DYNACO USA 6803 Wireless Sensing Edge System User Manual Visio WDD vsd

DYNACO USA, Inc. Wireless Sensing Edge System Visio WDD vsd

Users Manual

WDD - Wireless DYNACO Dectector USER GUIDEOperating descriptionThe WDD is a wireless sensing edge system. The sensing edge is conformed of, a conductive rubber section, sealed wireless transmitter, and end cap. The sensing edge is installed the full width of the door in the doors soft bottom bag. Obstacles/obstructions in the door opening will be sensed by the edge when the door comes down and makes contact with it. The conductive rubber triggers the transmitter to send a signal to the controller to reopen the door. A very short and rapid transmission happens only when the sensing edge makes contact with an obstacle/obstruction and will not trigger again until that sensing edge returns back to the open state.The system operates according to the open loop principle. The open loop operation offers a longer life for the transmitters lithium battery, because energy is consumed only when the sensing edge makes contact with a obstacle/obstruction, otherwise it is inactive.Reference Number: WDD-US0326-12Technical description for ARF6803 TransmitterPower supply: Lithium Battery 3.6V 1.2AhFrequency: 868.3 MHzEffective radiated power: -20dBm or 10µWTransmission Mode: Amplitude modulation 100% or ASKBattery Life: 10 years no transmissions or100,000 detections minimumSeal coating: UV-cured resinPerformance: Transmission speed 2400bps NRZ100m operating radius in open spaceTechnical description for ARF6838 ReceiverPower supply: 24vac or vdcFrequency: 868.3 MHz sensitivity 0.7µV for 12dB S/N (BER0.1)Bandwidth: < 400kHzReception Mode: Amplitude demodulation. Super heterodyne with simple frequency changeRelay out:: NO - NCResponse time of the complete system: < 500msOperating temperature: -20°C to + 70°C* DYNACO reserves the right to modify the characteristics of its products and parts without preceding notice.DYNACO THE SAFEST CHOICEPage 1 of 2Technical description of the Sensing egdeMaterial: EPDM 65 degrees shore AOperating temperature: -20°C to + 80°CProtection index: IP 67 with two sealed endsOperating Mode: The rubber section consists of two conductive rubber sections that each envelop a copper wire, and an outer insulating section of non conductive rubber. Pressure lower than 10N on the bottom of the section creates a short-circuit between the internal conductive parts and transmits a closed contact to the extremities through the copper wires.
WDD - Wireless DYNACO Dectector USER GUIDEWDD Sensing edgeThe WDD transmitter wires are soldered to the sensing edge leads and fully encapsulated in a rubber housing. The transmitter housing is adhesively sealed to prevent water and contaminants from effecting operation of the system. The WDD sensing edge assembly is then adhered in the doors soft bottom edge.Replacement of the sensing edge should be preformed by a certified DYNACO dealer/technician or by DYANCO USA, Inc.Reference Number: WDD-US0326-12* DYNACO reserves the right to modify the characteristics of its products and parts without preceding notice.DYNACO THE SAFEST CHOICEPage 2 of 2Synchronizing the systemFollow the instructions below to synchronize the transmitter to receiver.A red LED illuminates across from connector 9 indicating that the WDD receiver is operational and at a ready state.1. Lower door so that the sensing edge can be triggered easily from the control box height. Push in the E-stop to hold the position of door.Note: If control box mounted away from door, an assistant may be need for synchronizing the system.2. Push and hold sync button using small screw driver. 3. The green LED will illuminate next to the red LED.4. Trigger the sensing edge on door by pushing up on the soft bottom bag. The green LED will blink.5. Release the sync button.6. Test the synchronization: Trigger the edge and a audible click will be heard, also the LED on the DYNALOGIX (DY4100) control board will illuminate.FCC & IC RegulationModel: ARF-6803-EFCC ID A5Y6803IC: 10163A-ARF6803EPursuant to FCC 15.21 of the FCC Rules, changes not expressly approved by DYNACO USA, Inc. might cause harmful interference and void the FCC authorization to operate this product.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.This product complies with FCC OET Bulletin 65 radiation exposure limits set forth for an uncontrolled environment.This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:1. This device may not cause interference, and2. This device must accept any interference, including interference that may cause undesired operation of the device.

Navigation menu