Users Manual 1 of 2
User’s Guide H950V(B19AC) TFT-LCD Monitor Table of Contents Regulatory Information ...............................................................................................................................2 Introduction Package ........................................................................................................................................................ 3 The range of control Angle ............................................................................................................................3 Connection to Signal Source .........................................................................................................................4 Controls Front panel ................................................................................................................................................... 5 Functions .......................................................................................................................................................5 Adjusting OSD(PC MODE) ............................................................................................................................6 Adjusting OSD(CVBS, S-VIDEO MODE) .................................................................................................... 11 Caution .........................................................................................................................................................16 Power Management Feature .................................................................................................................... 17 Standard Signal Table ............................................................................................................................... 18 Specifications ............................................................................................................................................. 19 Pin assignment table D-Sub Mini 15pin connector ........................................................................... 20 Troubleshooting ......................................................................................................................................... 21 TFT-LCD Monitor Regulatory Information - FCC Information This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause unacceptable interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced Radio/TV technician for help. Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. - Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. - Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. - Energy Star As an ENERGY STAR partner, Hansol LCD Inc. has determined that this product meets energy Star guidelines for energy efficiency. Notice The information contained in this document is subject to change without notice. TFT-LCD Monitor Introduction - Package Congratulations on your purchase of this top quality color monitor! The items illustrated below are contained in the carton. First, be sure that your carton includes all of them. If any items are missing or damaged, please contact your local dealer or supplier. UK LCD Monitor Signal Cable U.S.A/ Canada Stereo Cable (Option) AC Power Cable Warranty Card - The range of control Angle CD (User’s Guide & etc) Europe Australia Korea How to Adjust the Stand ▲ Forward 5° ▲ Default ▲ Backward 33° TFT-LCD Monitor Introduction - Connection to Basic Connection Signal Source ① Port for AC power cable. ② Port for BNC output. ③ Port for BNC input. ④ Port for S-VHS input. ⑤ Port for Audio input. ⑥ Kensington Lock. ⑦ Port for signal cable from signal source. ① ② ③ ④⑤ ⑥ ⑦1. Use 220V or 110 V. (Free Voltage) 2. Connect monitor and Signal Source via Signal cable. 3. Power on the monitor and computer. 4. Connection is finished. General For Macintosh Adapter for Macintosh(Optional) Refer to the table on the rear side of the optional Macintosh adapter and adjust DIP switch by the resolution. TFT-LCD Monitor Controls - Front panel SOURCE BUTTON VOL/MUTE BUTTON / + BUTTON MENU/EXIT BUTTON / – BUTTON SELECT/AUTO BUTTON POWER BUTTON (Power indicating LED) - Functions Power button Power button is located in the lower center of the Front Bezel. You can push the button to trun on/off the power. Power Indicating LED Dark : Power off Green : Normal mode Green blinking : DPMS mode or Check Signal Cable mode. On Screen Display(OSD) Function Button OSD buttons on the front of bezel perform the following functions. SOURCE : Monitor displays source of the signal in order (PC → CVBS → S-VHS) MENU/EXIT : Press this button to display menus.If you press this button when OSD is displayed, you can switch display to the previous menu and exit menu. SELECT/AUTO : Press this button, when OSD is not displayed, to perform automatic setting.(only PC Mode.) When OSD is displayed, you can select icons. POWER : Power button. +/ ,–/ : By pressing these button when OSD is displayed, you can move cursor into the menus which you want. After press the SELECT button, you can change gauge level or select submenus. When OSD is not displayed, you can adjust brightness or contrast. VOLUME/MUTE : Press this button for volume control. When Control is displayed, you can control mute by pressing this button. TFT-LCD Monitor Controls - Adjusting OSD (PC MODE) Brightness / Contrast MENU – + SELECT 1. Press the MENU button to access main menu. 2. Use – , + to move Brightness / Contrast ICON. 3. Press SELECT button into the submenu. Brightness – + SELECT – + 1. Use – , + to move Brightness ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust the brightness of the screen. Contrast – + SELECT – + 1. Use – , + to move Contrast ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust the contrast of the screen. Clock Phase MENU – + SELECT 1. Press the MENU button to access main menu. 2. Use – , + to move CLOCK PHASE ICON. 3. Press SELECT button into the submenu. TFT-LCD Monitor Horizontal Position – + SELECT – + 1. Use – , + to move H-Position ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust display left or right. According to the characteristic of video card, control range can be changed. Vertical Position – + SELECT – + 1. Use – , + to move V-Position ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust display upward or downward. According to the characteristic of video card, control range can be changed. Phase – + SELECT – + 1. Press – , + to move Phase ICON. 2. Use SELECT button to select it. 3. Use – , + to correct fine trembling or Video noise. Clock – + SELECT – + 1. Use – , + to move Clock ICON. 2. Press SELECT button to select it. 3. Press – or + to remove vertical noise. (Adjusting clock phase is required after the adjustment of clock.) TFT-LCD Monitor Color MENU – + SELECT 1. Press MENU button to access main menu. 2. Use – , + to move Color ICON. 3. Press SELECT button into the submenu. Preset Color – + MENU 1. Use – , + to select the Mode 1, and Mode 2. 2. Press the Menu button to return previous state. 9300K : Slighty Bluish white. 6500K : Slighty Reddish white. User Color – + SELECT – + MENU 1. Use – , + to move Color ICON. 2. Press SELECT button to select it. 3. Use – , + to increase or decrease each color. OSD MENU – + SELECT 1. Press MENU button to access main menu. 2. Use – , + to move OSD ICON 3. Press SELECT button into the submenu. TFT-LCD Monitor OSD H-Position – + SELECT – + 1. Use – , + to move OSD H-position ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust OSD Left or right. OSD V-Position – + SELECT – + 1. Use – , + to move OSD V-position ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust OSD upward or downward. OSD Time – + SELECT – + 1. Use – , + to move OSD Time ICON. 2. Press SELECT button to select it. 3. Use – , + to adjust OSD display time. 4. Press menu button to return main menu. Special MENU – + SELECT 1. Press the MENU button to access main menu. 2. Use – , + to move Special ICON. 3. Press SELECT button into the submenu. TFT-LCD Monitor Language MENU – + SELECT – + 1. Use – , + to move Language ICON. 2. Press SELECT button to select it. 3. Use – , + to select language. Factory Reset – + SELECT 1. Use – , + to move the Factory Reset ICON. 2. Press SELECT button to return to default setting. Information MENU – + SELECT 1. Use – , + to move the information ICON. 2. Press SELECT button to select it. According to the characteristic of video card, display information can be incorrect. ※ You can know display information. Sound MENU – + SELECT 1. Use – , + to decrease or increase volume level. 2. Press SELECT button to select it. 3. Use – , + to control volume. 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2005:10:17 17:43:58+09:00 Create Date : 2005:10:17 17:43:43+09:00 Title : model.book Author :EXIF Metadata provided by EXIF.toolsCreator : FrameMaker 6.0 Producer : Acrobat Distiller 5.0 (Windows) Page Count : 10 Mod Date : 2005:10:17 17:43:58+09:00 Creation Date : 2005:10:17 17:43:43+09:00 Metadata Date : 2005:10:17 17:43:58+09:00 Has XFA : No