Delta Electronics E804WAG Dual-Band Wireless A+G Router User Manual P74743 F6D3230 4 AG man 12 04 indd

Download:
Mirror Download [FCC.gov]
Document ID	501622
Application ID	cq4hHoL6i03xPPI/8jLeIw==
Document Description	Users manual 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	188.17kB (2352168 bits)
Date Submitted	2004-12-28 00:00:00
Date Available	2004-12-28 00:00:00
Creation Date	2004-12-28 15:53:21
Producing Software	Adobe PDF Library 6.0
Document Lastmod	2004-12-28 15:53:59
Document Title	P74743_F6D3230-4_AG_man_12-04.indd
Document Creator	Adobe InDesign CS (3.0.1)

Connecting and Configuring the Router
Setting your Internet Service Provider (ISP) Connection Type
to Static IP
(1)
(2)
(3)
(4)
1.
IP Address
Provided by your ISP. Enter your IP address here.
2.
Subnet Mask
Provided by your ISP. Enter your subnet mask here.
3.
ISP Gateway Address
Provided by your ISP. Enter the ISP gateway address here.
29
section
A static IP address connection type is less common than other connection
types. If your ISP uses static IP addressing, you will need your IP address,
subnet mask, and ISP gateway address. This information is available from
your ISP or on the paperwork that your ISP left with you. Type in your
information, then click “Apply Changes” (4). After you apply the changes,
the Internet Status indicator will read “connection OK” if your Router is set
up properly.
Connecting and Configuring the Router
Setting your ISP Connection Type to PPPoE
Most DSL providers use PPPoE as the connection type. If you use a
DSL modem to connect to the Internet, your ISP may use PPPoE to
log you into the service. If you have an Internet connection in your
home or small office that doesn’t require a modem, you may also
use PPPoE.
Your connection type is PPPoE if:
a)
Your ISP gave you a user name and password which is required
to connect to the Internet.
b)
Your ISP gave you software such as WinPOET or Enternet300 that
you use to connect to the Internet.
or
c)
You have to double-click on a desktop icon other than your
browser to get on the Internet.
30
Connecting and Configuring the Router
(3)
(4)
1.
User Name
This space is provided to type in your user name that was
assigned by your ISP.
2.
Password
Type in your password and retype it into the “Retype Password”
box to confirm it.
3.
Service Name
A Service name is rarely required by an ISP. If you are not sure if
your ISP requires a service name, leave this blank.
4.
MTU
The MTU setting should never be changed unless your ISP gives
you a specific MTU setting. Making changes to the MTU setting
can cause problems with your Internet connection including
disconnection from the Internet, slow Internet access, and
problems with Internet applications working properly.
31
section
(1)
(2)
Connecting and Configuring the Router
Setting your Internet Service Provider (ISP) Connection Type to
Point-to-Point Tunneling Protocol (PPTP)
[European Countries Only]. Some ISPs require a connection using
PPTP protocol, a type of connection most common in European
countries. This sets up a direct connection to the ISP’s system. Type
in the information provided by your ISP in the space provided. When
you have finished, click “Apply Changes” (9). After you apply the
changes, the Internet Status indicator will read “connection OK” if
your Router is set up properly.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
1.
PPTP Account
2.
PPTP Password
Provided by your ISP. Enter your PPTP account name here.
Type in your password and retype it into the “Retype Password”
box to confirm it.
3.
Host Name
4.
Service IP Address
Provided by your ISP. Enter your host name here.
Provided by your ISP. Enter your service IP address here.
32
Connecting and Configuring the Router
5.
My IP Address
Provided by your ISP. Enter the IP address here.
6.
My Subnet Mask
7.
Connection ID (optional)
Provided by your ISP. If your ISP did not give you a connection
ID, leave this blank.
8.
Disconnect after X….
The “Disconnect” feature is used to automatically disconnect the
Router from your ISP when there is no activity for a specified
period of time. For instance, placing a check mark next to this
option and entering “5” into the minute field will cause the Router
to disconnect from the Internet after five minutes of no Internet
activity. This option should be used if you pay for your Internet
service by the minute.
33
section
Provided by your ISP. Enter the IP address here.
Connecting and Configuring the Router
Setting your Connection Type if you are a Telstra® BigPond User
[Australia Only] Your user name and password are provided to you by
Telstra BigPond. Enter this information below. Choosing your state
from the drop-down menu (6) will automatically fill in your login server
IP address. If your login server address is different than one provided
here, you may manually enter the login server IP address by placing a
check in the box next to “User decide login server manually” (4) and
type in the address next to “Login Server” (5). When you have entered
all of your information, click “Apply Changes” (7). After you apply the
changes, the Internet Status indicator will read “connection OK” if
your Router is set up properly.
(1)
(6)
(2)
(3)
(4)
(7)
(5)
1.
Select your State
Select your state from the drop-down menu (6). The “Login
Server” box will automatically be filled in with an IP address.
If for some reason this address does not match the address
that Telstra has given, you can manually enter the login server
address. See “User decide login server manually” (4).
2.
User Name
Provided by your ISP. Type in your user name here.
3.
Password
Type in your password and retype it into the “Retype Password”
box to confirm it.
4.
User Decide Login Server Manually
If your login server IP address is not available in the “Select Your
State” drop-down menu (6), you may manually enter the login
server IP address by placing a check in the box next to “User
decide login server manually” and type in the address next to
“Login Server” (5).
34
Connecting and Configuring the Router
Setting Custom Domain Name Server (DNS) Settings
(1)
(2)
35
section
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locater (URLs) like “www.belkin.
com” to IP addresses. Many Internet Service Providers (ISPs) do not
require you to enter this information into the Router. The “Automatic
from ISP” box (1) should be checked if your ISP did not give you a
specific DNS address. If you are using a static IP connection type,
then you may need to enter a specific DNS address and secondary
DNS address for your connection to work properly. If your connection
type is dynamic or PPPoE, it is likely that you do not have to enter a
DNS address. Leave the “Automatic from ISP” box checked. To enter
the DNS address settings, uncheck the “Automatic from ISP” box and
enter your DNS entries in the spaces provided. Click “Apply Changes”
(2) to save the settings.
Connecting and Configuring the Router
Configuring your WAN Media Access Controller (MAC) Address
All network components, including cards, adapters, and routers, have
a unique “serial number” called a MAC address. Your Internet Service
Provider may record the MAC address of your computer’s adapter and
only let that particular computer connect to the Internet service. When
you install the Router, its own MAC address will be “seen” by the
ISP and may cause the connection not to work. Belkin has provided
the ability to clone (copy) the MAC address of the computer into the
Router. This MAC address, in turn, will be seen by the ISP’s system as
the original MAC address and will allow the connection to work. If you
are not sure whether your ISP needs to see the original MAC address,
simply clone the MAC address of the computer that was originally
connected to the modem. Cloning the address will not cause any
problems with your network.
36
Connecting and Configuring the Router
Cloning your MAC Address
Entering a Specific MAC Address
In certain circumstances you may need a specific WAN MAC address.
You can manually enter one in the “MAC Address” page. Type in a
MAC address in the spaces provided (2) and click “Apply Changes”
(3) to save the changes. The Router’s WAN MAC address will now be
changed to the MAC address you specified.
(2)
(1)
(3)
37
section
To clone your MAC address, make sure that you are using the
computer that was ORIGINALLY CONNECTED to your modem before
the Router was installed. Click the “Clone” button (1). Click “Apply
Changes” (3). Your MAC address is now cloned to the Router.
Using the Web-Based Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do
not type in anything else such as “http://” or “www”) then press the
“Enter” key.
You will see the Router’s home page in your browser window.
Viewing the LAN Settings
Clicking on the header of the LAN tab (1) will take you to the LAN
tab’s header page. A quick description of the functions can be
found here. To view the settings or make changes to any of the LAN
settings, click on “LAN Settings” (2) or to view the list of connected
computers, click on “DHCP Client List” (3).
(1)
(2)
(3)
38
Using the Web-Based Advanced User Interface
Changing LAN Settings
All settings for the internal LAN setup of the Router can be viewed
and changed here.
(1)
(3)
(4)
(5)
(6)
1.
IP Address
The “IP address” is the internal IP address of the Router. The
default IP address is “192.168.2.1”. To access the advanced
setup interface, type this IP address into the address bar of your
browser. This address can be changed if needed. To change the
IP address, type in the new IP address and click “Apply Changes”.
The IP address you choose should be a non-routable IP.
Examples of a non-routable IP are:
192.168.x.x (where x is anything between 0 and 255)
10.x.x.x (where x is anything between 0 and 255)
172.y.x.x (where y is anything from 16 to 31, and x is anything
between 0 and 255)
2.
Subnet Mask
There is no need to change the subnet mask. This is a unique,
advanced feature of your Belkin Router. It is possible to change
the subnet mask if necessary; however, do NOT make changes to
the subnet mask unless you have a specific reason to do so. The
default setting is “255.255.255.0”.
3.
DHCP Server
The DHCP server function makes setting up a network very easy
by assigning IP addresses to each computer on the network
39
section
(2)
Using the Web-Based Advanced User Interface
automatically. The default setting is “On”. The DHCP server
can be turned OFF if necessary; however, in order to do so you
must manually set a static IP address for each computer on
your network. To turn off the DHCP server, select “Off” and click
“Apply Changes”.
4.
IP Pool
The range of IP addresses set aside for dynamic assignment to the
computers on your network. The default is 2–100 (99 computers). If
you want to change this number, you can do so by entering a new
starting and ending IP address and clicking on “Apply Changes”.
The DHCP server can assign 100 IP addresses automatically. This
means that you cannot specify an IP address pool larger than 100
computers. For example, starting at 50 means you have to end at
150 or lower so as not to exceed the 100-client limit. The starting
IP address must be lower in number than the ending IP address.
5.
Lease Time
The length of time the DHCP server will reserve the IP address
for each computer. We recommend that you leave the lease
time set to “Forever”. The default setting is “Forever”, meaning
that any time a computer is assigned an IP address by the
DHCP server, the IP address will not change for that particular
computer. Setting lease times for shorter intervals such as one
day or one hour frees IP addresses after the specified period of
time. This also means that a particular computer’s IP address
may change over time. If you have set any of the other advanced
features of the Router such as DMZ or client IP filters, these are
dependent on the IP address. For this reason, you will not want
the IP address to change.
6.
Local Domain Name
The default setting is “Belkin”. You can set a local domain name
(network name) for your network. There is no need to change this
setting unless you have a specific advanced need to do so. You can
name the network anything you want such as “MY NETWORK”.
40

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2004:12:28 15:53:59+08:00
Create Date                     : 2004:12:28 15:53:21+08:00
Title                           : P74743_F6D3230-4_AG_man_12-04.indd
Creator                         : Adobe InDesign CS (3.0.1)
Producer                        : Adobe PDF Library 6.0
Page Count                      : 12
Mod Date                        : 2004:12:28 15:53:59+08:00
Creation Date                   : 2004:12:28 15:53:21+08:00
Metadata Date                   : 2004:12:28 15:53:59+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools