User Manual
1 DATECS User Manual INFINEA X 1 DATECS InfineaX User manual THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. VERSION: March 2016 1 DATECS InfineaX User manual Legal Notice “Made for iPod” and “Made for iPhone” mean that an electronic accesory has been designed to connect specifically to iPod or iPhone respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible fort he operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPod, or iPhone may affect wireless performance. Compatibility Made for iPhone 5 iPhone 5S iPhone SE th iPod touch (5 generation) th iPod touch (6 generation) iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc. 1 DATECS InfineaX FCC Notice User manual FCC ID: YRWDATECSBTIX This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. No changes shall be made to the equipment without the manufacturer’s permission as this may void the user’s authority to operate the equipment. Exposure to Radio Frequency (RF) Signals The Infinea X, incorporating the iPhone 5/iPod Touch, has been tested and meets applicable limits for radio frequency (RF) exposure. Specific Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. The SAR limit is 1.6 watts per kilogram averaged over 1 gram of tissue. During testing, the iPhone 5/iPod Touch devices, incorporated within the Infinea X, are set to their highest transmission levels and placed in positions that simulate use against the head, with no separation, and near the body, with 5mm separation. When using the incorporated iPhone 5/iPod Touch functionality, to reduce exposure to RF energy, use a hands-free option, such as the built-in speakerphone, the supplied headphones or other similar accessories. Carry the Infinea X at least 5mm away from your body to ensure exposure levels remain at or below the as-tested levels. Cases with metal parts may change the RF performance of the device, including its compliance with RF exposure guidelines, in a manner that has not been tested or certified. The Infinea X complies with the FCC safety requirements for RF exposure in accordance with FCC rule part §2.1093 and KDB447498 D01 for portable use conditions. The Infinea X, incorporating the iPhone 5/iPod Touch, must not be co-located or operated in conjunction with any other antenna nor transmitter. 1 DATECS InfineaX User manual CONTENTS Legal Notice............................................................................................................................................. 3 Compatibility ............................................................................................................................................ 3 1. Technical specification ........................................................................................................................ 6 2. Box Contents ....................................................................................................................................... 7 3. General View ....................................................................................................................................... 8 4. Operation Modes ............................................................................................................................... 11 4.1 Attaching device ......................................................................................................................... 11 4.2 Running device........................................................................................................................... 11 4.3 Battery charging and status level ............................................................................................... 11 4.4 Scanning barcodes..................................................................................................................... 12 4.5 Bluetooth connecting to iOS device for transferring audio......................................................... 12 4.6 Clearing Bluetooth pairing info ................................................................................................... 13 4.7 Switching between Rear and Front Speakers............................................................................ 13 4.8 Automatic charge ....................................................................................................................... 13 4.9 Vibration on scan........................................................................................................................ 13 4.10 Pass-through sync through mini USB ...................................................................................... 13 4.11 Reset the InfineaX .................................................................................................................... 13 4.12 Scanning barcodes................................................................................................................... 13 4.13 RF card reading........................................................................................................................ 14 1 DATECS InfineaX User manual 1. Technical specification Processor Contactless Card Reader (option) 32-bit ARMTM CortexTM - M3 based Microcontroller ISO/IEC 14443 Type-A/MIFARE: - MIFARE MINI - MIFARE CLASSIC-1K, MIFARE CLASSIC-4K - MIFARE ULTRALIGHT, ULTRALIGHT-C - MIFARE PLUS 2K/4K - MIFARE DESFire - and others ISO/IEC 14443 Type-B: - supports most of the cards ISO/IEC 15693: - supports most of the cards Barcode Reader (option) • Intermec EA-30* - Image Sensor 752 x 480 CMOS, High Performance 2D Imager Scan Engine • Intermec EA-31 - Image Sensor 752 x 480 CMOS, High Performance 2D Imager Scan Engine • 2D* Imager Supported Symbologies: EAN/UPC, GS1 Databar (limited expanded & omni-directional), RSS, Code 39, Code 128, UCC/EAN 128, ISBN, ISBT, Interleaved/Matrix/Industrial and Supported Barcode Standard 2 of 5, Codabar, Code 93/93i,Code 11, MSI, Plessey, Telepen, Types Postal codes: Australian Post, BPO, Canada Post, Dutch Post, Japan Post, PostNet, Sweden Post Data Matrix, PDF417, Micro PDF 417, Codablock, Maxicode, QR, Aztec, GS1 composite codes, Direct Part Marking Reading multicodes Battery Connectivity Device compatibility Buttons LED indication Audio indication Vibration capabilities Sound capabilities Certifications Rechargeable hard pack Li-Ion Battery 3.7V / 1900 mAh Rechargeable hard pack Li-Ion Battery 3.7V / 3800 mAh (option) • Apple 9 pin connector • Pass-through sync through special 4 pin waterproof connector • Pass-through sync through mini USB • Bluetooth for audio signals transfer between InfineaX and iOS device Apple iPod 5 / iPod 6 / iPhone 5 / iPhone 5S / iPhone SE • Scan button • Battery status button 18 LEDs for battery and emergency status Electro-Magnetic Buzzer Micro Vibration Motor - Rated speed: 14,000 ± 2,000rpm • 1.7-W mono fully differential audio power amplifier • Front Speaker – 150mW • Rear Speaker – 750mW • Electret Condenser Microphone CE, Apple® MFi 1 DATECS InfineaX Weight, g Dimensions (LxWxH), mm Environmental Drop Test Power Supply Accessories User manual 200 with battery and 2D barcode reader (without iPod/iPhone) 148 x 72 x 31 • Operating: -10oC to +40oC / 5% to 90% RH • Storage: -20oC to +50oC / 5% to 90% RH 1.5 m, 6 faces + 4 edges on concrete • 5V through special 4 pin waterproof connector • 5V through single or 5 station charger • Single station charger - SC-1 • 5 stations charger - GC-5 * Specifications subject to change without notice. 2. Box Contents Item Part Number InfineaX USB A to mini B(0.9m) InfineaX User Manual IX-BP Descriptions InfineaX Scanner USB sync cable User's manual Li-Polymer Battery 3,7V Image 1 DATECS InfineaX User manual 3. General View Front Speaker Mounting torx screws (1) (4) (2) (5) Home button (3) (6) Microphone 1 DATECS InfineaX User manual Rear Speaker RF reader Battery Pads for charging station and sync Scan engine On/Off button 1 DATECS InfineaX User manual Volume buttons LEDs indications Battery status button LEDs indications mini USB connector Scan button Button for switching between Rear/Front speakers 10 1 DATECS InfineaX User manual 4. Operation Modes 4.1 Attaching device Remove all 6 mounting screws, slide device to 9-pin lightning connector. After that all 6 screws must be mounting again. 4.2 Running device Important - Before first use, battery must be connect to the device. Press one of these buttons; Scan, Status or Speaker Switch. Run app “LibraryDemo”, and device is ready for using (Pic.7). Pic. 7 4.3 Battery charging and status level This device can be charge from USB port or Datecs charging station. Connect mini USB cable to USB port and charge will start. When the device is charging one green LED is light (Pic.8). Pic. 8 11 1 DATECS InfineaX Battery level status can be check, when is press battery status button: - Battery percentage above 75% – LEDs flash on green - Battery percentage between 50-75% – LEDs blinks on green - Battery percentage between 25-50% – LEDs blinks on orange - Battery percentage between 10-25% – LEDs blinks on red - Battery percentage under 10% – One red LED is blinks User manual On the “LibraryDemo”, press battery indicator or battery level button (Pic.9): Pic. 9 4.4 Scanning barcodes Turn scan engine to barcode and press “Scan barcode” or scan button. 4.5 Bluetooth connecting to iOS device for transferring audio - For connecting InfineaX Bluetooth to iOS device, open setting and select Bluetooth, then on available Bluetooth device will shown “InfineaX”. Select that Bluetooth device. Pic. 10 and 11 12 1 DATECS InfineaX User manual 4.6 Clearing Bluetooth pairing info - Hold on same time status and rear speaker button until the device is beep twice, if after that the devices is still not showing on iOS device available for connecting press on same “battery status” and “scan” button for ~5sec. *Note: If after Bluetooth paring info clearing, InfineaX is not visible, perform with “Reset InfineaX” (4.11) 4.7 Switching between Rear and Front Speakers. - For changing active speaker, press speaker switching button. When the rear speaker is active, blue led is light. 4.8 Automatic charge - When the battery level is above 3,9V – InfineaX is automatically start to charge iPhone5 or iPod5. (If the option is enabled in settings) 4.9 Vibration on scan - This function can be enabled or disabled 4.10 Pass-through sync through mini USB - This function can be enabled or disabled 4.11 Reset the InfineaX - Holding on same time status and scan button for ~5sec 4.12 Scanning barcodes The InfineaX uses a scan engine that supports one-dimensional (1D) and two-dimensional (2D) barcode symbols. The effective reading distance of the barcode reader varies depending on the barcode size. Scanning Barcodes: To scan a barcode fist activate the scanner. Then position the scan head to center the red aiming laser near the center of the barcode and the illumination box is over the outer edges of the barcode. Slowly pull back the unit increasing the distance between the barcode and scan head until the barcode has been read by the scanner. 13 1 DATECS InfineaX User manual 4.13 RF card reading Start the app and select tab “RF”. Place the card on the spot with RF symbol (back side on barcode cover). 14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Page Count : 14 Has XFA : No Title : Description : Subject : Creator Tool : Producer : Foxit PhantomPDF Printer Version 7.1.0.112 Keywords : Create Date : 2016:05:26 09:33:30+03:00 Modify Date : 2016:05:26 09:33:35+03:00 Author : Creator :EXIF Metadata provided by EXIF.tools