Dell 5HCKT 802.11a/b/g Mini PCI type 3B Card User Manual

Dell Inc. 802.11a/b/g Mini PCI type 3B Card Users Manual

CRN 27331 Q2 Revised user manual

Back to Contents Regulatory Information: Intel(R) PRO/Wireless Network Connection User's Guide Intel(R) PRO/Wireless 2200BG Network Connection Intel(R) PRO/Wireless 2915ABG Network Connection Intel(R) PRO/Wireless 2915ABG Network Connection      Information for the User      Regulatory Information Intel(R) PRO/Wireless 2200BG Network Connection      Information for the User      Regulatory Information Intel(R) PRO/Wireless 2915ABG Network Connection The information in this document applies to the following products: Tri-mode wireless LAN adapters (802.11a/802.11b/802.11g ) Intel(R) PRO/Wireless 2915ABG Network Connection (model WM3B2915ABG) Intel(R) PRO/Wireless 2915ABG Network Connection (model WM3A2915ABG) Information for the user Safety Notices The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The Intel(R) PRO/Wireless 2915ABG Network Connection adapter meets the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits. The following safety precautions should be observed: lDo not touch or move antenna while the unit is transmitting or receiving.  lDo not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting.  lDo not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.  lUse in specific environments: ¡The use of wireless devices in hazardous locations is limited by the constraints posed by the safety NOTE:Due to the evolving state of regulations and standards in the wireless LAN field (IEEE 802.11 and similar standards), the information provided herein is subject to change. Intel Corporation assumes no responsibility for errors or omissions in this document. Nor does Intel make any commitment to update the information contained herein.
directors of such environments.  ¡The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).  ¡The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.  lAntenna use: ¡In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20 cm (8 inches) or more from the body of all persons.  ¡High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from the body of all persons. Please contact your professional installer, VAR, or antenna manufacturer for proper installation requirements.  lExplosive Device Proximity Warning (see below)  lAntenna Warning (see below)  lUse on Aircraft Caution (see below)  lOther Wireless Devices (see below)  lPower Supply (Access Point) (see below)  Explosive Device Proximity Warning Warning: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use. Antenna Warnings  Warning: To comply with the FCC and ANSI C95.1 RF exposure limits, it is recommended for the Intel(R) PRO/Wireless 2915ABG Network Connection adapter installed in a desktop or portable computer, that the antenna for this device be installed so as to provide a separation distance of al least 20 cm (8 inches) from all persons and that the antenna must not be co-located or operating in conjunction with any other antenna or radio transmitter. It is recommended that the user limit exposure time if the antenna is positioned closer than 20 cm (8 inches). In case of antennas are installed within 20 cm separation distance from the antennas to the body of user, SAR evaluation has performed to demonstrate RF exposure compliance in the typical lap held operating configuration. Use On Aircraft Caution Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments. Other Wireless Devices Safety Notices for Other Devices in the Wireless Network: Refer to the documentation supplied with wireless Ethernet adapters or other devices in the wireless network. Local Restrictions on 802.11a and 802.11b Radio Usage  Caution: Due to the fact that the frequencies used by 802.11a and 802.11b wireless LAN devices may not yet be harmonized in all countries, 802.11a and 802.11b products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. The device transmit power control (TPC) interface is part of the Intel(R) PROSet/Wireless software. Operational restrictions for Equivalent Isotropic Radiated Power (EIRP) are provided by the system manufacturer. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.  For country-specific information, see the additional compliance information supplied with the product.  Wireless interoperability
The Intel(R) PRO/Wireless 2915ABG Network Connection adapter is designed to be interoperable with other wireless LAN products that are based on direct sequence spread spectrum (DSSS) radio technology and to comply with the following standards: lIEEE Std. 802.1b-1999. Standard on Wireless LAN.  lWireless Fidelity (WiFi) certification, as defined by the WECA (Wireless Ethernet Compatibility Alliance).  The Intel(R) PRO/Wireless 2915ABG Network Connection adapter and your health The Intel(R) PRO/Wireless 2915ABG Network Connection adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The Intel(R) PRO/Wireless 2915ABG Network Connection adapter wireless device operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of the Intel(R) PRO/Wireless 2915ABG Network Connection adapter wireless device may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations include the following: lUsing the Intel(R) PRO/Wireless 2915ABG Network Connection adapter equipment on board airplanes, or  lUsing the Intel(R) PRO/Wireless 2915ABG Network Connection adapter equipment in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful  If you are uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the Intel(R) PRO/Wireless 2915ABG Network Connection adapter wireless device before you turn it on. Regulatory information Information for the OEMs and Integrators:    The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user.  lThis device is intended for OEM integrators only.  lThis device cannot be co-located with any other transmitter.  lPlease refer to the full Grant of Equipment document for other restrictions.  lThis device must be operated and used with a locally approved AP.  Information To Be Supplied to the End User by the OEM or Integrator  The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an Intel(R) PRO/Wireless 2915ABG Network Connection in compliance with local regulations.  The Intel(R) PRO/Wireless 2915ABG Network Connection adapter wireless network device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. For country-specific approvals, see Radio approvals. Intel Corporation is not responsible for any radio or television interference caused by unauthorized modification of the devices included with the Intel(R) PRO/Wireless 2915ABG Network Connection adapter kit, or the substitution or attachment of connecting cables and equipment other than that specified by Intel Corporation. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.
Local Restriction of 802.11a and 802.11b Radio Usage   The following statement on local restrictions must be published as part of the compliance documentation for all 802.11a and 802.11b products.  Caution: Due to the fact that the frequencies used by 802.11a and 802.11b wireless LAN devices may not yet be harmonized in all countries, 802.11a and 802.11b products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from permissible settings and restrictions in the country of use could be an infringement of national law and may be punished as such.  FCC Radio Frequency Interference Requirements  This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device.  lThis device is intended for OEM integrators only.  lThis device cannot be co-located with any other transmitter.    USA—Federal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions: lThis device may not cause harmful interference.  lThis device must accept any interference that may cause undesired operation.  In case of antennas are installed within 20 cm separation distance from the antennas to the body of user, SAR evaluation has performed to demonstrate RF exposure compliance in the typical lap held operating configuration."  Caution: This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. Interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures: lReorient or relocate the receiving antenna.  NOTE:The radiated output power of the Intel(R) PRO/Wireless 2915ABG Network Connection adapter wireless network device is far below the FCC radio frequency exposure limits. Nevertheless, the Intel(R) PRO/Wireless LAN wireless network device should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least  20 cm between you (or any other person in the vicinity) and the antenna that is built into the computer.
lIncrease the distance between the equipment and the receiver.  lConnect the equipment to an outlet on a circuit different from that to which the receiver is connected.  lConsult the dealer or an experienced radio/TV technician for help.  Canada—Industry Canada (IC) This device complies with RSS210 of Industry Canada. This Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210, No 4 (Dec 2000) and No 5 (Nov 2001).  Cet appariel numérique de la classe B est conforme à la norme NMB-003, No. 2, et CNR-210, No 4 (Dec 2000) et No 5 (Nov 2001).. "To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing."  « Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé a l'intérieur et devrait être placé loin des fenêtres afinde fournir un écran de blindage maximal. Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence. »  Europe Frequency Bands 2.400 - 2.4835 GHz (Europe ETSI)  5.15 - 5.35 GHz and 5.47-5.725 GHz (Europe ETSI) 5.15-5.25 can be used outdoors and all other 5 GHz supported must be indoors Low band 5.25 - 5.35 GHz is for indoor use only  5.47 - 5.725 GHz is not allowed in Austria, France and Switzerland   Declaration of Conformity This equipment complies with the essential requirements of the European Union directive 1999/5/EC. NOTE:The Intel(R) PRO/Wireless 2915ABG Network Connection adapter wireless network device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations.English Hereby, Intel(R) Corporation, declares that this Intel(R) PRO/Wireless 2915ABG Network Connection is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Finnish Intel(R) Corporation vakuuttaa täten että Intel(R) PRO/Wireless 2915ABG Network Connection tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Dutch Hierbij verklaart Intel(R) Corporation dat het toestel Intel(R) PRO/Wireless 2915ABG Network Connection in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG Bij deze verklaart Intel(R) Corporation dat deze Intel(R) PRO/Wireless 2915ABG Network Connection voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
  New Member States requirements of Declaration of Conformity French Par la présente Intel(R) Corporation déclare que l'appareil Intel(R) PRO/Wireless 2915ABG Network Connection est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CEPar la présente, Intel(R) Corporation déclare que ce Intel(R) PRO/Wireless 2915ABG Network Connection est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicablesSwedish Härmed intygar Intel(R) Corporation att denna Intel(R) PRO/Wireless 2915ABG Network Connection står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.Danish Undertegnede Intel(R) Corporation erklærer herved, at følgende udstyr Intel(R) PRO/Wireless 2915ABG Network Connection overholder de væ sentlige krav og øvrige relevante krav i direktiv 1999/5/EFGerman Hiermit erklärt Intel(R) Corporation, dass sich dieser/diese/dieses Intel(R) PRO/Wireless 2915ABG Network Connection in Ü bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)Hiermit erklärt Intel(R) Corporation die Übereinstimmung des Gerätes Intel(R) PRO/Wireless 2915ABG Network Connection mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)Greek ?? ??? ?????S? Intel(R) Corporation ???O??? ??? Intel(R) PRO/Wireless 2915ABG Network Connection S?????FO????? ???S ??S ??S?O???S ??????S??S ??? ??S ?????S S??????S ????????S ??S ???G??S 1999/5/??Italian Con la presente Intel(R) Corporation dichiara che questo Intel(R) PRO/Wireless 2915ABG Network Connection è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CESpanish Por medio de la presente Intel(R) Corporation declara que el Intel(R) PRO/Wireless 2915ABG Network Connection cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CEPortuguese Intel(R) Corporation declara que este Intel(R) PRO/Wireless 2915ABG Network Connection está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Malti Hawnhekk, Intel(R) Corporation, jiddikjara li dan Intel(R) PRO/Wireless 2915ABG Network Connection jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/ECEstonian Käesolevaga kinnitab Intel(R) Corporation seadme Intel(R) PRO/Wireless 2915ABG Network Connection vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.Hungary Alulírott, Intel(R) Corporation nyilatkozom, hogy a Intel(R) PRO/Wireless 2915ABG Network Connection megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainakSlovak Intel(R) Corporation týmto vyhlasuje, že Intel(R) PRO/Wireless 2915ABG Network Connection splna základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Czech Intel(R) Corporation tímto prohlašuje, že tento Intel(R) PRO/Wireless 2915ABG Network Connection je ve shode se základními požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES."Slovenia Šiuo Intel(R) Corporation deklaruoja, kad šis Intel(R) PRO/Wireless 2915ABG Network Connection atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
France For Metropolitan departments 2.400 - 2.4835 GHz for indoor use  2.400 -2.454 GHz (channels 1 to 7) for outdoor use Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors is:  l10 mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz)  l100 mW for frequencies between 2446.5 MHz and 2483.5 MHz (Note: Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5 MHz)  There are few possibilities for outdoor use: On private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defense, with maximum authorized power of 100 mW in the 2446.5–2483.5 MHz band. Use outdoors on public property is not permitted. In the departments listed below, for the entire 2.4 GHz band: lMaximum authorized power indoors is 100 mW  lMaximum authorized power outdoors is 10 mW  There is partial restriction of the 2.4 GHz band for outdoor/indoor in part of the 2.4 GHz band, according to the OEM Regulatory and Safety Notice Guidelines of CX2 2200BG (see page 12, concerning France). Departments in which the use of the 2400–2483.5 MHz band is permitted with an EIRP of less than 100 mW indoors and less than 10 mW outdoors:   Latvian Ar šo Intel(R) Corporation  deklare, ka Intel(R) PRO/Wireless 2915ABG Network Connection atbilst Direktivas 1999/5/EK butiskajam prasibam un citiem ar to saistitajiem noteikumiemLithuanianIntel(R) Corporation deklaruoja, kad Intel(R) Pro/Wireless 2915ABG Network Connectionatitinka 1999/5/EC Direktyvos esminius reikalavimus ir  kitas nuostatas".PolishNiniejszym, Intel(R) Corporation, deklaruje, ze  Intel(R) PRO/Wireless 2915ABG Network Connection spelnia wymagania zasadnicze oraz stosowne postanowienia zawarte  Dyrektywie 1999/5/EC.01  Ain Orientales 36 Indre 66 Pyrénées02 Aisne 37 Indre et Loire 67 Bas Rhin03 Allier 41 Loir et Cher 68 Haut Rhin05 Hautes Alpes 42 Loire 70 Haute Saône08 Ardennes 45 Loiret 71 Saône et Loire09 Ariège 50 Manche 75 Paris11 Aude 55 Meuse 82 Tarn et Garonne12 Aveyron 58 Nièvre 84 Vaucluse16 Charente 59 Nord 88 Vosges24 Dordogne 60 Oise 89 Yonne25 Doubs 61 Orne 90 Territoire de Belfort
This requirement is likely to change over time, allowing the use your Network Connection card in more areas within France. Please check with ART for the latest information (http://www.telecom.co.fr/) For Guadeloupe, Martinique, St Pierre et Miquelon, Mayotte:  2.400 - 2.4835 GHz for indoor and outdoor use. For Reunion, Guyane: 2.400 - 2.4835 GHz for indoor use.  2.420 - 2.4835 GHz for outdoor use (channels 5 to 13)   Italia A license is required for indoor use. Outdoor use is prohibited.   Japan Frequency Bands 2.400 - 2.497 GHz (Japan) 5.15 to 5.25 (offset Japanese channels) active scan  High Band Frequencies 5.725 to 5.825 active scan   Radio approvals To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacture OEM Regulatory Guidance document. Underwriters Laboratories Inc. (UL) Regulatory Warning For use in (or with) UL Listed personal computers or compatible.   Back to Top Back to Contents Regulatory Information: Intel(R) PRO/Wireless 2200BG Network 26 Drôme 63 Puy du Dôme 94 Val de Marne32 Gers 64 Pyrénées Atlantique    NOTE:Your Intel(R) PRO/Wireless 2915ABG Network Connection adapter transmits less than 100 mW, but more than 10 mW.NOTE:E' necessaria la concessione ministeriale anche per l'uso interno. Verificare con i rivenditori la procedura da seguire. L'uso per installazione in esterni non e' permessa.
Connection  Information for the User Regulatory Information Information for the user Safety Notices The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The Intel(R) PRO/Wireless 2200BG Network Connection meets the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits. The following safety precautions should be observed: lDo not touch or move antenna while the unit is transmitting or receiving.  lDo not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting.  lDo not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.  lUse in specific environments: ¡The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments.  ¡The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).  ¡The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. lExplosive Device Proximity Warning (see below)  lAntenna Warning (see below)  lUse on Aircraft Caution (see below)  lOther Wireless Devices (see below)  lPower Supply (Access Point) (see below) Explosive Device Proximity Warning  Warning: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use. Antenna Warnings  Warning: To comply with the FCC and ANSI C95.1 RF exposure limits, it is recommended for the Intel(R) PRO/Wireless 2200BG Network Connection installed in a desktop or portable computer, that the antenna for this device be installed so as to provide a separation distance of al least 20 cm (8 inches) from all persons and that the antenna must not be co-located or operating in conjunction with any other antenna or radio transmitter. It is recommended that the user limit exposure time if the antenna is positioned closer than 20 cm (8 inches).  Warning: The Intel(R) PRO/Wireless 2200BG Network Connection product is not designed for use with high-gain directional antennas. Use of such antennas with these products is illegal. Use On Aircraft Caution
 Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments. Local Restrictions on 802.11b Radio Usage  Caution: Due to the fact that the frequency used by 802.11b wireless LAN devices may not yet be harmonized in all countries, 802.11b products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from the permissible settings for the country of use is an infringement of national law and may be punished as such. For country-specific information, see the additional compliance information supplied with the product. Wireless interoperability The Intel(R) PRO/Wireless 2200BG Network Connection adapter is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) radio technology and to comply with the following standards: lIEEE Std. 802.11b-1999. Standard on Wireless LAN.  lIEEE Std. 802.11g compliant. Standard on Wireless LAN.  lWireless Fidelity (WiFi(R)) certification, as defined by the WECA (Wireless Ethernet Compatibility Alliance).  The Intel(R) PRO/Wireless LAN 2200 3A Mini PCI adapter and your health The Intel(R) PRO/Wireless 2200BG Network Connection adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The Intel(R) PRO/Wireless 2200BG Network Connection adapter wireless device operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of the Intel(R) PRO/Wireless 2200BG Network Connection adapter wireless device may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations include the following: lUsing the Intel(R) PRO/Wireless 2200BG Network Connection adapter equipment on board airplanes, or  lUsing the Intel(R) PRO/Wireless 2200BG Network Connection adapter equipment in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If you are uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the Intel(R) PRO/Wireless 2200BG Network Connection adapter wireless device before you turn it on. Regulatory information The Intel(R) PRO/Wireless 2200BG Network Connection adapter wireless network device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. For country-specific approvals, see Radio approvals. Dell Inc. is not responsible for any radio or television interference caused by unauthorized modification of the devices included with the Intel(R) PRO/Wireless 2200BG Network Connection adapter kit, or the substitution or attachment of connecting cables and equipment other than that specified by Dell Inc. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Dell inc. and its authorized resellers or distributors are not liable for any
damage or violation of government regulations that may arise from the user failing to comply with these guidelines. USA—Federal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions: lThis device may not cause harmful interference.  lThis device must accept any interference that may cause undesired operation. Interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures: lReorient or relocate the receiving antenna.  lIncrease the distance between the equipment and the receiver.  lConnect the equipment to an outlet on a circuit different from that to which the receiver is connected.  lConsult the dealer or an experienced radio/TV technician for help. U.S. Frequency Bands 2.400 - 2.473 GHz  Canada—Industry Canada (IC) This Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210, Issue 4 (Dec. 2000).  Cet appariel numérique de la classe B est conforme à la norme NMB-003, No. 2, et CNR-210, No 4 (Dec 2000). "To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its trasmit antenna) that is installed outdoors is subject to licensing."  « Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé a l'intérieur et devrait être placé loin des fenêtres afinde fournir un écran de blindage maximal. Si le matériel (ou son NOTE:Your Intel(R) PRO/Wireless 2200BG Network Connection adapter transmits less than 100 mW, but more than 10 mW.NOTE:The radiated output power of the Intel(R) PRO/Wireless 2200BG Network Connection adapter wireless network device is far below the FCC radio frequency exposure limits. Nevertheless, the Intel(R) PRO/Wireless 2200BG Network Connection device should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20 cm between you (or any other person in the vicinity) and the antenna that is built into the computer. To determine the location of the antenna within your computer, check the information posted on the general Dell support site at http://www.support.dell.com/.NOTE:The Intel(R) PRO/Wireless 2200BG Network Connection adapter wireless network device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations.
antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence. »  Europe—EU Declaration of Conformity Europe Frequency Bands 2.400 - 2.4835 GHz (Europe ETSI) This equipment complies with the essential requirements of the European Union directive 1999/5/EC. Cet équipement est conforme aux principales exigences essentielles définies dans la Directive européenne RTTE 1999/5/CE. Die Geräte erfüllen die grundlegenden Anforderungen der RTTE-Richtlinie 1999/5/EG. Questa apparecchiatura è conforme ai requisiti essenziali della Direttiva Europea R&TTE 1999/5/CE. Este equipo cumple los requisitos principales de la Directiva 1999/5/CE de la UE, "Equipos de Terminales de Radio y Telecomunicaciones". Este equipamento cumpre os requisitos essenciais da Directiva 1999/5/CE do Parlamento Europeu e do Conselho (Directiva RTT). O exoplismos autos plhroi tis basikes apaits ths koinotikhs odhgias EU R&TTE 1999/5/E. Deze apparatuur voldoet aan de noodzakelijke vereisten van EU-richtlijn betreffende radioapparatuur en telecommunicatie-eindapparatuur 1999/5/EG. Dette udstyr opfylder de Væ sentlige krav i EU's direktiv 1999/5/EC om Radio- og teleterminaludstyr. Dette utstyret er i overensstemmelse med hovedkravene i R&TTE-direktivet (1999/5/EC) fra EU. Utrustningen uppfyller kraven för EU-direktivet 1999/5/EC om ansluten teleutrustning och ömsesidigt erkännande av utrustningens överensstämmelse (R&TTE). Tämä laite vastaa EU:n radio- ja telepäätelaitedirektiivin (EU R&TTE Directive 1999/5/EC) vaatimuksia. France Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors is:  l10 mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz)  l100 mW for frequencies between 2446.5 MHz and 2483.5 MHz (Note:Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5 MHz)  There are few possibilities for outdoor use: On private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defense, with maximum authorized power of 100 mW in the 2446.5–2483.5 MHz band. Use outdoors on public property is not permitted. In the departments listed below, for the entire 2.4 GHz band: lMaximum authorized power indoors is 100 mW  lMaximum authorized power outdoors is 10 mW  Departments in which the use of the 2400–2483.5 MHz band is permitted with an EIRP of less than 100 mW indoors and less than 10 mW outdoors:
This requirement is likely to change over time, allowing the use your wireless LAN card in more areas within France. Please check with ART for the latest information (http://www.telecom.co.fr/) Belgique   Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus d'un espace public, aucun enregistrement n'est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de l'IBPT est requise.  Pour les enregistrements et licences, veuillez contacter l'IBPT. Italia For use in private premises: no restriction outdoor or indoor, 2.400 - 2.4835 Ghz  For use in public premises: no restriction outdoor or indoor, 2.400 - 2.4835 Ghz, but a general authorization has to be requested to the ministry of Post and telecommunications. Japan Frequency Bands 2.400 - 2.497 GHz (Japan) Radio approvals To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed on the radio approval list posted on the general Dell support site at http://www.support.dell.com/. Back to Top Back to Contents 01 Ain Orientales 36 Indre 66 Pyrénées02 Aisne 37 Indre et Loire 67 Bas Rhin03 Allier 41 Loir et Cher 68 Haut Rhin05 Hautes Alpes 42 Loire 70 Haute Saône08 Ardennes 45 Loiret 71 Saône et Loire09 Ariège 50 Manche 75 Paris11 Aude 55 Meuse 82 Tarn et Garonne12 Aveyron 58 Nièvre 84 Vaucluse16 Charente 59 Nord 88 Vosges24 Dordogne 60 Oise 89 Yonne25 Doubs 61 Orne 90 Territoire de Belfort26 Drôme 63 Puy du Dôme 94 Val de Marne32 Gers 64 Pyrénées Atlantique

Navigation menu