Dayton HRMHW1G Fabric Heart rate monitor User Manual en man heart2feel2

Dayton Industrial Co., Ltd. Fabric Heart rate monitor en man heart2feel2

User Manual

3_ Remove the cover and replace the battery with the positive side facing up.NOTE: Be careful not to damage or losethe o-ring gasket on the cover.4_ Use a coin to twist the coverback into place.SWITCHING OFF THE SENSORAfter 3 minutes of inactivity, all sensorsautomatically power off to conserve thebattery.For more information about optional accessories, go to www.o-synce.com. Youcan also contact your o-synce dealer topurchase accessories.TECHNICAL FEATURESPhysical size: 65 x 38 x 11 mmWeight: 25 gWater Resistance: 10 mTransmission range:Approximately 3 m (9.8 ft)Battery: User-replaceable CR2032 (3 volts)Battery Life:Approximately 3 years (1 hour per day)HEART2feel free/X SOFT BELTThe chest strap must be positionedaround your chest. when correctlyplaced, it sends heart rate informa-tion to the watch. Located on thewrist, the watch displays the heartrate and provides various extra infor-mation (target zone, intensity of exer-cises) to manage and optimize yourfitness and training. The soft belt willbe connected with to clips at thesensor case. The rubber areas haveto be placed on the skin (see photobelow)USING THE HEART2feel free/X SOFT BELTThe Heart2feel free sensor is using ananalog RF communication, so no needfor any pairing. You can use it like des-cribed in the manual of the matchingproduct (MIXfree & MACRO free)The Heart2feel X sensor has to be pai-red like described in the manual forMIXpro & MACRO X – settings - pairing1_ Connect the soft belt with the sensoron one side. Push one bottom of the heart rate sensor on the strap. 2_ Wet both sensors on the back (rub-ber area) of the heart rate monitor tocreate a strong connection between your chest and the transmitter (for extremely dry skin use some special gel)3_ Wrap the strap around your chest and attach it to the other side of the heart rate monitor.NOTE: The o-synce logo should beright-side up.4_ Bring the o-synce product you want to use within range (3 m) of the heart rate monitor. 5_ follow the instruction in user guide toconnect and pair!OPENCR20323V+NOTE: If or heart rate data does notappear or if you have erratic heart ratedata, you may have to tighten the strapon your chest or warm up for 5–10 mi-nutes. If the problem persists, you mayhave to pair the sensors.Reapply moisture to the sensors. Usewater, saliva, or electrode gel. Clean thesensors. Dirt and sweat residue on thesensor can interfere with heart rate si-gnals.Synthetic fabrics that rub or flap againstthe heart rate monitor can create staticelectricity that interferes with heart ratesignals.NOTE: In cold conditions, wear appro-priate clothing to keep the heart ratemonitor near your body temperature.Accuracy may be degraded by poorsensor contact, electrical interferenceand receiver distance from transmitter.Strong electromagnetic fields and some2.4 GHz wireless sensors can interferewith your heart rate monitor. Sources ofinterference may include very high vol-tage power lines, electric motors, micro-wave ovens, 2.4 GHz cordless phones,and wireless LAN access points. Afteryou move away from the source of inter-ference, your heart rate data should re-turn to normal.NOTE: Stay 10 m away from other ANT sensors while pairing. Bring the o-synce product within range (3 m) ofthe heart rate monitor while pairing. Ifthe problem persists, replace the bat-tery. TO REPLACE THE BATTERY1_ Locate the circular battery cover on the back of the sensor.2_ Use a coin to twist the cover coun-er-clockwise until it is loose enough to remove.HEART2feel
NOTES: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is corrected. -- Consult the dealer or experienced radio / TV technician for help. FCC ID: O4GHRM1G IC: 7666A-HRM1G MADE IN CHINA This device complies with part 15 of the FCC Rules. Op erat i on is s ubje ct to th e f oll ow in g c o ndit io ns : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu