D Link DI624MA1 802.11g WLAN Mini-PCI Module User Manual 1

D Link Corporation 802.11g WLAN Mini-PCI Module 1

Contents

User Manual 1 of 2 for Access Poiint

2DI-624M User’s Manual D-Link Systems, Inc.Table of ContentsTable of ContentsPackage Contents ............................................................................... 4Minimum System Requirements .............................................................. 4Introduction ...................................................................................... 5Features and Benefits .......................................................................... 6Hardware Overview ............................................................................. 7Connections .........................................................................................................7LEDs .....................................................................................................................8Wireless Basics ................................................................................. 9Standards-Based Technology .............................................................................10Installation Considerations .................................................................................10Getting Started .................................................................................. 11Using the Configuration Menu ................................................................ 12Home .................................................................................................................13Wizard ..........................................................................................................13Wireless ........................................................................................................14WAN .............................................................................................................15Dynamic IP Address ................................................................................15Static IP Address .....................................................................................16PPPoE .....................................................................................................18LAN ...............................................................................................................20DHCP ............................................................................................................21Advanced ...........................................................................................................22Virtual Server ................................................................................................22Applications ..................................................................................................24Filters ............................................................................................................26IP Filters ..................................................................................................26MAC Filters ..............................................................................................27Parental Control ............................................................................................28URL Blocking ..........................................................................................28Domain Blocking .....................................................................................29Firewall .........................................................................................................30DMZ ..............................................................................................................31Performance .................................................................................................32Tools ..................................................................................................................34Admin ...........................................................................................................34Time ..............................................................................................................36
3DI-624M User’s Manual D-Link Systems, Inc.Table of ContentsSystem .........................................................................................................37Firmware .......................................................................................................38Misc. .............................................................................................................39Tools ..................................................................................................................41Device Info ....................................................................................................41Log ...............................................................................................................43Log Settings ............................................................................................44Stats .............................................................................................................45Wireless ........................................................................................................45Networking Basics ............................................................................. 46Naming Your Computer ......................................................................................53Checking the IP Address in Windows XP ...........................................................54Assigning a Static IP Address in Windows XP/2000 ..........................................56Assigning a Static IP Address in Macintosh OSX ...............................................58Checking the Wireless Connection by Pinging in Windows XP and 2000 ...........61Checking the Wireless Connection by Pinging in Windows Me and 98 ..............62Troubleshooting ................................................................................ 63Technical Specifications ...................................................................... 69Frequently Asked Questions .................................................................. 72Appendix ....................................................................................... 106Securing Your Network ...................................................................................106Glossary ...........................................................................................................107Contacting Technical Support .............................................................. 115Warranty ...................................................................................... 116Registration ................................................................................... 120
4DI-624M User’s Manual D-Link Systems, Inc.Package ContentsPackage Contentsn D-Link DI-624M Super G Smart Antenna Wireless Routern CAT-5 Ethernet Cable (All the DI-624M’s Ethernet ports are Auto-MDIX) n Power Adapter (5.0V, 2.5A)n Vertical Standsn Mounting Kitn CD-ROM with Software and Manualn Quick Installation GuideNote: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product.If any of the above items are missing, please contact your reseller.Minimum System Requirementsn Ethernet-Based Cable or DSL Modemn Computers with Windows, Macintosh, or Linux-based operating systems with an installed Ethernet adapter and CD-ROM Driven Internet Explorer Version 6.0 or Netscape Navigator Version 7.0 and Above
5DI-624M User’s Manual D-Link Systems, Inc.IntroductionIntroductionThe D-Link DI-624M Super G Smart Antenna Wireless Router is an 802.11g high-performance, wireless router that supports high-speed wireless networking at home, at work or in public places. Unlike most routers, the DI-624M provides data transfers at up to 108 Mbps (compared to the standard 54 Mbps) when used with other D-Link Super G Smart Antenna products. The 802.11g standard is backwards compatible with 802.11b products. This means that you do not need to change your entire network to maintain connectivity. You may sacrifice some of 802.11g’s speed when you mix 802.11b and 802.11g devices, but you will not lose the ability to communicate when you incorporate the 802.11g standard into your 802.11b network. You may choose to slowly change your network by gradually replacing the 802.11b devices with 802.11g devices .In addition to offering faster data transfer speeds when used with other 802.11g products, the DI-624M has the newest, strongest, most advanced security features available today. When used with other 802.11g WPA (WiFi Protected Access) compatible products in a network, the security features include:WPA: Wi-Fi Protected Access authorizes and identifies users based on a secret key that changes automatically at a regular interval. WPA uses TKIP (Temporal Key Integrity Protocol) to change the temporal key every 10,000 packets (a packet is a kind of message transmitted over a network.) This insures much greater security than the standard WEP security. (By contrast, the older WEP encryption required the keys to be changed manually.)
6DI-624M User’s Manual D-Link Systems, Inc.Features and BenefitsFeatures and Benefitsn Fully compatible with the 802.11g standard to provide a wireless data rate of up to 108Mbpsn Backwards compatible with the 802.11b standard to provide a wireless data rate of up to 11Mbpsn WPA (Wi Fi Protected Access) authorizes and identifies users based on a secret key that changes automatically at a regular interval, for example: Pre Shared Key mode means that the home user, without a RADIUS server, will obtain a new security key every time the he or she connects to the network, vastly improving the safety of communications on the networkn Utilizes OFDM technology (Orthogonal Frequency Division Multiplexing)n User-friendly configuration and diagnostic utilitiesn Operates in the 2.4GHz frequency rangen Connects multiple computers to a Broadband (Cable or DSL) modem to share the Internet connectionn Advanced Firewall features: Supports NAT with VPN pass-through, providing added security, MAC Filtering, IP Filtering, URL Filtering, Domain Blocking, and Schedulingn DHCP server enables all networked computers to automatically receive IP addressesn Web-based interface for Managing and Configuringn Access Control to manage users on the networkn Supports special applications that require multiple connectionsn Equipped with 4 10/100 Ethernet ports, 1 WAN port, Auto MDI/MDIX
7DI-624M User’s Manual D-Link Systems, Inc.Hardware OverviewHardware OverviewConnectionsDC Power ConnectorThe DC power input connector is labeled DC 5V with a single jack socket to supply power to the DI-624M.All Ethernet Ports (WAN and LAN) are auto MDI/MDIX, meaning you can use either a straight-through or a crossover Ethernet cable.Auto MDI/MDIX WAN PortThis is the connection for the Ethernet cable to the Cable or DSL modemAuto MDI/MDIX LAN Ports These ports automatically sense the cable type when connecting to Ethernet-enabled computers.Reset ButtonPressing the reset button restores the router to its original factory default settings.
8DI-624M User’s Manual D-Link Systems, Inc.Hardware OverviewLEDsWLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission.WAN LED A solid light indicates connection on the WAN port. This LED blinks during data transmission.LOCAL NETWORK LED A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission.STATUSA blinking light indicates that the DI-624M is ready.POWER LED A solid light indicates a proper connection to the power supply.
9DI-624M User’s Manual D-Link Systems, Inc.Wireless BasicsWireless BasicsD-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. D-Link wireless products will allow you access to the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking brings.A WLAN is a cellular computer network that transmits and receives data with radio signals instead of wires. WLANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. People use wireless LAN technology for many different purposes:Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency.Low Implementation Costs – WLANs are easy to set up, manage, change and relocate. Networks that frequently change can benefit from WLANs ease of implementation. WLANs can operate in locations where installation of wiring may be impractical.Installation and Network Expansion - Installing a WLAN system can be fast and easy and can eliminate the need to pull cable through walls and ceilings. Wireless technology allows the network to go where wires cannot go - even outside the home or office.Scalability – WLANs can be configured in a variety of topologies to meet the needs of specific applications and installations. Configurations are easily changed and range from peer-to-peer networks suitable for a small number of users to larger infrastructure networks to accommodate hundreds or thousands of users, depending on the number of wireless devices deployed.Inexpensive Solution - Wireless network devices are as competitively priced as conventional Ethernet network devices.
10DI-624M User’s Manual D-Link Systems, Inc.Wireless BasicsInstallation Considerations The D-Link DI-624MSuper G Smart Antenna Wireless Router lets you access your network, using a wireless connection, from virtually anywhere within its operating range. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:1 Keep the number of walls and ceilings between the DI-624M and other network devices to a minimum - each wall or ceiling can reduce your D-Link wireless product’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.2 Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.3 Building Materials can impede the wireless signal - a solid metal door or aluminum studs may have a negative effect on range. Try to position wireless devices and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials.4 Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate extreme RF noise.Standards-Based TechnologyThe DI-624M Super G Smart Antenna Wireless Router utilizes the 802.11g standard.The IEEE 802.11g standard is an extension of the 802.11b standard. It increases the data rate up to 54Mbps within the 2.4GHz band, utilizing OFDM technology.This means that in most environments, within the specified range of this device, you will be able to transfer large files quickly or even watch a movie in MPEG format over your network without noticeable delays. This technology works by transmitting high-speed digital data over a radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing) technology. OFDM works by splitting the radio signal into multiple smaller sub-signals that are then transmitted simultaneously at different frequencies to the receiver. OFDM reduces the amount of crosstalk (interference) in signal transmissions. The DI-624M is backwards compatible with 802.11b devices. This means that if you have an existing 802.11b network, the devices in that network will be compatible with
11DI-624M User’s Manual D-Link Systems, Inc.Getting StartedGetting Started Please remember that D-Link Super G Smart Antenna wireless devices are pre-configured to connect together, right out of the box, with their default settings. For a typical wireless setup at home, please do the following: You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office) Consult with your Cable or DSL provider for proper installation of the modem. Connect the Cable or DSL modem to the DI-624M Wireless Broadband Router (see the printed Quick Installation Guide included with your router). If you are connecting a desktop computer to your network, install the D-Link AirPlus Xtreme G DWL-G520 wireless PCI adapter into an available PCI slot on your desktop computer. You may also install the DWL-520+, or the DWL-520. (See the printed Quick Installation Guide included with the network adapter.) Install the D-Link DWL-G650M wireless Cardbus adapter into a laptop computer. (See the printed Quick Installation Guide included with the DWL-G650M.) Install the D-Link DFE-530TX+ adapter into a desktop computer. The four Ethernet LAN ports of the DI-624M are Auto MDI/MDIX and will work with both Straight-Through and Cross-Over cable. (See the printed Quick Installation Guide included with the DFE-530TX+.)
12DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuUsing the Configuration Menu Whenever you want to configure your DI-624M, you can access the Configuration Menu by opening the Web-browser and typing in the IP Address of the DI-624M. The DI-624M’s default IP Address is shown below: n Open the Web browser.n Type in the IP Address of the Router (http://192.168.0.1).Note: if you have changed the default IP Address assigned to the DI-624M, make sure to enter the correct IP Address.n Type admin in the User Name field.n Leave the Password blank.n Click OK.
13DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuWizardThe Home>Wizard screen will appear. Please refer to the Quick Installation Guide for more information regarding the Setup Wizard.These buttons appear on most of the configuration screens in this section. Please click on the appropriate button at the bottom of each screen after you have made a configuration change.HomeThe Advanced tab provides the following configuration options: Wizard, Wireless, WAN, LAN, and DHCP.Home > Wizard
14DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuWireless Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.6 is the default channel. All devices on the network must share the same channel. (Note: The wireless adapters will automatically scan and match the wireless setting.) Super G is a group of performance enhancement features that increase end user application throughput in an 802.11g network. Super G is backwarsd compatible to standard 802.11g devices. For top performance, all wirelss devices on the network should be Super G capable. Select either Disabled, Super G without Turbo, Super G with Dynamic Turbo, or Super G with Static Turbo.Standard 802.11g support, no enhanced capabilities.Home > Wireless
15DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuCapable of Packet Bursting, FastFrames, Compression, and no Turbo mode.Capable of Packet Bursting, FastFrames, Compression, and Dynamic Turbo. This setting is backwards compatible with non-Turbo (legacy) devices. Dynamic Turbo mode is only enabled when all nodes on the wireless network is Super G with Dynamic Turbo enabled.Capable of Packet Bursting, FastFrames, Compression, and Static Turbo. This setting is not backwards compatible with non-Turbo (legacy) devices. Static turbo mode is always on and is only enabled when all nodes on the wireless network is Super G with Static Turbo enabled.Select this mode to restrict your network to only those devices that employ the 802.11g standard. Enabling this mode will ensure that you maintain the highest connectivity rate, unhampered by any connection to an 802.11b device.Choose Enabled to broadcast the SSID across the network. All devices on a network must share the same SSID (Service Set Identifier) to establish communication. Choose Disabled if you do not wish to broadcast the SSID over the network.Select None, WEP, WPA, or WPA-PSK encryption.Select Open System or Shared Key authentication.Wired Equivalent Privacy (WEP) is a wireless security protocol for Wireless Local Area Networks (WLAN). WEP provides security by encrypting the data that is sent over the WLAN. Select Enabled or Disabled. Disabled is the default setting. (Note: If you enable encryption on the DI-624M make sure to also enable encryption on all the wireless clients or wireless connection will not be established.) Select the level of encryption desired: 64-bit, or 128-bit.Select HEX or ASCII. Input up to 4 WEP keys; select the one you wish to use.
16DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuWANDynamic IP AddressHome > WAN > Dynamic IP AddressChoose Dynamic IP Address to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services.The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed.The default MAC Address is set to the WAN’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.
17DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuThe default MAC address is set to the WAN’s physical interface MAC address on the Broadband Router. You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.Enter a DNS Address if you do not wish to use the one provided by your ISP.Enter an MTU value only if required by your ISP. Otherwise, leave it a the default setting.Static IP AddressHome > WAN > Static IP Address
18DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuChoose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.Input the public IP Address provided by your ISP.Input your Subnet mask. (All devices in the network must have the same subnet mask.)Input the public IP address of the ISP to which you are connecting.Input the primary DNS (Domain Name Server) IP address provided by your ISP. This is optional.Enter an MTU value only if required by your ISP. Otherwise, leave it at the default setting.
19DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuPPPoEHome > WAN > PPPoEPlease be sure to remove any existing PPPoE client software installed on your computers.Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoeE connection.
20DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuChoose this option if your ISP uses PPPoE. (Most DSL users will select this option.)Dynamic PPPoE: Receive an IP Address automatically from your ISP. Static PPPoE: You have an assigned (static) IP Address.Your PPPoE username provided by your ISP.Re-enter the PPPoE password.Enter the Service Name provided by your ISP (optional).This option is only available for Static PPPoE. Enter the static IP Address for the PPPoE connection.Primary DNS IP address provided by our ISP.This option is only available for Static PPPoE. Enter the static IP Address for the PPPoE connection.Maximum Transmission Unit-1492 is the default setting-you may need to change the MTU for optimal performance with your specific ISP.If enabled, the DI-624M will automatically connect to your ISP after your system is restarted or if the PPPoE connection is dropped.
21DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuLAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DI-624M. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.The IP address of the LAN interface. The default IP address is: 192.168.0.1.The subnet mask of the LAN interface. The default subnet mask is 255.255.255.0.This field is optional. Enter in the local domain name.LANHome > LAN
22DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuDHCP stands for Dynamic Host Control Protocol. The DI-624M has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DI-624M. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.Select Enabled or Disabled. The default setting is Enabled.The starting IP address for the DHCP server’s IP assignment.The ending IP address for the DHCP server’s IP assignment.The length of time for the IP lease. Enter the Lease time. The DHCPHome > DHCP
23DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuVirtual ServerThe DI-624M can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DI-624M firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DI-624M are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the DI-624M redirects the external service request to the appropriate server within the LAN network. The DI-624M is also capable of port-redirection meaning incoming traffic to a particular port may be redirected to a different port on the server computer.Each virtual service that is created will be listed at the bottom of the screen in the Virtual Servers List. There are pre-defined virtual services already in the table. You may use them by enabling them and assigning the server IP to use that particular virtual service.AdvancedThe Advanced tab provides the following configuration options: Virtual Server, Applications, Filters, Parental Control, Firewall, DMZ, and Performance.Advanced > Virtual Server
24DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration Menu Select Enabled or Disabled.Enter the name referencing the virtual service.The server computer in the LAN (Local Area Network) that will be providing the virtual services.The protocol used for the virtual service.The port number of the service used by the Private IP computer.The port number on the WAN (Wide Area Network) side that will be used to access the virtual service.The schedule of time when the virtual service will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. If it is set to Time, select the time frame for the service to be enabled. If the system time is outside of the scheduled time, the service will be disabled.If you have a Web server that you wanted Internet users to access at all times, you would need to enable it. Web (HTTP) server is on LAN (Local Area Network) computer 192.168.0.25. HTTP uses port 80, TCP. Name: Web Server Private IP: 192.168.0.25 Protocol Type: TCP Private Port: 80 Public Port: 80 Click on this icon to edit the virtual service.Click on this icon to delete the virtual service.
25DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuIf you have an FTP server that you wanted Internet users to access by WAN port 2100 and only during the weekends, you would need to enable it as such. FTP server is on LAN computer 192.168.0.30. FTP uses port 21, TCP. Name: FTP Server Private IP: 192.168.0.30 Protocol Type: TCP Private Port: 21 Public Port: 2100 Schedule: From: 01:00AM to 01:00AM, Sat to SunAll Internet users who want to access this FTP Server must connect to it from port 2100. This is an example of port redirection and can be useful in cases where there are many of the same servers on the LAN network.ApplicationsAdvanced > Applications
26DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuSome applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DI-624M. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic.The DI-624M provides some predefined applications in the table on the bottom of the web page. Select the application you want to use and enable it.Note: Only one PC can use each Special Application tunnel.This is the name referencing the special application.This is the port used to trigger the application. It can be either a single port or a range of ports. This is the protocol used to trigger the special application.This is the port number on the WAN side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. This is the protocol used to trigger the special application.
27DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuFiltersFilters are used to deny or allow LAN (Local Area Network) computers from accessing the Internet. The DI-624M can be setup to deny internal computers by their IP or MAC addresses. The DI-624M can also block users from accessing restricted Web sites.Use IP Filters to deny LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for the specific IP address.The IP address of the LAN computer that will be denied access to the Internet.The single port or port range that will be denied access to the Internet. Select the protocol type.This is the schedule of time when the IP Filter will be IP FiltersAdvanced > Filters > IP Filters
28DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuMAC FiltersUse MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.Select the filter you wish to use; in this case, MAC filters was chosen.Choose Disable MAC filters; allow MAC addresses listed below; or deny MAC addresses listed below. Enter the name here. Enter the MAC Address. Select a DHCP client from the pull-down list; click Clone to copy that MAC Address. Advanced > Filters > MAC Filters
29DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuURL Blocking is used to deny LAN computers from accessing specific web sites by the URL. A URL is a specially formatted text string that defines a location on the Internet. If any part of the URL contains the blocked word, the site will not be accessible and the web page will not display. To use this feature, enter the text string to be blocked and click Apply. The text to be blocked will appear in the list. To delete the text, just highlight it and click Delete.Select the filter you wish to use; in this case, URL Blocking was chosen. Select Enabled or Disabled. Block URLs which contain keywords listed below. Enter the keywords in this space. Parental ControlURL BlockingAdvanced > Parental Control > URL Blocking
30DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuDomain BlockingDomain Blocking is used to allow or deny LAN (Local Area Network) computers from accessing specific domains on the Internet. Domain blocking will deny all requests to a specific domain such as http and ftp. It can also allow computers to access specific sites and deny all other sites.Select the filter you wish to use; in this case, Domain Blocking was chosen. Disabled: Select Disabled to disable Domain Blocking. Allow: Allows users to access all domains except Blocked Domains. Deny: Denies users access to all domains except Permitted Domains.Enter the Permitted Domains in this field.Enter the Blocked Domains in this field.Advanced > Parental Control > Domain Blocking
31DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuFirewallFirewall Rules is an advanced feature used to deny or allow traffic from passing through the DI-624M. It works in the same way as IP Filters with additional settings. You can create more detailed access rules for the DI-624M. When virtual services are created and enabled, it will also display in Firewall Rules. Firewall Rules contain all network firewall rules pertaining to IP (Internet Protocol). In the Firewall Rules List at the bottom of the screen, the priorities of the rules are from top (highest priority) to bottom (lowest priority.)Note:The DI-624M MAC Address filtering rules have precedence over the Firewall Enable or disable the Firewall.Enter the name. Select Allow or Deny. Enter the IP Address range. Enter the IP Address range, the Protocol, and the Port Range.Advanced > Firewall
32DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuIf you have a client PC that cannot run Internet applications properly from behind the DI-624M, then you can set the client up for unrestricted Internet access. It allows a computer to be exposed to the Internet. This feature is useful for gaming purposes. Enter the IP address of the internal computer that will be the DMZ host. Adding a client to the DMZ (Demilitarized Zone) may expose your local network to a variety of security risks, so only use this option as a last resort.Enable or Disable the DMZ. The DMZ (Demilitarized Zone) allows a single computer to be exposed to the internet. By default the DMZ is disabled.Enter the IP Address of the computer to be in the DMZ.DMZAdvanced > DMZ
33DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuAuto is the default selection. Select from the drop down menu.100% is the default selection. Select from the drop down menu.Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. This value should remain at its default setting of 2432. If inconsistent data flow is a problem, only a minor modification should be made.The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before PerformanceAdvanced > PerformanceNote: These features will be available in future firmware releases.
34DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration Menu(Delivery Traffic Indication Message) 3 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages.Select Short or Long Preamble. The Preamble defines the length of the CRC block (Cyclic Redundancy Check is a common technique for detecting data transmission errors) for communication between the wireless router and the roaming wireless network adapters. Note: High network traffic areas should use the shorter preamble type.CTS (Clear To Send) is a function used to minimize collisions among wireless devices on a wireless local area network (LAN). CTS will make sure the wireless network is clear before a wireless client attempts to send wireless data. Enabling CTS will add overhead and may lower wireless throughput. None: CTS is typically used in a pure 802.11g environment. If CTS is set to “None” in a mixed mode environment populated by 802.11b clients, wireless collisions may occur frequently. Always: CTS will always be used to make sure the wireless LAN is clear before sending data. Auto: CTS will monitor the wireless network and automatically decide whether to implement CTS based on the amount of traffic and collisions that occurs on the wireless network.
35DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuAt this page, the DI-624M administrator can change the system password. There are two accounts that can access the Broadband Router’s Web-Management interface. They are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes.Tools > AdminAdminToolsThe Advanced tab provides the following options: Admin, Time, System, Firmware, and Misc.
36DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration Menuadmin is the Administrator login name.Enter the password and enter again to confirm.user is the User login name.Enter the password and enter again to confirmRemote management allows the DI-624M to be configured from the Internet by a web browser. A username and password is still required to access the Web-Management interface. In general, only a member of your network can browse the built-in web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host.The Internet IP address of the computer that has access to the Broadband Router. If you input an asterisk (*) into this field, then any computer will be able to access the Router. Putting an asterisk (*) into this field would present a security risk and is not recommended.The port number used to access the Broadband Router.http://x.x.x.x:8080 where x.x.x.x is the WAN IP address of the Broadband Router and 8080 is the port used for the Web-Mangement interface.
37DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuTimeSelect the Time Zone from the pull-down menu.NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. This field is optional.To manually input the time, enter the values in these fields for the Year, Month, Day, Hour, Minute, and Second. Click Set Time.To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time. Tools > Time
38DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuSystemThe current system settings can be saved as a file onto the local hard drive. The saved file or any other saved setting file can be loaded back on the Broadband Router. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used. You may also reset the Broadband Router back to factory settings by clicking on Restore. Click Save to save the current settings to the local Hard Drive.Click Browse to find the settings, then click Load. Click Restore to restore the factory default settings.BrowseTools > System
39DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuFirmwareYou can upgrade the firmware of the Router here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to browse the local hard drive and locate the firmware to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.Click on the link in this screen to find out if there is an updated firmware; if so, download the new firmware to your hard drive.After you have downloaded the new firmware, click Browse in this window to locate the firmware update on your hard drive. BrowseTools > Firmware
40DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuMisc.Tools > Misc.
41DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration Menu The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping.Click Reboot to restart the DI-624M.If you choose to block WAN Ping, the WAN IP Address of the DI-624M will not respond to pings. Blocking the Ping may provide some extra security from hackers.Discard Ping from WAN side: Click Enabled to block the WAN ping.To use the Universal Plug and Play feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals of the over 400 vendors that cooperate in the Plug and Play forum.Gaming mode allows a form of pass-through for certain Internet Games. If you are using Xbox, Playstation2 or a PC, make sure you are using the latest firmware and Gaming Mode is enabled. To utilize Gaming Mode, click Enabled. If you are not using a Gaming application, it is recommended that you Disable Gaming Mode.Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. This is a useful feature since many computers do not use a static IP address.The DI-624M supports VPN (Virtual Private Network) pass-through for both PPTP (Point-to-Point Tunneling Protocol) and IPSec (IP Security). Once VPN pass-through is enabled, there is no need to open up virtual services. Multiple VPN connections can be made through the DI-624M. This is useful when you
42DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuDevice InfoThis page displays the current information for the DI-624M. It will display the LAN, WAN and MAC address information. If your WAN connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your WAN connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.Status > Device InfoToolsThe Advanced tab provides the following options: Device Info, Log, Stats, and
43DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuIP Address: WAN/Public IP AddressSubnet Mask: WAN/Public Subnet MaskGateway: WAN/Public Gateway IP AddressDomain Name Server: WAN/Public DNS IP AddressWAN Status: WAN Connection StatusIP Address: LAN/Private IP Address of the DI-624MSubnet Mask: LAN/Private Subnet Mask of the DI-624MMAC Address: Displays the MAC addressSSID: Displays the current SSIDChannel: Displays the current channelWEP: indicates whether WEP is enabled or disabledThis window will show the DI-624M’s working status:
44DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuThe Broadband Router keeps a running log of events and activities occurring on the Router. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Settings.First Page - The first page of the log.Last Page - The last page of the log.Previous - Moves back one log page.Next - Moves forward one log page.Clear - Clears the logs completely.Log Settings - Brings up the page to configure the log.LogStatus > Log
45DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration Menu Not only does the Broadband Router display the logs of activities and events, it can setup to send these logs to another location. Log SettingsThe address of the SMTP server that will be used to send the logs.The email address to which the logs will be sent. Click on Send Mail Now to send the email.Status > Log > Log Settings
46DI-624M User’s Manual D-Link Systems, Inc.Using the Configuration MenuStatsThe screen above displays theTraffic Statistics. Here you can view the amount of packets that pass through the DI-624M on both the WAN and the LAN ports. The traffic counter will reset if the device is rebooted.The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless client. Click on Help at any time, for more information.WirelessStatus > StatsStatus > Wireless
47DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsNetworking BasicsUsing the Network Setup Wizard in Windows XPIn this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, ME or 98.Go to Start>Control Panel>Network Connections.Select Set up a home or small office network.When this screen appears, Click Next.
48DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsClick Next.In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as Click Next.Please follow all the instructions in this window:
49DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsEnter a Computer description and a Computer name (optional).Click Next.Enter a Workgroup name. All computers on your network should have the same Workgroup name.Click Next.
50DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsPlease wait while the Network Setup Wizard applies the changes.When the changes are complete, click Next.Please wait while the Network Setup Wizard configures the computer. This may take a few minutes.
51DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsInsert a disk into the Floppy Disk Drive, in this case drive A.Click Next.In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next.
52DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsPlease read the information under Here’s how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click
53DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsPlease read the information on this screen, then click Finish to complete the Network Setup Wizard.The new settings will take effect when you restart the computer. Click Yes to restart the computer.You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.
54DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsNaming Your ComputerTo name your computer, please follow these directions:In Windows XP:n Click Start (in the lower left corner of the screen).n Right-click on My Computer.n Select Properties and click.n Select the Computer Name Tab in the System Properties window.n You may enter a Computer Description if you wish; this field is optional.n To rename the computer and join a domain, Click Change.
55DI-624M User’s Manual D-Link Systems, Inc.Networking Basicsn In this window, enter the Computer name.n Select Workgroup and enter the name of the Workgroup.n All computers on your network must have the same Workgroup name.n Click OK.The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.) To check on the IP Address of the adapter, please do the following:n Right-click on the Local Area Connection icon in the task bar.n Click on Status.Checking the IP Address in Windows XP
56DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsThis window will appear:n Click the Support tab.n Click Close.
57DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsNote: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses.If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IP Address, please follow these instructions:n Go to Start.n Double-click on Control Panel.Assigning a Static IP Address in Windows n Double-click on Network Connections.
58DI-624M User’s Manual D-Link Systems, Inc.Networking Basicsn Right-click on Local Area Connections.n Click on Properties.n Click on Internet Protocol (TCP/IP).n Click Properties.n Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.)
59DI-624M User’s Manual D-Link Systems, Inc.Networking Basicsn Input your DNS server addresses. (Note: If you are entering a DNS server, you must enter the IP Address of the Default Gateway.)The DNS server information will be supplied by your ISP (Internet Service Provider.)n Click OK.Assigning a Static IP Address in Macintosh n Go to the Apple Menu and select System Preferences.n Click on Network.
60DI-624M User’s Manual D-Link Systems, Inc.Networking Basicsn Select Built-in Ethernet in the Show pull-down menu.n Select Manually in the Configure pull-down menu.n Input the Static IP Address, the Subnet Mask and the Router IP Address in the appropriate fields.n Click Apply Now.
61DI-624M User’s Manual D-Link Systems, Inc.Networking Basicsn Go to the Apple Menu and select System Preferences.n Click on Network.n Select Built-in Ethernet in the Show pull-down menu.n Select Using DHCP in the Configure pull-down menu.
62DI-624M User’s Manual D-Link Systems, Inc.Networking Basicsn Click Apply Now.n The IP Address, Subnet mask, and the Router’s IP Address will appear in a few seconds.Go to Start > Run > type cmd. A window similar to this one will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP Address of the Wireless Router or Access Point. A good wireless connection will show four replies from the Wireless Router or Acess Point, as shown.Checking the Wireless Connection by Pinging in Windows XP and 2000
63DI-624M User’s Manual D-Link Systems, Inc.Networking BasicsGo to Start > Run > type command. A window similar to this will appear. Type ping xxx.xxx.xxx.xxx where xxx is the IP Address of the Wireless Router or Access Point. A good wireless connection will show four replies from the wireless router or access point, as shown.Checking the Wireless Connection by Pinging in Windows Me and 98
64DI-624M User’s Manual D-Link Systems, Inc.TroubleshootingTroubleshootingThis Chapter provides solutions to problems that can occur during the installation and operation of the DI-624M Wireless Broadband Router. We cover various aspects of the network setup, including the network adapters. Please read the following if you are having problems.Note: It is recommended that you use an Ethernet connection to configure the DI-624M Wireless Broadband Router.Note: It is recommended that you use an Ethernet connection to configure the DI-624M Wireless Broadband Router.1. The computer used to configure the DI-624M cannot access the Configuration menu.n Check that the Ethernet LED on the DI-624M is ON. If the LED is not ON, check that the cable for the Ethernet connection is securely inserted.n Check that the Ethernet Adapter is working properly. Please see item 3 (Check that the drivers for the network adapters are installed properly) in this Troubleshooting section to check that the drivers are loaded properly.n Check that the IP Address is in the same range and subnet as the DI-624M. Please see Checking the IP Address in Windows XP in the Networking Basics section of this manual.Note: The IP Address of the DI-624M is 192.168.0.1. All the computers on the network must have a unique IP Address in the same range, e.g., 192.168.0.x. Any computers that have identical IP Addresses will not be visible on the network. They must all have the same subnet mask, e.g., 255.255.255.0.n Do a Ping test to make sure that the DI-624M is responding. Go to Start>Run>Type Command>Type ping 192.168.0.1. A successful ping will show four replies.Note: If you have changed the default IP Address, make sure to ping the correct IP Address assigned to the DI-624M.
65DI-624M User’s Manual D-Link Systems, Inc.Troubleshooting2. The wireless client cannot access the Internet in the Infrastructure mode.Make sure the wireless client is associated and joined with the correct Access Point. To check this connection: Right-click on the Local Area Connection icon in the taskbar> select View Available Wireless Networks. The Connect to Wireless Network screen will appear. Please make sure you have selected the correct available network, as shown in the illustrations below.n Check that the IP Address assigned to the wireless adapter is within the same IP Address range as the access point and gateway. (Since the DI-624M has an IP Address of 192.168.0.1, wireless adapters must have an IP Address in the same range, e.g., 192.168.0.x. Each device must have a unique IP Address; no two devices may have the same IP Address. The subnet mask must be the same for all the computers on the network.) To check the IP Address assigned to the wireless adapter, double-click on the Local Area Connection icon in the taskbar > select the Support tab and the IP Address will be displayed. (Please refer to Checking the IP Address in the Networking Basics section of this manual.)n If it is necessary to assign a Static IP Address to the wireless adapter, please refer to the appropriate section in Networking Basics. If you are entering a DNS Server address you must also enter the Default Gateway Address. (Remember that if you have a DHCP-capable router, you will not need to assign a Static IP default
66DI-624M User’s Manual D-Link Systems, Inc.Troubleshooting3. Check that the drivers for the network adapters are installed properly.You may be using different network adapters than those illustrated here, but this procedure will remain the same, regardless of the type of network adapters you are using.n Go to Start > My Computer > Properties.n Select the Hardware Tab.n Click Device Manager.
67DI-624M User’s Manual D-Link Systems, Inc.Troubleshootingn Double-click on Network Adapters.n Right-click on D-Link DWL-G650M Super G Smart Antenna Wireless Notebook Adapter. (In this example we use the DWL-G650M; you may be using other network adapters, but the procedure will remain the same.) n Select Properties to check that the drivers are installed properly.n Look under Device Status to check that the device is working properly.n Click OK.D-Link Super G Smart Antenna DWL-G650MD-Link Super G Smart Antenna DWL-G650M Wireless Cardbus D-Link Super G Smart Antenna DWL-G650M Wireless Cardbus Adapter
68DI-624M User’s Manual D-Link Systems, Inc.Troubleshooting4. What variables may cause my wireless products to lose reception?D-Link products let you access your network from virtually anywhere you want. However, the positioning of the products within your environment will affect the wireless range. Please refer to Installation Considerations in the Wireless Basics section of this manual for further information about the most advantageous placement of your D-Link wireless products.5. Why does my wireless connection keep dropping?n Antenna Orientation- Try different antenna orientations for the DI-624M. Try to keep the antenna at least 6 inches away from the wall or other objects.n If you are using 2.4GHz cordless phones, X-10 equipment or other home security systems, ceiling fans, and lights, your wireless connection will degrade dramatically or drop altogether. Try changing the Channel on your Router, Access Point and Wireless adapter to a different Channel to avoid interference.n Keep your product away (at least 3-6 feet) from electrical devices that generate RF noise, like microwaves, Monitors, electric motors, etc.6. Why can’t I get a wireless connection?If you have enabled Encryption on the DI-624M, you must also enable encryption on all wireless clients in order to establish a wireless connection.n For 802.11b, the Encryption settings are: 64, 128, or 256 bit. Make sure that the encryption bit level is the same on the Router and the Wireless Client.n Make sure that the SSID on the Router and the Wireless Client are exactly the same. If they are not, wireless connection will not be established. n Move the DI-624M and the wireless client into the same room and then test the wireless connection. n Disable all security settings. (WEP, MAC Address Control)\n Turn off your DI-624M and the client. Turn the DI-624M back on again, and then turn on the client. n Make sure that all devices are set to Infrastructure mode. n Check that the LED indicators are indicating normal activity. If not, check that the AC power and Ethernet cables are firmly connected.n Check that the IP Address, subnet mask, gateway and DNS settings are correctly entered for the network. n If you are using 2.4GHz cordless phones, X-10 equipment or other home security systems, ceiling fans, and lights, your wireless connection will degrade dramatically or drop altogether. Try changing the Channel on your DI-624M, and on all the devices in your network to avoid interference.n Keep your product away (at least 3-6 feet) from electrical devices that generate RF noise, like microwaves, Monitors, electric motors, etc.
69DI-624M User’s Manual D-Link Systems, Inc.Troubleshooting7. I forgot my encryption key.n Reset the DI-624M to its factory default settings and restore the other devices on your network to their default settings. You may do this by pressing the Reset button on the back of the unit. You will lose the current configuration settings. 8. Resetting the DI-624M to Factory Default SettingsAfter you have tried other methods for troubleshooting your network, you may choose to Reset the DI-624M to the factory default settings. Remember that D-Link Super G Smart Antenna products network together, out of the box, at the factory default settings. To hard-reset the DI-624M to Factory Default Settings, please do the following:n Locate the Reset button on the back of the DI-624M.n Use a paper clip to press the Reset button.n Hold for about 10 seconds and then release.n After the DI-62M reboots (this may take a few minutes) it will be reset to the factory Default settings.Reset Button
70DI-624M User’s Manual D-Link Systems, Inc.Technical SpecificationsStandardsn IEEE 802.11gn IEEE 802.11b n IEEE 802.3n IEEE 802.3uVPN Pass Through/ Multi-Sessionsn PPTPn L2TPn IPSecDevice Managementn Web-Based- Internet Explorer v6 or later; Netscape Navigator v7 or later; or other Java-enabled browsersn DHCP Server and ClientAdvanced Firewall Featuresn NAT with VPN Passthrough (Network Address Translation)n MAC Filteringn IP Filteringn URL Filteringn Domain Blockingn SchedulingWireless Operating Range n Indoors – up to 328 feet (100 meters)n Outdoors – up to 1312 feet (400 meters)Operating Temperaturen 32ºF to 131ºF (0ºC to 55ºC)Humidity:n 95% maximum (non-condensing)Safety and Emissions:n FCCWireless Frequency Range:n 2.4GHz to 2.462GHzTechnical Specifications
71DI-624M User’s Manual D-Link Systems, Inc.Technical SpecificationsLEDs:n Powern WANn LAN (10/100)n WLAN (Wireless Connection)Physical Dimensions:n L = 7.56 inches (192mm)n W = 4.65 inches (118mm)n H = 1.22 inches (31mm)Wireless Transmit Power:n 15dBm ± 2dBSecurity:n WPA- WiFi Protected Access (64-,128-WEP with TKIP, MIC, IV Expansion, Shared Key Authentication)External Antenna Type:n Dual non-detachable antennasModulation Technology:n Orthogonal Frequency Division Multiplexing (OFDM)Power Input:n Ext. Power Supply DC 5V, 2.5AWeight:n 10.8 oz. (0.3kg)Warranty:n 1 yearWireless Data Rates with Automatic Fallback:n 108 Mbpsn 54 Mbpsn 48 Mbpsn 36 Mbpsn 24 Mbpsn 18 Mbpsn 12 Mbpsn 11 Mbps
72DI-624M User’s Manual D-Link Systems, Inc.Technical Specificationsn 9 Mbpsn 6 Mbpsn 5.5 Mbpsn 2 Mbpsn 1 MbpsReceiver Sensitivity:n 108Mbpsn 54Mbps OFDM, 10% PER, -71dBmn 48Mbps OFDM, 10% PER, -71dBmn 36Mbps OFDM, 10% PER, -78dBmn 24Mbps OFDM, 10% PER, -82dBmn 18Mbps OFDM, 10% PER, -85dBmn 12Mbps OFDM, 10% PER, -87dBmn 11Mbps CCK, 8% PER, -85dBmn 9Mbps OFDM, 10% PER, -90dBmn 6Mbps OFDM, 10% PER, -91dBmn 5.5Mbps CCK, 8% PER, -88dBmn 2Mbps QPSK, 8% PER, -89dBmn 1Mbps BPSK, 8% PER, -92dBm
73DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsFrequently Asked Questions1 Why can´t I access the Web based configuration?When entering the IP Address of the DI-624M (192.168.0.1), you are not connecting to the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility.To resolve difficulties accessing a Web utility, please follow the steps below. Step 1: Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.What type of cable should I be using?The following connections require a Crossover Cable: Computer to Computer Computer to Uplink Port Computer to Access Point Computer to Print Server Computer/XBOX/PS2 to DWL-810 Computer/XBOX/PS2 to DWL-900AP+ Uplink Port to Uplink Port (hub/switch) Normal Port to Normal Port (hub/switch) The following connections require a Straight-through Cable: Computer to Residential Gateway/Router Computer to Normal Port (hub/switch) Access Point to Normal Port (hub/switch) Print Server to Normal Port (hub/switch) Uplink Port to Normal Port (hub/switch) Rule of Thumb: ”If there is a link light, the cable is right.”
74DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsWhat´s the difference between a crossover cable and a straight-through cable? The wiring in crossover and straight-through cables are different. The two types of cable have different purposes for different LAN configurations. EIA/TIA 568A/568B define the wiring standards and allow for two different wiring color codes as illustrated in the following diagram. *The wires with colored backgrounds may have white stripes and may be denoted that way in diagrams found elsewhere.How to tell straight-through cable from a crossover cable:The main way to tell the difference between the two cable types is to compare the wiring order on the ends of the cable. If the wiring is the same on both sides, it is straight-through cable. If one side has opposite wiring, it is a crossover cable.All you need to remember to properly configure the cables is the pinout order of the two cable ends and the following rules:A straight-through cable has identical ends. A crossover cable has different ends.It makes no functional difference which standard you follow for straight-through cable ends, as long as both ends are the same. You can start a crossover cable with either standard as long as the other end is the other standard. It makes no functional difference which end is which. The order in which you pin the cable is important. Using a pattern other than what is specified in the above diagram could cause connection problems.When to use a crossover cable and when to use a straight-through cable: Computer to Computer – CrossoverComputer to an normal port on a Hub/Switch – Straight-throughComputer to an uplink port on a Hub/Switch - CrossoverHub/Switch uplink port to another Hub/Switch uplink port – CrossoverHub/Switch uplink port to another Hub/Switch normal port - Straight-through
75DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsStep 2: Disable any Internet security software running on the computer. Software firewalls like Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, etc. might block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. Step 3: Configure your Internet settings. n Go to Start>Settings>Control Panel. Double click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults.n Click to the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
76DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questionsn Nothing should be checked. Click OK.n Go to the Advanced tab and click the button to restore these settings to their defaults.n Click OK. Go to the desktop and close any open windows.Step 4: Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to configure. Most D-Link devices use the 192.168.0.X range. How can I find my IP Address in Windows 95, 98, or ME? n Click on Start, then click on Run. n The Run Dialogue Box will appear. Type winipcfg in the window as shown then click OK.
77DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questionsn The IP Configuration window will appear, displaying your Ethernet Adapter Information.n Select your adapter from the drop down menu.n If you do not see your adapter in the drop down menu, your adapter is not properly installed. n After selecting your adapter, it will display your IP Address, subnet mask, and default gateway. n Click OK to close the IP Configuration window.How can I find my IP Address in Windows 2000/XP?n Click on Start and select Run.n Type cmd then click OK.
78DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questionsn From the Command Prompt, enter ipconfig. It will return your IP Address, subnet mask, and default gateway.n Type exit to close the command prompt.Make sure you take note of your computer´s Default Gateway IP Address. The Default Gateway is the IP Address of the D-Link router. By default, it should be 192.168.0.1How can I assign a Static IP Address in Windows 98/Me?n From the desktop, right-click on the Network Neigborhood icon (Win ME - My Network Places) and select Properties.n Highlight TCP/IP and click the Properties button. If you have more than 1 adapter, then there will be a TCP/IP “Binding” for each adapter. Highlight TCP/IP > (your network adapter) and then click Properties.
79DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questionsn Click Specify an IP Address.n Enter in an IP Address that is on the same subnet as the LAN IP Address on your router. Example: If the router´s LAN IP Address is 192.168.0.1, make your IP Address 192.168.0.X where X is between 2-99. Make sure that the number you choose is not in use on the network. n Click on the Gateway tab.n Enter the LAN IP Address of your router here (192.168.0.1).n Click Add when finished.
80DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questionsn Click on the DNS Configuration tab. n Click Enable DNS. Type in a Host (can be any word). Under DNS server search order, enter the LAN IP Address of your router (192.168.0.1). Click Add. n Click OK twice. n When prompted to reboot your computer, click Yes. After you reboot, the computer will now have a static, private IP Address.
81DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsHow can I assign a Static IP Address in Windows 2000? n Right-click on My Network Places and select Properties.n Right-click on the Local Area Connection which represents your network card and select Properties. n Highlight Internet Protocol (TCP/IP) and click Properties.n Click Use the following IP Address and enter an IP Address that is on the same subnet as the LAN IP Address on your router. Example: If the router´s LAN IP Address is 192.168.0.1, make your IP Address 192.168.0.X where X = 2-99. Make sure that the number you choose is not in use on the network. n Set the Default Gateway to be the same as the LAN IP Address of your router (192.168.0.1). n Set the Primary DNS to be the same as the LAN IP address of your router (192.168.0.1).
82DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questionsn The Secondary DNS is not needed or enter a DNS server from your ISP. n Click OK twice. You may be asked if you want to reboot your computer. Click Yes.How can I assign a Static IP Address in Windows XP? n Click on Start > Control Panel > Network and Internet Connections > Network connections.n See the second step for assigning a static IP address in Windows 2000 and continue from there.Step 5: Access the Web management. Open your Web browser and enter the IP Address of your D-Link device in the address bar. This should open the login page for the Web management. Follow instructions to login and complete the configuration. 2 How can I setup my router to work with a Cable modem connection?Dynamic Cable connection (IE AT&T-BI, Cox, Adelphia, Rogers, Roadrunner, Charter, and Comcast). Note: Please configure the router with the computer that was last connected directly to the cable modem. Step 1: Log into the web based configuration by typing in the IP Address of the router (default:192.168.0.1) in your web browser. The username is admin (all lowercase) and the password is blank (nothing).
83DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questions Step 2: Click the Home tab and click the WAN button. Dynamic IP Address is the default value, however, if Dynamic IP Address is not selected as the WAN type, select Dynamic IP Address by clicking on the radio button. Click Clone Mac Address. Click on Apply and then Continue to save the changes.
84DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsStep 3: Power cycle the cable modem and router. Turn the cable modem off (first) . Turn the router off Leave them off for 2 minutes.** Turn the cable modem on (first). Wait until you get a solid cable light on the cable modem. Turn the router on. Wait 30 seconds. ** If you have a Motorola (Surf Board) modem, leave off for at least 5 minutes. Step 4: Follow step 1 again and log back into the web configuration. Click the Status tab and click the Device Info button. If you do not already have a public IP Address under the WAN heading, click on the DHCP Renew and Continue buttons.Static Cable ConnectionStep 1: Log into the web based configuration by typing in the IP Address of the router (default:192.168.0.1) in your web browser. The username is admin (all lowercase) and the password is blank (nothing). Step 2: Click the Home tab and click the WAN button. Select Static IP Address and enter your static settings obtained from the ISP in the fields provided. If you do not know your settings, you must contact your ISP.
85DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsStep 3: Click on Apply and then click Continue to save the changes. Step 4: Click the Status tab and click the Device Info button. Your IP Address information will be displayed under the WAN heading.3 How can I setup my router to work with Earthlink DSL or any PPPoE connection? Make sure you disable or uninstall any PPPoE software such as WinPoet or Enternet 300 from your computer or you will not be able to connect to the Internet. Step 1: Upgrade Firmware if needed. (Please visit the D-Link tech support website at: http://support.dlink.com for the latest firmware upgrade information.) Step 2: Take a paperclip and perform a hard reset. With the unit on, use a paperclip and hold down the reset button on the back of the unit for 10 seconds. Release it and the router will recycle, the lights will blink, and then stabilize.
86DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsStep 3: After the router stabilizes, open your browser and enter 192.168.0.1 into the address window and hit the Enter key. When the password dialog box appears, enter the username admin and leave the password blank. Click OK.If the password dialog box does not come up repeat Step 2. Note: Do not run Wizard. Step 4: Click on the WAN tab on left-hand side of the screen. Select PPPoE. Step 5: Select Dynamic PPPoE (unless your ISP supplied you with a static IP Address). Step 6: In the username field enter ELN/username@earthlink.net and your password, where username is your own username. For SBC Global users, enter username@sbcglobal.net.For Ameritech users, enter username@ameritech.net.For BellSouth users, enter username@bellsouth.net.For Mindspring users, enter username@mindspring.com.For most other ISPs, enter username. Step 7: Maximum Idle Time should be set to zero. Set MTU to 1492, unless specified by your ISP, and set Autoreconnect to Enabled. Note: If you experience problems accessing certain websites and/or email issues, please set the MTU to a lower number such as 1472, 1452, etc. Contact your ISP for more information and the proper MTU setting for your connection.Step 8: Click Apply. When prompted, click Continue. Once the screen refreshes, unplug the power to the D-Link router. Step 9: Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem has established a link to your ISP, plug the power back into the D-Link router. Wait about 30 seconds and log back into the router. Step 10: Click on the Status tab in the web configuration where you can view the device info. Under WAN, click Connect. Click Continue when prompted. You should now see that the device info will show an IP Address, verifying that the device has connected
87DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questions4 Can I use my D-Link Broadband Router to share my Internet connection provided by AOL DSL Plus?In most cases yes. AOL DSL+ may use PPPoE for authentication bypassing the client software. If this is the case, then our routers will work with this service. Please contact AOL if you are not sure.To set up your router:Step 1: Log into the web-based configuration (192.168.0.1) and configure the WAN side to use PPPoE. Step 2: Enter your screen name followed by @aol.com for the user name. Enter your AOL password in the password box. Step 3: You will have to set the MTU to 1400. AOL DSL does not allow for anything higher than 1400.Step 4: Apply settings. Step 5: Recycle the power to the modem for 1 minute and then recycle power to the router. Allow 1 to 2 minutes to connect. If you connect to the Internet with a different internet service provider and want to use the AOL software, you can do that without configuring the router’s firewall settings. You need to configure the AOL software to connect using TCP/IP. Go to http://www.aol.com for more specific configuration information of their software.5 How do I open ports on my router?To allow traffic from the internet to enter your local network, you will need to open up ports or the router will block the request. Step 1: Open your web browser and enter the IP Address of your D-Link router (192.168.0.1). Enter username (admin) and your password (blank by default). Step 2: Click on Advanced on top and then click Virtual Server on the left side.
88DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsStep 3: Check Enabled to activate entry. Step 4: Enter a name for your virtual server entry. Step 5: Next to Private IP, enter the IP Address of the computer on your local network that you want to allow the incoming service to. Step 6: Choose Protocol Type - either TCP, UDP, or both. If you are not sure, select both. Step 7: Enter the port information next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the WAN side, and the private port is the port being used by the application on the computer within your local network. Step 8: Enter the Schedule information. Step 9: Click Apply and then click Continue. Note: Make sure DMZ host is disabled. If DMZ is enabled, it will disable all Virtual Server entries. Because our routers use NAT (Network Address Translation), you can only open a specific port to one computer at a time. For example: If you have 2 web servers on your network, you cannot open port 80 to both computers. You will need to configure 1 of the web servers to use port 81. Now you can open port 80 to the first computer and then open port 81 to the other computer.
89DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked Questions6 What is DMZ?Demilitarized Zone:In computer networks, a DMZ (demilitarized zone) is a computer host or small network inserted as a neutral zone between a company´s private network and the outside public network. It prevents outside users from getting direct access to a server that has company data. (The term comes from the geographic buffer zone that was set up between North Korea and South Korea following the UN police action in the early 1950s.) A DMZ is an optional and more secure approach to a firewall and effectively acts as a proxy server as well.In a typical DMZ configuration for a small company, a separate computer (or host in network terms) receives requests from users within the private network for access to Web sites or other companies accessible on the public network. The DMZ host then initiates sessions for these requests on the public network. However, the DMZ host is not able to initiate a session back into the private network. It can only forward packets that have already been requested.Users of the public network outside the company can access only the DMZ host. The DMZ may typically also have the company´s Web pages so these could be served to the outside world. However, the DMZ provides access to no other company data. In the event that an outside user penetrated the DMZ hosts security, the Web pages might be corrupted but no other company information would be exposed. D-Link, a leading maker of routers, is one company that sells products designed for setting up a DMZ7 How do I configure the DMZ Host?The DMZ feature allows you to forward all incoming ports to one computer on the local network. The DMZ, or Demilitarized Zone, will allow the specified computer to be exposed to the Internet. DMZ is useful when a certain application or game does not work through the firewall. The computer that is configured for DMZ will be completely vulnerable on the Internet, so it is suggested that you try opening ports from the Virtual Server or Firewall settings before using DMZ. Step 1: Find the IP address of the computer you want to use as the DMZ host.To find out how to locate the IP Address of the computer in Windows XP/2000/ME/9x or Macintosh operating systems please refer to Step 4 of the first question in this section (Frequently Asked Questions).
90DI-624M User’s Manual D-Link Systems, Inc.Frequently Asked QuestionsStep 2: Log into the web based configuration of the router by typing in the IP Address of the router (default:192.168.0.1) in your web browser. The username is admin (all lowercase) and the password is blank (nothing)Step 3: Click the Advanced tab and then click on the DMZ button. Select Enable and type in the IP Address you found in step 1. Step 4: Click Apply and then Continue to save the changes. Note: When DMZ is enabled, Virtual Server settings will still be effective. Remember, you cannot forward the same port to multiple IP Addresses, so the Virtual Server settings will take priority over DMZ settings.

Navigation menu