User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1288486 |
| Application ID | TjkCOXORWiczHOqr0lRfqA== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 55.43kB (692869 bits) |
| Date Submitted | 2010-05-31 00:00:00 |
| Date Available | 2010-06-01 00:00:00 |
| Creation Date | 2010-05-28 16:52:52 |
| Producing Software | Adobe PDF library 8.00 |
| Document Lastmod | 2010-05-28 16:52:52 |
| Document Title | 說明書æ£é¢_英文_æ–°é›»æ± è“‹_20100419 |
| Document Creator | Adobe Illustrator CS3 |
B. Install and Change Battery 1. Install the Battery A. Overview： 1. Button: Power On(Off), Pairing, Change mode Light Indicator 2. 2.5mm Phone Jack Left 3. Battery Cover Put the battery into the unit and close the battery cover (Pic. 1) Check the cover indication “ ” is aimed at “ ”as show on Pic. 1. Close the cap by rotating the battery cover clockwise about 45 degrees. C. Pairing mode : Object : BSH-02 a. Turn on the BSH-02 device and go to pairing mode ( press the button A about 8 sec.)。 Clockwise 45 2. Change Battery When you want change the battery. Rotate counterclockwise 45 degrees, as show on Pic. 2. Pull the battery cover and change the battery. 3. Power On 3sec. 5sec. Pic. 1 b.Confirm the BMD-01 is power Off. Press the BMD-01 button about 6 sec. till the indicator light flashes green and red. 3 sec. Counterclockwise 45 Pic. 2 When the unit is power off, please press the button about 3 sec. till the indicator light flashes green. 3 sec. 3 sec. c. When those units have been successfully paired, their indicator lights flash green. 4. Power Off Press the button about 3 sec. till the indicator green light flashes 3 times. D. Change mode 3 sec. 2. HSP Standby mode： E、Light indicator table BMD-01 function BMD-01 have 3 modes can be selected, A2DP, When BMD-01 setting on HSP Standby mode (HSPS) HSP standby and HSP always On. Different modes will ; When you have a signal income or push the PTT (Push to Talk) Turn On Green light 1 time connect different channeal. , it will auto connect with BSH-02. Searching Green light flash quickly.(15 sec.) Press the button to change mode. This mode is suitable for you want listen music from BHS-02 Turn Off Green light flash 5 times. For Example： by A2DP profile and use Radio from BMD-01. Paining mode Green and red lights flash (60 sec.) a. If you want to use Radio, and need play music from mobile phone. You need set the BMD-01 to HSP standby mode. The light will continue flash green light 2 times every 2 sec. 3. HSP Always On mode： Light inducator A2DP Mode Green light flash 1 time every 2 Sec. HSPS Mode Green light flash 2 times every 2 Sec. HSPAO Mode Green light flash 3 times every 2 Sec. If your Radio communication is the most important, you need set When BMD-01 setting on HSP Always On mode (HSPAO) Standby Green light flash 1 time every 6 Sec. the BMD-01 to HSP always On mode. ; This mode will continue connect with BSH-02, no matter the Low Power Red light flash every 6 Sec. b. If you want to use audio player (ex. Navigation device or ipod), you need set the BMD-01 to A2DP mode. 1. A2DP mode：(Default setting) The BMD-01 will set at A2DP Profile, this mode is useful by connect with music audio devices. (ex. Audio player, GPS, Radar detector). The light will continues flash green light 1 time every 2 sec. signal is incoming or no signal. This mode is suitable for highly use Radio, and hope no lose F.Specifion Chipset CSR BC05 V2.1+EDR timing by communication from Radio. Profile HSP, A2DP The light will continue flash green light 3 times evey 2 sec. Frequency 2402~2480 MHz Range 10 meters (Open area) Power Supply 1 x AAA battery Standby time Use time Music 17 hrs / Talking 19 hrs Dimensions 60(L)x 36(W)x 16(H)mm Weight 18g (Without battery weight) E. Wack Up Function If the range between BMD-01 and BSH-02 over 10 meters, they will be disconnected. Press BMD-01 button, it will be auto searching and connect to BSH-02. 120hrs Federal Communication Commission Interference Statement You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. FCC Radiation Exposure Statement 1. This Transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2010:05:28 16:52:52+08:00 Create Date : 2010:05:28 16:52:52+08:00 Metadata Date : 2010:05:28 16:52:52+08:00 Creator Tool : Adobe Illustrator CS3 Format : application/pdf Title : 說明書正面_英文_新電池蓋_20100419 Document ID : uuid:4af8f293-3749-495f-9088-9a1a44011170 Instance ID : uuid:2f43d549-bf6a-433f-9e49-5ef374542bdd Producer : Adobe PDF library 8.00 Page Count : 2 Container Version : 11 Creator Version : 13 Creator : Adobe Illustrator(R) 13.0 For : kong.shao, Bounding Box : -282 -143 560 438EXIF Metadata provided by EXIF.tools