CyberTAN Technology NU260HS 2.4G Module User Manual 8

CyberTAN Technology Inc. 2.4G Module 8

Contents

8. User Manual

   COMPANY  CONFIDENTIAL             1               IEEE 802.11b/g/n WLAN and Bluetooth Combo Card    Project Name  Marvell 88W8797 WLAN/BT Combo Card Customer  Hisense Foxconn Part No.  M26H003.00 Customer Part No.  TBD                             HON HAI PRECISION IND. CO., LTD. No.2, 2nd Dong Huan Road, 10th YouSong lndustrial District, Longhua Town, Baoan, ShenZhen Tel: +86-755-28128988#80633     Fax:+86-755-28129800#64886 Product Specification
   COMPANY  CONFIDENTIAL             2 CONTENTS 0. REVISION HISTORY 1. INTRODUCTION 1.1 SCOPE 1.2 FEATURE 1.3 APPLICATION 2. MECHANICAL SPECIFICATION 2.1 MODULE DIMENSION 2.2 HOST INTERFACE CONNECTOR 2.3 RF CONNECTOR (OPTION) 3. ELECTRICAL SPECIFICATION 3.1 OPERATING CONDITION 3.2 WIFI RF SPECIFICATION 3.2.1    802.11b Mode 3.2.2    802.11g Mode 3.2.3 802.11n HT20 Mode 3.2.4 802.11n HT40 Mode 3.3 ON-BOARD ANTENNA SPECIFICATION 3.3 BT RF SPECIFICATION 4. COMPATIBILITY AND CERTIFICATION INFORMATION 5. QUALITY 6. APPENDIX APPENDIX A - LABEL INFORMATION APPENDIX B - PACKAGE INFORMATION
   COMPANY  CONFIDENTIAL             3 0. Revision History  Date  Document revision Product revision  Change Description 2012/11/20 00   1. Initial release   2013/06/06 01   1. add label and package information 2013-10-17 02   Update PCB bottom view picture (add FCC label)
   COMPANY  CONFIDENTIAL             4 1. Introduction  Project Name: Marvell 88W8797 WLAN/BT Combo Card   Project Number: M26H003.00  This documentation describes the engineering requirements specification of 88W8797 (WLAN+BT) combo Card. It is a confidential document of Foxconn.  1.1 Scope    This combo design is based on the Marvell 8797 single-chip solution. It’s operating in 2.4GHz, compatible with the IEEE 802.11b/g/n standard and Bluetooth BT4.0 standard. The 802.11n data rate provides for MCS0 to MCS7 (HT20,HT40). The 802.11g data rate provides for 54, 48, 36, 24, 18, 12, 9, 6Mbps, and 802.11b data rate provides for 11, 5.5, 2, 1Mbps. In addition, it’s also compatible with BT4.0. This combo card has implemented some efficient mechanisms in its software and hardware to maximize the performance of WLAN and BT.    1.2 Feature    Compatible with IEEE 802.11b/g/n standard     Compatible with BT4.0 + HS (supports Low Energy (LE)   Support external or on-board antenna for both WiFi and BT   Support two Antennas (WiFi*2 and BT shared one ANT)       or three antennas for WiFi *2 and BT*1 ( preferred )   2x2 MIMO spatial streams supporting data rates up to MCS15(300Mbps)   Better WiFi and BT Coexistence performance
   COMPANY  CONFIDENTIAL             5 1.3 Application    WLAN/Bluetooth/FM enabled cellular handsets   Portable audio/video devices and accessories   Personal computing systems including pads, tablets and slates   Wireless home audio and video entertainment systems including TV, set-top boxes, media servers and gaming platforms      Sample picture as bellow                          TOP VIEW                                                          BOTTOM VIEW                                           * note1, the sample picture is just for reference only.
   COMPANY  CONFIDENTIAL             6 2. Mechanical Specification 2.1 Module Dimension   PCB: FR4, 4layers, one side design Typical PCB size (W×L): 40mm ×46.45mm                                                                                                                          Unit: mm 2.2 Host Interface Connector  This module use 8pins BTW connector for the Host-Module interface.      WTB 8Pin 1.25mm pin pitch SMD MALE
   COMPANY  CONFIDENTIAL             7    Here is the pin-out signals of module’s connector. The pin number is refer to “Item2.2.1 module dimension”.  Table 1: Host-Module Connector Pin-out Signals No. Pin-Out  Description 1 VCC VCC 5V 2  GND  GND 3  DN  USB Data DN 4  DP  USB Data DP 5  GND  GND 6  Reset  Reset (active low, input) Once asserts low, all digital logic in the chip is reset to default power up states. This pin has internal pull-up resistor on module. 7  Wakeup  GPIO interrupt (host-to-chip wakeup interrupt) (input) (default) Host Wakeup: chip-to-host wakeup interrupt (output) 8  PDn  Full Power Down (active low, input) This pin has internal pull-up resistor on module.
   COMPANY  CONFIDENTIAL             8 2.3 RF Connector (Option) This module use U.F.L type RF connector for external WiFi/BT antenna connecting.
   COMPANY  CONFIDENTIAL             9 3. Electrical Specification 3.1 Operating Condition  Parameter  Condition  Min.  Typ.  Max.  Unit DC Input    5V  4.5  5  5.5  V Module Current (DC input nominal) WiFi TX only and BT sleep    200   mA WiFi RX only and BT sleep    176   BT TX only    172   BT RX only    181   WiFi/BT co-existence    220   Standby   with connection AP   180   Operating Temperature  --  0    +60   Storage Temperature  --  -30    +85   3.2 WiFi RF Specification 3.2.1    802.11b Mode                                                                                           Items Contents   Standard  IEEE802.11b   Modulation Type  DSSS / CCK   Frequency range  2412MHz~2472MHz   Channel  CH1 to CH13     Data rate  1, 2, 5.5, 11Mbps TX Characteristics(per chain)  Min. Typ.  Max.  Unit  1. Transmitter Output Power               1) 11b Target Power  15  17  19  dBm   2. Spectrum Mask @ target power               1) fc +/-11MHz to +/-22MHz      -30  dBr       2) fc > +/-22MHz                                        -50  dBr   3. Frequency Error    -25  -1  25  ppm   4 Constellation Error( peak EVM)@ target power            1) 1~11Mbps      -31    dB   RX Characteristics(per chain)  Min. Typ.  Max.  Unit   5 Minimum Input Level Sensitivity             1) 1Mbps (FER 8%)    -97.6  -83  dBm       2) 2Mbps (FER 8%)    -94.4  -80  dBm       3) 5.5Mbps (FER 8%)    -92.6  -79  dBm       4) 11Mbps (FER 8%)    -89.0  -76  dBm   6 Maximum Input Level (FER 8%)  -10      dBm
   COMPANY  CONFIDENTIAL             10 3.2.2    802.11g Mode  Items Contents Standard  IEEE802.11g   Modulation Type  OFDM   Frequency range  2412MHz~2472MHz   Channel  CH1 to CH13   Data rate  6, 9, 12, 18, 24, 36, 48, 54Mbps   TX Characteristics (per chain)  Min.  Typ.  Max.  Unit   1. Transmitter Output Power                 1) 11g Target Power  13  15  17  dBm   2. Spectrum Mask @ target power             1) at fc +/- 11MHz      -20  dBr       2) at fc +/- 20MHz      -28  dBr       3) at fc > +/-30MHz      -40  dBr   3 Constellation Error(EVM)@ target power             1) 6Mbps      -5  dB       2) 9Mbps      -8  dB       3) 12Mbps      -10  dB       4) 18Mbps      -13  dB       5) 24Mbps      -16  dB       6) 36Mbps      -19  dB       7) 48Mbps      -22  dB       8) 54Mbps    -33  -25  dB   4 Frequency Error    -25  -1.1  +25  ppm   RX Characteristics (per chain)  Min.  Typ.  Max.  Unit   5 Minimum Input Level Sensitivity               1) 6Mbps (PER    10%)   -90.8 -85  dBm       2) 9Mbps (PER    10%)   -90.3 -84  dBm       3) 12Mbps (PER    10%)   -88.1 -82  dBm       4) 18Mbps (PER    10%)    -86.2  -80  dBm       5) 24Mbps (PER    10%)    -83.3  -77  dBm       6) 36Mbps (PER    10%)   -80.0 -73  dBm       7) 48Mbps (PER    10%)   -75.4 -69  dBm       8) 54Mbps (PER    10%)    -73.5  -68  dBm   6 Maximum Input Level (PER    10%)  -20      dBm
   COMPANY  CONFIDENTIAL             11 3.2.3 802.11n HT20 Mode                              Items Contents Standard IEEE802.11n HT20 @ 2.4GHz Modulation type MIMO-OFDM   Channel  CH1 to CH13   Data rate (MCS index)  MCS0/1/2/3/4/5/6/7 TX Characteristics(per chain) Min. Typ. Max. Unit  1. Transmitter Output Power          1) 11n HT20 Target Power 13  15  17 dBm  2. Spectrum Mask @ target power          1) at fc +/- 11MHz      -20  dBr       2) at fc +/- 20MHz      -28  dBr       3) at fc > +/-30MHz   -45 dBr  3. Constellation Error(EVM)@ target power          1) MCS0   -5 dB      2) MCS1   -10 dB      3) MCS2      -13  dB       4) MCS3      -16  dB       5) MCS4   -19 dB      6) MCS5   -22 dB      7) MCS6   -25 dB      8) MCS7  -32 -28 dB  4. Frequency Error  -25  -1.2  +25  ppm   RX Characteristics (per chain) Min.  Typ.  Max. Unit   5. Minimum Input Level Sensitivity         1) MCS0 (PER  10%)  -91.0 -82 dBm     2) MCS1 (PER  10%)  -88.3 -79 dBm     3) MCS2 (PER  10%)  -85.9 -77 dBm      4) MCS3 (PER    10%)    -83.5 -74  dBm       5) MCS4 (PER    10%)    -80.2 -70  dBm      6) MCS5 (PER  10%)  -75.5 -66 dBm     7) MCS6 (PER  10%)  -74.1 -65 dBm     8) MCS7 (PER  10%)  -71.9 -64 dBm  6. Maximum Input Level (PER  10%) -20   dBm
   COMPANY  CONFIDENTIAL             12 3.2.4 802.11n HT40 Mode      3.3 On-board Antenna Specification  Operating Frequency  2.412~2.472GHz VSWR(ANT1and ANT2)  <=2.0:1 Isolation(ANT1& ANT2)  >=15dB Antenna Type  Metal ANT   Items Contents Standard IEEE802.11n HT40 @ 2.4GHz Modulation type MIMO-OFDM   Channel  CH3 to CH11   Data rate (MCS index)  MCS0/1/2/3/4/5/6/7 TX Characteristics(per chain) Min. Typ. Max. Unit  1. Transmitter Output Power            1) 11n HT40 Target power 12  14  16 dBm  2. Spectrum Mask @ target power          1) at fc +/- 22MHz      -20  dBr       2) at fc +/- 40MHz      -28  dBr       3) at fc > +/-60MHz   -45 dBr  3. Constellation Error(EVM)@target power          1) MCS0   -5 dB      2) MCS1   -10 dB      3) MCS2      -13  dB       4) MCS3      -16  dB       5) MCS4   -19 dB      6) MCS5   -22 dB      7) MCS6   -25 dB      8) MCS7  -32 -28 dB  4. Frequency Error    -25  -1.1 +25  ppm   RX Characteristics (per chain) Min.  Typ. Max. Unit   5. Minimum Input Level Sensitivity         1) MCS0 (PER  10%)  -87.2 -79 dBm     2) MCS1 (PER  10%)  -84.1 -76 dBm     3) MCS2 (PER  10%)  -81.3 -74 dBm      4) MCS3 (PER    10%)    -79.7 -71  dBm       5) MCS4 (PER    10%)    -74.5 -67  dBm      6) MCS5 (PER  10%)  -73.0 -63 dBm     7) MCS6 (PER  10%)  71.2 -62 dBm     8) MCS7 (PER  10%)  -68.8 -61 dBm  6. Maximum Input Level (PER  10%) -20   dBm
   COMPANY  CONFIDENTIAL             13 3.3 BT RF Specification  4. Compatibility and Certification Information The 8797 combo module shall pass the standard test plan, which includes hardware compatibility and reliability, and software compatibility test. 5. Quality The product quality must be followed-up by Foxconn factory quality control system.   Items Contents Standard  BTv4.0     Modulation technology  HFSS Modulation type GFSK, π/4-DQPSK, 8DPSK Frequency range 2402MHz ~ 2480MHz Numbers of Channel 79 channels with 1MHz Bandwidth   Data rate (MCS index)  1Mbps/2Mbps/3Mbps TX Characteristics Min.  Typ. Max. Unit   1. BDR Transmitter Output Power                1) Target power (class2) -6  2.0  +4 dBm  2. BDR Initial Carrier Freq. Tolerance -75 -1.3 +75 KHz  3. BDR Carrier Drift          1) Drift Rate/50us -20 4.7 +20 KHz      2) Average Drift    -25  -1  +25  dB  dB   -40  +2  +40  KHz  KHz   -40 0 +40 KHz KHz  4. BDR Modulation Characteristic      1)    F1avg(kHz) 140 162.1 175 KHz  2)    F2avg(kHz) 115 146.5 - KHz  3   F1/F2 Ratio  0.8  0.9  -  -   5 EDR Carrier Frequency Stability and   Modulation Accuracy          1)    Initial Frequency Error -75 -1.3 +75 KHz  2)    Frequency Error -10 0.6 +10 KHz  3)    Block Frequency Error -75 -1.2 +75 KHz  4   RMS DEVM @2Mbps 0.2 0.045  -  5   Peak DEVM @2Mbps  0.35  0.1    -   6 99% DEVM @% Symbols <= 0.3 (2Mbps)  99%  100%   -   7   RMS DEVM @3Mbps 0.13 0.037  -  8   Peak DEVM @3Mbps 0.25 0.08  -  9 99% DEVM @% Symbols <= 0.2(3Mbps) 99% 100%  -  RX Characteristics     Unit  6. Minimum Input Level Sensitivity               1) BDR Single slot sensitivity (BER    0.1%)      -70  dBm      2) BDR Multi slot sensitivity (BER  0.1%)   -70 dBm     3) EDR sensitivity@2Mbps (BER  0.01%)   -70 dBm     4) EDR sensitivity@3Mbps (BER  0.01%)   -70 dBm  7. Maximum Input Level (BER  0.1%) -20   dBm
   COMPANY  CONFIDENTIAL             14 6. Appendix  Appendix A - Label Information
   COMPANY  CONFIDENTIAL             15 Appendix B - Package Information
COMPANY  CONFIDENTIAL Federal Communication Commission Interference Statement   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.   However, there is no guarantee that interference will not occur in a particular installation.   If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:   - Reorient or relocate the receiving antenna.   - Increase the separation between the equipment and receiver.   - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.   - Consult the dealer or an experienced radio/TV technician for help.   FCC Caution:   Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.   This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  (1) This device may not cause harmful interference, and  (2) This device must accept any interference received, including interference that may cause undesired operation.  FCC Radiation Exposure Statement:     This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter.     This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.    IMPORTANT NOTE:   In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.      End Product Labeling     The final end product must be labeled in a visible area with the following:         “Contains FCC ID: N89-NU260HS”.         Manual Information to the End User     The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

Navigation menu