DORAN BOOSTER Tyre Pressure Monitoring System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2275843
Application ID	sh6cFjBFsDsUfKZG/zYKgw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.39kB (304901 bits)
Date Submitted	2014-05-23 00:00:00
Date Available	2014-05-23 00:00:00
Creation Date	2014-05-06 18:23:25
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2014-05-06 18:23:25
Document Title	Users Manual
Document Creator	Microsoft® Office Word 2007
Document Author:	User

SMART BOOSTER User Manual
The smart booster is used to transmit the signal of transmitter and
magnified it. Then transmit it to the monitor. The smart booster can
match the different monitors automatically. In order to ensure good
communication, please choose a suitable location for it on the beam of
the vehicle bottom. The location should be near the middle of the vehicle
bottom.
Smart Booster
1. Fix the booster onto rubber plate with 4 screws with diameter of 6mm.
2. Fix rubber plate and triangle together with 2 screws with diameter of
6mm.
3. Drain 2 holes with diameter of 6mm on the beam of the vehicle bottom
according to the installation holes in triangle and then fix the booster
with the screws. As shown below:
Method1. Perpendicular to the beam of the vehicle bottom
beam
triangle
Power wire of smart booster
Mothod2. Parallel to the beam of the vehicle bottom
Note: The side with power wire face up.
4. The smart booster with 3 power wires. Connect brown power wire with
positive of vehicle’s continuous power supply, blue wire with the
positive of ignition switch, the bule wire have 12V power supply only
when the ignition switch is powered. Connect the yellow and green
wire to ground. Then fix the power wires with nylon strips.
Connect positive of 12V/24V
contiuous power supply
Connect ground
Connect positive of ignition switch
5. Indicator light explanation
Three red LED lights in the transparent window of smart booster, from
left to right: power indicator, transmitting indicator and receiving
indicator light. As shown below:
power indicator
IMPORTANT NOTES:
1. Smart booster should be installed in the free space properly.
2. If there isn’t a proper position in the middle bottom of vehicle, user
can install it in the side of vehicle.
3. In order to ensure good communication of smart booster, please don't
conjoint the smart booster to the metal directly.
4. The power wires should be fixed with nylon strips to prevent them
being frazzling and short circuit.
5. Ensure the input voltage is accordant with smart booster voltage.
Connect the power wires according to marked positive and negative
wire.
6. Please connect a 2A waterproof fuse at the position of smart booster
connect the continuous power supply of vehicle to ensure the safety of
circuitry.
Specifications:
Modulation Type: FSK
Mid-frequency: 434.1 MHz
Receiving Sensitivity: -105 dBm
Input Voltage: 12V / 24V
Operating Temperature: -40℃～+85℃
Storage Temperature: -30℃~75℃
Federal Communications Commission (FCC) Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
Language                        : zh-CN
Tagged PDF                      : Yes
Title                           : 中继器的安装注意事项
Author                          : User
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2014:05:06 18:23:25+08:00
Modify Date                     : 2014:05:06 18:23:25+08:00
Producer                        : Microsoft® Office Word 2007

EXIF Metadata provided by EXIF.tools