CyberTAN Technology NU260HS 2.4G Module User Manual

CyberTAN Technology Inc. 2.4G Module

Contents

User Manual

COMPANY CONFIDENTIAL 1 IEEE 802.11b/g/n WLAN and Bluetooth Combo Card Project Name Marvell 88W8797 WLAN/BT Combo Card Customer Hisense Foxconn Part No. M26H003.00 Customer Part No. TBD HON HAI PRECISION IND. CO., LTD. No.2, 2nd Dong Huan Road, 10th YouSong lndustrial District, Longhua Town, Baoan, ShenZhen Tel: +86-755-28128988#80633 Fax:+86-755-28129800#64886 Product Specification
COMPANY CONFIDENTIAL 2 CONTENTS 0. REVISION HISTORY 1. INTRODUCTION 1.1 SCOPE 1.2 FEATURE 1.3 APPLICATION 2. MECHANICAL SPECIFICATION 2.1 MODULE DIMENSION 2.2 HOST INTERFACE CONNECTOR 2.3 RF CONNECTOR (OPTION) 3. ELECTRICAL SPECIFICATION 3.1 OPERATING CONDITION 3.2 WIFI RF SPECIFICATION 3.2.1 802.11b Mode 3.2.2 802.11g Mode 3.2.3 802.11n HT20 Mode 3.2.4 802.11n HT40 Mode 3.3 ON-BOARD ANTENNA SPECIFICATION 3.3 BT RF SPECIFICATION 4. COMPATIBILITY AND CERTIFICATION INFORMATION 5. QUALITY 6. APPENDIX APPENDIX A - LABEL INFORMATION APPENDIX B - PACKAGE INFORMATION
COMPANY CONFIDENTIAL 3 0. Revision History Date Document revision Product revision Change Description 2012/11/20 00 1. Initial release 2013/06/06 01 1. add label and package information 2013-10-17 02 Update PCB bottom view picture (add FCC label)
COMPANY CONFIDENTIAL 4 1. Introduction Project Name: Marvell 88W8797 WLAN/BT Combo Card Project Number: M26H003.00 This documentation describes the engineering requirements specification of 88W8797 (WLAN+BT) combo Card. It is a confidential document of Foxconn. 1.1 Scope This combo design is based on the Marvell 8797 single-chip solution. It’s operating in 2.4GHz, compatible with the IEEE 802.11b/g/n standard and Bluetooth BT4.0 standard. The 802.11n data rate provides for MCS0 to MCS7 (HT20,HT40). The 802.11g data rate provides for 54, 48, 36, 24, 18, 12, 9, 6Mbps, and 802.11b data rate provides for 11, 5.5, 2, 1Mbps. In addition, it’s also compatible with BT4.0. This combo card has implemented some efficient mechanisms in its software and hardware to maximize the performance of WLAN and BT. 1.2 Feature  Compatible with IEEE 802.11b/g/n standard  Compatible with BT4.0 + HS (supports Low Energy (LE)  Support external or on-board antenna for both WiFi and BT  Support two Antennas (WiFi*2 and BT shared one ANT） or three antennas for WiFi *2 and BT*1 ( preferred )  2x2 MIMO spatial streams supporting data rates up to MCS15(300Mbps)  Better WiFi and BT Coexistence performance
COMPANY CONFIDENTIAL 5 1.3 Application  WLAN/Bluetooth/FM enabled cellular handsets  Portable audio/video devices and accessories  Personal computing systems including pads, tablets and slates  Wireless home audio and video entertainment systems including TV, set-top boxes, media servers and gaming platforms Sample picture as bellow TOP VIEW BOTTOM VIEW * note1, the sample picture is just for reference only.
COMPANY CONFIDENTIAL 6 2. Mechanical Specification 2.1 Module Dimension PCB: FR4, 4layers, one side design Typical PCB size (W×L): 40mm ×46.45mm Unit: mm 2.2 Host Interface Connector This module use 8pins BTW connector for the Host-Module interface.  WTB 8Pin 1.25mm pin pitch SMD MALE
COMPANY CONFIDENTIAL 7  Here is the pin-out signals of module’s connector. The pin number is refer to “Item2.2.1 module dimension”. Table 1: Host-Module Connector Pin-out Signals No. Pin-Out Description 1 VCC VCC 5V 2 GND GND 3 DN USB Data DN 4 DP USB Data DP 5 GND GND 6 Reset Reset (active low, input) Once asserts low, all digital logic in the chip is reset to default power up states. This pin has internal pull-up resistor on module. 7 Wakeup GPIO interrupt (host-to-chip wakeup interrupt) (input) (default) Host Wakeup: chip-to-host wakeup interrupt (output) 8 PDn Full Power Down (active low, input) This pin has internal pull-up resistor on module.
COMPANY CONFIDENTIAL 8 2.3 RF Connector (Option) This module use U.F.L type RF connector for external WiFi/BT antenna connecting.
COMPANY CONFIDENTIAL 9 3. Electrical Specification 3.1 Operating Condition Parameter Condition Min. Typ. Max. Unit DC Input 5V 4.5 5 5.5 V Module Current (DC input nominal) WiFi TX only and BT sleep 200 mA WiFi RX only and BT sleep 176 BT TX only 172 BT RX only 181 WiFi/BT co-existence 220 Standby with connection AP 180 Operating Temperature -- 0 +60 Storage Temperature -- -30 +85 3.2 WiFi RF Specification 3.2.1 802.11b Mode Items Contents Standard IEEE802.11b Modulation Type DSSS / CCK Frequency range 2412MHz~2472MHz Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics(per chain) Min. Typ. Max. Unit 1. Transmitter Output Power 1) 11b Target Power 15 17 19 dBm 2. Spectrum Mask @ target power 1) fc +/-11MHz to +/-22MHz -30 dBr 2) fc > +/-22MHz -50 dBr 3. Frequency Error -25 -1 25 ppm 4 Constellation Error( peak EVM)@ target power 1) 1~11Mbps -31 dB RX Characteristics(per chain) Min. Typ. Max. Unit 5 Minimum Input Level Sensitivity 1) 1Mbps (FER 8%) -97.6 -83 dBm 2) 2Mbps (FER 8%) -94.4 -80 dBm 3) 5.5Mbps (FER 8%) -92.6 -79 dBm 4) 11Mbps (FER 8%) -89.0 -76 dBm 6 Maximum Input Level (FER 8%) -10 dBm
COMPANY CONFIDENTIAL 10 3.2.2 802.11g Mode Items Contents Standard IEEE802.11g Modulation Type OFDM Frequency range 2412MHz~2472MHz Channel CH1 to CH13 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics (per chain) Min. Typ. Max. Unit 1. Transmitter Output Power 1) 11g Target Power 13 15 17 dBm 2. Spectrum Mask @ target power 1) at fc +/- 11MHz -20 dBr 2) at fc +/- 20MHz -28 dBr 3) at fc > +/-30MHz -40 dBr 3 Constellation Error(EVM)@ target power 1) 6Mbps -5 dB 2) 9Mbps -8 dB 3) 12Mbps -10 dB 4) 18Mbps -13 dB 5) 24Mbps -16 dB 6) 36Mbps -19 dB 7) 48Mbps -22 dB 8) 54Mbps -33 -25 dB 4 Frequency Error -25 -1.1 +25 ppm RX Characteristics (per chain) Min. Typ. Max. Unit 5 Minimum Input Level Sensitivity 1) 6Mbps (PER 10%) -90.8 -85 dBm 2) 9Mbps (PER 10%) -90.3 -84 dBm 3) 12Mbps (PER 10%) -88.1 -82 dBm 4) 18Mbps (PER 10%) -86.2 -80 dBm 5) 24Mbps (PER 10%) -83.3 -77 dBm 6) 36Mbps (PER 10%) -80.0 -73 dBm 7) 48Mbps (PER 10%) -75.4 -69 dBm 8) 54Mbps (PER 10%) -73.5 -68 dBm 6 Maximum Input Level (PER 10%) -20 dBm
COMPANY CONFIDENTIAL 11 3.2.3 802.11n HT20 Mode Items Contents Standard IEEE802.11n HT20 @ 2.4GHz Modulation type MIMO-OFDM Channel CH1 to CH13 Data rate (MCS index) MCS0/1/2/3/4/5/6/7 TX Characteristics(per chain) Min. Typ. Max. Unit 1. Transmitter Output Power 1) 11n HT20 Target Power 13 15 17 dBm 2. Spectrum Mask @ target power 1) at fc +/- 11MHz -20 dBr 2) at fc +/- 20MHz -28 dBr 3) at fc > +/-30MHz -45 dBr 3. Constellation Error(EVM)@ target power 1) MCS0 -5 dB 2) MCS1 -10 dB 3) MCS2 -13 dB 4) MCS3 -16 dB 5) MCS4 -19 dB 6) MCS5 -22 dB 7) MCS6 -25 dB 8) MCS7 -32 -28 dB 4. Frequency Error -25 -1.2 +25 ppm RX Characteristics (per chain) Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity 1) MCS0 (PER 10%) -91.0 -82 dBm 2) MCS1 (PER 10%) -88.3 -79 dBm 3) MCS2 (PER 10%) -85.9 -77 dBm 4) MCS3 (PER 10%) -83.5 -74 dBm 5) MCS4 (PER 10%) -80.2 -70 dBm 6) MCS5 (PER 10%) -75.5 -66 dBm 7) MCS6 (PER 10%) -74.1 -65 dBm 8) MCS7 (PER 10%) -71.9 -64 dBm 6. Maximum Input Level (PER 10%) -20 dBm
COMPANY CONFIDENTIAL 12 3.2.4 802.11n HT40 Mode 3.3 On-board Antenna Specification Operating Frequency 2.412~2.472GHz VSWR(ANT1and ANT2) <=2.0:1 Isolation(ANT1& ANT2) >=15dB Antenna Type Metal ANT Items Contents Standard IEEE802.11n HT40 @ 2.4GHz Modulation type MIMO-OFDM Channel CH3 to CH11 Data rate (MCS index) MCS0/1/2/3/4/5/6/7 TX Characteristics(per chain) Min. Typ. Max. Unit 1. Transmitter Output Power 1) 11n HT40 Target power 12 14 16 dBm 2. Spectrum Mask @ target power 1) at fc +/- 22MHz -20 dBr 2) at fc +/- 40MHz -28 dBr 3) at fc > +/-60MHz -45 dBr 3. Constellation Error(EVM)@target power 1) MCS0 -5 dB 2) MCS1 -10 dB 3) MCS2 -13 dB 4) MCS3 -16 dB 5) MCS4 -19 dB 6) MCS5 -22 dB 7) MCS6 -25 dB 8) MCS7 -32 -28 dB 4. Frequency Error -25 -1.1 +25 ppm RX Characteristics (per chain) Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity 1) MCS0 (PER 10%) -87.2 -79 dBm 2) MCS1 (PER 10%) -84.1 -76 dBm 3) MCS2 (PER 10%) -81.3 -74 dBm 4) MCS3 (PER 10%) -79.7 -71 dBm 5) MCS4 (PER 10%) -74.5 -67 dBm 6) MCS5 (PER 10%) -73.0 -63 dBm 7) MCS6 (PER 10%) 71.2 -62 dBm 8) MCS7 (PER 10%) -68.8 -61 dBm 6. Maximum Input Level (PER 10%) -20 dBm
COMPANY CONFIDENTIAL 13 3.3 BT RF Specification 4. Compatibility and Certification Information The 8797 combo module shall pass the standard test plan, which includes hardware compatibility and reliability, and software compatibility test. 5. Quality The product quality must be followed-up by Foxconn factory quality control system. Items Contents Standard BTv4.0 Modulation technology HFSS Modulation type GFSK, π/4-DQPSK, 8DPSK Frequency range 2402MHz ~ 2480MHz Numbers of Channel 79 channels with 1MHz Bandwidth Data rate (MCS index) 1Mbps/2Mbps/3Mbps TX Characteristics Min. Typ. Max. Unit 1. BDR Transmitter Output Power 1) Target power (class2) -6 2.0 +4 dBm 2. BDR Initial Carrier Freq. Tolerance -75 -1.3 +75 KHz 3. BDR Carrier Drift 1) Drift Rate/50us -20 4.7 +20 KHz 2) Average Drift -25 -1 +25 dB dB -40 +2 +40 KHz KHz -40 0 +40 KHz KHz 4. BDR Modulation Characteristic 1) F1avg(kHz) 140 162.1 175 KHz 2) F2avg(kHz) 115 146.5 - KHz 3 F1/F2 Ratio 0.8 0.9 - - 5 EDR Carrier Frequency Stability and Modulation Accuracy 1) Initial Frequency Error -75 -1.3 +75 KHz 2) Frequency Error -10 0.6 +10 KHz 3) Block Frequency Error -75 -1.2 +75 KHz 4 RMS DEVM @2Mbps 0.2 0.045 - 5 Peak DEVM @2Mbps 0.35 0.1 - 6 99% DEVM @% Symbols <= 0.3 (2Mbps) 99% 100% - 7 RMS DEVM @3Mbps 0.13 0.037 - 8 Peak DEVM @3Mbps 0.25 0.08 - 9 99% DEVM @% Symbols <= 0.2(3Mbps) 99% 100% - RX Characteristics Unit 6. Minimum Input Level Sensitivity 1) BDR Single slot sensitivity (BER 0.1%) -70 dBm 2) BDR Multi slot sensitivity (BER 0.1%) -70 dBm 3) EDR sensitivity@2Mbps (BER 0.01%) -70 dBm 4) EDR sensitivity@3Mbps (BER 0.01%) -70 dBm 7. Maximum Input Level (BER 0.1%) -20 dBm
COMPANY CONFIDENTIAL 14 6. Appendix Appendix A - Label Information
COMPANY CONFIDENTIAL 15 Appendix B - Package Information
COMPANY CONFIDENTIAL Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: N89-NU260HS”. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

Navigation menu