DATECS DATECSBT301 Bluetooth Module User Manual LineaTAB4 UM

DATECS LTD. Bluetooth Module LineaTAB4 UM

User Manual-InfineaTAB4 UM

1 DATECS Linea TAB4 User Manual
Legal Notice “Made for iPod,” “Made for iPhone,” and Made for iPad” mean that an electronic accesory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible fort he operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPod, iPhone, or iPad may affect wireless performance. Compatibility Made for iPad (4th generation) iPad, iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. CAUTION: Use shielded cables to connect this device to computers. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
Overview Features: Battery: Rechargeable Li-ion Battery - 1100 mAh, Charging via USB to computer Charging via Power Station Magnetic Card Reader – 3-Track Head: Swipe Speed: Minimum of 1.97 in/sec MTBF: 1 million swipes Bidirectional reading capabilities Barcode Scanner - Class II - 1D/2D Imager: Single / Multi-scan mode 1D - MTBF: 30K hours (Laser Diode & Mirror Unit 10K hours) 2D - MTBF: 50K hours Indicators: Visual: 2 LEDs for device status I/O Connectors: 9-pin Lightning connector 10-pin female Mini-B USB connector for charging and synchronization External RS connector
Technical Data Processor 32-bit ARMTM CortexTM - M3 based Microcontroller Magnetic Card Reader (option) • 3-track bi-directional reading • ISO 7810, 7811 and 7813 Secure Magnetic Card Reader (option) • PCI PTS 3.x certified • DUKPT and Fixed Key Management • 3DES-112, AES-128, AES-256 encryption algorithms RFID Card Reader (option) • MiFARE Mini • ISO 14443 • MiFARE Classic 1K / 4K • ISO 15693 • MiFARE Ultra-Light / Ultra-Light-C • DESFire card • MiFARE Plus 2K / 4K • FeliCa Barcode Reader (option) • Opticon MDL1000* - Laser Barcode Scan Engine • Newland EM3070* - Image Sensor 752x480 CMOS, High Performance 2D Imager Scan Engine • Intermec EA-30 - Image Sensor 752x480 CMOS, High Performance 2D Imager Scan Engine • Opticon MDI3100 - Image Sensor 752x480 CMOS, High Performance 2D Imager Scan Engine Supported Barcode Types • 1D* Barcode Scanner Supported Symbologies: JAN/UPC/EAN incl. add on, Codabar/NW-7, Code 11, Code 39, Code 93, Code 128, GS1-128(EAN-128), GS1 DataBar (RSS), IATA, Industrial 2of5, Interleaved 2of5, ISBN-ISMN-ISSN, Matrix 2of5, MSI/Plessey, S-Code, Telepen, Tri-Optic, UK/Plessey Postal code: Chinese Post, Korean Postal Authority code Composite codes, MicroPDF417, PDF417 • 2D* Imager Supported Symbologies: Code 128, EAN-13, EAN-8, Code 39, UPC-A, UPC-E, Codabar, Interleaved 2 of 5, ITF-6, ITF-14, ISBN, Code 93, UCC/EAN-128, GS1 Databar, Matrix 2 of 5, Code 11, Industrial 2 of 5, Standard 2 of 5, Plessey, MSI-Plessey PDF417, Data Matrix (ECC200, ECC000, 050, 080, 100, 140), QR Code Battery Rechargeable Li-Ion Battery 3.7V / 1100 mAh Connectivity • Apple 9 pin connector • Pass-through sync through mini USB • BT 2.0 Class 2 (option) - SPP - Serial Port Profile • External serial port Device compatibility iPad 4 Buttons 2 scan buttons LED indication 2 LEDs for battery and device status Audio indication Electro - Magnetic Buzzer Weight, g 115 with battery and 2D barcode reader (without iPad) Dimensions (LxWxH), mm 128 x 51 x 45
Environmental • Operating: -10oC to +40oC / 35 to 85% RH • Storage: -20oC to +50oC / 10 to 90% RH Power Supply • 5V through mini USB • 5V through single or 5 station charger Accessories • Single station charger - SC-1 • 5 stations charger - GC-5 • Holster • Stand Table 1 * Specifications subject to change without notice.
Box Contents Your Linea Tab comes with the following items listed below: Item Part Number Descriptions Image 1 Linea Tab4 Linea Tab4 Reader / Scanner 2 USB A to mini B USB USB sync cable 3 Linea Tab User Manual User's manual Table 2 *Bulk Shipments may ship without cables and manuals in each box.
Getting Started Device overview Fig. 1 Fig. 2
The Linea Tab allows you to scan barcode and capture Magnetic Strip information onto your iPad4. Before using your Linea Tab the battery should be properly charged. The following Quick Start guide will help to get your Linea Tab ready for use. Quick Start: Step What to do Purpose Where to find more information 1 Fully charge your Linea Tab4 as recommended. The battery pack should be fully charged before use to ensure long battery life. Charging Battery, Page 9. 2 Install Software. Barcode Scanning & Card Reading requires software to be installed on to your iPad4 Please contact your distributor, Pages 11 and 12. 3 Attach device to IPad4. Connecting your Linea Tab and iPad4. Page 10. Table 3
Charging Battery Charging the Linea Tab: The Linea Tab4 uses a Lithium-Ion rechargeable battery pack. Before first use, the battery pack should be charged for at least (4) hours. To prevent electrical damage to the Linea Tab4 and/or battery pack, please use approved USB to Mini USB cables only. Fig. 3 InfineaTAB4 can be charged from USB port or Datecs power station. When the InfineaTAB4 is charging, green led is blinking (LED2). When the device is fully charged, greed led is continuously light (stop blinking). Charging via USB cable (type A to mini USB), connected to PC 5V/260mA
Attaching Device When using the Linea Tab4, care must be taken to ensure the Linea Tab4 9-pin connector and the iPad4 connector are not accidentally damaged. The figures below show how to attach your device to the Linea Tab. Blue led will blink fast, when the iPad4 is connected to Linea TAB4. (Or press scan buttons for start device) Fig. 4 Slide the device as shown on the figure above.
1D Barcode Scanning Using the 1D barcode scanner: The Linea Tab4 1D uses a scan engine that supports one-dimensional (1D) barcode symbols. The effective reading distance of the barcode reader varies depending on the barcode size. Scanning 1D Barcodes: To scan a 1D barcode fist activate the scanner. Then position the scan head as close to the barcode label as possible so that the scan line crosses both ends of the barcode as shown in the figure below. Slowly pull back the unit increasing the distance between the barcode and scan head until the barcode has been read by the scanner. Fig. 5 Scan button ~ 15-20 cm
2D Barcode Scanning Using the 2D barcode scanner: The Linea Tab4 2D uses a scan engine that supports one-dimensional (1D) and two-dimensional (2D) barcode symbols. The effective reading distance of the barcode reader varies depending on the barcode size. Scanning 2D Barcodes: To scan a 2D barcode fist activate the scanner. Then position the scan head to center the red aiming laser near the center of the barcode and the illumination box is over the outer edges of the barcode as shown in the figure below. Slowly pull back the unit increasing the distance between the barcode and scan head until the barcode has been read by the scanner. Fig. 6 Scan button ~ 15-20 cm
Card Reading Reading Magnetic Strips: The Linea Tab4 has a built-in magnetic card reader. The card reader incorporates a (3) track magnetic read head requiring a single swipe to read field data from all three tracks. The magnetic read head faces up towards the top of the cradle. When placing the card into the reader, the magnetic strip must be facing up as shown in the figure below. Keep the edge of the card flat on the inner base of the reader to ensure that the magnetic strip passes over the read head evenly. Fig. 7 User Notes: To use the magnetic card reader feature, special software must be used to read and process the card information. Swipe direction Scan direction
RFID card Reading In order to use the RFID card reading function, special software must be used. Please contact your distributor in order to get the latest demo application and SDK. Place the card on the show spot and press the read RFID card button on the application. The data will be send from the Linea Tab4 RFID reader to the iPad. Fig. 8

Navigation menu