Delta Electronics ARUBA41 802.11 a+b+g Wireless AP User Manual 0500128 A41 IG indd

Delta Networks, Inc. 802.11 a+b+g Wireless AP 0500128 A41 IG indd

UserManual.wiki >

Delta Electronics >

ARUBA41 User Manual

Users Manual

PACKAGE CONTENTS • 1 x Aruba 41 Wireless Access Point • 1 x Quick Installation Guide (this document)Inform your supplier if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials. Use them to repack the product in case there is a need to return it.1 Install two screws in the wall or shelf. If attaching the device to drywall, we recommend using appropriate wall anchors (not included). 2 Align the Aruba 41 mount-ing slots to capture the surface screws.3 Orient the antenna. For best per-formance, swivel the antenna so that it is oriented vertically.Figure 0-1: Aruba 41 MountingAruba 4110/100 Mbps EthernetRJ-45 FemalePin-Out*POE UnusedUnusedUnusedUnused12345678ETH Rx+ (POE negative*)ETH Rx– (POE negative*)ETH Tx+ (POE positive*) ETH Tx– (POE positive*) DirectionInputOutput Figure 0-2: Aruba 41 FE PortAruba 41 Wireless Access Point Quick Installation Guide21BEFORE GETTING STARTEDBefore installing your Aruba 41 wirless access point, please ensure you have the following: • 1 x Fast Ethernet cable of required length • 1 x 802.3af compliant Power over Ethernet source (PSE) - Aruba Mobility Controller or Midspan device • 1 x Aruba Mobility Controller provisioned on the network: - with Layer 2/3 network connectivity your Aruba 41 - One of the following network services: - Aruba Discovery Protocol (ADP) - DNS server with an “A” record (see section 1; Provisioning the Aruba 41) - DHCP Server with vendor speciﬁ c options (see section 1; Provisioning the Aruba 41) Optional: • Mounting screws (not supplied)Provisioning using DHCP with Vendor Specific OptionsA standards compliant DHCP server can be conﬁ gured to return the host Aruba Mobility Controller’s IP address through Vendor Speciﬁ c Options (option 43) in the DHCP reply. If the host Mobility Controller’s IP address is obtained via DHCP, it will be used for uploading the Aruba access point’s software image and conﬁ guration. NOTE: If you have location-speciﬁ c conﬁ gurations for your Access Points, you will need to apply this conﬁ guration information using AP Reprovisioning.AP ReprovisioningOnce an AP is associated to an Aruba Mobility Controller, it is capable of being Reprovisioned if necessary. AP Reprovisioning is the process by which APs are assigned unique conﬁ guration characteristics, for example, location codes. Location codes are important for recalibration and triangulation. For details on AP Reprovisioning, see the ArubaOS User Guide.AP ProvisioningRecommended only in instances where APs require to be pre-staged or provisioned in advance of shipment and ﬁ nal network installation (suchas as Remote Access Point (RAP) deployments), in AP programming mode, AP conﬁ guration parameters are deﬁ ned on the Aruba Mobility Controller via command line interface or web interface, where they can then be uploaded to individual access points as required. Installing the Aruba 41Select a location as close as possible to the center of the intended coverage area. The service location should be free from obstructions or obvious sources of interference. Normally, the higher you place an access point or air monitor, the better its performance.The Aruba 41 can be mounted on a wall using the mounting slots on the bottom of the unit.NOTE: For dimensions, see “Product Speciﬁ cations”. Allow 5 cm (2”) additional space on the right-hand side for cables and ensure enough space for antenna articulation.Using the Built-In Mounting SlotsThe keyhole-shaped slots on the back of the Aruba 41 can be used to attach the device upright to an indoor wall or shelf.CAUTION: Do not use the mounting slots to hang the Aruba 41 from the ceiling, sideways, or in any place where it could fall on people or equipment. For more secure installation, use one of the optional mounting kits.To hang the Aruba 41 upright using the mounting slots, perform the following steps:Connecting Required CablesNOTE: Aruba 41 Access Points are intended only for installation in Environment A as deﬁ ned in IEEE 802.3.af, Power over Ethernet. All interconnected equipment must be contained within the same building, including the interconnected equipment’s associ-ated LAN connections.The 10/100 Mbps Ethernet (FE) port is used to connect the AP to a 10Base-T/100Base-TX (twisted-pair) Ethernet LAN segment. Use a 4- or 8-conductor, Category 5 UTP, straight-through FE cable.X and automatically adjusts for straight-through or cross-over cables. The maximum length for FE cables is 100 meters (325 feet). Install cables in accordance with all applicable local and national regulations and practices.Connecting Cables & Power1 Connect one end of the FE cable directly to the Aruba 41 FE port2 Connect the other end of the FE cable to one of the following: - To a network port on the Mobility Controller, or - To a network mid-span device that supports 802.3af compliant portFE Port Speciﬁ cationsThe 10/100 Mbps Ethernet (FE) port is located on the right-hand side of the Aruba 41 and has an RJ-45 female connector. The port pin-outs are shown in Figure 0-2:Verifying Successful InstallationThe integrated LEDs on the AP 41 may be used at this point to verify the AP is receiving power and initializing successfully. LED behavior indicated status as follows: Configuring the Aruba 41Once the Aruba 41 has been provisioned and installed, it will be capable of discovery and association to an Aruba Mobility Controller where the wireless and security parameters can be set. For AP conﬁ guration information, refer to the ArubaOS User GuideAAAruArubInstallation instructions for the deployment and installation of your Aruba 41 802.11a/b/g wireless access point.About the Aruba 41The Aruba 41 is part of a comprehensive wireless network solution. The device works only in conjunction with an Aruba Mobility Controller, and provides the following capabilities: • Wireless transceiver • Protocol-independent networking functionality • IEEE 802.11a or IEEE 802.11b/g operation as a wireless Access Point • IEEE 802.11a and IEEE 802.11b/g operation as a wireless Air Monitor • Compatible with IEEE 802.3af Power Over Ethernet (POE) • Can be centrally managed, conﬁ gured, and upgraded through an Aruba Mobility ControllerAAThe Aruba AP Setup ProcessSetting up an Aruba AP typically consists of a planning stage and three AP installation stages: WLAN Planning — Determine how many Aruba access points will be needed for your wireless network deployment and where they will be installed. This can be easily accom-plished using Aruba’s automated RF Plan site-survey software (available separately). This stage should have been completed during the master Aruba Mobility Controller installation and conﬁ guration. In, typical Aruba installations, the mobility con-trollers are conﬁ gured and installed prior to access points.1 AP Provisioning — Provides each Aruba access point with the initial setting required to locate the host Aruba Mobility Controller. Once the Aruba access point is associated to its host Mobility Controller, device speciﬁ c conﬁ guration may be applied as required (such as location code).2 AP Installation — Once provisioned, the AP can be physi-cally installed at its intended place of operation.3 AP Conﬁ guration — The administrator deﬁ nes the opera-tional behavior for each Aruba access point such as RF char-acteristics and security features. For speciﬁ c access point conﬁ guration information, refer to the ArubaOS User Guide.Provisioning the Aruba 41Aruba Networks, in compliance with governmental requirements, has designed the Aruba 41 such that only authorized network administrators can change these settings. For more information on Access Point conﬁ guration, refer to the ArubaOS User Guide. Goal of Access Point ProvisioningProvisioning provides the Aruba access point with basic network settings that allow it to locate the host Aruba Mobility Controller. Initial provisioning may be achieved through a number of methods, including: - Aruba Discovery Protocol (ADP) - DNS - DHCP with Vendor Speciﬁ c OptionsAruba Discovery Protocol (ADP)This is the simplist method for AP provisioning. ADP allows Aruba access pionts to be connected to the network (or directly to a Aruba Mobility Controller) and brought into operation automatically.ADP performs one key task:Obtain the IP address of the host Aruba Mobility Control-ler from which the Aruba access point will obtain its initial software load and conﬁ guration. NOTE: Additionally, the access point software can be uploaded via a standard TFTP server.ADP with Directly / Layer 2 Connected Access PointsIf your Aruba access point is directly connected to an active Ether-net interface on an Aruba Mobility Controller, then no conﬁ guration is required. You may proceed to the next step.ADP with Layer 3 Connected Access PointsIf your Aruba access point is NOT directly / Layer 2 connected to an Aruba Mobility Controller, and IP multicast routing is enabled on the host network, then ADP will multicast packets to locate a host Aruba Mobility Controller’s IP address. To ensure ADP is enabled, issue the following commands on the Master Aruba Mobility Controller:(A5000) (conﬁ g) #adp discovery enable(A5000) (conﬁ g) #adp igmp-join enableAn IP helper address on the subnet’s default gateway, mapped to the host Aruba Mobility Controller’s IP address can be also used to facilitate the multicast / broadcast based aspect of this process. Provisioning using DNSIf Layer 3 network connected, the Aruba 41 can use network based DNS to resolve a factory conﬁ gured default host name “aruba-master” to derive the host Mobility Controller IP address.To enable this, a record for “aruba-master” must be created on the network DNS server.CAUTION: Access Points are radio broadcast devices and as such are subject to governmental regulation. Network administrators responsible for the conﬁ guration and operation of Access Points must comply with local broadcast regulations. Speciﬁ cally, Access Points must use channel assignments appropriate to the location in which the Access Point will be used. 3Part 0500128LED Color(S) Activity ActionPower/Test Green On Power On, Device ReadyFlashing System InitializingLAN (10/100 Mbps)Green/Amber Off No LinkGreen On 100Mbps Link NegotiatedGreen Flashing 100Mbps Data ActivityAmber On 10Mbps Link NegotiatedAmber Flashing 10Mbps Data ActivityWLAN Green/Amber Off Wirless Radio DisabledGreen On Wirleless Radio EnabledGreen Flashing Wireless Data Activity

SpecificationsMechanicalDimensions (antenna stowed) (HxWxD) : • 107mm x 184mm x 32mm• 4.21” x 7.24” x 1.26”Weight - 0.45Kgs / 0.99LbsTemperature: • Operating: 0ºC to 50ºC (32ºF to 122ºF)• Storage: -10ºC to 70ºC (14ºF to 158ºF) Relative Humidity - 5% to 90% non-condensingAltitude - 8,000ft @ 28ºC (82.4ºF)Mounting:• Wall, cube or ceiling mountable• Enclosure supports integrated wall point / screw head mounting lugs (screw head 7mm diameter maximum)Antenna - Integrated, non-detachable articulating dual-band antennaVisual Status Indicators (LEDs):• PWR - Power / Status• ENET - Ethernet link status / Activity• WLAN G - WLAN 2.4GHz status / Activity • WLAN A - WLAN 5GHz status / ActivityElectricalEthernet: • 1 x 10/100 Base-T auto-sensing Ethernet RJ-45 Interface, MDI/MDX• IEEE 802.3af compliant Power Over Ethernet• IEEE 802.3, IEEE 802.3u• Power Over Ethernet (IEEE 802.3af compliant), 48V DC / 200mA (see Ethernet pin-out diagram for pin conﬁ guration) • Reset button Wireless LANNetwork Standards - IEEE 802.11b, IEEE 802.11g and IEEE 802.11aAntenna Type - Integral, 802.11a/b/g omni-directional high-gain antennaAntenna Gain:• 2.4 ~ 2.5GHz / 2.11dBi• 4.900 ~ 5.850 GHz / 2.07dBi Radio Technology:• Orthogonal Frequency Division Multiplexing (OFDM) • Direct Sequence Spread Spectrum (DSSS)Radio Modulation Type:• 802.11b - CCK, BPSK, QPSK• 802.11g - CCK, BPSK, QPSK,16-QAM, 64-QAM• 802.11a - BPSK, QPSK,16-QAM, 64-QAMMedia Access Control - CSMA/CA with ACKSupported Frequency Bands 2.4GHz: • 2.400 ~ 2.4835GHz (Global), channels country speciﬁ cSupported Frequency Bands 5GHz:• 5.150 ~ 5.250GHz (low band), country speciﬁ c• 5.250 ~ 5.350GHz (mid band), country speciﬁ c• 5.470 ~ 5.725GHz (Europe), country speciﬁ c• 5.725 ~ 5.825GHz GHz (high band), country speciﬁ c Operating Channels: 802.11b 802.11g 802.11a• US, Canada 11 • ETSI 13• Japan 13• US, Canada 11 • ETSI 13• Japan 13• US, Canada 12 • ETSI (up to 19)• Japan 4Complete country list available at http://www.arubanetworks.com/products/aps/certiﬁ cationData Rates: • 802.11b - 1, 2, 5.5, 11 Mbps per channel• 802.11g - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channel• 802.11a - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channelOutput Transmit Power - 100 mW maximum (or lower as conﬁ g-ured on the Aruba Mobility Controller to comply with local regula-tory requirements)Miscellaneous Functionality Maximum Clients - 64 Radio Band Selection - via Mobility Controller in software Manageability: • Management of all 802.11 parameters• Network Wide AP Management via CLI, WEB GUI and SNMPv3• Access Point Proﬁ les, managed by Geographical Location, BSSID and Radio Type Encryption (AP and Mobility Controller) - 40bit / 64bit / 128bit / 152bit WEP, TKIP, AES ComplianceFCCThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guar-antee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or televi-sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Any changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-sired operation.CAUTION STATEMENT: FCC RF Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for indoor use only. This equipment should be installed and operated with a minimum distance of 20 centimeters (7.87 inches) between the radiator and your body for 2.4 GHz and 5 GHz opera-tions. This transmitter must not be co-located or operating in con-junction with any other antenna or transmitter.This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. The FCC requires this product to be used indoors to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.CanadaThis digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.Cet appareil numérique respecte les limites de bruits radioélec-triques applicables aux appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.VCCI - Class BCE - Class BWarning—This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.EU - Class BThis product complies with EN5022 Class B and EN5024 standards.CertificationsElectromagnetic CompatibilityFCC Part 15 subpart C (15.247/15.407RSS 210 (CAN)TELEC ARIB STD-T66EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,EN 61000-4-5, EN 61000-4-6, EN 61000-4-11EN 60601-1-2: 200173/23/ECCAS/NZS 4268 Class BThe CE approval mark on back of the product indicates that it meets R&TTE Directive - EN 300 328, EN 301 489, EN 301 893SafetyUL Listed (UL60950)UL Listed (Canadian Electrical Code/CSA 22.2 No. 60950)EN60950 / IEC60950Disposal of AP40/41When the useful life of the Access Point has expired, be sure to dispose of the unit in accordance with all local code and environmental regulations. Contact your local waste man-agement or environmental agencies for details.Customer SupportMain Site: www.arubanetworks.comSupport: www.arubanetworks.com/supportE-mailSales: sales@arubanetworks.comSupport: support@arubanetworks.comTelephone NumbersMain 408-227-4500Fax 408-227-4550Sales 408-754-1201Support In the U.S.: 800-WI-FI-LAN (800-943-4526) International: 408-754-1200 1322 crossman avenue sunnyvale california 94089tel 408 227 4500 fax 408 227 4550www.arubanetworks.comB