D Link DVA-G3672B Wireless ADSL VOIP Router User Manual D Link DVA G3672B

D Link Corporation Wireless ADSL VOIP Router D Link DVA G3672B

Contents

Users Manual 3

Chapter 2 Configuration Routing – Default Gateway To access Default Gateway, point to the Routing on the left window and click Default Gateway submenu, or click the Default Gateway button in the Routing window. This page can either automatically assign a default gateway to the device or manually type in a default gateway or the device or interface. It is recommended to leave Enable Automatic Assigned Default Gateway ticked to automatically detect the Gateway IP address. Routing – RIP To access RIP, point to the Routing on the left window and click RIP submenu, or click the RIP button in the Routing window. The Router supports RIP version 1 and 2 used to share routing tables with other Layer 3 routing devices on your local network or remote LAN. The Operation setting refers to the RIP request. Select Active to allow RIP requests from other devices. Select Passive to instruct the Router to make RIP requests for routing tables from other devices. To enable RIP, tick the Enable Global RTP Mode check box, select the Version (1, 2, or Both) and Operation (Active or Passive), and tick the Enable check box in the corresponding entry. Click the Apply button. Go to Maintenance -> System and click Reboot to restart the device and let your changes take effect. D-Link DVA-G3672B User Manual 56
Chapter 2 Configuration Advanced – Schedules To access the Schedules window, click the schedules button in the Advanced directory. You can add schedules in this page and then apply them to Parental Control. Click Add to see the Add Schedule Rule section. Enter a Name for the schedule. Use the radio buttons to click the desired Day(s), either All Week or Select Day(s) (in which case you must tick the checkboxes for the desired individual days of the week), select the desired Start Time and End Time or tick the All Day – 24 hrs checkbox. Click Apply to see the entry in the Schedule Rule table. To remove an entry in the table, click the corresponding button. To modify a table entry, click the corresponding button, make the desired changes, and then click the Apply button. D-Link DVA-G3672B User Manual 57
Chapter 2 Configuration Advanced – Voice To access the Voice window, click the Voice button in the Advanced directory. You can set up the basic VoIP settings in this page. All information in this page should be obtained by your ISP. Voice over Internet Protocol (VoIP) is a protocol that can transmit the voice through the Internet. Session Initiation Protocol (SIP) is a widely used signaling protocol of VoIP. To start using the VoIP service, select an interface in the Interface list for the VoIP service, and enter the Primary SIP Server IP and Primary SIP Server Port. The Secondary SIP Server, Outbound Proxy IP, Stun Server and SIP Service Domain are optional. Tick Enable T38 Fax for sending fax data through the network. Tick Enable VAD to disable silent packet and send other transmission. Select a DTMF type (Inband, RFC2833 or SIP Info) in the DTMF relay drop-down list. Tick one of forwarding call methods for All, No Answer or Busy calls, and then type a number that calls is forwarded to. Select a routing rule of the PSTN line (auto, Line1 or Line2) in the PSTN Routing drop-down list. Enter digits in the PSTN Dialplan field for transferring VoIP service to PSTN service. You can also set up the codec priorities in Codec Settings section. In VoIP Setting section, you can configure the user name and password for registering to SIP VoIP service. Click the Apply button, and go to Maintenance -> System and click Reboot to restart the device and let your changes take effect. D-Link DVA-G3672B User Manual 58
Chapter 2 Configuration Advanced –Print Server To access the Print Server window, click the Print Server button in the Advanced directory. Tick the Enable on-board print server check box, enter a Printer Name and Model name in the fields, and click Apply to enable the printer server function. D-Link DVA-G3672B User Manual 59
Chapter 2 Configuration Maintenance – System To access the System window, click the System button in the Maintenance directory. When you configure the Router, you will need to restart the Router to take the settings effect. Click Reboot to restart the Router. Once you have configured the Router to your satisfaction, it is a good idea to back up the configuration file to your computer. To save the current configuration settings to your computer, click the Backup Settings button. You will be prompted to select a location on your computer to put the file. The file type is bin and may be named anything you wish. To load a previously saved configuration file, click the Browse button and locate the file on your computer. Click the Upload Settings button to load the settings from your local hard drive. Confirm that you want to load the file when prompted. The Router will reboot and begin operating with the configuration settings that have just been loaded. To reset the Router to its factory default settings, click the Restore Default Settings button. You will be prompted to confirm your decision to reset the Router. The Router will reboot with the factory default settings including IP settings (192.168.1.1) and Administrator password (admin). D-Link DVA-G3672B User Manual 60
Chapter 2 Configuration Maintenance – Firmware Update To access the Firmware Update window, click the Firmware Update button in the Maintenance directory. Use the Firmware Upgrade menu to load the latest firmware for the Router. Note that the Router configuration settings may return to the factory default settings, so make sure you save the configuration settings with the System menu described above. To upgrade firmware obtained from your ISP, click the Browse button to search for the file. Click the Update Firmware button to begin copying the file. The file will load and restart the Router automatically. D-Link DVA-G3672B User Manual 61
Chapter 2 Configuration Maintenance – Access Controls To access the Access Controls window, click the Access Controls button in the Maintenance directory. In this page, you can choose to change password, manage the service control or IP address control. D-Link DVA-G3672B User Manual 62
Chapter 2 Configuration Access Controls – Account Password To access Account Password, point to the Access Controls on the left window and click Account Password submenu, or click the Account Password button in the Access Controls window. There are three different user names for different purpose. Support is for remote supporter to login from WAN and is able to adjust TR-069 settings. User and Admin is to login from LAN. Select a user name (Admin, User or Support), type the Current Password in the first field, the New Password in the second field, and enter the password again in the Confirm Password field to be certain you have typed it correctly. You can configure the idle time between 5 and 30 minutes for the webpage asking you to logout. Click the Apply button. Go to Maintenance -> System and click Reboot to restart the device. D-Link DVA-G3672B User Manual 63
Chapter 2 Configuration Access Controls – Services To access Services, point to the Access Controls on the left window and click Services submenu, or click the Services button in the Access Controls window. This page lists out all the available services including Telnet, FTP, HTTP, ICMP, SNMP, SSH and TFTP that can enable at LAN, WAN or both. Tick to enable the services, or deselect to disable them. Access Controls – IP Address To access IP Address, point to the Access Controls on the left window and click IP Address submenu, or click the IP Address button in the Access Controls window. Click Add to see the Add IP Address section. Enter an IP address and click Apply in the section. The IP address will show in the table in the Remote Web and Telnet Management section. Tick the Enable Access Control Mode check box and click Apply in this section to enable the function. D-Link DVA-G3672B User Manual 64
Chapter 2 Configuration Maintenance – Diagnostics To access the Diagnostics window, click the Diagnostics button in the Maintenance directory. This window is used to test connectivity of the Router. A Ping test may be done through the local or external interface to test connectivity to known IP addresses. The diagnostics feature executes a series of tests of your system software and hardware connections. Use this window when working with your ISP to troubleshoot problems. D-Link DVA-G3672B User Manual 65
Chapter 2 Configuration Maintenance – System Log To access the System Log window, click the System Log button in the Maintenance directory. The system log allows you to configure local and remote logging, and to view the logs that have been created. To generate a system log, tick the Enable Remote Log check box. Select the Log Level and Display Level from the drop-down lists. The levels available are the same for each type of level: Emergency, Alert, Critical, Error, Warning, Notice, Informational and Debugging. Click the Apply button to allow your new settings to take effect. D-Link DVA-G3672B User Manual 66
Chapter 2 Configuration Status – Device Info Use the Device Information window to quickly view basic current information about the Wireless, WAN and local network interfaces, and device information including Model Name, Time and Date, and Firmware. D-Link DVA-G3672B User Manual 67
Chapter 2 Configuration Status – Wireless Clients To access the Wireless Clients window, click the Wireless Clients button in the Status directory. The Wireless Clients window lists out the active Wireless connection when the Wireless function is on. Status – DHCP Clients To access the DHCP Clients window, click the DHCP Clients button in the Status directory. The Connected LAN Clients list displays active DHCP clients when the Router is acting as a DHCP server. D-Link DVA-G3672B User Manual 68
Chapter 2 Configuration Status – Logs To access the Logs window, click the Logs button in the Status directory. This page displays the event logs of the Router. Click Clear Log to delete all the records. Click Save Log to save the records as a *.sys file. D-Link DVA-G3672B User Manual 69
Chapter 2 Configuration Status – Statistics To access the Statistics window, click the Statistics button in the Status directory. Use this window to monitor traffic on the Local Network & Wireless, Internet or ADSL connections. This window also displays information concerning ADSL status. D-Link DVA-G3672B User Manual 70
Chapter 2 Configuration Status – Routing Info To access the Routing Info window, click the Routing Info button in the Status directory. This page displays all the routing rules information. D-Link DVA-G3672B User Manual 71
Chapter 2 Configuration Help To access the Help window, click the Help directory. D-Link DVA-G3672B User Manual 72
FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance."

Navigation menu