DawnSun Electronic Technology ZhongShan TX001-R1 Remote Control-Transmitter User Manual TX001 R1 R8 TX004 R1 R8 TX00
DawnSun Electronic Technology.Co.,Ltd.ZhongShan Remote Control-Transmitter TX001 R1 R8 TX004 R1 R8 TX00
User Manual
OPERATION INSTRUCTION
1
2
3
Front Back
4
5(Optional)
(Optional)
:,
◎
◎
:.
1.Fan speed control button To control the ceiling fan speed HIGH MEDIUM,LOW.
2.FAN/OFF button: Turn off the fan;
Press and hold for 5 seconds to enter Light Delay Off mode.
3.LIGHT ON/OFF/DIMMER button To control light on,off and dimming
(Optional).
(Optional).
(Optional).
4. Extended Function Switch: 1/0
Extended Function Switch: D/CFL
Extended Function Switch: Learn
5.
6.
Remote Control Functions:
(Optional)
6
TX001-R1~TX001-R8:
Note: Install the 12-volt battery to the remote control.
OPERATION INSTRUCTION
1
2
3
4
5(Optional)
(Optional)
:,
◎
◎
:.
1.Fan speed control button To control the ceiling fan speed HIGH MEDIUM,LOW.
2.FAN/OFF button: Turn off the fan;
Press and hold for 5 seconds to enter Light Delay Off mode.
3.LIGHT ON/OFF/DIMMER button To control light on,off and dimming
(Optional).
(Optional).
(Optional).
4. Extended Function Switch: 1/0
Extended Function Switch: D/CFL
Extended Function Switch: Learn
5.
6.
Remote Control Functions:
(Optional)
6
TX004-R1~TX004-R8:
Note: Install the 12-volt battery to the remote control.
Front Back
1
2
3
4
5(Optional)
(Optional)
(Optional)
6
OPERATION INSTRUCTION
:,
◎
◎
:.
1.Fan speed control button To control the ceiling fan speed HIGH MEDIUM,LOW.
2.FAN/OFF button: Turn off the fan;
Press and hold for 5 seconds to enter Light Delay Off mode.
3.LIGHT ON/OFF/DIMMER button To control light on,off and dimming
(Optional).
(Optional).
(Optional).
4. Extended Function Switch: 1/0
Extended Function Switch: D/CFL
Extended Function Switch: Learn
5.
6.
Remote Control Functions:
TX005-R1~TX005-R8:
Note: Install the 12-volt battery to the remote control.
Front Back
OPERATION INSTRUCTION
●Products shall be subject to any changes without additional notices due
to DawnSun will keep innovation and optimization on the products.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1)This device may not cause harmful interference
This device must accept any interference received including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
.
,(2)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and use in accordance with
the instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1.Reorient or relocate the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4.Consult the dealer or an experienced radio/TV technician for help.
,
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
IC STATEMENT
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.