DEVELOPMENT ST-ILDIM Dimming switch User Manual ST ILDIM 1 IM E 2019 3 11

INTERNATIONAL DEVELOPMENT COMPANY Dimming switch ST ILDIM 1 IM E 2019 3 11

Users Manual

8.5"11"Model: ST-ILDIM-1LED String Light Dimming Kitwith Remote ControlUse and Care GuideRead and Save this Instructions Before UseENInternational Development Company899 Henrietta Creek Rd. Roanoke, TX 76262 USAToll-free: 1-877-723-0723Made in China© 2019 IDC, all rights reserved. The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. This product is manufactured forInternational Development Company.INSTALLATIONA- End Plug ConnectorB- AdapterC- Prong Plug AC Outlet1. Connect 1st String Light set to be controlled by dimmer to End Plug (A)2. Connect additional string lights to 1st string light.3. Plug in Prong Plug – C to power outlet.4. Turn on or Dim Lights accordingly.A B C
SAFETY INFORMATION 8.5"11"WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way.WARNINGS: READ ALL INSTRUCTIONS BEFORE YOU START:CAUTION-To reduce risk of fire, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this product.WARNING-RISK OF ELECTRIC SHOCK! Disconnect power at source prior to connecting cord set, lamping (installing light bulbs into sockets), re-lamping or servicing in any way.ABOUT THE CORD SETThis dimming kit is an accessory to Honeywell filament string light and does not function unless used in conjunction with ST1XXA2X4XXX filament string light products.When using the dimming kit, be sure to follow the maximum run lengths as follows:ST124A2X4XXX 22 string lights 200WST112A2X4XXX 44 string lights 200WST136A2X4XXX 22 string lights 200WST124A2X4X85 50 string lights 200WST148A2X4X85 26 string lights 200WWARNING-RISK OF ELECTRIC SHOCK!! For outdoor string lights, do NOT connect cord set to light strings during rain or other inclement weather conditions. Connect Dimming Kit to string lights only during dry and calm weather conditions.WARNING-RISK OF FIRE!! DO NOT OVERLOAD SOCKETS OR LIGHT STRING!! DO NOT exceed the maximum. number of connected strings or total feet(and sockets) listed in the table below.WARNING-RISK OF ELECTRIC SHOCK!! Do not operate light string with any open sockets. Make sure each socket has a bulb securely fastened before connecting to a power source.Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC). Use this product only with its attached plug-in power cord. Any other power cord or feed may damage the fixture.EN | 1 EN | 2WARNING: The dimming kit operates with 120V AC power only. Do not use with any other power supply type. Use only with Honeywell filament string lights ST1XXA2X4XXX to retain product warranty.FCC: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. **********************************************************************************************NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.USING THE REMOTE CONTROL:The radio frequency handheld remote is battery operated (one A23 battery, included). This remote operates within 88.5ft (27m) of the dimming kit. Do not install dimming kit with string light more than 88.5ft (27m) away from the intended location of remote control use.INSTALL BATTERYREMOTE CONTROL OPERATINGWARNING: Do not dispose batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or mutilate batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium or nickel hydride) batteries with lithium batteries. !- Remove the battery cover.- Place a A23 battery into the battery compartment aligning polarity (+)(-) as indicated- Return battery cover.Note: When using the remote control for the first time, check that the battery is in place.Battery CoverPARTS AND SPECIFICATIONSBB: Wall Anchors (2) CC: Bracket (1) DD: Remote Control (1)EE: Dimmer Kit (1)AA: Screw (2)FF: A23 Battery (1)Power On/Power OffIncrease BrightnessDecrease BrightnessCandle SceneNote: The working temperature for the remote control is-20℃-40℃(-4F-104F).

Navigation menu