DASAN ELECTRON DW-779H Wireless Headset(PP) User Manual DW 779

Download:
Mirror Download [FCC.gov]
Document ID	2679443
Application ID	WWfzBOL4LVf3W/O7KIZYpQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	31.44kB (392985 bits)
Date Submitted	2015-07-14 00:00:00
Date Available	2015-07-14 00:00:00
Creation Date	2015-07-06 09:39:23
Producing Software	Acrobat Distiller 9.5.5 (Windows)
Document Lastmod	2015-07-06 09:39:23
Document Title	Microsoft Word - DW-779_User Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	LEEMIYOUNG

1.INTRODUCTION
Package Contents
POWER ADAPTOR
User’s Manual
BASE Unit
Wireless Headset
EAR-HOOK
HEADSET & HEADBAND
TELEPHONE CONNECTION CORD
USB CABLE
(Optional)
2. Headset
Mute/ Speaker
volume
In-Use/On-Off
Indicator
Down
Up
Call Hook On/Off
Mute
Speaker Volume Up/Down
Microphone Mute (Press)
-
Fit the headband or ear-hook on the headset
Adjust the boom arm of your headset so that the microphone is positioned in
the direction of your mouth, as close as possible to your mouth.
3. Base Unit
Base Top
PC/TEL Selection
Base Bottom
Microphone Volume
Compatibility
Switch
Microphone
Mute Button
Microphone Volume Switch
When installed, adjust volume level for the best level of
Compatibility Switch
Select ‘1’ or ‘2’ until a dial tone is heard via the telephone
microphone volume.
connection.
PC/TEL
Only USB version has a this function.
AUX port
Telephone port
DC Jack
Handset port
USB port
AUX
Handset port
Telephone port
Connection for Handset LIFTER (optional extra)
Plug Handset cord from the phone to Handset port
Connect telephone cord to the headset port or handset port of a
telephone / base unit
USB Port
Connect USB cable between PC and base unit.
DC Jack
Connect Power Adapter to DC Jack
4. LED indicator
Diagram 2 ( Desk phone without HEADSET port)
Battery indicator
In-use indicator
Mute indicator
PC/TEL indicator
Charging Status
LEDs status
Charging
Battery Indicator : ‘Blinking’ 3 sec-ON, 1sec-OFF
Full Charged
Battery Indicator : ‘ON’
Low Battery
Battery Indicator : ‘Blinking’ 0.5 sec-ON, 0.5 sec-OFF
Event
LEDs status
Press Microphone mute
Mute indicator : ‘ON’
Press PC/TEL selection
PC/TEL Indicator
Hook Off
TEL : ‘OFF’
On the desk phone, unplug the handset cable from the phone
- Plug the handset cable into the HANDSET port on the BASE UNIT
- Plug the telephone cord into the TEL port on the BASE UNIT and plug the
other end of the telephone cord into the HADNSET port on the desk phone
PC : ‘ON’
In-use indicator : ‘ON’
(Desk phone with DL-570 LIFTER)
The DL-570 remote handset lifter manually lifts the desk phone handset to
make or answer a call.
5. Setting up the BASE
- Refer to the DL-570 installation guide
Diagram 1 (Desk phone with HEADSET port)
(Desk phone with EHS Adapter)
EHS Adapter enables an incoming call to be answered or ended by using the
On/Off button on the Headset..
- Refer to the EHS Adapter installation guide
- Plug the supplied telephone cord into the TEL port of the BASE UNIT
- Connect the telephone cord to the HEADSET port of the desk phone
6. Operational Instruction
8. Trouble Shooting
Plug the Power Adapter cord on the Base unit.(Note 1)
Press Hook On/Off switch to make a call
Select compatibility switch ‘1’ or ‘2’ position until you can hear the dial tone
☞
Please check the cable connection between Base unit and Phone.
Adjust speaker and microphone volume
☞
Check that the power adapter is plugged in and has power
Press Hook On/Off switch to end a call
☞
Please check the compatibility switch. Adjust compatibility switch until
1. Can not hear a dial tone.
☞
Check the TEL/PC button.
TEL Mote: PC/TEL indicator – ‘OFF’
you can hear the dial tone.
Note 1 : Factory default setup : Paired
Pairing process is automatically proceeding when plug the power adapter into the
Base Unit. (Make sure that headset is placed on the cradle and should be powered on
2. Microphone volume (TX) is low / dead.
☞ Make sure that the microphone (TX) mute function is deactivated.
☞ Check the position of the boom arm and make sure that the microphone
is placed as close as possible to your mouth (approx. 2 fingers
before power is turned on. If the headset is not placed on the cradle, pairing will be
unsuccessful.)
7. Electronic Hook Switch (optional extra)
distance).
☞
Adjust the microphone (TX) volume on the bottom of base unit.
3. Buzzing sound on the headset
☞
Telephone may not be fully immune to the radio transmission between
your headset and base. To overcome this problem, move the base unit
to at least 30 cm/12” away from the phone.
The unit enables you to answer and end calls remotely by using its built-in electronic
hook switch (EHS). EHS of this unit is only compatible with certain telephone systems
supporting EHS.
★
4. Headset echoes
☞
EHS is only compatible with certain telephone systems. In order to determine
Adjust the telephone’s volume. If necessary, adjust your microphone
volume on the headset to a lower setting.
which telephones are compatible with the EHS feature, please refer to EHS
guide or contact your local distributor. Please also refer to your telephone’s
5. EHS doesn’t work with the telephone
☞
user manual for clarification.
Make sure the telephone is compatible with the wireless headset. Refer
to the EHS guide.
6. Headset was working, but it has stopped.
☞
Headset may need pairing to the base again. Refer to the ‘Note 1’ on
‘Operational Instruction’
☞ Headset battery may be dead. Return the headset to the cradle on the
base unit for charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modiἀcations to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency
energy that can be safely absorbed by a user or bystander according to the intended usage of the
product. This product has been tested and found to comply with the FCC criteria. The handset
may be safely held against the ear of the user. The telephone base shall be installed and used
such that parts of the user’s body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : LEEMIYOUNG
Create Date                     : 2015:07:06 09:39:23+09:00
Modify Date                     : 2015:07:06 09:39:23+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - DW-779_User Manual
Creator                         : LEEMIYOUNG
Document ID                     : uuid:f8f5bc6a-b8e4-4033-974b-b26c79bec973
Instance ID                     : uuid:1d35dd24-e52f-4478-b514-6174a904ebd4
Page Count                      : 6

EXIF Metadata provided by EXIF.tools