D and T FS-4201C 42" LCD Monitor User Manual ATT E MANUAL

D&T; Inc. 42" LCD Monitor ATT E MANUAL

Manual

FCC ID : FS-L4201C HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD. SAN 136-1, AMI-RI, BUBAL-EUP, ICHEON-SI, KYOUNGKI-DO, 467-701, KOREA TEL:+82 31 639 8517 FAX:+82 31 639 8525 www.hct.co.kr Report No. : HCT-F07-0101 ATTACHMENT E. - USER’S MANUAL -
Printed in KoreaPart No. 942667020001 - 01TFT-LCD Color Monitor FS-L4201CUser ManualEnglishwww.tandberg.net
Parts 3Connection to Signal Source 4Out Drawing of product 6Name and Function 7Power Management Feature 8Adjusting OSD 10Standard Signal Table 12Pin assignment table of signal connector 13Specification 15Troubleshooting 16Warning 18INFORMATION TO USER :This equipment has been tested and found to comply with the limits of aClass B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses andcan radiate radio frequency energy and,if not installed and used in accor-dance with the instructions, may cause harmful interference to radio commu-nications. However, there is no guarantee that interference will not occur in a particularinstallation; if this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment offand on, the user is encouraged to try to crrent the interference by one or moreof the fllowing measures:1. Reorient/Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit differencefrom that to which the recerver is connected.4. Consult the dealer or an experienced radio/TV technician for help.CAUTIONChanges or modifications not expressly approved by themanufacturer responsible for compliance could void the user's authority to operate the equipmentTable of Contents
Basic ConnectionAC Inlet.AC on/ off SwitchRCA Coaxial S/PDIF Audio input9 Pin D-Sub connector for Speaker Out24 Pin DVI Connector for Digital TMDS15 Pin D-Sub connector for Analog RGB User's Manual 42 " LCD MonitorPartsConnection to Signal Source LCD MONITOR User s Manual3LCD MONITOR User s Manual4This monitor do not provide any other accessaries and peripheral devices (ex,speaker and signal cable) because the Tandberg's reguest.
1. Use 220 V or 110 V. (Free Voltage)2. Connect monitor and Signal Source via Signal cable3. Power on the monitor and computer.4. Connection is finished.D-Sub Analog(Data in)DVI Digital< Power source connection > < Signal cable connection> Coaxial S/PDIF InputAudio amp OutputO ut Drawing of productLCD MONITOR User s Manual5LCD MONITOR User s Manual6AC InletAC on/off swith
LCD MONITOR User s Manual7LCD MONITOR User s Manual8Front side+ BUTTON-BUTTONSOURCE BUTTONMENUBUTTONOK BUTTONBUTTONBUTTONName and Function Rear sideRemote signal windowPower indicating LEDPower Management FeaturePower management system of this monitor can not be corresponded with VESA DPMS when the display video signal is none because thespecific character of Tandberg systemStatus LED Sign Power ConsumptionNormal mode Green on Normal PowerStand by mode Red on 20W or Below
English - 109 - English LCD MONITOR User s Manual9LCD MONITOR User s Manual10Remote signal wirdowThis window is for the receiving signal from remote controllerDo not hide this window.Power Indicating LEDGreen : Normal modeRED : Standby modeOn-Screen Display (OSD) Function ButtonMENU: With OSD deactivated, Activated to OSD menuWith OSD activated, Exit from main menu or sub menu.OK : With OSD deactivated, you can see the kind of displayed source on the right bottom side of the screen.With OSD activated, Enter sub menu and change each sub menu itemUP( : With OSD deactivated, Hot key of the brightness control and increases the brightness.With OSD activated, move the cursor upward.DOWN( : With OSD deactivated, Hot key of the brightness control and decreases the brightness.With OSD activated, move the cursor downward.PLUS( : With OSD deactivated, Hot key of the contrast control and increasesthe contrast.With OSD activated, enter sub menu and increases the adjustment of the selected function.MINUS(-) : With OSD deactivated, Hot key of the contrast control and decreases the contrast.With OSD activated, decreases the adjustment of the selected function.SOURCE : For the extra function, normally no need to use this button.FunctionsCOLOR TEMP1. MODEChange the Color mode ( 6500, 7200, 9300, USER )2. REDRed balance(Only Working with USER mode) (Range: 0~100)3. GREENGreen balance(Only Working with USER mode) (Range: 0~100)4. BLUEBlue balance(Only Working with USER mode) (Range: 0~100)Adjusting OSD PICTURE1. BRIGHTNESSIncrease or decrease the brightness(Range: 0~100)2. CONTRASTIncrease or decrease the Contrast(Range: 0~100)3. BACK LIGHTIncrease or decrease theCCFL back light luminance(Range: 0~100)
LCD MONITOR User s Manual11 LCD MONITOR User s Manual12(640 X 480)(640 X 480)(640 X 480)(640 X 480)(800 X 600)(800 X 600)(800 X 600)(800 X 600)(800 X 600)(800 X 600)(1024 X 768)(1024 X 768)(1024 X 768)(1280 X 768)(1280 X 720)(1280 X 720)(1280 X 1024)(1366 X768)31.537.937.543.331.535.137.948.146.953.748.456.56047.737.5456448.3260727585505660727585607075605060606025.17531.531.53635.437536405049.556.25657578.7579.574.2574.2510887.75ResolutionHorizontal Frequency (KHz)Vertical Frequency(Hz) Clock Frequency(MHz)PC Supported ModeSETUP1. IMAGE SIZEChange the image size (Scaling mode)(Full,Fill aspect, 1:1)2. SHARPNESSSet the sharpness of image(Softest,Softest,Normal,Sharp,Sharpest)3. RESET SETTINGSChanges all OSD values to factory outgoing status.IMAGE1. LANGUAGEChange the OSD languageorean,English,French,Spanish,German,Chinese,Japanese,Italian 2. OSD COLORAdjust the OSD back ground from white opaque to half translucent.3. OSD POSITIONChange the OSD position (9 postions)4. DURATIONAdjust OSD display time(5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)Standard Signal Table
LCD MONITOR User s Manual13 LCD MONITOR User s Manual1415699 Pin D-subPin No. Assignment 1 Ground2 Speaker ID43 Speaker ID34 Speaker ID25 Speaker ID16 Speaker Out Left-7 Speaker Out Left+8 Speaker Out Right-9 Speaker Out Right1511 1561015pin D-SubPin No. Assignment Pin No. Assignment 1 Red 9 NC2 Green 10 Ground-Sync3 Blue 11 Ground4 Ground 12 DDC Data5 DDC 5V Standby 13 H.SyncCable Connection check 14 V.Sync6 Ground-Red 15 DDC Clock7 Ground-Green 8 Ground-Blue 1817 2491624 Pin DVI-D21RCAPin No. Assignment Pin No. Assignment 1 T.M.D.S. Data2- 13 No Connect2 T.M.D.S. Data2+ 14 No Connect3 T.M.D.S. Data2 Shield 15 Cable Connection check4 No Connect 16 Hot Plug Detect5 No Connect 17 T.M.D.S. Data0-6 DDC Clock 18 T.M.D.S. Data0+7 DDC Data 19 T.M.D.S. Data0 Shield 8 No Connect 20 No Connect9 T.M.D.S. Data1- 21 No Connect10 T.M.D.S. Data1+ 22 Cable Connection check11 T.M.D.S. Data1 Shield 23 T.M.D.S. Clock+12 No Connect 24 T.M.D.S. Clock-Pin No. Assignment 1 Coaxial S/PDIF audio signal2 Ground Pin assignment table of signal connector
LCD MONITOR User s Manual15 LCD MONITOR User s Manual16Adjust COLOR at User Mode in OSD Color Temp Menu.Color is irregular.Check the power connection. (Refer to page 5)Power LED is dark.No picture.Power LED is Red Check the signal cable or signal Source.(Refer to page 5)Screen is not clear.Check the resolution and frequency of computer and video card, and set up again.Refer to the current monitor mode and standard signal mode table.(Refer to page 12)Display is unstable andtrembling.Remove and check attaches to the signal line(Video extension cable and others) and switch on.TroubleshootingType a-si TFT Active matrixScreen Size 106.7cm (Diagonal)Maximum Resolution1366 X 768@ 60 HzPixel Range0.681(H) mm X 0.227(V) mmDisplay Colors 16.7M (RGB 8-bit data)Contrast Ratio 1000 : 1Viewing Angle 89° / 89° / 89° / 89°Response Time 10 msecLuminance 500 cd/mHorizontal Frequency 91kHz (Max.)Vertical Frequency 85Hz (Max.)Maximum 300Wstandby Mode Under 20WSOURCE, -,+, Video Analog RGB DVI DigitalAudio S/PDIF (Coaxial)Video VGA,SVGA,XGA,WXGAAudio IEC-958 S/PDIF 32kHz,44.1kHz,48kHz,96kHzSafety Standard UL,C-TICK,EK,CCCEMI CE,MIC,BSMI,FCCSize and Weight1022 615 98/ 29kgLCDPanelSynchronizationModel FS-L4201CInputSignalCompatibilityPower ConsumptionControl keyRear sideSafetyStandard& EMIDimensionSpecification
LCD MONITOR User s Manual17 LCD MONITOR User s Manual18WarningTo prevent damage or loss, please read this warning carefully.When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short.To prevent electric shock, do not connect/dis-connect the plug with wet hand.To prevent fire, do not connect a large number ofequipments in a single line.To prevent fire and electric shock, pull out the plug incase of thunder and lightening.To prevent fire and electric shock, do not try to takethe monitor apart or repair it yourself. Contact yourlocal service station or customer service center forinspection, modification or repair.If you see smoke or smell something burning, stopusing the unit, switch off the power, pull out the plug,and then contact your local service station.Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.(Refer to page 5)Double images or'ghosts'.Adjust COLOR at User Mode in OSD Color Temp Menu.Picture is dark.
19 - English

Navigation menu