Delta Electronics BSGIR WiFi Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	826499
Application ID	MUp6l/29An8jhAgyFZxLaA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.24kB (128016 bits)
Date Submitted	2007-08-08 00:00:00
Date Available	2007-08-08 00:00:00
Creation Date	2007-07-23 12:15:01
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2007-08-02 14:41:51
Document Title	Microsoft Word - Hardware Specification for BSG RF Module.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	JOE.CHIEN

Hardware Specification
for BSG RF Module
Block Diagram:
Processor : Atheros AR2315 single chip integrated with the MAC/baseband/radio
PHY : Realtek RTL8201 single channel, full-duplex 10/100Base-Tx transceiver
Memory : Serial Flash : 32Mbit
SDRAM : 16MByte, 16bit data bus – 1 piece of 8M x 16bit.
I/O Interface : FE , 1 x 2.4G RF SMA Conn. attaching to Antenna.
1 x 2.4G Printed Antenna
Feature :
Wi-fi Wireless Access Point
IEEE802.11b/g
2.4G RF SMA Conn. attaching to Antenna.
2.4G Printed Antenna
Max Transmit power consumption:2.4W
Rx Sensitivity
11g
11b
Test Name
Data Rate
DUT
Measured
RX Sensitivity
6Mbps
-88
RX Sensitivity
36Mbps
-73
RX Sensitivity
48Mbps
-70
RX Sensitivity
54Mbps
-68
RX Sensitivity
1Mbps
-90
RX Sensitivity
2Mbps
-87
RX Sensitivity
5.5Mbps
-86
RX Sensitivity
11Mbps
-85
Transmit Power
11g
11b
Test Name
Data Rate
DUT Measured
Transmit power
6Mbps
17 (+1.5/-1.5) dBm
Transmit power
36Mbps
16 (+1.5/-1.5) dBm
Transmit power
48Mbps
15 (+1.5/-1.5) dBm
Transmit power
54Mbps
14 (+1.5/-1.5) dBm
Transmit power
1Mbps
17 (+1.5/-1.5) dBm
Transmit power
2Mbps
17 (+1.5/-1.5) dBm
Transmit power
5.5Mbps
17 (+1.5/-1.5) dBm
Transmit power
11Mbps
17 (+1.5/-1.5) dBm
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance
requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host this
module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority to
operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna
while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure
guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size
of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users
manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: XXXXX ". If the size of the
end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This
device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:08:02 14:41:51+08:00
Create Date                     : 2007:07:23 12:15:01+08:00
Metadata Date                   : 2007:08:02 14:41:51+08:00
Format                          : application/pdf
Title                           : Microsoft Word - Hardware Specification for BSG RF Module.doc
Creator                         : JOE.CHIEN
Document ID                     : uuid:a1f2f1f3-ba47-4c05-a461-ab0bf08f9b95
Instance ID                     : uuid:5b1d0613-365a-43a2-946b-4be23dfc13f5
Page Count                      : 4
Author                          : JOE.CHIEN

EXIF Metadata provided by EXIF.tools