Deere and ISG Electronic Systems JDSTG-PSA01 AccuSpeed Doppler Effect Speed Sensor User Manual Accuspeed Installation Instructions

Phoenix International Corporation AccuSpeed Doppler Effect Speed Sensor Accuspeed Installation Instructions

manual

Accuspeed Installation Instructions:FCC Warning:Changes or modifications not expressly approved by Phoenix International could void the user's authority to operate the equipment.Installation:The Accuspeed ground speed sensor is designed as an OEM ground speed sensor, and is to be mounted from 45 cm to 90 cm verticalheight above the ground and at 35 degrees from horizontal. The sensor is designed to face the rear of the vehicle.When designing a mounting bracket, avoid having metal extend beyond the mounting feet of the sensor anywhere around thecircumference of the radome, which is the integrated antenna for this device.The sensor can be mounted directly onto the tractor without need for rubber mounting feet.Avoid having any moving parts (i.e. tires, treads, 3-point hitch, etc) in the line of sight of the sensor.
AccuSpeedDoppler Effect Speed Sensor PHOENIXINTERNATIONALAccuSpeed Doppler Effect Speed SensorThe Phoenix International AccuSpeed DopplerEffect Speed Sensor uses a concentratedmillimeterwave radar signal and the provenDoppler shift principle to accurately measuretrue ground speed of vehicles that operate inadverse environmental conditions.The AccuSpeed sensor combines in itsruggedized plastic enclosure and a uniqueradar front end design with highly integrateddigital signal processing (DSP) electronics.Output signal and installation details arebackward-compatible with older speed sensorproducts. With its small size and low cost,AccuSpeed meets the requirements of OEMcustomers and retrofit markets.AccuSpeed’s industry-standard outputprovides a continuous and robust true groundspeed signal whenever the vehicle is moving.While this signal is useful for driverinformation displays, it also enables closed-loop control systems, such as variable rateapplication techniques, and intelligent vehicledriveline management. A reliable true groundspeed signal will also support emergingautonomous vehicle concepts.The sensor is typically installed at a height of0.6 m but can be installed up to 1.2 m abovethe ground or above the top of the crop. Thesensor should be mounted facing rearwardand positioned so that it has a clear view ofthe ground.The AccuSpeed sensor has passed the fullspectrum of tests specified in the ASAE EP-455 Standard for electronics on mobileequipment including temperature, vibration,moisture, dust, electrical, and theelectromagnetic compatibility (EMC) tests.The unit also meets the requirements of theR&TTE Directive and is CE compliant.
AccuSpeed Speed Sensor Product SpecificationsVelocity Range 0.19 to 39.8 mphAccuracy < ± 3% 0.19-1.9 mph< ± 1% 1.9-39.8 mphMounting Angle 35° depressed below horizontal,rearward-facing (preferred) orforward-facingMounting Height 0.3 to 1.2 m above the ground orabove the top of the crop, typicalmounting height 0.6 mMountingFasteners To Be DeterminedOverall Dimen. 10.2 cm x 10.2 cm x 9.1 cmWeight 0.45 kgConnector CPC: DELPH*12015024 Pin 1 GroundPin 2 Speed Signal OutputPin 3 +12V DC (nominal 12Vvehicle supply) 15 inches or 0.37meter cable length(European version pictured above with anAMP*206429-1 connector and a cablelength of 57.1”inches or 1.45 meters)Electrical Supply 150 mA @ 12 V DC+9 to 16V DC input voltage rangeOutput Frequency 57.42 Hz/mph (128 pulses/meter)@ 45° mounting angleOther frequencies are available bycustom order.Square WaveOutput Z OH ≈ 1000 ohmsZ OL ≤ 100 ohmsV OH ≈ +V (battery)-1.0VV OL ≤ 1.0 V at 15 mAI out (max.) = 22 mAElectricalProtection Signal to ground & signal topower supply protectionElectrical transient protection perASAE EP-455 StandardStep Response ≤ 200 milliseconds delayStart/Stop Delay ≤ 25 cmMicrowaveFrequency 24.125 GHz (standard)24.300 GHz (UK)Tolerance ± 25 MHzMicrowavePower 100 mW (EIRP)RegulatoryCompliance Environmental• ASAE EP-455: includesstandards for reversepolarity, electrical transients(such as load dump,inductive load switching),chemical corrosion, dust, saltspray, rain, wash,mechanical shock, andvibrationElectro-MagneticCompatibility• CE• CSA• FCCStorageTemperature -40C to +85CSpecifications and design subject to change without notice.PHOENIX INTERNATIONAL CORPORATIONFargo, ND u Springfield, ILPhone: 701-282-9364 u Fax: 701-282-9365 u www.phoeintl.com100005GUPrinted in USA

Navigation menu