequency Error: ω -75 -9 75 kHz Frequency Error: ω -10 -1.5 10 kHz Block Frequency Error: ω ω -75 -10 75 kHz RMS DEVM - 0.05 0.13 Peak DEVM - 0.13 0.25 99% DEVM (% Symbols <=0.13) 99% 100%
COMPANY CONFIDENTIAL 7 3.3 On-board Antenna Specification Operating Frequency 2.40~2.5GHz VSWR <=2.0:1 Antenna Type Chip ANT 4. Quality The product quality must be followed-up by Foxconn factory quality control system. 5. Appendix 5.1 Label Information Items Contents RX Characteristics Min. Typ. (@5.0V/25 ) Max. Unit 1. Minimum Input Level Sensitivity GFSK (1Mbps) - -87 -70 dBm /4 DQPSK (2Mbps) - -87 -70 dBm 8DPSK (3Mbps) - -80 -70 dBm 2. Maximum Input Level GFSK (1Mbps) -20 0 dBm /4 DQPSK (2Mbps) -20 -14 dBm 8DPSK (3Mbps) -20 -14 dBm
COMPANY CONFIDENTIAL 8 5.2 Package Information
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: N89-BU067HS ”. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

Navigation menu