Deister Electronic MODEL240 Proximity Reader User Manual
Deister Electronic GmbH Proximity Reader Users Manual
Users Manual
GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Description The GE-Interlogix-CASI Model 240 access control badge reader is an ISO standard compliant, proximity technology badge reader. The Model 240 reader will read ISO-14443 and ISO15693 badges and key tags. The reader’s aesthetically pleasing contemporary design and light gray housing will complement any decor. Features: • • • • • • • • • • • Compatible with Micro/5 2RP and 8RP controllers (not M/5-2SRP) Compatible with all Micro/PX(N)-2000 controllers Sealed electronics, suitable for outdoor installation Tamper switch protected Reads ISO-14443 and ISO-15693 access control badges and tags Reads badge or tag serial number, no memory sector records required User interface: 3-LEDs and beeper Fast field maintenance, field wiring plug Up to 4” read range (badge type and installation conditions dependent) 4-state input supervision of door contact & REX switch: opened, closed, cut, short Reader supervision: continuously monitored by the microcontroller Specifications • • • • • • • • • • • • • • • • • • • • Mount: on single width USA or European style electrical box or directly on wall Material: ASA plastic housing; polyurethane encapsulated electronics Housing dimensions: 3.34 x 4.40 x 0.96 inch: (85 x 112 x 24.2 mm) Temperature range: -13 to 140 °F /-25 to +70 °C Power supply: 8VDC to.30 VDC @ <100 mA Electrical protection: Reverse polarity diode protection on power lines Data Lines: high-speed transient voltage suppressor diodes Protection type: IP 65 (IEC 529). Suitable for outdoor installation Frequency: 13.56 MHz Approvals: FCC,CE-EN 300 330 Read distance: up to 2 inches ISO-14443 or up to 4 inches ISO-15693 Microcontroller firmware versions: Picture Perfect 1.7 or greater recommended Interface: Supervised F/2F Electrical connection: 12 position plug-in strip connector with screw terminals Beeper: controlled by SF2F protocol Red LED: controlled by SF2F protocol Green LED: controlled by SF2F protocol Yellow LED: internal controlled RS-485 for reader firmware maintenance and configuration Casi pn: 430177001 Page 1 of 4 GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 FCC Cautionary Comment Modifications to the Model-240 reader not expressly approved by GE-Interlogix may void the FCC approval. Model 240 Back plate Note: Mounting holes fit a standard US single width electrical box and standard European electrical box hole patterns. Installation Page 2 of 4 GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Installation Considerations 1) Installation of the Model 240 reader on metal The table below shows the expected read range reduction when a Model 240 reader is mounted onto a metal plate or wall. Distance Reading distance No metal plate 100 % 1.78 inch (4.5 cm) use 4 Surface 100% Mount Extension plates 1.06 inch, (2.7 cm) use 3 Surface 85 % Mount Extension plates 0.70 inch (1.8 cm) use 2 Surface 70 % Mount Extension plates 0.35 inch (0.9 cm) use 1 Surface 50 % Mount Extension plate Reader placed on metal wall 10 % 2) Installation of two Model 240 readers side by side Read range is not affected if the center-to-center distance between two readers is equal to or greater than 6-inches (15 cm). If the distance between the two readers is less than 6-inches (15 cm), field interference between the two readers may result in the creation of a dead spot in the badge read field. Attention Two readers may simultaneously read the same badge or tag if the distance between the two readers is less than 12-inches (30 cm), center-to-center. Page 3 of 4 GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 3) Installation of two Model 240 readers back to back For proper operation, readers installed back-to-back must be separated by at least 3.2 inches (8cm). Attention Two readers may simultaneously read the same badge or tag if the distance between the two readers is less than 6-inches (15 cm), back-to-back. When using two readers back-to-back on a wall that will separate the two readers by 6 inches (15 cm) or less, a metal plate (for example aluminium, 4-inches square (10cm x 10cm) must be placed between the readers. To obtain the maximum read range, mount each Model 240 reader onto one or more Surface Mount Extension plates. Note the impact on badge read range performance, as discussed in manual section, “Installation Considerations” (above). Wiring Reader 12-position field wiring plug 10 11 12 Microcontroller Micro control, reader beeper (option) Ground Power, 8VDC to 30VDC Door Contact Reader data Exit Request (REX) Green LED Micro control, red LED (option) RS-485-A, reader firmware maintenance RS-485-B, reader firmware maintenance Future Future Micro/5PX(N) 2RP and 8RP, see Micro/5 manual. DO NOT use the Model 240 reader with M/5-S2RP Micro/PX-2000 Micro/PXN-2000 See micro manual Micro/ReaderJunction Box See manual Reader to Micro wiring distance The maximum reader to micro cable distance is 1,000 feet (305 meters) from the microcontroller using 4-conductor 22AWG (0.6438mm) shielded cable. Access Control system compatibility The Model-240 badge reader will output a 16-digit badge identification (BID) number. As a result, the Model-240 reader is only compatible with Picture Perfect access control systems. The Model240 reader is not compatible with Secure Perfect, Secure Perfect Enterprise Edition, SP, or SPEnterprise Edition access control systems, (12-digit BID number limitation). Picture Perfect A 16-digit BID format must be defined within Picture Perfect. Refer to the Picture Perfect On-line help for assistance. In brief, go to Access / Badge Formats. Enter a suitable badge format description, example: “16-digit BID” and define the format: “%16S” (omit the quote characters). Page 4 of 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 2002:09:17 09:12:50 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2002:09:17 09:12:53+02:00 Page Count : 4EXIF Metadata provided by EXIF.tools