D and T FS-A4206 42" Color TFT LCD Monitor (Model: FS-A4206C) User Manual

D&T; Inc. 42" Color TFT LCD Monitor (Model: FS-A4206C) Users Manual

Contents

Users Manual

LCD MONITORUser’s GuideFS-A4206F/FS-A4206C
INFORMATION TO USE :This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against interference. This monitor can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications equipment. There is no guarantee that interference will not occur in a particular installation. If this gpequipment is found to cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by carrying out one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the distance between the color monitor and the subject of finterference.3. Plug the monitor into a outlet on a different electrical circuit than that to which the subject of interference is connected.4. Consult the dealer or an experienced radio/TV technician for help.CAUTIONModifications not expressly approved by the manufacturer responsible for compliance could void the warranty of the product. Attempts by the user to disassemble or modify the monitor will void the warranty.General Specification
Table of contents1. Part--------------------------------------------------------------------------------------------------- 12. Product drawing----------------------------------------------------------------------------------- 23. Monitor Connection----------------------------------------------------------------------------- 34. Function key--------------------------------------------------------------------------------------- 55. OSD adjust --------------------------------------------------------------------------------------- 76. Standard signal table ---------------------------------------------------------------------------- 97. Signal Connector pin assignments ----------------------------------------------------------- 108. Specification ------------------------------------------------------------------------------------- 129. Safety instructions ----------------------------------------------------------------------------- 14General Specification
PartsLCD MONITOR42” LCD MonitorUSER MANUAL AC power extensionCable(Option)Serial Cable(Option)DVI-HDMI CableGeneral Specification (Option)1
LCD MONITORProduct drawinggUnit : mm2
LCD MONITORMonitor Connection●FS-A4206C 1AC / ff S h1.AC on/off Switch2. AC Inlet.3. 29 Pin DVI in connector4. 29 Pin DVI Out connector5. 15 Pin VGA connector 6. 9 Pin RS-232 connector●FS-A4206F 1. AC on/off Switch2. AC Inlet.3. 29 Pin DVI in connector4. 9 Pin RS-232 connector3
LCD MONITORPower source connection Signal cable connectiongTo the AC inlet connector●DVI In,Out put●AC InputTo the AC inlet connector●VGA Analog●RS-232●AC on/off switch1. Use 220V or 110V.2. Connect the DVI Cable to the monitor.3. Power on the monitor.4. Done.General Specification 4
LCD MONITORFunction keyyAn 8 button keypad, located in rear side of the display, allows the user to make adjustments to various display parameters using the On Screen Display(OSD) system. ●Indicate the power status and input signal statusppgNormal mode : Always green Standby mode : Blinking green(ex, No signal) Sleep mode : Always redNote 1 : LED normal and off mode sign can be changed according to the requirement of the customerwhether normal mode green is on or offNote 2 : The main AC power switch, on the back panel, should be in the ON position.Th DC b i d h iThe DC power button is used to turn on the monitor●On-Screen Display (OSD) Function Button 1. POWER : Monitor power on and off 2. MENU : With OSD deactivated, Activated OSD menu.With OSD activated Exit from main menu or sub menu With OSD activated, Exit from main menu or sub menu. 3. UP (▲) : With OSD deactivated, Hot key of the brightness control and increases the brightness.With OSD activated, move the cursor upward. 4. DOWN (▼) : With OSD deactivated, Hot key of the brightness control and decreases the brightness. With OSD activated, move the cursor downward. General Specification 5
5. PLUS(+) : With OSD deactivated, Hot key of the contrast control and increases the contrast.With OSD activated, enter sub menu and increases the adjustment of the selected.LCD MONITORWith OSD activated, enter sub menu and increases the adjustment of the selected.6. MINUS(-) : With OSD deactivated, Hot key of the contrast control and decreases the contrast.With OSD activated, decreases the adjustment of the selected function. 7.INPUT : With OSD deactivated, you can see the kind of displayed source on lower right of the screen. 8. PIP : Picture in picture function will be activated and change the picture layout.(This function is provided for FS-A4206C Model only)6
LCD MONITOROSD adjustjPICTUREBRIGHTNESSIncrease or decrease the brightness. (Range : 0 ~ 100) CONTRASTIncrease or decrease the contrast. (Range : 0 ~ 100)BACKLIGHTIncrease or decrease the backlight. (Range : 0 ~ 100)COLOR TEMPMODEChange the color temperature mode : 6500K, 7200K, 9300K, USERWhen USER is selected, a sub-menu displays allowing the user to adjust the RED, GREEN or BLUE balance.user to adjust the RED, GREEN or BLUE balance.REDRed balance – Only works on the USER mode. (Range : 0 ~ 100)GREENGreen balance – Only works on the USER mode. (Range : 0 ~ 100)BLUEGeneral Specification BLUEBlue balance – Only works on the USER mode. (Range : 0 ~ 100)7
IMAGELCD MONITORIMAGEChange the image size : FILL ASPECT, FILL ALL, ONE TO ONESHARPNESSSet the sharpness of the image.(SOFTEST, SOFT, NORMAL, SHARP, SHARPEST)RESET SETTINGSRestore all the OSD values to factory out-going status.UNIT IDChange the unit identification. (Range : 1 ~ 9)OSD SETUPLANGUAGEChange the OSD Language. (8 languages – English, German, French, Spanish, Italian, Chinese, Japanese, Korean)OSD COLORAdjust transparency of OSD background. (Range : 0 ~ 100)OSD POSITIONChange the OSD position.DURATIONAdjust OSD display time.(5, 10, 20, 30, 60, 90, 120, 180, 240 seconds)General Specification 8
Standard signal tableLCD MONITORResolution Horizontal Frequency(KHz) Vertical Frequency(Hz)Clock Frequency(MHz)640x480@60Hz 31.469 59.940 25.175gPC Supported mode@800x600@50Hz 31.500 50.000 35.4375800x600@50Hz 37.879 60.317 40.000800x600@75Hz 46.875 75.000 49.5001024x768@60Hz 48.363 60.004 65.0001280 720@50H37 50050 00074 2501280x720@50Hz37.50050.00074.2501280x720@60Hz 45.000 60.000 74.2501280x720@100Hz 75.000 100.000 148.5001280x720@120Hz 90.000 120.000 148.5001280x1024@60Hz 63.981 60.020 148.5001280x768@60Hz 47.776 59.870 79.5001360x768@60Hz 47.712 60.015 85.5001366x768@60Hz 48.320 59.803 87.7501400x1050@60Hz 65.317 59.979 121.7511680x1050@60Hz 64.674 59.883 119.0001600x1200@60Hz 75.000 60.000 162.0001920x1080@24Hz 27.000 24.000 74.2501920x1080@25Hz 28.125 25.000 74.2501920x1080@30Hz 33.750 30.000 74.2501920x1080@50Hz 56.250 50.000 148.5001920x1080@60Hz 67.500 60.000 148.5001920x1200@60Hz 74.038 59.950 154.000General Specification 9
Signal Connector pin assignmentsLCD MONITORPin No. Assignment Pin No. Assignment1 TMDS Data2+ 13 No ConnectionDVI In,Out (DVI-I 29Pin)gpg2 TMDS Data2+ 14 +5V Power3 TMDS Data2 Shield15 Cable connection check4 No Connection 16 Hot Plug Detect5 No Connection 17 TMDS Data0-6 DDC Clock 18 TMDS Data0+7 DDC Data 19 TMDS Data0 Shield8 No Connection 20 No Connection9 TMDS Data1- 21 No Connection10 TMDS Data1+ 22 TMDS Clock Shield11 TMDS Data1 Shield23 TMDS Clock+12 No Connection 24 TMDS Clock-RS-232 (D-SUB 9Pin,female)Pin No.Assignment Pin No.Assignment1 Test pin1(Note) 6 No Connection2 RS-232 RXD Input7 Test pin2(Note)p3 RS-232 TXD Input8 Test pin3(Note)4 No Connection 9 No Connection5 GroundGeneral Specification Note : Please keep these pins to no connection.10
VGA (DSUB 15Pi )LCD MONITORPin No. Assignment Pin No. Assignment1 Red 9 No Connection2 Green 10 Ground-Sync3Bl11GdVGA (D-SUB 15Pin)3Blue11Ground4 Ground 12 DDC Data5 DDC 5V StandbyCable Connection check13 H.Sync6GdRd14VS6Ground-Red14V.Sync7 Ground-Green 15 DDC Clock8 Ground-BlurGeneral Specification 11
SpecificationLCD MONITORModel FS-A4206FType A-si TFT Active matrixDisplay area 930.4(H) mm X 523.26(V) mmpLCD PANELMaximum Resolution 1920X1080@120HzPixel pitch 0.4845(H)mm X 0.4845(V)mmDisplay colors 1073.7M (RGB 10-bit data)Contrast Ratio(Typ.) 4000:1Viewing Angle(Typ.) 89/89/89/89Response Time(Typ.) 5msLuminance(Typ.) 500cd/m2Horizontal Frequency135.6 KHzSynchronizationHorizontal Frequency135.6 KHzVertical Frequency 120 HzPower ConsumptionMaximum 120WStandby Mode Under 0.5WPowerAC 100240V~5060Hz 1 2A MaxPowerAC 100-240V~50-60Hz 1.2A MaxApproval Marks Approval Mark UL, FCC, Mx CoC, AR-S, CE, Gost-R, SASO, CCC,South Africa, KC BSMI, Singapore safety, C-Tick, CBEnergy Efficiency China energy label, E-StandbyDimension Size and weight 1002.5X40X595 /17Kg(21Kg)General Specification 12
LCD MONITORModel FS-A4206CType A-si TFT Active matrixDisplay area 930.4(H) mm X 523.26(V) mmLCD PANELMaximum Resolution 1920X1080@120HzPixel pitch 0.4845(H)mm X 0.4845(V)mmDisplay colors 1073.7M (RGB 10-bit data)Contrast Ratio(Typ.) 4000:1Viewing Angle(Typ.) 89/89/89/89Response Time(Typ.) 5msLuminance(Typ.) 500cd/m2Horizontal Frequency135.6 KHzSynchronizationHorizontal Frequency135.6 KHzVertical Frequency 120 HzPower ConsumptionMaximum 120WStandby Mode Under 0.5WPowerAC 100240V~5060Hz 1 2A MaxPowerAC 100-240V~50-60Hz 1.2A MaxApproval Marks Approval Mark UL, FCC, CBDimension Size and weight 1002.5X40X595 /17Kg(21Kg)General Specification 13
Safety instructionsLCD MONITORyOperator Safety InstructionsFor your safety, please read these safety instructions completely before you connect the equipment to the power source. The information in this summary is intended for operators.Carefully observe all warnings, precautions and instructions both on the apparatus and in these operating instructionsoperating instructions.Retain this manual for future reference.Water and MoistureDo not operate the apparatus under or near water - for example near a bathtub, kitchen sink, or laundry tub, in a wet basement, near a swimming pool or in other areas with high humidity.Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations.gDo not touch the product with wet hands.CleaningUnplug the apparatus from communication lines, mains power-outlet or any power sourcebefore cleaning or polishing. Do not use liquid cleaners or aerosol cleaners. Use a lint-free cloth lightly moistened with water for cleaning the exterior of the apparatus. VentilationDo not block any of the ventilation openings of the apparatus. Never cover the slots and openings with a cloth or other material. Never install the apparatus near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place the product in direct sunlight or close to a surface directly heated by the sun.LightningNever use this apparatus, or connect/disconnect communication cables or power cables duringlightning storms.DustDo not operate the apparatus in areas with high concentration of dustVibrationDo not operate the apparatus in areas with vibration or place it on an unstable surface.General Specification 14
P C ti d Hd VltLCD MONITORPower Connection and Hazardous VoltageThe product may have hazardous voltage inside. Never attempt to open this product, or any peripherals connected to the product, where this action requires a tool.This product should always be powered from an earthed power outlet.Never connect attached power supply cord to other products.In case any parts of the product has visual damage never attempt to connect mains power, or any other power source, before consulting service personnelThe plug connecting the power cord to the product serves as the main disconnect device for The plug connecting the power cord to the product serves as the main disconnect device for this equipment. The power cord must always be easily accessible.Route the power cord so as to avoid it being walked on or pinched by items placed upon or against it. Pay particular attention to the plugs, receptacles and the point where the cord exits from the apparatus.Do not tug the power cord.If the provided plug does not fit into your outlet, consult an electrician.Never install cables, or any peripherals, without first unplugging the device from it's power source.ServicingDo not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel.Unplug the apparatus from its power source and refer servicing to qualified personnel under thefollowing conditions:following conditions:If the power cord or plug is damaged or frayed.If liquid has been spilled into the apparatus.If objects have fallen into the apparatus.If the apparatus has been exposed to rain or moisture If the apparatus has been subjected to excessive shock by being dropped.If the cabinet has been damaged.If the apparatus seems to be overheated.ppIf the apparatus emits smoke or abnormal odor.If the apparatus fails to operate in accordance with the operating instructionsAccessoriesUse only accessories specified by the manufacturer, or sold with the apparatus. General Specification 15
WarningLCD MONITORWhen connecting to/disconnecting from a power outlet, push/pull on the plug itself. Never pull the cord, in order to prevent fire caused by a short.gIn order to prevent electric shock, do not connect/disconnect the plug with wet or moist hands.If you see smoke or smell something burning, stop using the unit, switch off the power, pull out the plug, and then contact your local service station.To prevent fire, do not connect a large number of equipments in a single line.To prevent fire and electric shock, pull out the plug in case of thunder and lightning.To prevent fire and electric shock, do not try to take the monitor apart or repair it yourself. Contact your local service station or customer service center for inspection, modification or repair.General Specification 16

Navigation menu