D Link BA1210PA1 Business Cloud Wave 2 Access Point User Manual DBA 1210P A1 Manual 20170304

D Link Corporation Business Cloud Wave 2 Access Point DBA 1210P A1 Manual 20170304

User Manual_rev.pdf

Business Cloud Wave 2 Access PointDBA-1210PUser ManualVersion 1.00 | 06/12/2016
2D-Link DBA-1210P User ManualTable of ContentsPackage Contents.........................................................................3System Requirements................................................................. 4Introduction ................................................................................... 5Features............................................................................................ 6Hardware Overview..................................................................... 7LEDs ........................................................................................... 7Bottom...................................................................................... 8Dynamic and Static IP Addressing on the AP .................. 9Powering the Device........................................................10Congure the Device.......................................................11Web-based Conguration Utility..........................................13Access Point Status ............................................................14Access Point Local Settings.............................................15Device CLI Conguration.........................................................17Access Point Status ............................................................17Access Point Local Settings.............................................18Mounting the Device.......................................................19Technical Specications..................................................22Conguring MAC Authentication on the RADIUS Server23Table of Contents
3D-Link DBA-1210P User ManualSection 1 - Product Overview*Ceiling Bracket is an optional accessory and not included in the package. If it is required, please contact your reseller to order it.Note: Using a power supply with a dierent voltage rating or PoE injector than the one included with the DBA-1210P will cause damage and void the warranty for this product.Package ContentsDBA-1210P Business Cloud Wave 2 Access PointMounting RingPower AdapterCeiling Bracket*Ethernet Cable
4D-Link DBA-1210P User ManualSection 1 - Produc t OverviewSystem RequirementsNetwork Requirements• An Ethernet-based Network• IEEE 802.11a/b/g/n/ac wireless clients (AP Mode)• IEEE 802.11a/b/g/n/ac wireless network (AP Mode)Web-based Conguration Utility RequirementsComputer with the following:• Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapterBrowser Requirements:• Internet Explorer® 10 and higher• Mozilla Firefox 36.0 and higher• Google™ Chrome v41.0.2272.104 and higher• Apple Safari v6.2.7 and higherSerial, Ethernet Connection, or Wireless connection to the Access Point• The computer used to manually congure the access point must be connected to the access point by a serial cable, Ethernet cable, or wireless connection.Additional DocumentationThe following documentation provides additional information about DBA-1210P installation and management:• The Quick Installation Guide provides the information about package content and device installation.• The D-Link Business Cloud User Manual provides the guidance about device management through the D-Link Business Cloud
5D-Link DBA-1210P User ManualSection 1 - Product OverviewIntroductionThe D-Link DBA-1210P Business Cloud Wave 2 Access Point provides continuous, high-speed access between wireless devices and Ethernet devices. It is an advanced, standards-based solution for wireless networking in businesses of any size. The DBA-1210P enables wireless local area network (WLAN) deployment while providing state-of-the-art wireless networking features.The DBA-1210P is managed through the D-Link Business Cloud, with an intuitive browser-based interface that enables rapid deployment. Since the DBA-1210P is self-conguring and managed over the web, it can even be deployed at a remote location without on-site IT sta.This document also describes how to perform the manual networking conguration of DBA-1210P in case of it not being able to connect to D-Link Business Cloud through the internet.Before you power on a new DBA-1210P, review the following sections to check required hardware and software components, client congurations, and compatibility issues. Make sure you have everything you need for a successful launch and test of your new or extended wireless network.
6D-Link DBA-1210P User ManualSection 1 - Product Overview• Automatic Self Conguration - The DBA-1210P will automatically connect to the D-Link Business Cloud to perform its self-conguration and management, meaning it can even be deployed at a remote location without an on-site network administrator. The D-Link Business Cloud also helps to manage the deployment of new features, bug xes, and enhancements, which are automatically pushed to the DBA-1210P.• Faster Wireless Networking - The DBA-1210P provides an up to 1.75 Gbps1 wireless connection with other 802.11ac wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with IEEE802.11a/b/g/n/ac Devices - The DBA-1210P is still fully compatible with the 802.11a/b/g/n/ac standards, so it can connect with any existing 802.11a/b/g/n/ac wireless adapters.• Dual Band Wireless Radio - The DBA-1210P comes equipped both 2.4 Ghz and 5 Ghz high powered internal radios that help to provide better wireless coverage and increased signal strength.• PoE Enabled - The DBA-1210P supports PoE (Power over Ethernet) which enables it to be supplied with Ethernet over a power cable.• Convenient Installation - The DBA-1210P features a wall/ceiling mount for easy deployment in a variety of locations.• Streamlined Design - The DBA-1210P is designed with a slim form factor that easily blends into any oce environment1Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range. Features
7D-Link DBA-1210P User ManualSection 1 - Product OverviewHardware OverviewLEDs1CloudSolid Orange The DBA-1210P is connecting to the D-Link Business CloudSolid Green The DBA-1210P is currently in Cloud modeSolid Red The DBA-1210P is not working properly in Cloud mode1
8D-Link DBA-1210P User ManualSection 1 - Product OverviewHardware OverviewBottom1 Power Receptor Connects to the power adapter.2 LAN Port (PoE)Power is supplied through the LAN cable connected in this port via the Power over Ethernet Injector. Please see “Installation” on page <?> for more details on how to correctly power the DBA-1210P and connect to other networking devices.3 Reset ButtonPress the Reset Button between 2 to 5 seconds to restart the device.Press the Reset Button between 6 to 15 seconds to restore the device to its factorydefault settings.Press the Reset Button more than 15 seconds to restore the device to its factory defaultsettings and also force the loading of alternate rmware.4Kensington Security Slot Allows the device to be secured with any Kensington Security Lock.1423
9D-Link DBA-1210P User ManualSection 2 - InstallationDynamic and Static IP Addressing on the APWhen you power on the access point, the built-in DHCP client searches for a DHCP server on the network in order to obtain an IP Address and other network information. If the AP is not able to be assigned a DHCP IP on the network, you can manually recongure the static IP address and relevant network setting through device Administration Web UI or CLI interface.To manually congure network setting through device Administration Web UI, please refer to “Web-based Conguration Utility” on page 13You can manually congure network setting through device CLI as well by any of the following methods:• Serial Port Connection to the AP • Telnet Connection to the AP • SSH Connection to the APPlease refer to “Device CLI Conguration” on page 17 for more information on how to congure the DBA-1210P using the CLI.Caution! If you do not have a DHCP server on your internal network, and do not plan to use one, the rst thing you must do after powering on the access point is to change the connection type from DHCP to static IP and assign a new static IP address to the AP.Caution! The default login information is admin/admin for both the Web UI and CLI. Please note that the credentials might have been changed through the D-Link Business Cloud.
10D-Link DBA-1210P User ManualSection 2 - InstallationTo power on the DBA-1210P, you can use one of the two following methods:1. Connect the supplied power adapter2. Plug one end of your Ethernet cable into the LAN port of the DBA-1210P, and the other end into a port on a Power over Ethernet enabled switch.Powering the Device
11D-Link DBA-1210P User ManualSection 3 - CongurationThe easiest way to congure the DBA-1210P is to connect the DBA-1210P to the Internet through a switch or router. Connect your computer to the Internet and manage the DBA-1210P via D-Link Business Cloud. The DBA-1210P will automatically connect to the D-Link Business Cloud, download its conguration, and join the appropriate network.If you are unable to connect the DBA-1210P to the D-Link Business Cloud through the Internet due to your networking configuration you will need to manually configure the DBA-1210P using one of the following options.Congure the DeviceSwitch or RouterSwitch or Router ManagementDBA-1210PD-Link Business CloudDBA-1210P Management1. Connect the DBA-1210P and your computer directly via a straight-through Ethernet cable. You can then manage the access point from your computer using the following steps.Enter the DBA-1210P hostname in the address eld of your browser and then press Enter. The default hostname is “DBA-1210P-XXXX” where XXXX is the last 4 digits of the MAC address listed on the device label located on the bottom of the device.Log in to the administration web pages. The default login information is:Username: adminPassword: admin
12D-Link DBA-1210P User ManualSection 3 - Conguration2. Connect the DBA-1210P and your computer to the same switch or router. You can then manage the access point from your computer using the following stepsEnter the DBA-1210P hostname in the address eld of your browser and then press Enter. The default hostname is “DBA-1210P-XXXX” where XXXX is the last 4 digits of the MAC address listed on the device label located on the bottom of the device.Log in to the administration web pages. The default login information is:Username: adminPassword: admin3. Connect your computer to the DBA-1210P wirelessly via the SSID “DBA-1210P-XXXX” where XXXX is the last 4 digits of the MAC address listed on the device label located on the bottom of the device. You can then manage the access point from your computer using the following steps.Enter the DBA-1210P hostname in the address eld of your browser and then press Enter. The default hostname is “DBA-1210P-XXXX” where XXXX is the last 4 digits of the MAC address listed on the device label located on the bottom of the device.Log in to the administration web pages. The default login information is:Username: adminPassword: adminSwitch or Router ManagementDBA-1210PDBA-1210P Management
13D-Link DBA-1210P User ManualSection 3 - CongurationThis section will show you how to congure your new D-Link Business Cloud Wave 2 Access Point using the web-based conguration utility.Web-based Conguration UtilityIf you wish to change local settings for the DBA-1210P, you may use the web-based conguration utility.To access the conguration utility, open a web browser such as Internet Explorer and enter the DBA-1210P hostname in the address eld of your browser and then press Enter. The default hostname is “DBA-1210P-XXXX” where XXXX is the last 4 digits of the MAC address listed on the device label located on the bottom of the device.Enter admin into the User Name eld and then enter admininto the Password eld.
14D-Link DBA-1210P User ManualSection 3 - CongurationAccess Point StatusFrom the Status page, you can view various information about the DBA-1210P, including network status, Cloud connection status, and device information. The following table describes the elds and conguration options on the Status page.Device name.Ethernet MAC (ex. ethaddr=C0:A0:BB:6E:0A:B3)Serial NumberCurrent running rmware versionThe ID for D-Link Business Cloud Registration.Ethernet IP addressThe status of cloud registration. Yes/No.The Date of registration. Ex. 2013/3/11Local network status.Internet connection status.D-Link Business Cloud connection status.Name:Mac Address:Serial Number:Current Firmware:Device UID:IP Address to Cloud:Cloud Registration:Date of Registration:Local Network:Internet Connection:D-Link BusinessCloud:
15D-Link DBA-1210P User ManualSection 3 - CongurationAccess Point Local SettingsIf you select DHCP, the UAP acquires its IP address, subnet mask, DNS, and gateway information from a DHCP server.If you select Static IP, you must enter information in the Static IP Address, Subnet Mask, and Default Gateway elds.Select the mode for the DNS.In Dynamic mode, the IP addresses for the DNS servers are assigned automatically via DHCP. This option is only available if you specied DHCP for the Connection Type. In Manual mode, you must assign static IP addresses to resolve domain names.The management VLAN is the VLAN associated with the IP address you use to access the AP. The default management VLAN ID is 1.Provide a number between 1 and 4094 for the management VLAN ID.To enable VLAN, select the Enable VLAN check box.To disable VLAN , clear the Enable VLAN check box.Connection Type:DNSNameservers:Management VLAN ID:Enable VLAN:From the Local Settings page, you can manually congure the network settings to fulll various network environments.
16D-Link DBA-1210P User ManualSection 3 - CongurationTo enable VLAN tagging, select Tagged.To enable VLAN untagged, select Untagged.To enable IPv6 function, select Enabled.To disable IPv6 function, select Disabled.If you know the path to the new firmware image le, enter it in the Image Filename eld. Otherwise, click the Browse button and locate the rmware image le.Click Upgrade to apply the new rmware image.Upon clicking Upgrade for the rmware upgrade, a popup conrmation window is displayed that describes the upgrade process.Click OK to conrm the upgrade and start the process.To enable proxy settings, select Enabled.To disable proxy settings, select Disabled.Proxy IPv4 address or URL.Proxy port number. VLAN Mode:Enable IPv6:Firmware Upgrade:Enable Proxy:Host:Port:
17D-Link DBA-1210P User ManualSection 3 - CongurationDevice CLI CongurationAccess Point StatusYou can view various information by using the following CLI commands, including network status, Cloud connection status, and device information. All of the parameters need the command apply to take eect. Use the following steps to log into the CLI:1. Connect the console cable to the console port of the device and the USB to RS-232 cable.2. Connect the USB to RS-232 cable to the serial port of a PC, Apple, or UNIX workstation, start a terminal-emulation program, such as HyperTerminal or TeraTerm.3. Congure the terminal-emulation program to use the following settings:• Baud rate: 115200 bps• Data bits: 8• Parity: none• Stop bit: 1• Flow control: none4. The login name is admin. The default password is admin. After a successful login, the screen shows the “CLOUD_CLI>>”.Action CommandsView the system information get systemView the model name get system modelView the MAC get management macView the serial number. get system serial-numberView the rmware version. get system versionView the device UID get system device-uidView the Ethernet IP address get management ipView cloud registration get system cloud-registrationView date of registration get system date-of-registrationView local network status get system local-network-statusView internet status get system internet-statusView cloud connection status get system cloud-connect-status
18D-Link DBA-1210P User ManualSection 3 - CongurationYou can view various information by using the following CLI commands, including network status, Cloud connection status, and device information. All of the parameters need the command apply to take eect. Action CommandsGet Current Settings for the Ethernet (Wired) Internal Interface. get managementView the connection type. get management dhcp-statusUse DHCP as the connection type. set management dhcpUse a Static IP as the connection type, and then static IP address, subnet mask and default gateway. set management staticstatic-ip ip_address mask netmask gateway ip_addressView the DNS name server mode. get host dns-via-dhcpSet DNS Name servers to use static IP addresses. set host static-dns-1 ip_addressorset host static-dns-1 ip_address static-dns-2 ip_addressSet DNS name servers to use DHCP IP addressing (Manual to Dynamic Mode). set host dns-via-dhcp {up | down}View VLAN information. get management vlan-idget management vlan-enableget management vlan-modeEnable/Disable the VLAN tagging. set management vlan-enable {up | down}Set the VLAN ID. set management vlan-id valueEnable/Disable the VLAN mode. set management vlan-mode {tagged | untagged}View IPv6 information. get management ipv6-enableEnable/Disable IPv6 function. set management ipv6-enable {up | down}Upgrade the device rmware. rmware-upgrade urlView Proxy information. get management proxy-enableget management proxy-hostget management proxy-portEnable/Disable Proxy server. set management proxy-enable {up | down}Set IP address or domain name of proxy server. set management proxy-host ip_addressset management proxy-host domain_nameSet port number of proxy server. set management proxy-port portApply the conguration. applyExit command line. exitReboot the system. rebootAccess Point Local Settings
19D-Link DBA-1210P User ManualSection 4 - MountingMounting the DeviceThis section will show you how to congure your new D-Link Business Cloud Wave 2 Access Point using the web-based conguration utility.To mount the DBA-1210P, use one of the following methods:Solid wall or ceiling Installation1. Place the mounting bracket on a wall or ceiling.2. Mark the points where you will insert the screws. Take out the mounting ring.3. Drill holes in the marked points and insert the plastic wall anchors.
20D-Link DBA-1210P User ManualSection 4 - Mounting4. Use the supplied screws to attach the mounting ring to the wall.5. Plug the Ethernet cable into the LAN port on the access point.6. To attach the access point to the mounting bracket.
21D-Link DBA-1210P User ManualSection 4 - MountingCeiling bracketCeiling crossbarMounting with a ceiling bracket Installation1. Clip two ceiling brackets onto the ceiling panels. Make sure both brackets are in line with each other.2. Use the provided screws to attach the mounting ring to the ceiling bracket.3. Plug the Ethernet cable into the LAN port on the access point.4. Place the DBA-1210P’s male bracket in the mounting bracket’s female bracket. Click DBA-1210P and the mounting racket to lock in position.Placement on a Desktop1. Plug the Ethernet cable into the LAN port on the access point.2. If you are not using a PoE switch or router with the DBA-1510P, plug the power cable into the Power Receptor on the access point.
22D-Link DBA-1210P User ManualAppendix A - Technical SpecicationsTechnical Specications1Range will vary depending on country’s maximum transmit power output regulation. Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range.GeneralDevice Interfaces • 802.11a/b/g/n/ac wireless• Reset button• One 10/100/1000 Ethernet port (supports PoE)• DC Power ConnectorLED • CloudAntenna • Internal Omni-Directional Antenna • 2x2 MIMO with two spatial streamsWireless Frequency • 2.4 GHz • 5 GhzFunctionalitySecurity • WPA2-Personal/Enterprise• WPA-Personal/Enterprise• 802.1X• MAC Address Filtering• Rogue AP Detection• Station Isolation• SSID Isolation• Guest Access• Captive Portal• IP FilterSSID • Support for up to 16 SSIDsPhysicalDimensions • 170x170x33.5mm (6.69x6.69x1.32 inches)Weight • Without Mount: 314.2 grams (0.69 lbs) • With Mount: 370.6 grams (0.82 lbs)Power • Power over Ethernet (PoE): 802.3af Power over Ethernet • AC Input: 100 to 240 V, 50/60 Hz; Output: DC 12 V / 2 APower Consumption • 12W (PoE) • 12W (Adapter)Temperature • Operating: 0 to 40 °C (32 to 104 °F) • Storage: -20 to 65 (-4 to 149)Humidity • Operating: 10% to 90% non-condensing • Storage: 5% to 95% non-condensingRegulatory • CE• RoHS• REACH• WEEESecurity • Kensington lock slot • Security screwMounting Options • Ceiling mount• Wall mount• Desktop (Horizontal)
23D-Link DBA-1210P User ManualAppendix B - Conguring MAC Authentication on the RADIUS ServerConfiguring MAC Authentication on the RADIUS ServerIf you use RADIUS MAC authentication for MAC-based access control, you must congure a station list on the RADIUS server. The station list contains client MAC address entries, and the format for the list is described in the following table. RADIUS Server Attribute Description ValueUser-Name MAC address of the client station. Valid Ethernet MAC Address.User-Password A xed global password used to lookup a client MAC entry. DBA-1210P
&ĞĚĞƌĂůŽŵŵƵŶŝĐĂƚŝŽŶŽŵŵŝƐƐŝŽŶ/ŶƚĞƌĨĞƌĞŶĐĞ^ƚĂƚĞŵĞŶƚdŚŝƐĚĞǀŝĐĞĐŽŵƉůŝĞƐǁŝƚŚWĂƌƚϭϱŽĨƚŚĞ&ZƵůĞƐ͘KƉĞƌĂƚŝŽŶŝƐƐƵďũĞĐƚƚŽƚŚĞĨŽůůŽǁŝŶŐƚǁŽĐŽŶĚŝƚŝŽŶƐ͗ ;ϭͿdŚŝƐĚĞǀŝĐĞŵĂLJŶŽƚĐĂƵƐĞŚĂƌŵĨƵůŝŶƚĞƌĨĞƌĞŶĐĞ͕ĂŶĚ ;ϮͿƚŚŝƐĚĞǀŝĐĞŵƵƐƚĂĐĐĞƉƚĂŶLJŝŶƚĞƌĨĞƌĞŶĐĞƌĞĐĞŝǀĞĚ͕ŝŶĐůƵĚŝŶŐŝŶƚĞƌĨĞƌĞŶĐĞƚŚĂƚŵĂLJĐĂƵƐĞƵŶĚĞƐŝƌĞĚŽƉĞƌĂƚŝŽŶ͘dŚŝƐ ĞƋƵŝƉŵĞŶƚ ŚĂƐ ďĞĞŶ ƚĞƐƚĞĚ ĂŶĚ ĨŽƵŶĚ ƚŽ ĐŽŵƉůLJ ǁŝƚŚ ƚŚĞ ůŝŵŝƚƐ ĨŽƌ Ă ůĂƐƐ  ĚŝŐŝƚĂůĚĞǀŝĐĞ͕ ƉƵƌƐƵĂŶƚ ƚŽ WĂƌƚ ϭϱ ŽĨ ƚŚĞ & ZƵůĞƐ͘  dŚĞƐĞ ůŝŵŝƚƐ ĂƌĞ ĚĞƐŝŐŶĞĚ ƚŽ ƉƌŽǀŝĚĞƌĞĂƐŽŶĂďůĞ ƉƌŽƚĞĐƚŝŽŶ ĂŐĂŝŶƐƚ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ŝŶ Ă ƌĞƐŝĚĞŶƚŝĂů ŝŶƐƚĂůůĂƚŝŽŶ͘ dŚŝƐĞƋƵŝƉŵĞŶƚŐĞŶĞƌĂƚĞƐ͕ƵƐĞƐĂŶĚĐĂŶƌĂĚŝĂƚĞƌĂĚŝŽĨƌĞƋƵĞŶĐLJĞŶĞƌŐLJĂŶĚ͕ŝĨŶŽƚŝŶƐƚĂůůĞĚĂŶĚƵƐĞĚ ŝŶ ĂĐĐŽƌĚĂŶĐĞ ǁŝƚŚ ƚŚĞ ŝŶƐƚƌƵĐƚŝŽŶƐ͕ ŵĂLJ ĐĂƵƐĞ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ƚŽ ƌĂĚŝŽĐŽŵŵƵŶŝĐĂƚŝŽŶƐ͘  ,ŽǁĞǀĞƌ͕ ƚŚĞƌĞ ŝƐ ŶŽ ŐƵĂƌĂŶƚĞĞ ƚŚĂƚ ŝŶƚĞƌĨĞƌĞŶĐĞ ǁŝůů ŶŽƚ ŽĐĐƵƌ ŝŶ ĂƉĂƌƚŝĐƵůĂƌ ŝŶƐƚĂůůĂƚŝŽŶ͘  /Ĩ ƚŚŝƐ ĞƋƵŝƉŵĞŶƚ ĚŽĞƐ ĐĂƵƐĞ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ƚŽ ƌĂĚŝŽ ŽƌƚĞůĞǀŝƐŝŽŶƌĞĐĞƉƚŝŽŶ͕ǁŚŝĐŚĐĂŶďĞĚĞƚĞƌŵŝŶĞĚďLJƚƵƌŶŝŶŐƚŚĞĞƋƵŝƉŵĞŶƚŽĨĨĂŶĚŽŶ͕ƚŚĞƵƐĞƌŝƐĞŶĐŽƵƌĂŐĞĚƚŽƚƌLJƚŽĐŽƌƌĞĐƚƚŚĞŝŶƚĞƌĨĞƌĞŶĐĞďLJŽŶĞŽĨƚŚĞĨŽůůŽǁŝŶŐŵĞĂƐƵƌĞƐ͗Ͳ ZĞŽƌŝĞŶƚŽƌƌĞůŽĐĂƚĞƚŚĞƌĞĐĞŝǀŝŶŐĂŶƚĞŶŶĂ͘Ͳ /ŶĐƌĞĂƐĞƚŚĞƐĞƉĂƌĂƚŝŽŶďĞƚǁĞĞŶƚŚĞĞƋƵŝƉŵĞŶƚĂŶĚƌĞĐĞŝǀĞƌ͘Ͳ ŽŶŶĞĐƚƚŚĞĞƋƵŝƉŵĞŶƚŝŶƚŽĂŶŽƵƚůĞƚŽŶĂĐŝƌĐƵŝƚĚŝĨĨĞƌĞŶƚĨƌŽŵƚŚĂƚƚŽǁŚŝĐŚƚŚĞƌĞĐĞŝǀĞƌŝƐĐŽŶŶĞĐƚĞĚ͘Ͳ ŽŶƐƵůƚƚŚĞĚĞĂůĞƌŽƌĂŶĞdžƉĞƌŝĞŶĐĞĚƌĂĚŝŽͬdsƚĞĐŚŶŝĐŝĂŶĨŽƌŚĞůƉ͘&ĂƵƚŝŽŶ͗ŶLJĐŚĂŶŐĞƐŽƌŵŽĚŝĨŝĐĂƚŝŽŶƐŶŽƚĞdžƉƌĞƐƐůLJĂƉƉƌŽǀĞĚďLJƚŚĞƉĂƌƚLJƌĞƐƉŽŶƐŝďůĞĨŽƌĐŽŵƉůŝĂŶĐĞĐŽƵůĚǀŽŝĚƚŚĞƵƐĞƌΖƐĂƵƚŚŽƌŝƚLJƚŽŽƉĞƌĂƚĞƚŚŝƐĞƋƵŝƉŵĞŶƚ͘dŚŝƐƚƌĂŶƐŵŝƚƚĞƌŵƵƐƚŶŽƚďĞĐŽͲůŽĐĂƚĞĚŽƌŽƉĞƌĂƚŝŶŐŝŶĐŽŶũƵŶĐƚŝŽŶǁŝƚŚĂŶLJŽƚŚĞƌĂŶƚĞŶŶĂŽƌƚƌĂŶƐŵŝƚƚĞƌ͘&Žƌ ŽƉĞƌĂƚŝŽŶ ǁŝƚŚŝŶ ϱ͘ϭϱ Ε ϱ͘Ϯϱ',nj ͬ ϱ͘ϰϳ Εϱ͘ϳϮϱ',nj ĨƌĞƋƵĞŶĐLJ ƌĂŶŐĞ͕ ŝƚ ŝƐ ƌĞƐƚƌŝĐƚĞĚ ƚŽŝŶĚŽŽƌĞŶǀŝƌŽŶŵĞŶƚ͘ dŚĞďĂŶĚĨƌŽŵϱϲϬϬͲϱϲϱϬD,njǁŝůůďĞĚŝƐĂďůĞĚďLJƚŚĞƐŽĨƚǁĂƌĞĚƵƌŝŶŐƚŚĞŵĂŶƵĨĂĐƚƵƌŝŶŐĂŶĚĐĂŶŶŽƚďĞĐŚĂŶŐĞĚďLJƚŚĞĞŶĚƵƐĞƌ͘dŚŝƐĚĞǀŝĐĞŵĞĞƚƐĂůůƚŚĞŽƚŚĞƌƌĞƋƵŝƌĞŵĞŶƚƐƐƉĞĐŝĨŝĞĚŝŶWĂƌƚϭϱ͕^ĞĐƚŝŽŶϭϱ͘ϰϬϳŽĨƚŚĞ&ZƵůĞƐ͘dŚŝƐ ĞƋƵŝƉŵĞŶƚ ĐŽŵƉůŝĞƐ ǁŝƚŚ & ƌĂĚŝĂƚŝŽŶ ĞdžƉŽƐƵƌĞ ůŝŵŝƚƐ ƐĞƚ ĨŽƌƚŚ ĨŽƌ ĂŶ ƵŶĐŽŶƚƌŽůůĞĚĞŶǀŝƌŽŶŵĞŶƚ͘dŚŝƐĞƋƵŝƉŵĞŶƚƐŚŽƵůĚďĞŝŶƐƚĂůůĞĚĂŶĚŽƉĞƌĂƚĞĚǁŝƚŚŵŝŶŝŵƵŵĚŝƐƚĂŶĐĞϮϮĐŵďĞƚǁĞĞŶƚŚĞƌĂĚŝĂƚŽƌΘLJŽƵƌďŽĚLJ͘

Navigation menu