D Link IR615E1 D-Link DIR-615 Wireless N Router User Manual Manual Part 2

D Link Corporation D-Link DIR-615 Wireless N Router Manual Part 2

Contents

Manual Part 2

21D-Link DIR-615 User ManualSection 3 - ConfigurationSelect PPPoE (Username/Password) from the drop-down menu.Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).My Internet Connection:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time:DNS Addresses:PPPoE (DSL)Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
22D-Link DIR-615 User ManualSection 3 - ConfigurationMTU:MAC Address:Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU.The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
23D-Link DIR-615 User ManualSection 3 - ConfigurationSelect Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPTP only).Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).Enter the Gateway IP Address provided by your ISP.Enter the Server IP provided by your ISP (optional).Enter your PPTP username.Enter your PPTP password and then retype the password in the next box.Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.The DNS server information will be supplied by your ISP (Internet Service Provider.)Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default MTU.Address Mode:PPTP IP Address:PPTP Subnet Mask:PPTP Gateway:PPTP Server IP:PPTPChoose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Username:Password: Reconnect Mode:Maximum Idle Time:DNS Servers:MTU:
24D-Link DIR-615 User ManualSection 3 - ConfigurationThe default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.MAC Address:
25D-Link DIR-615 User ManualSection 3 - ConfigurationSelect Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the L2TP IP address supplied by your ISP (Static only).Enter the Subnet Mask supplied by your ISP (Static only).Enter the Gateway IP Address provided by your ISP.Enter the Server IP provided by your ISP (optional).Enter your L2TP username.Enter your L2TP password and then retype the password in the next box.Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).Address Mode:L2TP IP Address:L2TP Subnet Mask:L2TP Gateway:L2TP Server IP:Username:Password:Reconnect Mode:Maximum Idle Time: DNS Servers:L2TPChoose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
26D-Link DIR-615 User ManualSection 3 - ConfigurationMTU:Clone MAC Address:Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default MTU.The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
27D-Link DIR-615 User ManualSection 3 - ConfigurationEnter the IP address assigned by your ISP.Enter the Subnet Mask assigned by your ISP.Enter the Gateway assigned by your ISP.The DNS server information will be supplied by your ISP (Internet Service Provider.)Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU.The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.IP Address:Subnet Mask:Default Gateway:DNS Servers:MTU:MAC Address:Static IP AddressSelect Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
28D-Link DIR-615 User ManualSection 3 - ConfigurationWireless SettingsIf you want to configure the wireless settings on your router using the wizard, click Wireless Network Setup Wizard and refer to page 79.Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 82.If you want to manually configure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
29D-Link DIR-615 User ManualSection 3 - ConfigurationManual Wireless Network SetupCheck the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Click Add New to create your own time schedule to enable the wireless function. Service Set Identifier (SSID) is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive.Select one of the following:802.11g Only - Select if all of your wireless clients are 802.11g.Mixed 802.11g and 802.11b - Select if you are using both 802.11b and 802.11g wireless clients.802.11b Only - Select if all of your wireless clients are 802.11b.802.11n Only - Select only if all of your wireless clients are 802.11n.Mixed 802.11n, 802.11b, and 802.11g - Select if you are using a mix of 802.11n, 11g, and 11b wireless clients.Mixed 802.11n and 802.11g - Select if you are using a mix of 802.11n and 802.11g wireless clients.The Auto Channel Scan setting can be selected to allow the DIR-615 to choose the channel with the least amount of interference.Indicates the channel setting for the DIR-615. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be greyed out.Enable Wireless:Wireless Network Name:802.11 Mode:Enable Auto Channel Scan:Wireless Channel:
30D-Link DIR-615 User ManualSection 3 - ConfigurationSelect the transmit rate. It is strongly suggested to select Best (Auto) for best performance.Select the Channel Width:Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting. Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-615. If Invisible is selected, the SSID of the DIR-615 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-615 in order to connect to it.Refer to page 79 for more information regarding wireless security.Visibility Status:Wireless Security:Channel Width:Transmission Rate:
31D-Link DIR-615 User ManualSection 3 - ConfigurationThis section will allow you to change the local network settings of the router and to configure the DHCP settings.Network SettingsEnter the IP address of the router. The default IP address is 192.168.0.1.If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility.Enter the Subnet Mask. The default subnet mask is 255.255.255.0.Enter the Domain name (Optional).Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server.IP Address:Subnet Mask:Local Domain:Enable DNS Relay:
32D-Link DIR-615 User ManualSection 3 - ConfigurationCheck this box to enable the DHCP server on your router. Uncheck to disable this function.Enter the starting and ending IP addresses for the DHCP server’s IP assignment.Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict. The length of time for the IP address lease. Enter the Lease time in minutes.Enable this function to ensure compatibility with some DHCP clients.If NetBIOS advertisement is switched on, switching this setting on causes WINS information to be learned from the WAN side, if available. Turn this setting off to configure manually. This is an advance setting and is normally left blank. This allows the configuration of NetBIOS domain name under which network hosts operate. This setting has no effect if the “ Learn NetBIOS information form WAN is activated. Enable DHCP Server:DHCP IP Address Range:Lease Time:Always Broadcast:Learn NetBIOS WAN:Net BIOS scope: DHCP Server SettingsDHCP stands for Dynamic Host Control Protocol. The DIR-615 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-615. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.
33D-Link DIR-615 User ManualSection 3 - ConfigurationDHCP ReservationIf you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range.Check this box to enable the reservation.Enter the computer name or select from the drop-down menu and click <<.Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP Address Range.Enter the MAC address of the computer or device.If you want to assign an IP address to the computer you are currently on, click this button to populate the fields. Click Save to save your entry. You must click Save Settings at the top to activate your reservations. In this section you can see what LAN devices are currently leasing IP addresses.Click Revoke to cancel the lease for a specific LAN device and free an entry in the lease table. Do this only if the device no longer needs the leased IP address, because, for example, it has been removed from the network.Enable:Computer Name:IP Address:MAC Address:Copy Your PC’s MAC Address:Save:Number of Dynamic DHCP Clients:Revoke:
34D-Link DIR-615 User ManualSection 3 - ConfigurationReserve:Note: The Revoke option will not disconnect a PC with a current network session from the network; you would need to use MAC Address Filter to do that. Revoke will only free up a DHCP Address for the very next requester. If the previous owner is still available, those two devices may both receive an IP Address Conflict error, or the second device may still not receive an IP Address; in that case, you may still need to extend the “DHCP IP Address Range” to address the issue, it is located in the DHCP Server section. The Reserve option converts this dynamic IP allocation into a DHCP Reservation and adds the corresponding entry to the DHCP Reservations List.
35D-Link DIR-615 User ManualSection 3 - ConfigurationThe DIR-615 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-615 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DIR-615 are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the DIR-615 redirects the external service request to the appropriate server within the LAN network. The DIR-615 is also capable of port-redirection meaning incoming traffic to a particular port may be redirected to a different port on the server computer.Each virtual service that is created will be listed at the bottom of the screen in the Virtual Servers List. There are pre-defined virtual services already in the table. You may use them by enabling them and assigning the server IP to use that particular virtual service.For a list of ports for common applications, please visit http://support.dlink.com/faq/view.asp?prod_id=1191.Virtual Server
36D-Link DIR-615 User ManualSection 3 - ConfigurationThis will allow you to open a single port. If you would like to open a range of ports, refer to the next page.Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields.Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the “Computer Name” drop-down menu. Select your computer and click <<. Enter the port that you want to open next to Private Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network.Select TCP, UDP, or Both from the drop-down menu.Select Allow All (most common) or a created Inbound filter. You may create your own inbound filters in the Advanced > Inbound Filter page.The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:IP Address:Private Port/Public Port:Protocol Type:Inbound Filter:Schedule:
37D-Link DIR-615 User ManualSection 3 - ConfigurationThis will allow you to open a single port or a range of ports.Port ForwardingEnter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields.Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the “Computer Name” drop-down menu. Select your computer and click <<. Enter the TCP and/or UDP port or ports that you want to open. You can enter a single port or a range of ports. Separate ports with a common.Example: 24,1009,3000-4000Select Allow All (most common) or a created Inbound filter. You may create your own inbound filters in the Advanced > Inbound Filter page.The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:IP Address:TCP/UDP:Inbound Filter:Schedule:
38D-Link DIR-615 User ManualSection 3 - ConfigurationEnter a name for the rule. You may select a pre-defined application from the drop-down menu and click <<.This is the port used to trigger the application. It can be either a single port or a range of ports.Select the protocol of the trigger port (TCP, UDP, or Both).This is the port number on the Internet side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges.Select the protocol of the firewall port (TCP, UDP, or Both).The schedule of time when the Application Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.Name:Trigger:Traffic Type:Firewall:Traffic Type:Schedule:Application RulesSome applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-615. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or UDP, then enter the firewall (public) ports associated with the trigger port to open them for inbound traffic.The DIR-615 provides some predefined applications in the table on the bottom of the web page. Select the application you want to use and enable it.
39D-Link DIR-615 User ManualSection 3 - ConfigurationQoS EngineThis option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.This option is enabled by default when the QoS Engine option is enabled. This option will allow your router to automatically determine the uplink speed of your Internet connection.This displays the detected uplink speed.The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s offer speed as a download/upload pair. For example, 1.5Mbits/284Kbits. Using this example, you would enter 284. Alternatively you can test your uplink speed with a service such as www.dslreports.com.Enable QoS Engine:Automatic Uplink Speed:Measured Uplink Speed:Manual Uplink Speed:The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically.
40D-Link DIR-615 User ManualSection 3 - ConfigurationNetwork FiltersSelect Turn MAC Filtering Off, allow MAC addresses listed below, or deny MAC addresses listed below from the drop-down menu. Enter the MAC address you would like to filter.To find the MAC address on a computer, please refer to the Networking Basics section in this manual. Select a DHCP client from the drop-down menu and click << to copy that MAC Address. Configure MAC Filtering:MAC Address:DHCP Client:Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
41D-Link DIR-615 User ManualSection 3 - ConfigurationAccess ControlCheck the Enable Access Control check box and click the Add Policy button to start the Access Control Wizard. Add Policy:The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games.Click Next to continue with the wizard.Access Control Wizard
42D-Link DIR-615 User ManualSection 3 - ConfigurationEnter a name for the policy and then click Next to continue.Access Control Wizard (continued)Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue.Enter the following information and then click Next to continue.• Address Type - Select IP address, MAC address, or Other Machines.• IP Address - Enter the IP address of the computer you want to apply the rule to.
43D-Link DIR-615 User ManualSection 3 - ConfigurationSelect the filtering method and then click Next to continue.Access Control Wizard (continued)Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number.To enable web logging, click Enable.Click Save to save the access control rule.
44D-Link DIR-615 User ManualSection 3 - ConfigurationSelect Deny or Allow computers access to only these sites.Click to delete all entries in the list.Enter the keywords or URLs that you want to allow or deny.Configure Website Filter Below:Clear the list below:Website URL/Domain:Website FiltersWebsite Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Add, and then click Save Settings. You must also select Apply Web Filter under the Access Control section (page 40).
45D-Link DIR-615 User ManualSection 3 - ConfigurationEnter a name for the inbound filter rule.Select Allow or Deny.Check to enable rule.Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range.Enter the ending IP address. Enter 255.255.255.255 if you do not want to specify and IP range.Click the Save button to apply your settings. You must click Save Settings at the top to save the settings.This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule.Name:Action:Enable:Source IP Start:Source IP End:Save:Inbound Filter Rules List:The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features.Inbound Filters
46D-Link DIR-615 User ManualSection 3 - ConfigurationSPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol.Select one of the following for TCP and UDP ports:Endpoint Independent - Any incoming traffic sent to an open port will be forwarded to the application that opened the port. The port will close if idle for 5 minutes.Address Restricted - Incoming traffic must match the IP address of the outgoing connection.Address + Port Restriction - Incoming traffic must match the IP address and port of the outgoing connection.Enable this option to provide protection from certain kinds of “spoofing” attacks.If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer.Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains its IP address automatically using DHCP, be sure to make a static reservation on the System > Network Settings page so that the IP address of the DMZ machine does not change.Enable SPI:NAT Endpoint Filtering:Enable Anti-Spoof Checking:Enable DMZ Host:IP Address:Firewall SettingsA firewall protects your network from the outside world. The D-Link DIR-615 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
47D-Link DIR-615 User ManualSection 3 - ConfigurationRouting This page allows you to specify custom routes that determine how data is moved around your network. Routing List:Name:Destination IP:Netmask:Gateway:Each Route has a checkbox next to it, check the box of the route you wish to enable. Specify a name for identification of this route.Enter the address of the host or network you wish to access.This field identifies the portion of the destination IP in use. The IP address of the router will be displayed here.
48D-Link DIR-615 User ManualSection 3 - ConfigurationSet the transmit power of the antennas.Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. This value should remain at its default setting of 2432. If inconsistent data flow is a problem, only a minor modification should be made.The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 2346 byte setting will be fragmented before transmission. 2346 is the default setting. (Delivery Traffic Indication Message) 3 is the default setting. A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages.This enables 802.11d operation. 802.11d is a wireless specification developed to allow implementation of wireless networks in countries that cannot use the 802.11 standard. This feature should only be enabled if you are in a country that requires it.WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.Transmit Power:Beacon Period:RTS Threshold:Fragmentation Threshold:DTIM Interval:WLAN Partition:WMM Enable:Short GI:Advanced Wireless Settings
49D-Link DIR-615 User ManualSection 3 - ConfigurationUPnPInternet Ping BlockInternet Port SpeedMulticast StreamsTo use the Universal Plug and Play (UPnP™) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals.Unchecking the box will not allow the DIR-615 to respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.You may set the port speed of the Internet port to 10Mbps, 100Mbps, or auto. Some older cable or DSL modems may require you to set the port speed to 10Mbps.Check the box to allow multicast traffic to pass through the router from the Internet.UPnP Settings:WAN Ping:WAN Port Speed:Multicast Streams:Advanced Network Settings
50D-Link DIR-615 User ManualSection 3 - ConfigurationIPv6Select Link-Local Only from the drop-down menu.Displays the IPv6 address of the router.My IPv6 Connection:LAN IPv6 Address Settings:Link-Local Connectivity
51D-Link DIR-615 User ManualSection 3 - ConfigurationStatic IPv6 (Stateful)Select Static IPv6 from the drop-down menu.Enter the address settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:WAN IPv6 Address Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
52D-Link DIR-615 User ManualSection 3 - ConfigurationStatic IPv6 (Stateless)Select Static IPv6 from the drop-down menu.Enter the address settings supplied by your Internet provider (ISP). Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:WAN IPv6 Address Settings:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:
53D-Link DIR-615 User ManualSection 3 - ConfigurationDHCPv6 (Stateful)Select DHCPv6 from the drop-down menu.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
54D-Link DIR-615 User ManualSection 3 - ConfigurationDHCPv6 (Stateless)Select DHCPv6 from the drop-down menu.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:
55D-Link DIR-615 User ManualSection 3 - ConfigurationIPv6 over PPPoE (Stateful)Select PPPoE from the drop-down menu.Enter the PPPoE account settings supplied by your Internet provider (ISP). Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.My IPv6 Connection:PPPoE:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:
56D-Link DIR-615 User ManualSection 3 - ConfigurationEnable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).
57D-Link DIR-615 User ManualSection 3 - ConfigurationIPv6 over PPPoE (Stateless)Select PPPoE from the drop-down menu.Enter the PPPoE account settings supplied by your Internet provider (ISP). Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.Enter the IP address (Static PPPoE only).Enter your PPPoE user name.Enter your PPPoE password and then retype the password in the next box.Enter the ISP Service Name (optional).Select either Always-on, On-Demand, or Manual.Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect.Select either Obtain DNS server address automatically or Use the following DNS Address.Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.My IPv6 Connection:PPPoE:Address Mode:IP Address:User Name:Password:Service Name:Reconnection Mode:Maximum Idle Time:IPv6 DNS Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:
58D-Link DIR-615 User ManualSection 3 - ConfigurationEnable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Enter the Router Advertisement Lifetime (in minutes).
59D-Link DIR-615 User ManualSection 3 - Configuration6 to 4 Tunneling (Stateful)Select 6 to 4 from the drop-down menu.Enter the IPv6 settings supplied by your Internet provider (ISP). Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateful (DHCPv6) or Stateless. Refer to the next page for Stateless.Enter the start IPv6 Address for the DHCPv6 range for your local computers.Enter the end IPv6 Address for the DHCPv6 range for your local computers.Enter the IPv6 Address Lifetime (in minutes).My IPv6 Connection:6 to 4 Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:IPv6 Address Range Start:IPv6 Address Range End:IPv6 Address Lifetime:
60D-Link DIR-615 User ManualSection 3 - Configuration6 to 4 Tunneling (Stateless)Select 6 to 4 from the drop-down menu.Enter the IPv6 settings supplied by your Internet provider (ISP). Enter the primary and secondary DNS server addresses. Enter the LAN (local) IPv6 address for the router. Displays the Router’s LAN Link-Local Address.Check to enable the Autoconfiguration feature.Select Stateless. Refer to the previous page for Stateful.Enter the Router Advertisement Lifetime (in minutes).My IPv6 Connection:6 to 4 Settings:Primary/Secondary DNS Address:LAN IPv6 Address:LAN Link-Local Address:Enable Autoconfiguration:Autoconfiguration Type:Router Advertisement Lifetime:

Navigation menu