DIEWU Technology DW-PSW04 Wireless computer switch User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2641163
Application ID	ovQZbj9kUtgequ9yrxFfAw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	69.93kB (874144 bits)
Date Submitted	2015-06-09 00:00:00
Date Available	2015-06-09 00:00:00
Creation Date	2015-05-29 13:59:36
Producing Software	Acrobat Elements 7.0.5 (Windows)
Document Lastmod	2015-06-05 14:43:51
Document Title	Microsoft Word - User Maual for wireless remote computer switch.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

User Manual
Wireless computer switch
Chapter 1 Introduction
1.1 Overview of the products
Congratulations on your purchase of this computer switch. The switch can control
computer’s power ON/OFF within 20 meters.
The switch include two parts:
Internal connection part ‐ connection card
External control part ‐ mini remote control switch
Before purchasing, please kindly check your slot, then decide to choose PCI interface version
or PCIe interface version.
1.2 Features
※ Miniature design, easy to carry
※ Support the computers which have available PCI / PCIe slot
※ Plug‐and ‐Play installation
※ Induction distance: 20 meters
※ Two kinds of interface: PCI and PCIe
※ Two buttons: Reset and Power
※ Red LED indicator
※ Powered by one button battery
※ The internal connection card and external remote control switch are paired, please do
not mix those two parts with other sets
Chaper 2 Installation Guide
2.1 Installation
To install the switch, please follow these steps listed below:
1. Turn off your computer and unplug the power cord and all cables.
2. Remove your computer’s case cover
3. Unplug the the power cable and reset cable from motherboard
4. Locate an available PCI or PCIe slot
5. Remove the screw that secures the black plate (the small piece of metal that covers the
opening for PCIe card on the back panel of your computer), then remove the back plate.
6. Carefully insert the switch (internal connection part) into the PCI / PCIe slot, then connect
the “POWER SW” and “RESET SW” to the right position in the motherboard. Do not touch
the metal connector on the internal part (Refer to the Figure 1.1)
7. Secure the switch (internal connection part) to the case using the screw you removed
from the back plate
8. Reinstall your computer’s case cover
9. Plug in the power cord and other cables, and then press the power button of switch to
turn on the computer
Chapter 3 Common problems
1. Can’t turn on the computer by pressing the power button
Please check if the LED indicator will blink when pressing Power button or Reset button,
If doesn’t blink,it shows you should change the battery.
If blink, but still can’t turn on the computer, please try do as the following steps:
(1) Unplug the computer’s power cord, pull and plug the connection card for several times,
use the eraser wipe the goldfinger, re‐plug the card
(2) Check if the POWER SW and RESET SW put in the correct position, be sure they are not
loose
2. Pressing the button, the LED indicator of switch and card both light, but still can’t turn on
the computer
Solution: need to re‐match
Matching method: long press the Power button and Reset button at the same time, until the
indicator light continuous flash for five times (Don’t use this method if not necessary)
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Elements 7.0.5 (Windows)
Create Date                     : 2015:05:29 13:59:36+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2015:06:05 14:43:51+08:00
Metadata Date                   : 2015:06:05 14:43:51+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : Microsoft Word - User Maual for wireless remote computer switch.docx
Document ID                     : uuid:aed90de7-b30b-480c-a725-c47d6e0c8174
Instance ID                     : uuid:fc26a807-4787-4d94-a0b9-5e257d65fb30
Page Count                      : 3
Author                          : Administrator

EXIF Metadata provided by EXIF.tools