Datalogic S r l A056 Industrial PDA User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1544687
Application ID	yrft1HxKuR+qxVpDalfioQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	245.52kB (3069004 bits)
Date Submitted	2011-09-20 00:00:00
Date Available	2011-09-20 00:00:00
Creation Date	2011-08-01 16:13:58
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2011-08-01 16:13:58
Document Title	Microsoft Word - 110801_Joya R2U - User's Manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	dvaccaneo

Datalogic JoyaTM R2U “Ready to
Use”
User’s manual
Datalogic Mobile S.r.l.
Via S. Vitalino 13
40012 - Lippo di Calderara di Reno
Bologna - Italy
Datalogic Joya™ - User's Manual
Ed.: draft 110801
ALL RIGHTS RESERVED
The Datalogic name and logo are registered trademarks of Datalogic S.p.A. in many
countries.
The JOYA name and logo are a trademarks of Datalogic Mobile S.r.l.
All other brand and product names mentioned herein are for identification purposes only and
may be trademarks or registered trademarks of their respective owners.
Datalogic reserves the right to make modifications and improvements without prior
notification.
Datalogic shall not be liable for technical or editorial errors or omissions contained herein,
nor for incidental or consequential damages resulting from the use of this material.
© 2008 Datalogic Mobile S.r.l. • All rights reserved. • Protected to the fullest extent under
U.S. and international laws. • Copying, or altering of this document is prohibited without
express written consent from Datalogic Mobile S.r.l.
CONTENTS
DATALOGIC END USER LICENSE AGREEMENT .......................... V
REFERENCES ................................................................................. 1
Conventions ...................................................................................... 1
Reference Documentation................................................................. 1
SAFETY REGULATIONS ................................................................. 2
General Safety Rules ........................................................................ 2
Bluetooth® Approval ......................................................................... 2
Laser Safety...................................................................................... 3
LED Class ......................................................................................... 7
Radio Compliance............................................................................. 8
SAR Compliance............................................................................... 9
Wireless and Radio Frequencies Warnings..................................... 11
Patents............................................................................................ 14
WEEE Compliance ......................................................................... 14
GENERAL VIEW ............................................................................ 16
1.1
1.2
1.3
1.4
INTRODUCTION............................................................................. 17
Datalogic Joya™ Description .......................................................... 17
Model Description ........................................................................... 17
Package Contents........................................................................... 18
Accessories .................................................................................... 18
2.1
2.2
2.3
CONNECTIONS.............................................................................. 19
USB Connection.............................................................................. 19
WLAN Connection .......................................................................... 20
WPAN Connections ........................................................................ 22
3.1
3.1.1
3.2
3.2.1
3.3
3.3.1
3.4
3.4.1
3.5
3.5.1
3.5.2
3.6
3.6.1
3.6.2
3.6.3
3.6.4
3.6.5
3.7
USE AND FUNCTIONING............................................................... 23
Startup ............................................................................................ 23
Using the Stylus (available only on Joya+TM)................................... 24
Data Capture................................................................................... 25
Laser Data Capture ......................................................................... 25
Description of the Keys ................................................................... 26
Resetting the Joya™....................................................................... 27
Status Indicators ............................................................................. 28
Taskbar........................................................................................... 28
Data Capture Configuration............................................................. 29
Configure ........................................................................................ 29
Capture ........................................................................................... 29
Control Panel .................................................................................. 29
Registry........................................................................................... 29
Files Admin ..................................................................................... 30
Wireless Communications............................................................... 30
Using Summit Radio Card Utility ..................................................... 30
Stylus Calibration (available only on Joya+™)................................. 30
Windows Connections..................................................................... 30
iii
3.7.1
3.7.2
3.7.3
3.8
3.9
Microsoft® ActiveSync®.................................................................. 30
Bluetooth® Manager Device Setup ................................................. 33
FTP Server Setup ........................................................................... 36
Backup Directory File Management................................................. 36
Firmware Update............................................................................. 37
4.1
4.2
4.3
MAINTENANCE .............................................................................. 38
Charging the Battery Pack .............................................................. 38
Replacing the Battery Pack ............................................................. 39
Cleaning the Mobile Computer ........................................................ 42
5.1
5.2
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
5.3.7
5.3.8
5.3.9
5.3.10
5.3.11
5.4
5.4.1
5.4.2
5.4.3
5.4.4
5.5
5.6
5.7
JOYATM CRADLE DISPENSER...................................................... 43
Introduction ..................................................................................... 43
Accessories .................................................................................... 43
Installation requirements ................................................................. 44
Base Unit Construction Details........................................................ 44
JoyaTM Cradle Dispenser Supports ................................................. 44
Internal Cabinet Space and Openings............................................. 44
Anchoring and Maintenance Issues................................................. 44
Power Supply Positioning and Cooling ............................................ 44
AC Power Cabling ........................................................................... 44
Wiring ............................................................................................. 44
Cable to Power Supply Connection ................................................. 44
Affixing Cables to Cabinet ............................................................... 44
Safety Precautions .......................................................................... 44
Connection to AC Line Voltage ....................................................... 45
JoyaTM cradle dispenser firmware ................................................... 46
APC installation............................................................................... 46
Starting program ............................................................................. 46
Reading firmware version................................................................ 47
Firmware update procedure ............................................................ 48
JoyaTM – JoyaTM cradle dispenser connection ................................. 48
Configuration................................................................................... 49
Use and functioning ........................................................................ 49
6.1
JOYA /JOYA+ TECHNICAL FEATURES................................. 50
Technical Data ................................................................................ 50
TEST CODES ................................................................................. 51
TM
TM
GLOSSARY .................................................................................... 53
INDEX............................................................................................. 55
iv
DATALOGIC END USER LICENSE AGREEMENT
BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR BY USING DATALOGIC
EQUIPMENT THAT INCLUDES THIS SOFTWARE, YOU ARE CONSENTING TO BE
BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF
THIS AGREEMENT, THEN DO NOT DOWNLOAD, INSTALL, USE THE SOFTWARE NOR
DATALOGIC EQUIPMENT.
The following terms and conditions govern your use of the Software except to the extent that a particular
program (a) is the subject of a separate written agreement with Datalogic or (b) includes a separate “clickon” license agreement as part of the installation and/or download process. Should a conflict arise
between the provisions of the foregoing documents, the order of precedence shall be (1) the written
agreement, (2) the click-on agreement, and (3) this agreement (“Agreement”).
1. License. Subject to the terms and conditions of and except as otherwise provided in this Agreement,
Datalogic Mobile S.r.l. (“Datalogic”) and its suppliers grant to Customer (“Customer”) a nonexclusive and
nontransferable license to use the specific program modules, feature set(s) or feature(s) in object code
form only as well as associated media, printed materials and “online” or electronic documentation (the
“Software”) for which Customer has paid, if required, the license fees. The Software is licensed not sold.
The license shall be subject to each of the following limitations:
•
Unless otherwise expressly provided in the documentation, Customer shall use the Software solely
as embedded in, for execution on, or (where the applicable documentation permits installation on
non-Datalogic equipment) for communication with Datalogic equipment owned or leased by
Customer;
•
Customer’s use of the Software shall be limited to use on a single hardware chassis, on a single
central processing unit, as applicable, or use on such greater number of chassis or central
processing units as Customer may have paid Datalogic the required license fee; and
•
Customer’s use of the Software shall also be limited, as applicable and set forth in Customer’s
purchase order or in Datalogic’s product catalog, user documentation, or web site, to a maximum
number of (a) seats (i.e. users with access to the installed Software), (b) concurrent users,
sessions, ports, and/or issued and outstanding IP addresses, and/or (c) central processing unit
cycles or instructions per second. Customer’s use of the Software shall also be limited by any other
restrictions set forth in Customer’s purchase order or in Datalogic’s product catalog, user
documentation or web site for the Software.
2. General Limitations. Except as otherwise expressly provided under this Agreement, Customer shall
have no right, and Customer specifically agrees not to (i) transfer, assign or sublicense its license rights
to any other person, or use the Software on unauthorized or secondhand Datalogic equipment, and any
such attempted transfer, assignment or sublicense shall be void; (ii) correct errors to or otherwise modify
or adapt the Software or create derivative works based upon the Software, or to permit third parties to do
the same; or (iii) decompile, decrypt, reverse engineer, disassemble or otherwise reduce the Software to
human-readable form to gain access to trade secrets or confidential information in the Software. To the
extent required by law, at Customer's request, Datalogic shall provide Customer with the interface
information needed to achieve interoperability between the Software and another independently created
program, upon payment of Datalogic's applicable fee. Customer shall observe strict obligations of
confidentiality with respect to such information.
3. Upgrades and Additional Copies. For purposes of this Agreement, “Software” shall include (and the
terms and conditions of this Agreement shall apply to) any upgrades, updates, bug fixes or modified
versions (collectively, “Upgrades”) or backup copies of the Software licensed or provided to Customer by
Datalogic or an authorized distributor for which Customer has paid the applicable license fees.
Notwithstanding any other provision of this Agreement: (1) customer has no license or right to use any
such additional copies or upgrades unless customer, at the time of acquiring such copy or upgrade,
already holds a valid license to the original Software and has paid the applicable fee for the upgrade, if
required; (2) use of upgrades is limited to Datalogic equipment for which customer is the original end
user, purchaser or lessee or who otherwise holds a valid license to use the Software which is being
upgraded; and (3) use of additional copies is limited to backup purposes only.
4. Proprietary Notices. Customer agrees to maintain and reproduce all copyright and other proprietary
notices on all copies, in any form, of the Software in the same form and manner that such copyright and
other proprietary notices are included on the Software. Except as expressly authorized in this Agreement,
Customer shall not make any copies or duplicates or any Software without the prior written permission of
Datalogic. Customer may make such backup copies of the Software as may be necessary for Customer’s
lawful use, provided Customer affixes to such copies all copyright, confidentiality, and proprietary notices
that appear on the original.
5. Protection of Information. Customer agrees that aspects of the Software and associated
documentation, including the specific design and structure of individual programs, constitute trade secrets
and/or copyrighted material of Datalogic. Customer shall not disclose, provide, or otherwise make
available such trade secrets or copyrighted material in any form to any third party without the prior written
consent of Datalogic. Customer shall implement reasonable security measures to protect such trade
secrets and copyrighted material. Software and documentation shall remain solely property of Datalogic.
6. Limited Warranty. If Customer obtained the Software directly from Datalogic, then Datalogic warrants that
during the Warranty Period (as defined below): (i) the media on which the Software is furnished will be free of
defects in materials and workmanship under normal use; and (ii) the Software will substantially conform to its
published specifications. The “Warranty Period” means a period beginning on the date of Customer’s receipt of
the Software and ending on the later of (a) ninety (90) days from the date of initial shipment of the Software by
Datalogic, or (b) the end of the minimum period required by the law of the applicable jurisdiction. The limited
warranties extend only to Customer as the original licensee. Customer's sole and exclusive remedy and the
entire liability of Datalogic and its suppliers under these limited warranties will be, at Datalogic’s sole option,
repair or replacement of the Software if reported (or, upon request, returned) to Datalogic. Except as expressly
granted in this Agreement, the Software is provided AS IS and with all faults. Datalogic does not warrant that
the Software is error free or that Customer will be able to operate the Software without problems or
interruptions. In addition, due to the continual development of new techniques for intruding upon and attacking
networks, Datalogic does not warrant that the Software or any equipment, system or network on which the
Software is used will be free of vulnerability to intrusion or attack. This warranty does not apply if the Software
(a) is licensed for beta, evaluation, testing or demonstration purposes for which Datalogic does not receive a
license fee, (b) has been altered, except by Datalogic, (c) has not been installed, operated, repaired, or
maintained in accordance with instructions supplied by Datalogic, (d) has been subjected to abnormal physical
or electrical stress, misuse, negligence, or accident, or (e) is used in ultra hazardous activities. If Customer
obtained the Software from a Datalogic reseller, the terms of any warranty shall be as provided by such
distributor, and Datalogic provides Customer no warranty with respect to such Software. The Software may
contain support for programs written in Java. Java technology is not fault tolerant and is not designed,
manufactured, or intended for use or resale as online control equipment in hazardous environments requiring
fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication
systems, air traffic control, direct life support machines, or weapons systems, in which the failure of Java
technology could lead directly to death, personal injury, or severe physical or environmental damage. Microsoft
Inc. has contractually obligated Datalogic to make this disclaimer.
7. Disclaimer of Warranties. Except as specified in this warranty, all expressed or implied conditions,
representations, and warranties including, without limitation, any implied warranty or condition of
merchantability, fitness for a particular purpose, non-infringement, satisfactory quality or arising from a course
of dealing, usage, or trade practice, are hereby excluded to the extent allowed by applicable law. To the extent
that an implied warranty cannot be excluded, such warranty is limited in duration to the warranty period.
8. Disclaimer of Liabilities. In no event will Datalogic or its suppliers be liable for any lost revenue, profit,
or data, or for special, indirect, consequential, incidental, or punitive damages however caused and
arising out of the use of or inability to use the Software even if Datalogic has been advised of the
possibility of such damages. In no event shall Datalogic or its suppliers' liability to customer, whether in
contract, tort (including negligence), or otherwise, exceed the price paid by customer. The foregoing
limitations shall apply even if the above-stated warranty fails of its essential purpose.
9. Term and Termination. This Agreement is effective until terminated. Customer may terminate this
Agreement at any time by destroying all copies of Software including any documentation. Customer’s
license rights under this Agreement will terminate immediately without notice from Datalogic if Customer
fails to comply with any provision of this Agreement. Upon termination, Customer must destroy all copies
of Software in its possession or control.
10. Customer Records. Customer grants to Datalogic and its independent accountants the right to
examine Customer’s books, records and accounts during Customer’s normal business hours to verify
compliance with this Agreement. In the event such audit discloses non-compliance with this Agreement,
Customer shall promptly pay to Datalogic the appropriate license fees.
11. General Provisions. This Agreement shall be governed by and construed in accordance with the
laws of Italy. All disputes arising out of or in connection with this Agreement will be subject to the
exclusive jurisdiction of the competent Court of the place where Datalogic has its registered office. If any
portion hereof is found to be void or unenforceable, the remaining provisions of this Agreement shall
remain in full force and effect. Except as expressly provided herein, this Agreement constitutes the entire
agreement between the parties with respect to the license of the Software and supercedes any conflicting
or additional terms contained in the purchase order.
vi
INTRODUCTION
REFERENCES
CONVENTIONS
This manual uses the following conventions:
“User” refers to anyone using a Datalogic Joya™ mobile computer.
“Mobile computer” and "Datalogic Joya™" refer to Datalogic Joya™ mobile
computer.
“You” refers to the System Administrator or Technical Support person using this
manual to install, configure, operate, maintain or troubleshoot a Datalogic
Joya™ mobile computer.
“Cradle” refers to Datalogic Joya™ Cradle Dispenser.
REFERENCE DOCUMENTATION
For further information regarding Datalogic Joya™ refer to the SDK Help onLine.
DATALOGIC JOYA™
SAFETY REGULATIONS
NOTE
Read this manual carefully before performing any type of
connection to the Datalogic Joya™ mobile computer.
The user is responsible for any damages caused by incorrect
use of the equipment or by inobservance of the indication
supplied in this manual.
GENERAL SAFETY RULES
−
Use only the components supplied by the manufacturer for the specific
Datalogic Joya™ being used.
−
Do not attempt to disassemble the Datalogic Joya™ mobile computer, as
it does not contain parts that can be repaired by the user. Any tampering
will invalidate the warranty.
−
When replacing the battery pack or at the end of the operative life of the
Datalogic Joya™ mobile computer, disposal must be performed in
compliance with the laws in force.
−
Before using the device and the battery pack, see par. 4.2 and read every
warnings about the device and the battery pack.
−
Do not submerge the Datalogic Joya™ in liquid products.
−
The Datalogic Joya™ is designed and labelled to be compliant with laws,
rules and regulations in force in the countries where it is sold.
−
For further information, refer to this manual and to the Datalogic Mobile
web site: www.mobile.datalogic.com.
BLUETOOTH® APPROVAL
This product is equipped with the following certified Bluetooth module:
Product Name: DL_NEXTGEN_BT
Bluetooth ID: B016669
Product ID: DL_NEXTGEN_BT
INTRODUCTION
LASER SAFETY
The laser light is visible to the human eye and is emitted from the window
indicated in the figure.
Die Laserstrahlung
ist für das
menschliche Auge
sichtbar und wird am
Strahlaustrittsfenster
ausgesendet (siehe
Bild).
Le rayon laser est
visible à l'oeil nu et il
est émis par la
fenêtre désignée sur
l'illustration dans la
figure.
LUCE LASER
NON FISSARE IL
FASCIO
APPARECCHIO
LASER DI CLASSE 2
MASSIMA POTENZA
DI USCITA: 2mW
LUNGHEZZA D'ONDA
EMESSA: 650nm
CONFORME A EN
60825-1 (2001)
LASERSTRAHLUNG
NICHT IN DER STRAHL
BLINKEN
PRODUKT DER
LASERKLASSE 2
MAXIMALE
AUSGANGLEISTUNG:
2mW WELLENLÄNGE:
650nm
ENTSPR. EN 60825-1
(2001)
La luce laser è
visibile all'occhio
umano e viene
emessa dalla
finestra indicata
nella figura.
RAYON LASER
EVITER DE
REGARDER
LE RAYON
APPAREIL LASER DE
CLASSE 2
PUISSANCE DE
SORTIE: 2mW
LONGUER D'ONDE
EMISE: 650nm
CONFORME A EN
60825-1 (2001)
La luz láser es
visible al ojo
humano y es
emitida por la
ventana indicada
en la figura.
RAYO LÁSER
NO MIRAR FIJO EL
RAYO
APARATO LÁSER DE
CLASE 2
MÁXIMA POTENCIA
DE SALIDA: 2mW
LONGITUD DE ONDA
EMITIDA: 650nm
CONFORME A EN
60825-1
(2001)
DATALOGIC JOYA™
ENGLISH
The following information is provided to comply with the rules imposed by
international authorities and refers to the correct use of your mobile computer.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR
1040 Subchapter J and EN 60825-1:2001 at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.
CAUTION
CAUTION
Do not attempt to open or otherwise service any
components in the optics cavity. Opening or servicing
any part of the optics cavity by unauthorized personnel
may violate laser safety regulations. The optics system is
a factory only repair item.
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in exposure to hazardous visible laser light.
The product utilizes a low-power laser diode. Although staring directly at the
laser beam momentarily causes no known biological damage, avoid staring at
the beam as one would with any very strong light source, such as the sun.
Avoid that the laser beam hits the eye of an observer, even through reflective
surfaces such as mirrors, etc.
CAUTION
Use of optical systems with the scanner will increase eye
hazard. Optical instruments include binoculars,
microscopes, eye glasses and magnifying glasses.
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità
internazionali e si riferiscono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser
alla data di produzione: CDRH 21 CFR 1040 sezione J e EN 60825-1:2001.
Non si rende mai necessario aprire l’apparecchio per motivi di installazione,
utilizzo o manutenzione.
CAUTION
Non tentare di accedere allo scomparto contenete i
componenti ottici o di farne la manutenzione.
L’apertura dello scomparto, o la manutenzione di qualsiasi
parte ottica da parte di personale non autorizzato, potrebbe
violare le norme della sicurezza. Il sistema ottico può essere
riparato solamente alla fabbrica.
INTRODUCTION
ATTENZIONE
L'utilizzo di procedure o regolazioni differenti da quelle
descritte
nella
documentazione
può
provocare
un'esposizione pericolosa a luce laser visibile.
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti
danni riportati dall’occhio umano in seguito ad una esposizione di breve durata,
evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente
di luminosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser
negli occhi di un osservatore, anche attraverso superfici riflettenti come gli
specchi.
CAUTION
L’uso di strumenti ottici assieme allo scanner può aumentare
il pericolo di danno agli occhi. Tali strumenti ottici includono
cannocchiali, microscopi, occhiali e lenti di ingrandimento.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein,
die von internationalen Behörden auferlegt wurden, und sie beziehen sich auf
den korrekten Gebrauch vom Terminal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1:2001
und CDRH 21 CFR 1040 Subchapter J Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations-, und
Wartungs-Arbeiten zu öffnen.
CAUTION
ACHTUNG
Unter keinen Umständen darf versucht werden, die
Komponenten im Optikhohlraum zu öffnen oder auf
irgendwelche andere Weise zu warten. Das Öffnen bzw.
Warten der Komponenten im Optikhohlraum durch
unbefugtes Personal verstößt gegen die LaserSicherheitsbestimmungen. Das Optiksystem darf nur
werkseitig repariert werden.
Jegliche Änderungen am Gerät sowie Vorgehensweisen,
die nicht in dieser Betriebsanleitung beschrieben werden,
können ein gefährliches Laserlicht verursachen.
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden
von kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere
DATALOGIC JOYA™
Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen
(z.B. die Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen
eines Beobachters, noch gegen reflektierende Oberflächen zu richten.
CAUTION
Die Verwendung von Optiksystemen mit diesem Scanner
erhöht die Gefahr einer Augenbeschädigung.
Zu optischen Instrumenten gehören unter anderem
Ferngläser, Mikroskope, Brillen und Vergrößerungsgläser.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les
autorités internationales et se réfèrent à une correcte utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de
fabrication: CDRH 21 CFR 1040 sous-chapitre J et EN 60825-1:2001.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou
l’entretien.
CAUTION
ATTENTION
Ne pas essayer d’ouvrir ou de réparer les composants de la
cavité optique. L’ouverture de la cavité optique ou la
réparation de ses composants par une personne non
qualifiée peut entraîner le nonrespect des règles de sécurité
relatives au laser. Le système optique ne peut être réparé
qu’en usine.
L'utilisation de procédures ou réglages différents de ceux
donnés ici peut entraîner une dangereuse exposition à
lumière laser visible.
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été
constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement
le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter
aussi de diriger le rayon vers les yeux d’un observateur, même à travers des
surfaces réfléchissantes (miroirs, par exemple).
CAUTION
L’utilisation d’instruments optiques avec le scanneur
augmente le danger pour les yeux. Les instruments
optiques comprennent les jumelles, les microscopes, les
lunettes et les verres grossissants.
INTRODUCTION
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las
disposiciones de las autoridades internacionales y se refieren al uso correcto
del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a
la fecha de producción: CDRH 21 CFR 1040 Sección y EN 60825-1:2001.
No es necesario abrir el aparato para la instalación, la utilización o la
manutención.
CAUTION
ATENCIÓN
No intente abrir o de ninguna manera dar servicio a ninguno
de los componentes del receptáculo óptico. Abrir o dar
servicio a las piezas del receptáculo óptico por parte del
personal no autorizado podría ser una violación a los
reglamentos de seguridad. El sistema óptico se puede
reparar en la fábrica solamente.
La utilización de procedimientos o regulaciones diferentes
de aquellas describidas en la documentación puede causar
una exposición peligrosa a la luz láser visible.
El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los
ojos humanos a consecuencia de una exposición de corta duración. Eviten de
mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad
intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los
ojos de un observador, también a través de superficies reflectantes como los
espejos.
CAUTION
El uso de sistemas ópticos con el escáner aumentará el
riesgo de daños oculares. Los instrumentos ópticos incluyen
binoculares, microscopios, lentes y lupas.
LED CLASS
According to EN 60825-1:2001, the Datalogic Joya™ models which use the
good read spot LED are also CLASS 1 LED PRODUCTS.
APPARECCHIO LED CLASSE 1
PRODUKT LED KLASSE 1
PRODUIT LED DE CLASSE 1
PRODUCTO LED DE CLASE 1
DATALOGIC JOYA™
RADIO COMPLIANCE
In radio systems configured with mobile computers and access points, the
frequencies to be used must be allowed by the spectrum authorities of the
specific country in which the installation takes place. Be absolutely sure that the
system frequencies are correctly set to be compliant with the spectrum
requirements of the country.
Information for the User
ENGLISH
Contact the competent authority responsible for the management of radio
frequency devices of your country to verify any possible restrictions or licenses
required.
Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for
further information.
ITALIANO
Prendi contatto con l'autorità competente per la gestione degli apparati a radio
frequenza del tuo paese, per verificare eventuali restrizioni o licenze. Ulteriori
informazioni sono disponibili sul sito:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
FRANÇAIS
Contactez l'autorité compétente en la gestion des appareils à radio fréquence
de votre pays pour vérifier d'éventuelles restrictions ou licences. Pour tout
renseignement vous pouvez vous adresser au site web:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
DEUTSCH
Wenden Sie sich an die für Radiofrequenzgeräte zuständige Behörde Ihres
Landes, um zu prüfen ob es Einschränkungen gibt, oder eine Lizenz
erforderlich ist. Weitere Informationen finden Sie auf der Web Seite:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
ESPAÑOL
Contacta la autoridad competente para la gestión de los dispositivos de radio
frecuencia de tu país, para verificar cualesquiera restricciones o licencias
posibles requerida. Además se puede encontrar mas información en el sitio
Web:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
INTRODUCTION
FCC COMPLIANCE
FCC Regulations:
• This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
• This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user‘s authority to operate the equipment.
• The antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
INDUSTRY CANADA COMPLIANCE
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
The County Code Selection feature is disabled for products marketed in the
US/Canada.
This EUT is compliant with SAR for general population/uncontrolled exposure
limits in IC RSS-102 and had been tested in accordance with the measurement
methods and procedures specified in IEEE 1528. This equipment should be
DATALOGIC JOYA™
installed and operated with minimum distance 1,5cm between the radiator &
your body.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
RF EXPOSURE INFORMATION (SAR)
This model device meets the government’s requirements for exposure to radio
waves. This device is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
The exposure standard for wireless devices employs a unit of measurement
known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC
is 1.6W/kg. *Tests for SAR are conducted using standard operating positions
accepted by the FCC with the device transmitting at its highest certified power
level in all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the device while operating
can be well below the maximum value. This is because the device is designed
to operate at multiple power levels so as to use only the poser required to reach
the network. In general, the closer you are to a wireless base station antenna,
the lower the power output.
While there may be differences between the SAR levels of various devices and
at various positions, they all meet the government requirement.
The FCC has granted an Equipment Authorization for this model device with all
reported SAR levels evaluated as in compliance with the FCC RF exposure
guidelines. SAR information on this model device is on file with the FCC and
can be found under the Display Grant section of http://www.fcc.gov/oet/fccid
after searching on the below FCC IDs:
FCC ID: U4G-A056 (for JOYA + A with BT and WLAN)
Contains FCC ID: U4G-004W (for JOYA A and JOYA + A with WLAN only)
This device is compliant with SAR for general population /uncontrolled
exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance
with the measurement methods and procedures specified in OET Bulletin 65
Supplement C.
SAR COMPLIANCE
This product has been tested and found to comply with the following standards:
•
10
The portable device Joya + A from Datalogic (FCC ID: U4GA056) is
in compliance with the IC RSS 102 Issue 4 [RSS 102] and Federal
INTRODUCTION
Communications Commission (FCC) Guidelines
[OET 65] for
uncontrolled exposure. SAR assessment in body worn
was
conducted with the back of the device in direct contact against
the flat phantom.
•
For the used worst case positions, the portable device
Joya
from
Datalogic (Contains FCC ID: U4G004W) is in
compliance with the IC RSS 102 Issue 4 [RSS l02] and Federal
Communications Commission (FCC) Guidelines [OET 65] for
uncontrolled exposure. SAR assessment in body worn was
conducted with the back of the device in direct contact against the
flat phantom.
•
EN 62311:2008 Assessment of electronic and electrical equipment
related to human exposure restrictions for electromagnetic fields (0
Hz – 300 GHz)
WIRELESS AND RADIO FREQUENCIES WARNINGS
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications or attachments could
damage the product and may violate laws and regulations.
WARNING
Most modern electronic equipment is shielded from RF signals.
However, certain electronic equipment may not be shielded
against the RF signals generated by Datalogic Joya™.
WARNING
Datalogic recommends persons with pacemakers or other
medical devices to follow the same recommendations provided
by Health Industry Manufacturers Associations for mobile
phones.
11
1
WARNING
WARNING
DATALOGIC JOYA™
Persons with pacemakers:
•
Should ALWAYS keep this device more than twenty five
(25) cm from their pacemaker and/or any other medical
device;
•
Should not carry this device in a breast pocket;
•
Should keep the device at the opposite side of the
pacemaker and/or any other medical device;
•
Should turn this device OFF or move it immediately AWAY
if there is any reason to suspect that interference is taking
place.
•
Should ALWAYS read pacemaker or any other medical
device guides or should consult the manufacturer of the
medical device to determine if it is adequately shielded
from external RF energy.
In case of doubt concerning the use of wireless devices with an
implanted medical device, contact your doctor.
Turn this device OFF in health care facilities when any
regulations posted in these areas instruct you to do so.
Hospitals or health care facilities may use equipment that could
be sensitive to external RF energy.
WARNING
Do not use the device while driving: give full attention to driving
— driving safely is your first responsibility.
The device is not designed to be used with a GPS system. Any
program installed without Datalogic authorization may affect the
device's safety.
WARNING
RF signals may affect improperly installed or inadequately
shielded electronic systems in motor vehicles. Check with the
manufacturer or its representative regarding your vehicle. You
should also consult the manufacturer of any equipment that has
been added to your vehicle.
WARNING
An air bag inflates with great force. DO NOT place objects,
including either installed or portable wireless equipment, in the
area over the air bag or in the air bag deployment area. If
vehicle’s wireless equipment is improperly installed and the air
bag inflates, serious injury could result.
Turn off the device when in any area with a potentially
explosive atmosphere. Observe restrictions and follow closely
any laws, regulations, warnings and best practices on the use
of radio equipment near fuel storage areas or distribution fuel
12
INTRODUCTION
WARNING
areas, chemical plants or where some operation involves use of
explosive materials.
Do not store or carry flammable liquids, explosive gases or
materials with the device or its parts or accessories.
Areas with a potentially explosive atmosphere are often, but not
always, clearly marked or showed.
Sparks in such areas could cause an explosion or fire, resulting
in injury or even death.
13
1
DATALOGIC JOYA™
PATENTS
This product is covered by one or more of the following patents.
Design Pat.: EP 891,544; AU 323,628; US D 613,289 S; ZL 200830146270.9.
U.S. Pat. Nos: 5,992,740; 6,808,114 B1; 6,997,385 B2; 7,387,246 B2;
7,620,475 B2.
European Pat. Nos: 789,315 B1; 1,128,315 B1; 1,396,811 B1; 1,413,971 B1.
Additional patents pending.
WEEE COMPLIANCE
Informazione degli utenti ai sensi della Direttiva Europea 2002/96/EC
L’apparecchiatura che riporta il simbolo del bidone barrato deve essere
smaltita, alla fine della sua vita utile, separatamente dai rifiuti urbani.
Smaltire l’apparecchiatura in conformità alla presente Direttiva consente di:
evitare possibili conseguenze negative per l’ambiente e per la salute
umana che potrebbero invece essere causati dall’errato smaltimento
dello stesso;
recuperare materiali di cui è composto al fine di ottenere un
importante risparmio di energia e di risorse.
Per maggiori dettagli sulle modalità di smaltimento, contattare il Fornitore dal
quale è stata acquistata l’apparecchiatura o consultare la sezione dedicata sul
sito www.mobile.datalogic.com.
Information for the user in accordance with the European Commission
Directive 2002/96/EC
At the end of its useful life, the product marked with the crossed out wheeled
wastebin must be disposed of separately from urban waste.
Disposing of the product according to this Directive:
avoids potentially negative consequences to the environment and
human health which otherwise could be caused by incorrect disposal
enables the recovery of materials to obtain a significant savings of
energy and resources.
For more detailed information about disposal, contact the supplier that provided
you with the product in question or consult the dedicated section at the website
www.mobile.datalogic.com.
14
INTRODUCTION
Information
2002/96/EC
aux
utilisateurs
concernant
la
Directive
Européenne
Au terme de sa vie utile, le produit qui porte le symbole d'un caisson à ordures
barré ne doit pas être éliminé avec les déchets urbains.
Éliminer ce produit selon cette Directive permet de:
éviter les retombées négatives pour l'environnement et la santé
dérivant d'une élimination incorrecte
récupérer les matériaux dans le but d'une économie importante en
termes d'énergie et de ressources
Pour obtenir des informations complémentaires concernant l'élimination,
veuillez contacter le fournisseur auprès duquel vous avez acheté le produit ou
consulter la section consacrée au site Web www.mobile.datalogic.com.
Información para el usuario de accuerdo con la Directiva Europea
2002/96/CE
Al final de su vida útil, el producto marcado con un simbolo de contenedor de
bassura móvil tachado no debe eliminarse junto a los desechos urbanos.
Eliminar este producto de accuerdo con la Directiva permite de:
evitar posibles consecuencias negativas para el medio ambiente y la
salud derivadas de una eliminación inadecuada
recuperar los materiales obteniendo así un ahorro importante de
energía y recursos
Para obtener una información más detallada sobre la eliminación, por favor,
póngase en contacto con el proveedor donde lo compró o consultar la sección
dedicada en el Web site www.mobile.datalogic.com.
Benutzerinformation bezüglich Richtlinie 2002/96/EC der europäischen
Kommission
Am Ende des Gerätelebenszyklus darf das Produkt nicht über den städtischen
Hausmüll entsorgt werden. Eine entsprechende Mülltrennung ist erforderlich.
Beseitigung des Produkts entsprechend der Richtlinie:
verhindert negative Auswirkungen für die Umwelt und die Gesundheit
der Menschen
ermöglicht die Wiederverwendung der Materialien und spart somit
Energie und Resourcen
Weitere Informationen zu dieser Richtlinie erhalten sie von ihrem Lieferanten
über den sie das Produkt erworben haben, oder besuchen sie unsere Hompage
unter www.mobile.datalogic.com.
15
DATALOGIC JOYA™
GENERAL VIEW
A) Display*
B) 6 keys keyboard
C) TTL Serial connector
D) Bumper
E) Cold reset Hole
F) Neck Strip Anchor
*Remove protective film cover before use
16
G) Loudspeaker
H) Micro USB
I) Laser window
INTRODUCTION
1.1
INTRODUCTION
DATALOGIC JOYA ™ DESCRIPTION
The Datalogic Joya ™ is a pocket-sized Windows powered mobile computer.
This extremely compact, lightweight, and versatile device, combines fully
integrated automatic data capture (1D bar code) and wireless communication
capabilities, supporting nearly any application.
The Datalogic Joya™ system architecture is based on the blend of Intel XScale series processors coupled with the Windows CE operating system and it
was developed to meet the most demanding customer needs.
A huge quantity of on-board memory is available. it enables the user to adapt
the terminal for any specific need.
Thanks to its great ergonomics and the state of the art architecture, the
Datalogic Joya™ is the right answer to enhance your business opportunities.
1.2
MODEL DESCRIPTION
For further details about the Datalogic Joya™ models refer to the web site:
http://www.joya.datalogic.com.
17
DATALOGIC JOYA™
1.3
PACKAGE CONTENTS
The Datalogic Joya™ package contains:
1 Datalogic Joya™ mobile computer
−
Remove all the components from their packaging; check their integrity and
congruity with the packing documents.
Keep the original packaging for use when sending products
to the technical assistance center. Damage caused by
improper packaging is not covered under the warranty.
CAUTION
Rechargeable battery packs are not initially charged.
Therefore the initial operation to perform is to charge them.
NOTE
1.4
ACCESSORIES
Cradle
912201000 Datalogic Joya™ Cradle Dispenser
Batteries
91ACC1055 Datalogic Joya™ Battery Pack (10 pcs.)
Cradle Accessories
91ACC1000 Power Supply 12V 300W
91ACC0730 Power Junction Cable I90x/3 Cradle (8 pcs.)
91ACC0650 Term. Unlock Magnets (5 pcs.)
Various
94ACC1328 Datalogic Joya™ Stylus Pens (10 pcs)
91ACC1056 Datalogic Joya™ trolley holder (60 pcs.)
91ACC1057 Datalogic Joya™ checkout holder
Use only a Datalogic Mobile-approved power supply and cables.
Use of an alternative power supply will invalidate any approval
given to this device and may be dangerous.
NOTE
18
CONNECTIONS
2.1
CONNECTIONS
USB CONNECTION
You can use any standard micro USB cable (with length less than 3m) to
directly connect the Datalogic Joya™ to a host computer to transfer data
through the USB interface.
Key:
A)
Host Computer
B)
Standard Micro USB cable type USB A – micro USB B
C)
Datalogic Joya™
19
DATALOGIC JOYA™
2.2
WLAN CONNECTION
Datalogic Joya™ Wi-Fi 802.11 a/b/g radio models can communicate with the
host using the on-board radio frequency component and an Access Point
connected to the host computer.
To launch this utility you can tap the specific icon if it's visible on the taskbar or
you can open Connections folder or Control Panel from desktop and select the
'Summit Client Utility' icon.
Key:
20
A)
Datalogic Joya™
B)
Access Point
C)
Host – Application Server
CONNECTIONS
Wi-Fi module is on by default, in order to avoid wasting
energy, you can switch it off using the Wireless
Communications applet.
NOTE
NOTE
NOTE
Suspending the terminal powers off the 802.11b/g radio and
drops the radio connection. When the terminal resumes,
depending on the radio power mode and security protocol
selected, it may take up to 30 seconds for the 802.11b/g
radio driver to re-associate the radio to the network.
Area coverage and radio performance may vary, due to
environmental conditions, access points types or interference
caused by other devices (microwave ovens, radio
transmitters, etc.)
21
DATALOGIC JOYA™
2.3
WPAN CONNECTIONS
Bluetooth Datalogic Joya™ mobile computer models can communicate with a
Bluetooth device, such as a printer, within a range of 10 m, using the onboard Bluetooth module.
Key:
A)
Datalogic Joya™
B)
Bluetooth printer
NOTE
NOTE
In order to avoid wasting energy, the Bluetooth® module is
off by default. If you need to have Bluetooth® working, the
module must be powered on using the Wireless
Communications applet (see par. 0), and perform the
Discovery procedure (see par. 3.6.2).
Suspending the terminal powers off the Bluetooth radio and
drops the piconet (Bluetooth connection). When the
terminal resumes, it takes approximately 10 seconds for the
Bluetooth radio driver to re-initialize the radio.
Area coverage and Bluetooth radio performance may vary,
due to environmental conditions or interference caused by
other devices (microwave ovens, radio transmitters, etc.), etc.
NOTE
22
USE AND FUNCTIONING
USE AND FUNCTIONING
The use of the Datalogic Joya™ depends on the application software loaded.
However there are several parameters that can be set and utilities that can be
used to perform some basic functions such as data capture, communications,
file management, etc.
3.1
STARTUP
The Datalogic Joya™ turns on when a charged battery pack is inserted.
As soon as the mobile computer is on, the Windows desktop configuration will
appear on the screen. Wait a few seconds before starting any activity so that
the mobile computer completes its startup procedure.
The mobile computer goes into power-off (low power with display and keyboard
backlight off), when it is no longer used for more than a programmable timeout,
which is defined in the POWER applet of the Control Panel. In this mode it can
be awakened (resuming operation) pressing the “Up” Key.
The mobile computer can also be awakened or turned off
by the application program.
NOTE
23
DATALOGIC JOYA™
3.1.1
TM
Using the Stylus (available only on Joya+ )
The stylus selects items and enters information. The stylus functions like a
mouse.
Double Tap:
Touch the screen twice with the stylus to open items and
select options.
Drag:
Hold the stylus on the screen and drag across the screen to
select text and images. Drag in a list to select multiple items.
Tap-andhold:
Tap and hold the stylus on an item to see a list of actions
available for that item. On the pop-up menu that appears,
tap the action you want to perform.
To recalibrate the touch screen use the Stylus Applet
Use only original Datalogic styluses supplied with the product
itself.
CAUTION
In
harsh
applications,
use
of
screen
protectors
should be taken into consideration, in order to extend the
touch screen operating life.
To prevent damage to the screen, do not use sharp devices or
any device other than the Datalogic Mobile-provided stylus.
Do not apply not necessary high pressures on the screen.
For applications where an intensive use of the touch screen is
foreseen, please consider that touch screen components are
subject to progressive wear.
24
USE AND FUNCTIONING
3.2
DATA CAPTURE
To capture data first of all select the barcode icon on the bottom-right side of
the
display and tap the 'Capture' menu item then proceed with the following
directions.
To configure and enable data capture parameters refer to par. 3.5.
3.2.1
Laser Data Capture
To scan barcodes, point the Datalogic Joya™ laser model onto the code from a
distance within the reading range while pressing the “Up” key.
The lighted band emitted by the laser must completely intercept the barcode as
shown in the figure below. If enabled, the emission of an acoustic signal will
indicate that the scan has taken place correctly.
25
DATALOGIC JOYA™
3.3
DESCRIPTION OF THE KEYS
The Datalogic Joya™ provides a 6-key keyboard. The following image shows
this keyboard.
Main Keys Function
+ ”: it corresponds to ArrowUp Key.
Key “ - ”: it corresponds to ArrowDown Key.
Key “
Key “ Left
Key “ Right
”: it corresponds to F1 (Function1) Key.
”: it corresponds to F2 (Function2) Key.
= ”: it corresponds to ESC Key.
Key “ e ” : it corresponds to ENTER Key.
Key “
26
USE AND FUNCTIONING
3.3.1
Resetting the Joya™
There are two reset methods for the Joya™.
A warm boot terminates an unresponsive application and clears the working
RAM, but preserves both the file system and the registry.
A cold boot forces all applications to close and clears working RAM and files
not resident on the persistent flash memory. Registry is restored from
persistent memory if available or returned to factory default.
WARM BOOT
A warm boot closes all applications, clears the working RAM, but preserves the
file system and registry. If an application "hangs" initiate a warm boot to
terminate the application.
To perform a warm boot, press these keys simultaneously for 5 seconds:
“+”&“-“
COLD BOOT
A cold boot is a complete reset of the Joya™ in which all applications are
forcibly closed and RAM is completely cleared. Registry is restored from
persistent memory if a saved copy is available (see -) and RAM file system
completely erased. You will lose any applications and data (registry too) which
are not stored in persistent flash memory.
A cold boot is necessary when the Windows CE operating system locks up and
the warm boot command does not work.
To perform a cold boot, lightly press with a metallic clip inside the circle hole on
the back.
REGISTRY
Flash Disk
(Backup Folder)
RAM File
System
Warm
Boot
Preserved
Preserved
Cold Boot
Preserved
Reinitialized (factory default)
Restored from flash (if available)
Preserved
Before performing a reset, it is recommended to:
CAUTION
execute a system backup to keep your more important
files and applications persistent. See par. 3.7;
save the registry to non-volatile memory to guarantee
the persistence of the Windows configuration. See
par. -.
27
DATALOGIC JOYA™
3.4
3.4.1
STATUS INDICATORS
Taskbar
The Taskbar provides information about the time, the battery level, the
keyboard function, and the decoding status.
ICONS
DESCRIPTION
Time and Battery
Icons
It displays the time.
They are representative of five different icons indicating
the battery level. The icon is partially green when the
power left is >20% and partially red colored when the
power left is <20%.
It indicates that the battery is charging.
Keyboard Status
Icons
It indicates that the blue FUNC key has been pressed
and is going to affect the next key press.
It indicates that the yellow FUNC key has been pressed
and is going to affect the next key press.
It indicates that the ALPHA key has enabled the
selection of the characters printed in orange.
It indicates the NUMERIC key selection, the ALPHA
key has not been pressed.
It indicates that the ALPHA key has enabled the
selection of the characters printed in orange and the
Capslock is active.
It indicates that the keyboard is locked.
Decoding Status
Icons
It indicates that the decoder is active (green), not active
(grey).
28
USE AND FUNCTIONING
3.5
DATA CAPTURE CONFIGURATION
Confidential
29
DATALOGIC JOYA™
Figure 2
WINDOWS CONNECTIONS
To connect the Datalogic Joya™ to another device (i.e. Host PC) from
Windows, several programs are available.
3.6.1
Microsoft® ActiveSync®
Microsoft® ActiveSync® gives you the possibility to connect your desktop
computer to your Datalogic Joya™ and synchronize the information on them.
Synchronization compares the data on the Datalogic Joya™ with that on the
desktop computer and updates both computers with the most recent
information.
With ActiveSync®, it is possible to:
- Back up and restore Datalogic Joya™ data.
- Copy files between Datalogic Joya™ and desktop computer.
- Synchronize files by selecting a synchronization mode.
You can establish an ActiveSync® connection to your Datalogic Joya™ through
the following electrical interfaces:
USB directly
Bluetooth
 (see par. 3.6.2)
It is possible to constantly synchronize while connected to a desktop computer
or, alternatively, synchronization can be performed only when the synchronize
command is chosen. You can select which information types are synchronized
and control how much data is synchronized.
By default, ActiveSync® does not automatically synchronize
all types of information. Use ActiveSync® options to turn
synchronization on and off for specific information types.
NOTE
For example:
Synchronize Microsoft Word and Microsoft Excel files between the Datalogic
Joya™ and the desktop computer. The files will automatically be converted to
the correct format.
Visit the following Microsoft Web site for the latest in updates
and technical information:
http://www.microsoft.com/windowsmobile/activesync/default.mspx
NOTE
30
USE AND FUNCTIONING
31
DATALOGIC JOYA™
ActiveSync® Remote
NOTE
32
Microsoft® ActiveSync® Remote is no longer supported in
Windows CE. For backward compatibility you can
download it from the Internet. We suggest enabling the FTP
Server and connecting to an FTP Client. See par. 1.1.1.
USE AND FUNCTIONING
3.6.2
Bluetooth® Manager Device Setup
In order to enable a Bluetooth device for communication with the Datalogic
Joya™ you must perform the discovery procedure and enable the device as
follows:
1.
Place the Bluetooth device within the range of the Datalogic Joya™ (10
meters).
2.
From the “Control Panel” main window double tap on the “Bluetooth”
applet to open the Bluetooth® Manager Device window:
3.
Tap on the “Me” button to enter the related window; then, tap on the “ON”
button to activate the Bluetooth module. The module activation may be
also performed by using the WIRELESS COMMUNICATION applet as
described in par. 0.
By tapping on the “HW Details” and “SW Details” buttons, information
about the mobile computer Bluetooth hardware and software will be
displayed, while the “Enable Encryption” button starts encryption of the
Bluetooth communication data. If tapping on the “Close” button the
Bluetooth Manager Device window will be closed.
33
3
4.
DATALOGIC JOYA™
Tap on the “Discovery” button to enter the related window; then, tap on the
“Scan” button to run the Discovery procedure:
Once the Discovery procedure has been completed, select the desired
Bluetooth device from the list. It is also possible to digit (12 hexadecimal
digits) the Bluetooth address of the desired device by tapping on the
“Add” button. The “Clear” button deletes all discovered devices from the
list.
5.
Once the desired Bluetooth device has been selected, tap on the
“Connection Wizard” button to enter the related window where selecting
the connection type to be used for communication with the Bluetooth
device:
The “Serial Port” button starts communication through the Bluetooth
serial port COM 5 (typically used for connection with GPS devices).
The “Printer” button starts communication with a printer through the
Bluetooth serial port COM 5.
The “Kbd Emulation” button allows connection with a barcode reader using
the keyboard emulation.
The “ActiveSync” button starts communication with a PC equipped with a
Bluetooth antenna and the related ActiveSync.
34
USE AND FUNCTIONING
6.
Hide the Bluetooth Manager Device window by tapping on the
icon
available on each window or close it through the “Close” button available
in the “Me” window (see step 3 of this procedure).
35
DATALOGIC JOYA™
3.6.3
FTP Server Setup
Confidential
BACKUP DIRECTORY FILE MANAGEMENT
Confidential
36
USE AND FUNCTIONING
3.8
FIRMWARE UPDATE
Confidential
37
DATALOGIC JOYA™
MAINTENANCE
Battery packs are not initially charged. Therefore the initial
operation to perform is to charge them. See below.
NOTE
CAUTION
4.1
By default, the battery pack is disconnected at the factory
to avoid damage due to excessive draining.
Annual replacement of rechargeable battery pack avoids
possible risks or abnormalities and ensures maximum
performance.
CHARGING THE BATTERY PACK
The battery pack autonomy varies according to factors, such as the frequency
of barcode scanning, RF usage, etc.
The battery icon on the Taskbar indicates when the battery pack is low.
It is also possible to recharge the battery pack by using a Joya Cradle.
Moreover recharging is possible by USB Direct connection with the host
computer, but with longer charging times and in this case it is advised to keep
the mobile computer off.
The battery pack autonomy varies according to many factors,
such as the frequency of barcode scanning, RF usage, battery
life, storage, environmental conditions, etc.
NOTE
CAUTION
If the battery pack is new or has not been recharged for a
long time, it is necessary to perform two or three charging
and discharging cycles (complete use) before it can reach
its maximum charge capability.
The maximum time required to recharge a completely rundown standard battery pack is about 3 hours.
Even if the storage temperature range is wider, In order to
achieve the longest battery life, store the terminal and the
spare batteries between 20 to 30 ºC (68 to 86 ºF).
NOTE
38
The Batteries must be charged at a temperature ranging
from 0° to +45 °C (+32° to +113 °F).
MAINTENANCE
4.2
REPLACING THE BATTERY PACK
To correctly replace the battery pack, proceed as follows.
1.
Unscrew the two screws placed on the back bottom. The battery pack
cover is now released.
39
4
DATALOGIC JOYA™
2.
Remove the cover and then the battery pack, using the proper plastic
strip. Pay attention when disconnecting the connector.
3.
Install the new battery pack, first insert the connector respecting the right
way, then the upper side, finally the bottom side, leaving the plastic strip
available for future replace.
4.
For correct locking, first insert the upper part of the battery cover, then the
lower and rotate the screws to the horizontal position.
40
MAINTENANCE
To install, charge and/or do any other action on the battery,
follow this manual.
WARNING The battery pack may get hot, explode, ignite, and/or cause
serious injury if exposed to abusive conditions.
If the battery pack is replaced with an improper type, there is risk
of explosion.
Do not place the battery pack in or near a fire or heat; do not
place the battery pack in direct sunlight, or use or store the
battery pack inside unventilated areas in hot weather; do not
place the battery pack in microwave ovens, dryer, high pressure
containers, on induction cookware or similar device. Doing so
may cause the battery pack to generate heat, explode or ignite.
Using the battery pack in this manner may also result in a loss of
performance and a shortened life expectancy.
Use only a Datalogic Mobile approved power supply. The use of
an alternative power supply will void the product warranty, may
cause product damage and may cause heat, explode or ignite.
The area in which the units are charged should be clear of
debris and combustible materials or chemicals.
Do not use the battery pack of this terminal for power devices
different from this mobile computer.
Immediately discontinue use of the battery pack if, while using,
charging or storing the battery pack, the battery pack emits an
unusual smell, feels hot, changes colour or shape, or appears
abnormal in any other way.
Do not short-circuit the battery pack contacts connecting the
positive terminal and negative terminal. This might happen, for
example, when you carry a spare battery pack in your pocket or
purse; accidental short–circuiting can occur when a metallic
object such as a coin, clip, or pen causes direct connection of
the contacts of the battery pack (these look like metal strips on
the battery pack). Short–circuiting the terminals may damage the
battery pack or the connecting object.
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer,
step on it or otherwise subject it to strong impacts or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the
battery pack. The battery pack contains safety and protection
devices, which, if damaged, may cause the battery pack to
generate heat, explode or ignite.
41
DATALOGIC JOYA™
In case of leakage of liquid from the battery, avoid contact with
liquid the skin or eyes. If the contact occurs, immediately wash
the affected area with water and consult a doctor.
WARNING
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the
battery is dropped, especially on a hard surface, you should take
it to the nearest Authorised Repair Centre for inspection before
continuing to use it.
Do not replace the battery pack when the device is turned on.
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
Collect and recycle waste batteries separately from the device in
comply with European Directive 2006/66/EC, 2002/95/EC,
2002/96/EC and subsequent modifications, US and China
regulatory and others laws and regulations about environment.
NOTE
In order to guarantee an adequate operating autonomy,
when replacing the battery pack the mobile computer
checks the battery energy level. If the battery is not
sufficiently charged, Datalogic Joya™ does not turn on.
In this case, either substitute the battery pack with a
charged one (sufficiently charged) or insert Datalogic
Joya™ into a powered cradle or plug it into the direct power
supply.
To achieve the best battery life, turn off the radios not in
use.
NOTE
4.3 CLEANING THE MOBILE COMPUTER
Periodically clean the Datalogic Joya™ with a slightly dampened cloth.
42
JOYA CRADLE DISPENSER
TM
JOYA
5.1
CRADLE DISPENSER
INTRODUCTION
TM
Joya
Cradle Dispenser has the following responsibilities:
to recognize the insertion and extraction of the Joya
to control the blocking device
to signal status using the LEDs
to supply power to the Joya for battery recharging
Joya Cradle Dispenser has three Joya slots, each equipped with its own
control unit, an electromechanical system for blocking/releasing the
terminal, notification light, battery power and recharging circuits.
Its special structure makes it possible to design any type of dispenser (wallmounted or island) easily, allowing twice the number of terminals to be installed
per vertical square meter with respect to the competing systems.
5.2
ACCESSORIES
91ACC1000 Power Supply 12V 300W
91ACC0730 Power Junction Cable I90x/3 Cradle (8 pcs.)
91ACC0650 Term. Unlock Magnets (5 pcs.)
43
DATALOGIC JOYA™
5.3
INSTALLATION REQUIREMENTS
Confidential
5.4
BASE UNIT CONSTRUCTION DETAILS
Confidential
5.4.1
TM
Joya
Cradle Dispenser Supports
Confidential
5.4.3
Internal Cabinet Space and Openings
Confidential.
5.4.4
Anchoring and Maintenance Issues
5.4.5
Power Supply Positioning and Cooling
Confidential
Confidential
5.4.6
AC Power Cabling
Confidential
5.4.7
Cable to Power Supply Connection
Confidential
5.4.8
Safety Precautions
Joya Cradle Dispenser Cabinet, the relative electrical wiring and connection to
the AC power line must be made according to the Safety Normatives currently
in force.
The following paragraphs contain some particularly important considerations to
keep in mind.
•
Cradle Dispenser Operating Temperature
Joya Cradle Dispensers are designed and built to operate within the following
environmental conditions:
Operating Temperature Range:
44
10 to 30 °C
JOYA CRADLE DISPENSER
Storage Temperature Range:
-20 to 60 °C
Humidity:
90% non condensing
•
Cabinet
The cabinet must not have any exposed sharp edges, which could represent a
danger to customers.
The requirements for air passages to cool both the JoyaCradle Dispensers and
the power supplies must be adhered to in order to avoid overheating problems
for the components inside the cabinet.
All components having dangerous voltage levels must be protected from
unauthorized access. Only qualified personnel should be authorized access for
maintenance purposes.
In particular, the opening at the top of the cabinet must be closed with a grill or
mesh that prevents access from the outside to the power supplies below. In
addition, the plastic protection covers must be mounted over the power supply
terminals to avoid accidental contact by maintenance personnel when the
cabinet is open.
•
Wiring
The wires used for cabling must have flame retardant insulation.
The cables must be affixed to the cabinet avoiding types of cable clamps that
use screws or have moving parts that press directly upon the cable itself. Cable
clamps must also be applied close to the wires coming from the power supplies
so that they won't be accidentally pulled out of the power supply terminals to
which they are connected.
Avoid running cables with sharp bends or that rest on sharp edges which can
damage them over time and in the long run pose a danger inside the cabinet.
After making all the wiring connections, if some connections have wire exposed
without insulation, they must be insulated.
5.4.9
Connection to AC Line Voltage
If connection to the AC power line is made with a plug at the end of the cable,
The outlet to which it is inserted must be close by and easily accessible. The
outlet must also be rated for the maximum power consumption, which can be
considered equal to the nominal power of the connected power supplies.
If the Terminal Distributor is connected in a fixed electrical plant, a circuit
breaker must be provided in order to completely disconnect the AC line voltage
form the Cradle Dispenser cabinet. This circuit breaker must be positioned
close to the cabinet and be easily accessible. It must also be rated for the
maximum power consumption and must meet the Safety Normatives currently
in force.
45
DATALOGIC JOYA™
5.5
TM
JOYA
CRADLE DISPENSER FIRMWARE
Joya Cradle Dispenser is provided with a full operational Firmware, therefore it
doesn’t require any kind of software devoloping activitiy Instead, the behaviour
of the Joya Cradle Dispenser could be controlled at high level using the Joya.
In SDK Tools is furnished APC.exe program, to upgrade Joya Cradle Dispenser
firmware release.
5.5.1
APC installation
5.5.2
Starting program
confidential
confidential
46
JOYA CRADLE DISPENSER
5.5.3
Reading firmware version
confidential
Cradle locks terminal in the slot, the terminal top flashes three times. At the
end approach a magnet to the sensitive area to unlock and extract the terminal.
If user does not insert Joya into a slot, a timeout message is displayed asking
to remake the operation.
In case of errors a suitable message is displayed.
47
DATALOGIC JOYA™
5.5.4
Firmware update procedure
Confidential
5.6
TM
JOYA
–
CONNECTION
JOYA
TM
CRADLE
DISPENSER
Joya Cradle Dispenser is equipped with an electrical-serial connection, used to
exhange command and response with Joya. The communications between the
terminal inserted into the slot and the slot itself, are performed by means of a
special “RPC like commad-response” protocol.
48
JOYA CRADLE DISPENSER
5.7
CONFIGURATION
Confidential
5.8
USE AND FUNCTIONING
Insert a Joya inside a slot, Joya Cradle Dispenser will lock the Joya, when
electrical connectors are contacted.
To unlock Joya, approach a magnet to the sensitive area and extract the Joya.
All other commands could be developed by devolopers using Joya SDK.
49
DATALOGIC JOYA™
6.1
JOYA ATM/JOYA+ ATM TECHNICAL FEATURES
TECHNICAL DATA
Datalogic Joya ATM/Joya+ A Common Features
Confidential
50
TEST CODES
TEST CODES
High Density Codes
51
DATALOGIC JOYA™
Medium Density Codes
Low Density Codes
52
GLOSSARY
Access Point
A device that provides transparent access between Ethernet wired networks
and IEEE 802.11 interoperable radio-equipped mobile units. Hand-held mobile
computers, PDAs or other devices equipped with radio cards, communicate
with wired networks using Access Points (AP). The mobile unit (mobile
computer) may roam among the APs in the same subnet while maintaining a
continuous, seamless connection to the wired network.
Barcode
A pattern of variable-width bars and spaces which represents numeric or
alphanumeric data in binary form. The general format of a barcode symbol
consists of a leading margin, start character, data or message character, check
character (if any), stop character, and trailing margin. Within this framework,
each recognizable symbology uses its own unique format.
Baud Rate
A measure for data transmission speed.
Bit
Binary digit. One bit is the basic unit of binary information. Generally, eight
consecutive bits compose one byte of data. The pattern of 0 and 1 values
within the byte determines its meaning.
Bluetooth®
A standard radio technology using a proprietary protocol. The onboard
Bluetooth module in the mobile computer is compatible with the 1.1 protocol.
Byte
On an addressable boundary, eight adjacent binary digits (0 and 1) combined in
a pattern to represent a specific character or numeric value. Bits are numbered
from the right, 0 through 7, with bit 0 the low-order bit. One byte in memory can
be used to store one ASCII character.
Decode
To recognize a bar code symbology (e.g., Codabar, Code 128, Code 3 of 9,
UPC/EAN, etc.) and analyze the content of the bar code scanned.
EEPROM
Electrically Erasable Programmable Read-Only Memory. An on-board nonvolatile memory chip.
Flash Disk
Non-volatile memory for storing application and configuration files.
53
Host
A computer that serves other mobile computers in a network, providing
services such as network control, database access, special programs,
supervisory programs, or programming languages.
Liquid Crystal Display (LCD)
A display that uses liquid crystal sealed between two glass plates. The crystals
are excited by precise electrical charges, causing them to reflect light outside
according to their bias. They use little electricity and react relatively quickly.
They require external light to reflect their information to the user.
Light Emitting Diode (LED)
A low power electronic light source commonly used as an indicator light. It uses
less power than an incandescent light bulb but more than a Liquid Crystal
Display (LCD).
RAM
Random Access Memory. Data in RAM can be accessed in random order, and
quickly written and read.
RF
Radio Frequency.
RTC
Real Time Clock.
54
INDEX
Accessories; 2
ActiveSync® Remote; 31
Backup Directory File
Management; 36
Bluetooth® Manager Device
Setup; 32
Charging the Batteries; 40
Cleaning the Mobile Computer; 44
Connections; 3
Control Panel; 18
Conventions; vii
Data Capture; 9
Laser Data Capture; 9
Data Capture Configuration; 13
Datalogic Joyar™ Description; 1
Default Settings; 16
Description of the Keys; 10
End User License Agreement; v
Files Admin; 20
Firmware Update; 37
FTP Server Setup; 35
General View; xix
Glossary; 64
JoyaTM cradle dispenser; 45
Laser Safety; ix
Maintenance; 40
Microsoft® ActiveSync®; 30
Model Description; 1
Package Contents; 2
Patents; xvii
Radio Compliance; xiv
Reader Parameters; 15
Reference Documentation; vii
References; vii
Registry; 18
Replacing the Batteries; 41
Resetting the Joya™; 11
Safe Setup; 20
Safety Regulations; viii
Save Session; 20
Scan Parameters; 15
Startup; 7
Status Indicators; 12
Stylus Calibration; 28
Summit Radio Card; 23
Taskbar; 12
Technical Features; 59
Test Codes; 61
USB Connection; 3
Using the Stylus; 8
WEEE Compliance; xvii
Windows Connections; 30
Wireless Communications; 22
WLAN Connection; 4
WPAN Connections; 6
55
Declarations
They will be added in the final releases


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 63
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2011:08:01 16:13:58
Modify Date                     : 2011:08:01 16:13:58
Title                           : Microsoft Word - 110801_Joya R2U - User's Manual.doc
Creator                         : PScript5.dll Version 5.2.2
Author                          : dvaccaneo

EXIF Metadata provided by EXIF.tools