Dacor EWD24SCH User Manual WARMING DRAWER Manuals And Guides L1002500
DACOR Warming Drawer Manual L1002500 DACOR Warming Drawer Owner's Manual, DACOR Warming Drawer installation guides
User Manual: Dacor EWD24SCH EWD24SCH DACOR WARMING DRAWER - Manuals and Guides View the owners manual for your DACOR WARMING DRAWER #EWD24SCH. Home:Kitchen Appliance Parts:Dacor Parts:Dacor WARMING DRAWER Manual
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
Installation Warming Models: Pa_ No. 102345 Rev. Q Instructions Drawer ERWD27, ERWD30, EWD24, EWD27, EWD30, EWD36, IWD24, IWD27, IWD30, MRWD27, MRWD30, MWDH27, MWDH30, MWDV27, MWDV30, OWD24 All specifications are subject to change without notice. Dacor ®assumes no liability for changes © 2007 Dacor, all rights reserved. to specifications. Before You Begin .............................................................. Important Safety Instructions .......................................... General Safety Precautions ............................................. Installation Specifications ................................................ Verifying the Package Contents ....................................... Installation Planning ......................................................... Install Support Platform in Cabinet .................................. Electrical and Environmental Specifications .................... 1 1 2 3 3 3 6 6 Installation instructions .................................................... Remove the Drawer ........................................................ Installing the Chassis ....................................................... Re-installing the Drawer ................................................... Towel Rack Installation ................................................... Verify Warming Drawer Operation ................................... Installation Checklist ........................................................ 7 7 7 8 8 9 9 Important: InstalJer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you begin the installation process. Leave these installation instructions with the customer. Customer: Keep these installation instructions for future reference and the local electrical inspector's use. If you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team, For repairs to Dacor appliances under warranty call the Dacor Distinctive Service line, Whenever you call, have the complete model and serial number for your appliance available, The numbers are found on the product data label located on back of the drawer front, The data label also contains the product electrical requirements Dacor Customer Service Phone: (800) 793-0093 (U.S.A. and Canada) Monday -- Friday 6:00 A.H. to 5:00 P.M.Pacific Time Web site: www.Dacor.com Dacor Distinctive Service (repairs under warranty only) Phone: (877) 337-3226 (U.S.A. and Canada) Monday -- Friday 6:00 A.H. to 4:00 p.m. Pacific Time Important Information About Safety Instructions The important Safety instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. • Always contact the Dacor Customer Service Team about problems and conditions that you don't understand, Product data label on back for drawer front Safety Symbols and Labels DANGER Immediate hazards that WILL result in severe PerSonal njury 0r death: WARNING HaZards 0i unsafe practices that COULD result in Severe personal injury or death. CAUTION j HaZards 0i uasafe practices that COULD res u t personal injury or property damage_ nor J _a_D_ f General Safety Precautions To reduce rJsk of fire, electrJc shock, serJous Jnjury or death when usJng your applJance, follow basJc precautions, JncludJng the followJng: _] WARNING 2 _SCD_ WARNING Verifying the Package Contents c B • (3) mounting screws - PN 83569 • Wire rack with mounting hardware (OWD24 only) (1) PN 83619 (screw), (1) PN 83267 (clamp) \ Installation Planning • Chassis A qualified technician must complete the installation of this builtin appliance. Proper installation is the customer's responsibility. 5/16" (8 ram) Carefully check the location where the drawer is to be installed. The drawer should be placed for convenient access. Make certain that electrical power can be provided in the selected location. Install the warming drawer in wood cabinets only. • Plan the installation so that all minimum clearances are met or exceeded. Dimensions shown provide minimum clearances, unless otherwise noted. Be certain that proper clearance is provided for the drawer door when it is in the open position. • The specified minimum cabinet depth and width must be provided. The cabinet depth and width must completely enclose the recessed portion of the drawer. f Drawer Cabinet cutout dimensions must be used as indicated. All contact surfaces between the appliance and the cabinet must be solid and level. The drawer support platform must be flush with the bottom edge of the cabinet cutout. • Make certain that you have everything necessary to ensure a proper installation before proceeding. • A custom front panel is required for IWD series models and optional for OWD24. • An optional Epicure ® style front panel kit is available for model OWD24. open Overall Dimensions - IWD/OWD Series Top View 40" (101.6 cm) Mounting hole, 9 places 3 prong 120 Vac power cord I I I ol o Chassis without drawer installed ** = OWD24 Drawer Face Dimensions (IWD/OWD Series) Model (A) Dimension Drawer Face Width (B) Dimension Chassis Width Chassis mounting holes Dimensions (IWD/OWD Series) (C) Dimension Chassis Face Width IWD24 22 5/16" (56.7 cm) 22 1/4" (56.5 cm) 22 3/8" (56.8 cm) IWD27 25 5/16" (64.3 cm) 25 1/4" (64.1 cm) 25 3/8" (64.5 cm) IWD30 28 5/16" (71.9 cm) 28 1/4" (71.8 cm) 28 3/8" (72.1 cm) OWD24 22 1/2" (57.1 cm) 22 1/2" (57.1 cm) 22 1/2" (57.1 cm) (D) (E) (F) (G) Dimension Drawer Dimension Chassis Face Height Depth Depth Height 8 15/16" (22.7 cm) 23 3/8" (59.4 cm) 23 13/16" (60.5 cm) 9 1/16" (23.0 cm) 11 7/8" (30.2 cm) 20" (50.8 cm) 18" (45.7 cm) 11 7/8" (30.2 cm) See following page for chassis Dimension Drawer dimensions Dimension Chassis for other models da=Dr, 3 (A) Drawer Face Width (B) Chassis Face Width (C) Chassis Width ERWD27 27" (68.6 cm) 26 5/8" (67.6 cm) 25 1/4" (64.1 cm) ERWD30 30" (76.2 cm) 29 5/8" (75.2 cm) 28 1/4" (71.8 cm) EWD24 24" (61.0 cm) 23 5/8" (60.0 cm) 22 1/4" (56.5 cm) EWD27 27" (68,6 cm) 26 5/8" (67.6 cm) 25 1/4" (64.1 cm) EWD30 30" (76,2 cm) 29 5/8" (75.2 cm) 28 1/4" (71.8 cm) EWD36 36" (91.4 cm) 35 5/8" (90.5 cm) 34 1/4" (87.0 cm) MRWD27 26 3/4" (67,9 cm) 26 5/8" (67.6 cm) 25 1/4" (64.1 cm) MRWD30 29 3/4" (75,6 cm) 29 5/8" (75.2 cm) 28 1/4" (71.8 cm) MWDH27 27" (68,6 cm) 26 5/8" (67.6 cm) 25 1/4" (64.1 cm) MWDH30 30" (76,2 cm) 29 5/8" (75.2 cm) 28 1/4" (71.8 cm) Drawer Face Dimensions MWDV27 27" (68,6 cm) 26 5/8" (67.6 cm) 25 1/4" (64.1 cm) (MWD series shown) MWDV30 30" (76.2 cm) 29 5/8" (75.2 cm) 28 1/4" (71.8 cm) Model Warming Drawer Overall Dimensions See page 3 for IWD and OWD series chassis dimensions B "q =,- C =_ ERWD \ 3 1/2" 1 EWD I-- 3 7/16' 1 (,9 cm) Chassis 23 3/8" (59.4 cm) (87cm),, 1 1/8'_D_ 1 _10 _" (2.9 cm) //I...... MRWD30B (only) (2.5 cm) l I All other MRWD series A MWDH/V (31/4"m_ I ' 5/64" _)mm) Drawer open cm) i (60.5 cm) 10" (25.4 cm) 1/2" (1.3 cm) Chassis 4 _SCD_ -_, Handle Dimensions 23 13/16" Mounting hole 9 places Overall Dimensions Top View (EWD series shown) iv Dimensions 40" (101.6 cm) 3-prong 120 Vac power cord \ ® ® ®® • Warming drawer I 36" typ. (91.4 cm) _C o® 120 Vac electrical outlet Warming drawer 3/4" min.* (1.9 cm) 1 D i c Warming drawer C 120 Vac_ !1_ elect. D ! 9 single wall oven 27"/30"/36" Dacor l . cm) i Warming drawer C 120 Vac_ I_ j elect. B Toe kick 1 1/2" (3.8 cm) Cooktop..._ ® f O Typical countertop Warming drawer ! ® O 120 Vac electrical outlet 36" typ. O (91 "l cm) A Cutouts _1 3/4" min.* (1.9 cm) Dimensions NOTES: Models EWD36 and OWD24 cannot be installed above or below another warming drawer (any type). Model OWD24 is not approved for installation above, below or adjacent to a wall oven or a warming drawer, including the same model. Model (A) Cutout Width (B) Min. Width to Adjacent Doors/ Drawers (C) Cutout Height (D) Min. Vertical Gap Between Cutouts ERWD27 25 1/2" (64.8 cm) 27 1/4" (69.2 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* ERWD30 28 1/2" (72.4 cm) 30 1/4" (76.8 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* EWD24 22 1/2" (57.2 cm) 24 1/4" (61.6 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* EWD27 25 1/2" (64.8 cm) 27 1/4" (69.2 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* EWD30 28 1/2" (72.4 cm) 30 1/4" (76.8 cm)* 9 1/8" (23.2 cm) EWD36 34 1/2" (87.6 cm) 36 1/4" (92.1 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* NA IWD24 22 1/2" (57.2 cm) 9 1/8" (23.2 cm) 1 1/16" (2.7 cm) IWD27 25 1/2" (64.8 cm) 9 1/8" (23.2 cm) 1 1/16" (2.7 cm) IWD30 28 1/2" (72.4 cm) 9 1/8" (23.2 cm) 1 1/16" (2.7 cm) MRWD27 25 1/2" (64.8 cm) 27" (68.6 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* MRWD30 28 1/2" (72.4 cm) 30" (76.2 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* MWDH27 25 1/2" (64.8 cm) 27 1/4" (69.2 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* MWDH30 28 1/2" (72.4 cm) 30 1/4" (76.8 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* MWDV27 25 1/2" (64.8 cm) 27 1/4" (69.2 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* MWDV30 28 1/2" (72.4 cm) 30 1/4" (76.8 cm)* 9 1/8" (23.2 cm) 1 1/4" (3.2 cm)* OWD24 22 5/8" (57.5 cm) 24 1/4" (61.6 cm)*** 11 15/16" (30.3 cm) NA Min. Cutout Depth 24" (61.0 cm) 20 1/8" (51.1 cm) * Bare minimum spacing to allow for ventilation and avoid scraping on ERW, EWD, MRW and MWD series models. ** IWD models or OWD24 without the optional front panel kit: The chassis and drawer faceplate are smaller than the cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop. *** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below cutout is 3/4" minimum. See ** above for OWD24 with custom front panel. _a_D_ 5 Install Support Platform in Cabinet __ R__ face I a a a Provide a platform (100 lb. load capacity) within the cabinet upon which the warming drawer will be supported. The platform must be installed level and straight. The top edge of the platform must be flush with the cutout at the front of the cabinet. There are no provisions to level the warming drawer after it has been installed. 3/4" (1.9 cm) thick plywood is recommended. a I I a a a I I a a NOTE: If the drawer is not installed in a level fashion, the drawer may slide open on its own or may not seal tightly, allowing heat to escape and resulting in poor warming drawer performance. Electrical and Environmental Specifications a a Ii Minimum ambient operating temperature: 32°F (0°C). Ii The correct voltage, frequency and amperage must be supplied to the electrical outlet from a grounded, single phase circuit that is protected by a properly sized circuit breaker or time-delay fuse. WARNING The required voltage, frequency and amperage ratings are listed on the product data label. See page 1 for location. IMPORTANT: This appliance is equipped with a three prong grounding electric plug for protection against possible electric shock hazards. It must be plugged into a dedicated, grounded, electrical outlet. If only a two prong electrical outlet is available, it is the responsibility of the customer to have it replaced with a dedicated, properly grounded three prong electrical outlet. To avoid an electric shock hazard, do not under any circumstances: Nominal The warming drawer is supplied with a 40" (101.6 cm) power cord with a three prong grounded plug. Total Connected Use an adapter plug. 0.5 kW (4 Amp.) It is the owner's responsibility to ensure that the electrical outlet is installed by a qualified electrician. The electrical installation must comply with the latest revision of the National Electric Code ANSI/NFPA 70 and local codes and ordinances. Immerse the power cord or plug in water or other liquid. o Connect the appliance to an extension cord. NOTE: Use of a ground fault interrupter (GFt) is not recommended. Load The power supply requirements shown above are for reference only. If they do not agree with those listed on the product data label, use the requirements on the product data label. o Use a power cord that is frayed or damaged. • Supply Requirements 120 Vac, 60 Hz, 15 Amp., dedicated circuit o Cut or remove the third (ground) prong from the power cord. • Electrical • If the electrical service provided does not meet the product specification, or does not conform to the NEC or local standards, do not proceed with the installation. Call a licensed electrician to correct the electrical service before proceeding. • Be certain to locate the electrical outlet in an accessible location, so that the warming drawer may be easily unplugged in the event that service becomes necessary. Keep the electrical cord away from hot surfaces. Three prong plug Three prong grounded outlet 6 _aCD_ WARNING To avoid personal injury caused by the appliance falling forward when the drawer _sopened, secure the chassis to the cabinet and support platform as instructed. Be certain that the power plug is disconnected from the electrical outlet before installation. • Verify that the electrical supply matches the ratings found on the appliance data plate and the installation specifications before proceeding. Installing the Chassis 1. . . Remove the Drawer Remove the drawer from the appliance to allow access to the mounting holes during installation, and to reduce weight: 1. Pull the drawer out to the fully open position. 2. Push in on the locking tab on one side as you pull the drawer up. 3. When the drawer comes loose from the slide, repeat the same process on the opposite side. 4. Grip the drawer on both sides and pull it free. 5. For safety, push both drawer slides into the drawer opening. . Grasp the warming drawer chassis on opposite sides and slide it partially into the cabinet opening. Temporarily support the chassis in place so that it will not tilt or fall. From an adjoining cabinet, reach in behind the drawer and pull the power cord until the plug is next to the electrical outlet. Do not plug in the power cord at this time. After positioning the power cord and plug, slide the chassis completely into the cabinet until the front frame is positioned flush against the cabinet face. Use the screws provided to secure the warming drawer chassis to the cabinet and support platform, insert them into the mounting holes and tighten into place. You may want to drill pilot holes prior to installing the mounting screws. Mounting hole, 9 places STEP 2: Push locking tab Mounting Hole Locations = ERW, EWD, IWD, MRW and MWD Series Models (IWD series models do not have a flange around the edge of the faceplate) Mounting hole, 4 places STEP 3: Pull up on front of drawer I I I I Mounting Hole Locations OWD24 Continued... Style varies, EWD27 shown _a_D_ 7 Re-installing the Drawer . . Towel Rack Installation Pull the drawer slides all the way out of the drawer opening. Gently lower the drawer between the extended slides until it is suspended by them. (OWD24 Only) Model OWD24 is designed so that it can be used as a towel warmer if desired. Other models are not equipped for this application. To use model OWD24 as a towel warmer, you must install the towel rack included with the unit in the bottom of the drawer. 3. Slide the back of the drawer mounting brackets under the drawer mounting clips on the slides. 4. Push one side of the drawer down onto its locking tab, until the tab locks into place. To install the towel rack: 1. Open the drawer completely. Repeat the same process on the opposite side. 2. Insert the towel rack into the drawer in the orientation shown below, . 6. Gently open and close the drawer to make sure that it is properly installed. STEP 3: Slide mounting bracket under clip on slide \ Clip on slide Slide . STEP 4: Push front of drawer down until tabs lock into place 8 _SCD_ Use the clamp and screw included with the rack to attach it to the back of the drawer face as shown below. There is a hole for the screw in the back of the face plate near the bottom. Warming Drawer Control Installation Checklist Verify Warming Drawer Operation WARNING 1. Connect power plug to the electrical outlet. 2. Open the drawer and press the ON/OFF key on the control panel, , 4. Press the PROOF, LOW, MED and HIGH keys each in turn. When you press each key, the indicator directly above it should light. Leave the control panel set to HIGH. Press the SELECT key. The 1 HOUR indicator should light. Press and release the SELECT key three (3) more times. Each time you press the SELECT key, the 2 HOUR, 3 HOUR and 4 HOUR indicator lights should come on. All lights should be on after pressing the SELECT key the third time. 5. Press the "oo" key. The indicator light above it should come on and the 1, 2, 3 and 4 HOUR lights should go out. 6. The warming drawer should begin to heat. You should begin to feel the inside of the drawer begin to heat within five (5) to ten (10) minutes. 7. - To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. - Proper installation is the responsibility of the homeowner. The importance of proper installation of your warming drawer cannot be overemphasized. [] Support platform has been installed according to the instructions on page 6. [] Properly grounded, dedicated, three prong electrical outlet has been installed for the appliance by a licensed electrician. See page 6. [] The chassis has been properly fastened to the support platform and sides of the cabinet. See page 7. [] The drawer has been properly installed. See page 8. [] Model OWD24 for use as towel warmer: The towel rack has been installed. See page 8. When you have determined that the heating element is working, press the ON/OFF key. If the warming drawer does not operate properly, these troubleshooting steps: Panel Layout follow • Verify that the circuit breaker for the electrical outlet is on and not tripped. Make sure the power plug is connected. • Repeat the above tests. • If the appliance still does not work, contact Dacor Distinctive Service at (877) 337-3226. Do not attempt to repair the appliance yourself. Be sure to have the model and serial numbers available when you call. See page 1 for model/serial number location. [] Proper operation has been verified? [] The warranty has been activated on-line or the warranty card filled out completely and mailed? [] Save these instructions for future reference. Dacor is not responsible for the cost of correcting problems resulting from a faulty installation. _a_D_ 9 The Life of the Kitchen? ® Dacor • 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 • Phone: (800) 793-0093 • Fax: (626)403-3130 . Family Owned American Maae • www.Dacor.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 12 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Wed Feb 16 04:22:02 2011 Author : Title : Subject :EXIF Metadata provided by EXIF.tools