Datalogic S r l JX2WB JOYA X2 Plus Mobile Computer User Manual II

Download:
Mirror Download [FCC.gov]
Document ID	2438062
Application ID	Nam5i0hkiI9sskoXHszbvA==
Document Description	user manual II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	373.38kB (4667265 bits)
Date Submitted	2014-11-07 00:00:00
Date Available	2015-04-15 00:00:00
Creation Date	2014-11-07 07:32:02
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2014-11-07 07:32:02
Document Title	Microsoft Word - REV3_Joya X2 R2U - User's ManuaL 20141106_REGULATORY.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	dvaccaneo

Acknowledge the license request
Wait for the installation end.
Select Finish.
38
DATALOGIC JOYA™ X2
USE AND FUNCTIONING
Select the DLdcu package
Click on Configure
Select JOYA Configuration then click on the Launch button
DLdcu application will start.
39
DATALOGIC JOYA™ X2
From the File menu select Clone from file, browse up to the previously created
JOYAa.cfg file (see Datalogic Configuration Utility chapter). Close the
application.
Confirm the pop-up request by clicking on the Yes button.
This procedure is required to create a JOYA™ X2 profile in the DLdcu.AVA
package. The existing JOYA profile refers to an incompatible device.
3.5
AVALANCHE PACKAGE BUILDER
3.5.1
Wavelink software package
A software package is a collection of application files that reside on a mobile
device. This includes any support utilities used to configure or manage the
application from the Avalanche Console. A software package includes the
following components
•
•
•
Primary application files. These files include application,
configuration, and support software intended to run on a JOYA™ X2
device.
Plug-in management tools. These include configuration utilities that
allow Management Console operators to easily configure and
manage the software package.
Package control file. This file contains a master description of the
package, including the package title, revision code, “selection criteria”
that determines which device types can receive the package, and
other information. The selection criteria can encompass many mobile
device characteristics, not only JOYA™ X2 including mobile device
models, physical characteristics, IP and/or MAC addresses, etc.
Additionally, Version 3 packages may contain the following components:
40
USE AND FUNCTIONING
•
•
•
•
Retrievable Files. These are files you want to retrieve from the
JOYA™ X2 and copy to the Avalanche Agent. Retrievable files are
supported in the 3x Enabler.
Post Install File. This feature allows you to create script files using
the Package Builder.
Uninstall Command. This is an executable that may be added to
perform specific uninstall instructions, such as the removal of registry
settings.
Custom EULA. This feature allows you to include a customer user
license agreement that must be made available as an HTMLformatted License.text file.
Software packages are divided into the following categories:
•
•
•
•
Control. An internally used package specific to the Avalanche
Console. A network profile is an example of a control package.
Application. These packages install an application which can be run
from the Application Menu screen on the mobile device. An example
of an application package is the Telnet Client.
Support. These packages deliver files and do not add new items to
the Application Menu screen on the mobile device. An example of a
support package is a package that updates an existing file.
Auto Run. These packages automatically run after download but do
not appear in the mobile device’s application list. An Enabler Update
Kit is an example of an auto run package
The Avalanche Package Builder is a specific tool that simplifies the package
creation process. This utility performs several functions:
•
•
•
•
•
•
It gives a visual method for creating and editing software packages. It
simplifies the configuration of the package through a GUI-based
interface.
It creates a file structure to contain all application files, support files,
and plugin configuration files that are required to run and maintain
the application.
GUI interface provides a window into the software package structure,
showing attributes that can be set for each package element.
It automatically generates the package control file.
It places all package files into default or configured locations in the
file structure.
Once the software is packaged, it can easily be transferred or
distributed.
Deep description of this tool is beyond the scope of this document; please refer
to the documentation freely available in the Wavelink website.
3.6
DATALOGIC CONFIGURATION UTILITY
The Datalogic Configuration (DLdcu) is software running on PC that allows
managing the JOYA™ X2 parameters by using the ActiveSync or Windows
Mobile Device Center Connection and a physical USB link.
41
DATALOGIC JOYA™ X2
Full description of this tool is beyond the scope of this document; a detailed
help is embedded in the program. Nevertheless a specific usage description,
involving the Avalanche application, will follow; since it’s not documented
elsewhere.
In order to use the DLdcu, your computer must have the
Microsoft Active Sync or Windows Mobile Device Center
installed.
3.6.1
Create JOYA™ X2 configuration profile
Install the DLdcu software package following the instruction provided by the
DLdcu manual. Connect the JOYA™ X2 to the computer using the MicroUSBUSB cable, wait for the ActiveSync connection then start the DLdcu application.
The solid terminal icon indicates that the terminal is connected.
Click on the icon to get the configuration from device.
42
USE AND FUNCTIONING
Once configuration is loaded it can be edited then reloaded to the device and/or
saved.
Select Save as from the File menu, enter JOYA as filename; program will add
automatically the CFG extension.
Use this file to modify the DLdcu.AVA package as stated above.
3.7
USING THE STYLUS (AVAILABLE ONLY ON JOYA™
X2 PLUS)
The stylus selects items and enters information. The stylus functions like a
mouse.
Double Tap:
Touch the screen twice with the stylus to open items and
select options.
Drag:
Hold the stylus on the screen and drag across the screen to
select text and images. Drag in a list to select multiple items.
Tap-andhold:
Tap and hold the stylus on an item to see a list of actions
available for that item. On the pop-up menu that appears,
tap the action you want to perform.
To recalibrate the touch screen use the Stylus Applet, see Stylus Calibration
paragraph.
Use only original Datalogic styluses supplied with the product
itself.
CAUTION
In
harsh
applications,
use
of
screen
protectors
should be taken into consideration, in order to extend the
touch screen operating life.
To prevent damage to the screen, do not use sharp devices or
any device other than the Datalogic ADC-provided stylus.
Do not apply not necessary high pressures on the screen.
For applications where an intensive use of the touch screen is
foreseen, please consider that touch screen components are
subject to progressive wear.
3.8
DATA CAPTURE
43
DATALOGIC JOYA™ X2
To capture data first of all select the Decoding icon on the Control Panel and
open the applet.
To configure and enable data capture parameters refer to par. 3.11.
3.8.1
Imager Data Capture
The device captures a picture of the entire bar code. The omnidirectional
scanning does not require that the operator orient the bar code to align with the
scan pattern. To read a 1D or 2D code, simply point the JOYA™ X2 onto the
code and press the “Up” key. The JOYA™ X2 uses an intelligent aiming
system pattern, indicating the field of view, which should be positioned over the
code:
44
USE AND FUNCTIONING
45
3
DATALOGIC JOYA™ X2
The field of view changes its size as you move the reader closer or farther
away from the code. The field of view indicated by the aiming system pattern
will be smaller when the device is closer to the code and larger when it is
farther from
the code. Symbologies with smaller bars or elements (mil size) should be read
closer to the unit. Symbologies with larger bars or elements (mil size) should be
read farther from the unit. (See par. 5.1 for further details).
If the scan has taken place correctly:
−
The Good Read LED glows steadily Green for a configurable time;
−
If enabled, the Good Read Beep plays;
−
If enabled, the GreenSpot projects a green spot onto the bar code image
Pop-up windows will report the data and the symbology of the scanned barcode
(see: Configure/Decoding Options paragraph).
46
USE AND FUNCTIONING
3.9
DESCRIPTION OF THE KEYS
The Datalogic JOYA™ X2 provides a 6-key keyboard. The following image
shows this keyboard.
Main Keys Function
+ ”: it corresponds to ArrowUp Key.
Key “ - ”: it corresponds to ArrowDown Key.
Key “
Key “ Left
Key “ Right
”: it corresponds to F1 (Function1) Key.
”: it corresponds to F2 (Function2) Key.
= ”: it corresponds to ESC Key.
Key “ e ” : it corresponds to ENTER Key.
Key “
47
DATALOGIC JOYA™ X2
3.9.1
Resetting the JOYA™ X2
There are three reset methods for the JOYA™ X2
A “warm boot” terminates an unresponsive application and clears the working
RAM, but preserves both the file system and the registry.
A “cold boot” forces all applications to close and clears working RAM and files
not resident on the persistent flash memory. Registry is restored from
persistent memory if available or returned to factory default.
A “clean boot” restore the JOYA™ X2 to factory default.
WARM BOOT
A warm boot closes all applications, clears the working RAM, but preserves the
file system and registry. If an application "hangs" initiate a warm boot to
terminate the application.
To perform a warm boot, press these keys simultaneously for 5 seconds:
“+”&“-”
COLD BOOT
A cold boot is a complete reset of the JOYA™ X2 in which all applications are
forcibly closed and RAM is completely cleared. Registry is restored from
persistent memory if a saved copy is available (see 3.12.1) and RAM file
system completely erased. You will lose any applications and data (registry too)
which are not stored in persistent flash memory.
A cold boot is necessary when the Windows CE operating system locks up and
the warm boot command does not work.
To perform a cold boot, lightly press with a metallic clip inside the circle hole on
the back.
CLEAN BOOT
A clean boot is a complete restore to factory default and backup folder content
erase of the JOYA™ X2. You will loose any applications and data (registry too).
To perform a clean boot first execute a cold boor while keeping pressed the
keys:
“=”&“-”
A pop-up will ask you to confirm, do it by pressing:
“e”
An acknowledge pop-up and reboot will follow.
48
USE AND FUNCTIONING
Clean boot may require a considerable amount of time,
even a few minutes.
CAUTION
Warm Boot
Cold Boot
Restored from the
latest persistent copy
(from flash)
REGISTRY
Preserved
Flash Disk
(Backup Folder)
Preserved
Preserved
Object Store
(RAM Disk)
Preserved
Reinitialized, some
persistent files could
be restored
(from flash)
Storage Card
(IF PRESENT)
Preserved
Preserved
Clean Boot
Reinitialized
Cleared
Reinitialized
Preserved
Before performing a reset, it is recommended to:
CAUTION
Execute a system backup to keep your more
important files and applications persistent.
Save the registry to non-volatile memory to guarantee
the persistence of the Windows configuration..
49
DATALOGIC JOYA™ X2
3.10 STATUS INDICATORS
3.10.1 Taskbar
The Taskbar provides information about the time, the battery level, the
keyboard function, and the decoding status.
ICONS
DESCRIPTION
Time and Battery
Icons
It displays the time.
They are representative of different icons indicating the
battery level. The icon is partially green when the
power left is >20% and partially red colored when the
power left is <20%.
It indicates that the battery is charging.
Radio Status Icons
It indicates if the radio is connected or not with an
Access Point.
Network Status
Icons
It indicates that the terminal is connected or not
connected to the server
50
USE AND FUNCTIONING
Bluetooth Status Icon
It indicates the Bluetooth status: disabled, enabled
not connected, enabled connected.
Scanner Icon
Give access to the scanner control tools.
3.11 DATA CAPTURE CONFIGURATION
Decoding can be accessed from the Control Panel.
There are two sections in the Decoding control panel, each containing
additional pages. There are seven General Configuration pages and multiple
1D/2D Barcode symbology pages.
3.11.1 Configure
Select the desired configuration from the options shown in the figure below, and
the other Decoding Properties figures on the following pages.
Select General, 1D or 2D Bar Code, then use the menu or tap the left and right
arrow keys to navigate the different pages of the Decoding utility. The menu
options will change to reflect the items most recently selected.
51
3
DATALOGIC JOYA™ X2
NOTIFICATION
From the Decoding menu, tap Configure > General > Notification. Use to set
volume, tone, duration, and number of various types of beeps.
GOOD READ
From the Decoding menu, tap Configure > General > Good Read. Select from
Automatic good read, Enable Green Spot, enable LED and Timeout.
52
USE AND FUNCTIONING
FORMATTING
From the Decoding menu, tap Configure > General > Formatting. Select from
Label Prefix, Suffix and data separator. In the Edit window enter the required
value according to the previous choice.
GENERAL OPTIONS
From the Decoding menu, tap Configure > General > General Options. Select
from Label Programming Enable, Symbology IDs, and Group Separator.
53
3
DATALOGIC JOYA™ X2
DECODING OPTIONS
From the Decoding menu, tap Configure > General > Decoding Options. Use to
customize identification of different barcode symbology.
IMAGER OPTIONS
From the Decoding menu, tap Configure > General > Imager Options. Modify
the Imager related feature accordig to your needs.
54
USE AND FUNCTIONING
KEYBOARD WEDGE
From the Decoding menu, tap Configure > General > Keyboard Wedge. Select
Bar code to enable the wedge mode.
1D BARCODE SYMBOLOGY PAGES
Use the drop-down menus from Configure > 1D Barcode, or tap the left and
right arrow keys to navigate the different pages of the 1D barcode symbology
pages.
55
3
DATALOGIC JOYA™ X2
Each barcode symbology opens to its own page, as shown in the figure below.
Refer to the sample symbology control panels for examples of the types of
fields and options you can modify.
Example: Code 39: Enable, Min/Max Lengths = 2/50, not Enable Checksum,
not Send Checksum, Full ASCII Conversion disabled.
56
USE AND FUNCTIONING
2D BARCODE SYMBOLOGY PAGES
Use the drop-down menus from Configure > 2D Barcode, or tap the left and
right arrow keys to navigate the different pages of the 2D barcode symbology
pages.
Each barcode symbology opens to its own page, as shown in the figure below.
Refer to the sample symbology control panels for examples of the types of
fields and options you can modify.
Example: PDF417: Enabled, Min/Max Lengths = 1/2710.
57
3
DATALOGIC JOYA™ X2
DECODING SETTINGS
Select from the Decoding Properties Settings menu to restore previous
configurations and/or other available default settings. Choose from:
•
Factory Defaults
•
Minimum Settings
•
Maximum Settings
•
Save (New Settings)
•
Revert to Saved Settings
The settings are saved when you tap OK.
58
USE AND FUNCTIONING
DECODED DATA
Clicking on the barcode icon on the taskbar opens the decoded data applet.
Press the “+” key and scan a code,
Data and barcode type will be displayed.
59
3
DATALOGIC JOYA™ X2
3.12 CONTROL PANEL
From the Desktop, double tap on the "My Device" icon and then double tap on
the "Control Panel" icon to open the control panel main window. The Control
Panel can also be launched from Start ->Settings ->Control Panel.
Applet programs are displayed as icons; one icon corresponds to each applet.
3.12.1 Registry
The PERSISTENT REGISTRY applet provides management of Windows CE
6.0 registry.
Select the PERSISTENT REGISTRY applet by double tapping the Persistent
Registry icon.
The Persistent Registry Main window appears. Two functions are available:
PERSIST allows permanently saving the Windows configuration (example:
custom configuration of screen desktop background color, or network
adapter configuration) to non-volatile memory.
CLEAR allows restoring the initial factory default configuration. After
restoring the factory default configuration, you must perform a warm boot.
Saving the registry to non-volatile memory guarantees the persistence of the
Windows configuration in case of battery pack replacement and in case of a
Cold Boot.
60
USE AND FUNCTIONING
3.12.2 Using Summit Radio Card Utility
The JOYA Summit WiFi card provides a useful client utility suitable for radio
configuration and site survey purposes.
3.12.3 Summit Radio Card : Starting client
The client can be started from the Windows CE desktop by clicking the related
icon on the tool bar at the bottom, or selecting the Summit Client Utility icon on
the desktop:
61
3
DATALOGIC JOYA™ X2
3.12.4 Summit Radio Card : Main screen
The following picture shows the screen when Summit Client is started
The Active Profile window displays the current profile and lets user to change it.
The Disable Radio button turns off the radio card; after deactivation the same
button changes to Enable Radio so the radio can be reactivated.
To close the application, press the close button at upper-right corner of window.
62
USE AND FUNCTIONING
3.12.5 Summit Radio Card : Profile screen
Radio card is managed through radio profiles.
User can rename, delete, create and save any changes by the Rename,
Delete, New and Commit buttons.
The name chosen for the profile is also his identifier. Profile is defined by a set
of parameter that user can customize. The following is a simple profile for
testing.
Field
SSID
Client Name
Power Save
Tx Power
Bit Rate
Radio Mode
Auth Type
EAP Type
Encryption
Value
tsunami
Z14P00068 (the JOYA™ X2 S/N)
Fast
Maximum
Auto
BGN rates Only
Open
None
None
Once a new profile is created, remember to enable it from the Main windows.
3.12.6 Summit Radio Card : Status screen
This screen shows the radio status related to the profile currently used.
63
3
DATALOGIC JOYA™ X2
User can read current profile name, client device name, IP address and MAC
address. The Access Point to which the terminal is currently associated t is
specified by name, IP address and MAC address.
User can also read the signal strength (dBm), the transmission power
percentage, the WiFi channel, the rate (Mbps).
64
USE AND FUNCTIONING
3.12.7 Summit Radio Card : Diagnostic screen
This screen allows user to interact with radio card to perform simple and useful
functionalities.
The (Re)connect button disables and re-connects radio card.
The Release/Renew button releases and renews the radio interface IP address.
In order to test the radio link, user can ping the associated access point by
pressing the Start Ping button.
The ping output is displayed on the large text windows
65
3
DATALOGIC JOYA™ X2
The Diagnostic button displays the radio configuration and dumps available
profiles
Site Survey functionality is not available.
3.12.8 Summit Radio Card : Global Settings screen
There are many other parameters used to configure the radio card and they do
not depend on used profile, nevertheless for good working it’s recommended
do not change the default values.
66
USE AND FUNCTIONING
3.13 STYLUS CALIBRATION
You might need to recalibrate the touch screen (i.e. when you attempt to select
one item with the stylus, another item is erroneously selected).
To recalibrate the touch screen, complete the following steps:
1. Select Start > Settings > Control Panel > Stylus to open the Stylus
Properties dialog as shown in Figure 1.
2. Select the Double-Tap tab to adjust the sensitivity, if needed or desired.
3. Select the Calibration tab to open the Calibration application.
4.
5.
6.
7.
Tap Recalibrate to open the Calibration screen shown in Figure 2.
Carefully press and briefly hold stylus on the centre of the target. Repeat
as the target moves around the screen. Press the  key to cancel
the stylus calibration.
Press the  key or tap the screen to accept the new calibration
settings. Press the  key to keep the old settings.
New calibration settings are persistently saved in registry.
67
DATALOGIC JOYA™ X2
3.14 WINDOWS CONNECTIONS
To connect the Datalogic JOYA™ X2 to another device (i.e. Host PC) from
Windows, several programs are available.
3.14.1 Microsoft® ActiveSync®
Microsoft® ActiveSync® gives you the possibility to connect your desktop
computer to your Datalogic JOYA™ X2 and move files and folders back and
forth.
With ActiveSync®, it is possible to:
- Back up and restore Datalogic JOYA™ X2 data.
- Copy files between Datalogic JOYA™ X2 and desktop computer.
You can establish an ActiveSync® connection to your Datalogic JOYA™ X2
through the USB interface.
Visit the following Microsoft Web site for the latest in updates
and technical information:
http://msdn.microsoft.com/en-us/library/ee484709.aspx
NOTE
3.14.2 Microsoft® Windows Mobile Device Center®
Microsoft® Windows Mobile Device Center® works as ActiveSync. It is available
in the Microsoft® Windows Vista® and Windows 7® Windows 8® operating
system.
NOTE
Visit the following Microsoft Web site for the latest in updates
and technical information:
http://technet.microsoft.com/enus/library/cc722321(WS.10).aspx
3.14.3 ActiveSync® Remote
Microsoft® ActiveSync® Remote is no longer supported in
Windows CE. For backward compatibility you can
download it from the Internet. We suggest enabling the FTP
68
USE AND FUNCTIONING
NOTE
Server and connecting to an FTP Client. See par.3.14.5.
3.14.4 Bluetooth® Manager Device Setup
In order to enable a Bluetooth device for communication with the Datalogic
Joya™ you must perform the discovery procedure and enable the device as
follows:
1.
Place the Bluetooth device within the range of the Datalogic Joya™ (10
meters).
2.
From the “Control Panel” main window double tap on the “Bluetooth”
applet to open the Bluetooth® Manager Device window:
3.
Tap on the “Me” button to enter the related window; then, tap on the “ON”
button to activate the Bluetooth module. The module activation may be
also performed by using the WIRELESS COMMUNICATION applet as
described in par. Errore. L'origine riferimento non è stata trovata..
By tapping on the “HW Details” and “SW Details” buttons, information
about the mobile computer Bluetooth hardware and software will be
displayed, while the “Enable Encryption” button starts encryption of the
69

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Modify Date                     : 2014:11:07 07:32:02+01:00
Create Date                     : 2014:11:07 07:32:02+01:00
Metadata Date                   : 2014:11:07 07:32:02+01:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - REV3_Joya X2 R2U - User's ManuaL 20141106_REGULATORY.doc
Creator                         : dvaccaneo
Document ID                     : uuid:a0f7870d-a09f-4659-9cbc-7cba31d38b52
Instance ID                     : uuid:82d90b8d-f899-45c7-9dbf-48bb37898ba3
Producer                        : GPL Ghostscript 8.15
Page Count                      : 32
Author                          : dvaccaneo

EXIF Metadata provided by EXIF.tools