Dell APL290B7 Wireless Network Security Appliance User Manual Dell SonicWALL TZ500 TZ500 W Quick Start Guide

Download:
Mirror Download [FCC.gov]
Document ID	2659169
Application ID	/wAVNYSHO64JiJh7vfBG7g==
Document Description	Users Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	81.03kB (1012823 bits)
Date Submitted	2015-06-26 00:00:00
Date Available	2015-07-07 00:00:00
Creation Date	2015-03-02 10:03:53
Producing Software	Acrobat Distiller 10.1.13 (Windows)
Document Lastmod	2015-06-04 18:39:19
Document Title	Dell SonicWALL TZ500 / TZ500 W Quick Start Guide
Document Creator	FrameMaker 10.0.2
Document Author:	Dell Inc

Dell SonicWALL TZ Series
TZ500 / TZ500 W front and
back panels
Check package contents
Verify that your package has the following contents:
• Dell SonicWALL appliance
Wireless (W0) LED
Front Panel
(TZ500 W only) Indicates
802.11 b/g/n/ac security
status
• Antennas (3) (TZ500 W appliance only)
USB / SSD port
Ethernet Port Status (X0-X7)
External USB and SSD hard
drive support
Top - Provides 10/100 Mbps Ethernet port status
Bottom - Provides 1 Gbps Ethernet port status
• Ethernet cable
• Standard power adaptor
Dell SonicWALL™ TZ500 /
TZ500 W
1000
W0
SonicWALL TZ500 W
X0
X3
X4
X5
X6
X7
10/100/act
1000/act
lan
(TZ500 W only) Indicates 802.11
b/g/n/ac activity
For future use
Fast blinking - Initializing
Slow blinking - SafeMode
Antenna Screws (3)
Center Antenna Screw
(TZ500 W only) Provides wireless capabilities
to the Dell SonicWALL appliance
(TZ500 W only) The center antenna screw is only
compatible with the enclosed center antenna
• Connect the power adaptor to the appliance and to
the power cable. Plug the power cable into an
appropriate outlet (100-240 volts AC).
NOTE: The included power cord is approved for use
only in specific countries or regions. Before using a
power cord, verify that it is rated and approved for
use in your location.
120V AC
(U.S.)
• The TZ appliance powers on and the Test LED
blinks during the boot sequence.
power
TZ500 = Regulatory Model Number: APL29-0B6
wan
lan
1000
W0
SonicWALL TZ500 W
TZ500W = Regulatory Model Number: APL29-0B7
• Connect the antennas to the appliance. Note that
the center antenna is labeled and is only
compatible with the center antenna screw.
(TZ500 W appliance only)
• Quick Start Guide
Test LED
Rear Panel
• Standard power cord
Power on
• Serial console cable
wan
Wireless LAN LED
Service LED
Indicates Power Supply status
Quick Start Guide (Beta Version)
X2
on / act
ss
Power LED
X1
security
X0
X1
lan
wan
security
console
X7
X6
X5
X4
X3
X2
X1
ss
X0
X2
X3
X4
X5
X6
X7
10/100/act
1000/act
on / act
Power Supply
Console Port
Access the SonicOS Command
Line Interface (CLI) using a
compatible CLI cable
X2 - X7 Ports
Configurable ports
X1 Port
1000
W0
SonicWALL TZ500 W
Provides power to
the Dell SonicWALL
appliance
X0
X1
lan
wan
X3
X4
X5
X6
X7
1000/act
on / act
ss
X2
10/100/act
security
For WAN access
Reset Button
X0 Port
For LAN access
Press and hold for several
seconds to set the appliance
into Safe Mode
CAUTION: Only use the included power adapter
with this appliance. Do not use a power adapter
that is damaged or from another appliance.
Connect the interfaces
• Connect the WAN interface (X1) to your Internet
connection using a standard Ethernet cable.
• Connect the LAN interface (X0) to your computer
using a standard Ethernet cable.
wan
lan
X1
X0
TIP: Your computer should be using DHCP IP
addressing.
• Click on the link in “To launch the Dell SonicWALL
Setup Wizard, click here.”
• Enter the TZ appliance administrator credentials
to change the password, if you wish. Click Next.
NOTE: The default administrator credentials are
Username: admin Password: password
Configuring Wireless LAN settings
• The automatic WAN IP settings are displayed.
Click Next.
• Select the radio button for the Wireless Guide
wizard.
• Log in to your TZ appliance and click the Wizards
icon.
Internet
• The SonicOS Startup Guide opens.
Run the Setup Wizard
• Navigate to https://192.168.168.168 on your Web
browser.
NOTE: For manual configuration, refer to the latest
SonicOS Administration Guide.
http://192.168.168.168/
http://192.168.168.168/
• The new IP Configuration is displayed. Click Done.
• Click Next and follow the prompts in the Startup
Guide pages that follow.
• Click Next and follow the prompts in the Wireless
Guide wizard.
For more information and complete procedures,
refer to the latest SonicOS Administration Guide.
Dell SonicWALL TZ Series
Register product
• Point your browser to the appliance LAN IP address
(default https://192.168.168.168) and log in using
the administrator credentials.
• Log in using your MySonicWALL account name and
password. If you do not have a MySonicWALL
account, click the Create MySonicWALL account
link to create an account.
• Click Register on the System > Status page under
Security Services.
Get the latest firmware
WARNING: Do not mount the appliance on the
ceiling, it is not designed for secure ceiling
mounting.
• Click Downloads and select TZ500 or TZ500 W
Firmware from the Software Type menu.
For optional wall mounting, you need:
• Click the link for the firmware you want and save
the file to a location on your computer.
• Drill with appropriate size bit
• Click the Browse button to navigate to and select
the firmware you just downloaded.
• Screwdriver
• For mounting on drywall:
• Two #6 pan-head screws, 1 inch long (7mm
diameter head, 25mm long)
• Two wall anchors
• For mounting on solid wood or metal:
• Two #6 pan-head wood or machine screws, 1
inch long (7mm diameter head, 25mm long)
To mount the appliance on the wall:
TIP: Registering the appliance from SonicOS
requires that DNS Server settings are configured on
the WAN (X1) interface.
NOTE: Your appliance must be registered to
download the latest firmware.
Mounting the TZ appliance
• In a Web browser, navigate to
http://www.mysonicwall.com
• On the TZ appliance, navigate to the
System > Settings page. Click the Upload New
Firmware button.
• MySonicWALL directly obtains the necessary
information from the TZ appliance. When finished,
you will see a message that registration has been
completed. Click Continue.
• Click Upload and wait for the upload to complete.
1 Drill two holes 4.5 inches (11.5 cm) apart in the
wall where you want to mount the appliance.
2 If using wall anchors, insert a wall anchor into
each hole.
3 Insert a screw into each wall anchor (into each
hole if not using wall anchors), leaving 3/16 inches
(0.45 cm) of the screws exposed (including screw
head).
4 Position the appliance mounting slots over the
screws and press in and down until the appliance is
securely mounted.
• In the Firmware Management Table, click the
Boot icon for your new firmware.
Safety and regulatory
information
Declaration of conformity
Informationen zur stromversorgung
A Declaration of Conformity in accordance with the directives and standards has A “Declaration of
Conformity” in accordance with the directives and standards has been made and is on file at Dell Products
Europe BV, Limerick, Ireland.
Wenn die Stromversorgung von der Dell-Produktpaket fehlt, wenden Dell den Technischen Support unter
https://support.software.dell.com/manage-service-request.
CE declarations can be found online at www.dell.com.
Mounting the appliance
Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º
F (40º C) is recommended.
Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios,
transmitters, and broadband amplifiers.
The included power cord(s) are approved for use only in specific countries or regions. Before using a power
cord, verify that it is rated and approved for use in your location.
NOTE: Additional regulatory notifications and information for this product can be found online at:
https://support.software.dell.com/
Verwarnung Weitere hinweise zur
montage
Dieses Produkt sollte nur mit einem für den Europäischen Markt genehmigten Netzteil mit dem Logo "I.T.E.
LPS" und einer Ausgangsleistung von12 VDC, mind. 3.0 A, Tma: mind. 40 Grad C, betrieben werden.
©
2015 Dell Inc. ALL RIGHTS RESERVED.
This guide contains proprietary information protected by copyright. The software described in this guide is
furnished under a software license or nondisclosure agreement. This software may be used or copied only
in accordance with the terms of the applicable agreement. No part of this guide may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including photocopying and recording
for any purpose other than the purchaser’s personal use without the written permission of Dell Inc.
The information in this document is provided in connection with Dell products. No license, express or
implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in
connection with the sale of Dell products. EXCEPT AS SET FORTH IN THE TERMS AND CONDITIONS AS
SPECIFIED IN THE LICENSE AGREEMENT FOR THIS PRODUCT, DELL ASSUMES NO LIABILITY WHATSOEVER AND
DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
NON-INFRINGEMENT. IN NO EVENT SHALL DELL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL,
PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF
PROFITS, BUSINESS INTERRUPTION OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE
THIS DOCUMENT, EVEN IF DELL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Dell makes no
representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and product descriptions at any time
without notice. Dell does not make any commitment to update the information contained in this document.
If you have any questions regarding your potential use of this material, contact:
Ensure that no water or excessive moisture can enter the unit.
Wählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht ausgesetzt ist und sich nicht in der
Nähe von Wärmequellen befindet. Die Umgebungstemperatur darf nicht mehr als 40 °C betragen.
Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1
inch (25.44mm) clearance is recommended.
Führen Sie die Kabel nicht entlang von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern
oder Breitbandverstärkern.
Consideration must be given to the connection of the equipment to the supply circuit. Appropriate
consideration of equipment nameplate ratings must be used when addressing this concern. Do not overload
the circuit.
Das im Lieferumfang enthaltene bzw. die im Lieferumfang enthaltenen Netzkabel sind nur für die
Verwendung in bestimmten Ländern und Regionen zugelassen. Überprüfen Sie bitte vor der Verwendung eins
Netzkabels, ob es für die Verwendung in Ihrem Land oder Ihrer Region zugelassen ist und den geforderten
Normen entspricht.
Refer to our website (software.dell.com) for regional and international office information.
Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit geschützt ist.
http://software.dell.com/legal/patents.aspx.
Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die Lüftungsschlitze an der Seite
des Gehäuses frei sind. Hier ist ein Belüftungsabstand von mindestens 26 mm einzuhalten.
Trademarks
This equipment is not intended for use at workplaces with visual display units, in accordance with §2 of the
German ordinance for workplaces with visual display units. To avoid incommoding reflections at visual
display workplaces this device must not be placed in the direct field of view.
Lithium battery warning
The Lithium Battery used in the Dell SonicWALL security appliance may not be replaced by the user. Return
the Dell SonicWALL security appliance to a Dell SonicWALL-authorized service center for replacement with
the same or equivalent type recommended by the manufacturer. If, for any reason, the battery or Dell
SonicWALL security appliance must be disposed of, do so following the battery manufacturer's instructions.
Cable connections
All Ethernet and RS232 (Console) cables are designed for intra-building connection to other equipment. Do
not connect these ports directly to communication wiring or other wiring that exits the building where the
Dell SonicWALL appliance is located.
Power supply information
If the power supply is missing from your Dell SonicWALL product package, please contact Dell SonicWALL
Technical Support at https://support.software.dell.com/manage-service-request/ for a replacement. This
product should only be used with a UL listed power supply marked “I.T.E. LPS” with an output rated 12V DC,
minimum 3.0 A, Tma: minimum 40 degree C.
Prüfen Sie den Anschluss des Geräts an die Stromversorgung, damit der Überstromschutz sowie die
elektrische Leitung nicht von einer eventuellen Ãœberlastung der Stromversorgung beeinflusst werden.
Prüfen Sie dabei sorgfältig die Angaben auf dem Aufkleber des Geräts. Überlasten Sie nicht den
Stromkreis.
Dieses Gerät ist nicht zur Verwendung an Arbeitsplätzen mit visuellen Anzeigegeräten gemäß § 2 der
deutschen Verordnung für Arbeitsplätze mit visuellen Anzeigegeräten vorgesehen.Um störende Reflexionen
am Bildshirmarbeitsplatz zu vermeiden, darf dieses Produkt nicht im unmittelbaren Gesichtsfeld platziert
verden.
Verwarnung hinweis zur lithiumbatterie
Die in der Internet Security Appliance von Dell verwendete Lithiumbatterie darf nicht vom Benutzer
ausgetauscht werden. Zum Austauschen der Batterie muss die Dell in ein von Dell autorisiertes ServiceCenter gebracht werden. Dort wird die Batterie durch denselben oder entsprechenden, vom Hersteller
empfohlenen Batterietyp ersetzt. Beachten Sie bei einer Entsorgung der Batterie oder der Dell Internet
Security Appliance die diesbezüglichen Anweisungen des Herstellers.
Verwarnung kabelverbindungen
Alle Ethernet- und RS232-C-Kabel eignen sich für die Verbindung von Geräten in Innenräumen. Schließen Sie
an die Anschlüsse der Dell keine Kabel an, die aus dem Gebäude herausgeführt werden, in dem sich das
Gerät befindet.
Dell Inc.
Attn: LEGAL Dept
5 Polaris Way
Aliso Viejo, CA 92656
Patents
This product is protected by U.S. Patents. For more information, go to
Dell, the Dell logo, and SonicWALL are trademarks of Dell Inc. Other trademarks and trade names may be
used in this document to refer to either the entities claiming the marks and names or their products. Dell
disclaims any proprietary interest in the marks and names of others.
TZ500 / TZ500 W Quick Start Guide
Updated - May 2015
232-00xxxx-50 Rev A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Dell Inc
Create Date                     : 2015:03:02 10:03:53Z
Keywords                        : APL26-0AE
Modify Date                     : 2015:06:04 18:39:19-06:00
Language                        : en
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 10.1.13 (Windows)
Format                          : application/pdf
Title                           : Dell SonicWALL TZ500 / TZ500 W Quick Start Guide
Creator                         : Dell Inc
Description                     : Quick Start Guide
Subject                         : APL26-0AE
Creator Tool                    : FrameMaker 10.0.2
Metadata Date                   : 2015:06:04 18:39:19-06:00
Copyright                       : 2014
Document ID                     : uuid:982d75f1-df4a-43e6-9c31-9d66785c7846
Instance ID                     : uuid:f870680a-6c52-43d4-bd66-8933477cef66
Page Mode                       : UseNone
Page Count                      : 2

EXIF Metadata provided by EXIF.tools