D and T FS-A4206 42" Color TFT LCD Monitor (Model: FS-A4206C) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1635409
Application ID	pmFSXZuOXk0unErju1lRWQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28kB (350039 bits)
Date Submitted	2012-02-13 00:00:00
Date Available	2012-03-09 00:00:00
Creation Date	2011-12-13 09:51:01
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2011-12-13 09:51:01
Document Title	Microsoft PowerPoint - FS-A4206F_4206C User manual(EN) [호환 모드]
Document Creator	PScript5.dll Version 5.2
Document Author:	Sens

LCD MONITOR
User’s Guide
FS-A4206F/FS-A4206C
INFORMATION TO USE :
This equipment has been tested and found to comply with the limits of a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against interference. This
monitor can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, it may interfere with other radio communications equipment.
There is no gguarantee that interference will not occur in a particular
installation. If this
equipment is found to cause harmful interference to radio or television reception, the
user is encouraged to try to correct the interference by carrying out one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the color monitor and the subject of
interference.
3. Plug the monitor into a outlet on a different electrical circuit than that to which
the subject of interference is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Modifications not expressly approved by the manufacturer responsible for compliance
could void the warranty of the product. Attempts by the user to disassemble or modify
the monitor will void the warranty.
General Specification
Table of contents
1. Part--------------------------------------------------------------------------------------------------- 1
2. Product drawing----------------------------------------------------------------------------------- 2
3. Monitor Connection----------------------------------------------------------------------------- 3
4. Function key--------------------------------------------------------------------------------------- 5
5. OSD adjust --------------------------------------------------------------------------------------- 7
6. Standard signal table ---------------------------------------------------------------------------- 9
7. Signal Connector pin assignments ----------------------------------------------------------- 10
8. Specification ------------------------------------------------------------------------------------- 12
9. Safety instructions ----------------------------------------------------------------------------- 14
General Specification
LCD MONITOR
Parts
42” LCD Monitor
USER MANUAL
DVI-HDMI Cable
(Option)
General Specification
AC power extension
Cable(Option)
Serial Cable
(Option)
LCD MONITOR
Product drawing
Unit : mm
LCD MONITOR
Monitor Connection
● FS-A4206C
1.
2.
3.
4.
5.
6.
AC on/off
/ ff Switch
AC Inlet.
29 Pin DVI in connector
29 Pin DVI Out connector
15 Pin VGA connector
9 Pin RS-232 connector
● FS-A4206F
1.
2.
3.
4.
AC on/off Switch
AC Inlet.
29 Pin DVI in connector
9 Pin RS-232 connector
LCD MONITOR
Power source connection
cable connection
Signal
● DVI In,Out put
To the AC inlet connector
● AC Input
● VGA Analog
● RS-232
● AC on/off switch
1.
2.
3.
4.
Use 220V or 110V.
Connect the DVI Cable to the monitor.
Power on the monitor.
Done.
General Specification
LCD MONITOR
Function key
An 8 button keypad, located in rear side of the display, allows the user to
make adjustments to various display parameters using the On Screen Display(OSD) system.
power status and input
p signal
g status
● Indicate the p
Normal mode : Always green
Standby mode : Blinking green(ex, No signal)
Sleep mode : Always red
Note 1 : LED normal and off mode sign can be changed according to the requirement of the customer
whether normal mode green is on or off
Note 2 : The main AC power switch, on the back panel, should be in the ON position.
Th DC power bbutton iis used
The
d to turn on the
h monitor
● On-Screen Display (OSD) Function Button
1. POWER : Monitor power on and off
2. MENU : With OSD deactivated, Activated OSD menu.
With OSD activated,
activated Exit from main menu or sub menu.
menu
3. UP (▲) : With OSD deactivated, Hot key of the brightness control and increases the brightness.
With OSD activated, move the cursor upward.
4. DOWN (▼) : With OSD deactivated, Hot key of the brightness control and decreases the
brightness.
With OSD activated, move the cursor downward.
General Specification
LCD MONITOR
5. PLUS(+) : With OSD deactivated, Hot key of the contrast control and increases the contrast.
With OSD activated, enter sub menu and increases the adjustment of the selected.
6. MINUS(-) : With OSD deactivated, Hot key of the contrast control and decreases the contrast.
With OSD activated, decreases the adjustment of the selected function.
7.INPUT : With OSD deactivated, you can see the kind of displayed source on lower right of the
screen.
8. PIP : Picture in picture function will be activated and change the picture layout.
(This function is provided for FS-A4206C Model only)
LCD MONITOR
OSD adjust
PICTURE
BRIGHTNESS
Increase or decrease the brightness. (Range : 0 ~ 100)
CONTRAST
Increase or decrease the contrast. (Range : 0 ~ 100)
BACKLIGHT
Increase or decrease the backlight. (Range : 0 ~ 100)
COLOR TEMP
MODE
Change the color temperature mode : 6500K, 7200K,
9300K, USER
When USER is selected, a sub-menu displays allowing the
user to adjust the RED, GREEN or BLUE balance.
RED
Red balance – Only works on the USER mode. (Range : 0 ~ 100)
GREEN
Green balance – Only works on the USER mode. (Range : 0 ~ 100)
BLUE
Blue balance – Only works on the USER mode. (Range : 0 ~ 100)
General Specification
LCD MONITOR
IMAGE
IMAGE
Change the image size : FILL ASPECT, FILL ALL, ONE TO ONE
SHARPNESS
Set the sharpness of the image.
(SOFTEST, SOFT, NORMAL, SHARP, SHARPEST)
RESET SETTINGS
Restore all the OSD values to factory out-going status.
UNIT ID
Change the unit identification. (Range : 1 ~ 9)
OSD SETUP
LANGUAGE
Change the OSD Language. (8 languages – English, German,
French, Spanish, Italian, Chinese, Japanese, Korean)
OSD COLOR
Adjust transparency of OSD background. (Range : 0 ~ 100)
OSD POSITION
Change the OSD position.
DURATION
Adjust OSD display time.(5, 10, 20, 30, 60, 90, 120, 180, 240
seconds)
General Specification
LCD MONITOR
Standard signal
table
PC Supported mode
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Clock Frequency(MHz)
640x480@60Hz
31.469
59.940
25.175
800x600@50Hz
31.500
50.000
35.4375
800x600@50Hz
37.879
60.317
40.000
800x600@75Hz
46.875
75.000
49.500
1024x768@60Hz
48.363
60.004
65.000
1280 720@50H
1280x720@50Hz
37 500
37.500
50 000
50.000
74 250
74.250
1280x720@60Hz
45.000
60.000
74.250
1280x720@100Hz
75.000
100.000
148.500
1280x720@120Hz
90.000
120.000
148.500
1280x1024@60Hz
63.981
60.020
148.500
1280x768@60Hz
47.776
59.870
79.500
1360x768@60Hz
47.712
60.015
85.500
1366x768@60Hz
48.320
59.803
87.750
1400x1050@60Hz
65.317
59.979
121.751
1680x1050@60Hz
64.674
59.883
119.000
1600x1200@60Hz
75.000
60.000
162.000
1920x1080@24Hz
27.000
24.000
74.250
1920x1080@25Hz
28.125
25.000
74.250
1920x1080@30Hz
33.750
30.000
74.250
1920x1080@50Hz
56.250
50.000
148.500
1920x1080@60Hz
67.500
60.000
148.500
1920x1200@60Hz
74.038
59.950
154.000
General Specification
LCD MONITOR
Signal
Connector pin
p assignments
DVI In,Out (DVI-I 29Pin)
Pin No.
Assignment
Pin No.
Assignment
TMDS Data2+
13
No Connection
TMDS Data2+
14
+5V Power
TMDS Data2
Shield
15
Cable connection check
No Connection
16
Hot Plug Detect
No Connection
17
TMDS Data0-
DDC Clock
18
TMDS Data0+
DDC Data
19
TMDS Data0 Shield
No Connection
20
No Connection
TMDS Data1-
21
No Connection
10
TMDS Data1+
22
TMDS Clock Shield
11
TMDS Data1
Shield
23
TMDS Clock+
12
No Connection
24
TMDS Clock-
RS-232 (D-SUB 9Pin,female)
Pin
No.
Assignment
Pin
No.
Assignment
Test pin1(Note)
No Connection
RS-232 RXD
Input
Test pin2(Note)
RS-232 TXD
Input
Test pin3(Note)
No Connection
No Connection
Ground
Note : Please keep these pins to no connection.
10
General Specification
LCD MONITOR
VGA (D-SUB
(D SUB 15Pin)
15Pi )
Pin No.
Assignment
Pin No.
Assignment
Red
No Connection
Green
10
Ground-Sync
Bl
Blue
11
Ground
Ground
12
DDC Data
DDC 5V Standby
Cable Connection
check
13
H.Sync
Ground-Red
dR d
14
VS
V.Sync
Ground-Green
15
DDC Clock
Ground-Blur
11
General Specification
LCD MONITOR
Specification
Model
LCD PANEL
Synchronization
Power
Consumption
Power
Approval Marks
Energy
Dimension
FS-A4206F
Type
A-si TFT Active matrix
Display area
930.4(H) mm X 523.26(V) mm
Maximum Resolution
1920X1080@120Hz
Pixel pitch
0.4845(H)mm X 0.4845(V)mm
Display colors
1073.7M (RGB 10-bit data)
Contrast Ratio(Typ.)
4000:1
Viewing Angle(Typ.)
89/89/89/89
Response Time(Typ.)
5ms
Luminance(Typ.)
500cd/m2
Horizontal Frequency
135.6 KHz
Vertical Frequency
120 Hz
Maximum
120W
Standby Mode
Under 0.5W
AC 100-240V~50-60Hz
100 240V~50 60Hz 1.2A
1 2A Max
Approval Mark
UL, FCC, Mx CoC, AR-S, CE, Gost-R, SASO,
CCC,
South Africa, KC BSMI, Singapore safety, C-Tick,
CB
Efficiency
China energy label, E-Standby
Size and weight
1002.5X40X595 /17Kg(21Kg)
12
General Specification
LCD MONITOR
Model
LCD PANEL
Synchronization
Power
Consumption
Power
FS-A4206C
Type
A-si TFT Active matrix
Display area
930.4(H) mm X 523.26(V) mm
Maximum Resolution
1920X1080@120Hz
Pixel pitch
0.4845(H)mm X 0.4845(V)mm
Display colors
1073.7M (RGB 10-bit data)
Contrast Ratio(Typ.)
4000:1
Viewing Angle(Typ.)
89/89/89/89
Response Time(Typ.)
5ms
Luminance(Typ.)
500cd/m2
Horizontal Frequency
135.6 KHz
Vertical Frequency
120 Hz
Maximum
120W
Standby Mode
Under 0.5W
AC 100-240V~50-60Hz
100 240V~50 60Hz 1.2A
1 2A Max
Approval Marks
Approval Mark
UL, FCC, CB
Dimension
Size and weight
1002.5X40X595 /17Kg(21Kg)
13
General Specification
LCD MONITOR
Safety
y instructions
Operator Safety Instructions
For your safety, please read these safety instructions completely before you connect the
equipment to the power source.
The information in this summary is intended for operators.
Carefully observe all warnings, precautions and instructions both on the apparatus and in these
operating instructions.
instructions
Retain this manual for future reference.
Water and Moisture
Do not operate the apparatus under or near water - for example near a bathtub, kitchen sink, or
laundry tub, in a wet basement, near a swimming pool or in other areas with high humidity.
Never install jacks for communication cables in wet locations unless the jack is specifically
for wet locations.
designed
Do not touch the product with wet hands.
Cleaning
Unplug the apparatus from communication lines, mains power-outlet or any power source
before cleaning or polishing.
Do not use liquid cleaners or aerosol cleaners.
Use a lint-free cloth lightly moistened with water for cleaning the exterior of the apparatus.
Ventilation
Do not block any of the ventilation openings of the apparatus. Never cover the slots and
openings with a cloth or other material. Never install the apparatus near heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not place the product in direct sunlight or close to a surface directly heated by the sun.
Lightning
Never use this apparatus, or connect/disconnect communication cables or power cables during
lightning storms.
Dust
Do not operate the apparatus in areas with high concentration of dust
Vibration
Do not operate the apparatus in areas with vibration or place it on an
unstable surface.
14
General Specification
LCD MONITOR
Power Connection
ti and
d Hazardous
Voltage
V lt
The product may have hazardous voltage inside. Never attempt to open this product, or any
peripherals connected to the product, where this action requires a tool.
This product should always be powered from an earthed power outlet.
Never connect attached power supply cord to other products.
In case any parts of the product has visual damage never attempt to connect mains power, or
any other power source, before consulting service personnel
The plug connecting the power cord to the product serves as the main disconnect device for
this equipment. The power cord must always be easily accessible.
Route the power cord so as to avoid it being walked on or pinched by items placed upon or
against it. Pay particular attention to the plugs, receptacles and the point where the cord exits
from the apparatus.
Do not tug the power cord.
If the provided plug does not fit into your outlet, consult an electrician.
Never install cables, or any peripherals, without first unplugging the device from it's power
source.
Servicing
Do not attempt to service the apparatus yourself as opening or removing covers may expose
you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to
qualified service personnel.
Unplug the apparatus from its power source and refer servicing to qualified personnel under the
following conditions:
If the power cord or plug is damaged or frayed.
If liquid has been spilled into the apparatus.
If objects have fallen into the apparatus.
If the apparatus has been exposed to rain or moisture
If the apparatus has been subjected to excessive shock by being dropped.
If the cabinet has been damaged.
pp
seems to be overheated.
If the apparatus
If the apparatus emits smoke or abnormal odor.
If the apparatus fails to operate in accordance with the operating instructions
Accessories
Use only accessories specified by the manufacturer, or sold with the apparatus.
15
General Specification
LCD MONITOR
Warning
When connecting to/disconnecting from a power outlet, push/pull
on the plug itself.
Never pull the cord, in order to prevent fire caused by a short.
In order to prevent electric shock, do not connect/disconnect the
plug with wet or moist hands.
If you see smoke or smell something burning, stop using the unit,
switch off the power, pull out the plug, and then contact your local
service station.
To prevent fire, do not connect a large number of equipments
in a single line.
To prevent fire and electric shock, pull out the plug in case of thunder
and lightning.
To prevent fire and electric shock, do not try to take the monitor
apart or repair it yourself. Contact your local service station or customer
service center for inspection, modification or repair.
16
General Specification
General Specification

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2011:12:13 09:51:01+09:00
Create Date                     : 2011:12:13 09:51:01+09:00
Format                          : application/pdf
Title                           : Microsoft PowerPoint - FS-A4206F_4206C  User manual(EN) [호환 모드]
Creator                         : Sens
Document ID                     : uuid:f68e2f71-3cab-4992-a82e-42a5085e18f0
Instance ID                     : uuid:733491c4-f5e4-4a5f-9c40-d37c76c8ce34
Page Count                      : 20
Author                          : Sens

EXIF Metadata provided by EXIF.tools