Denon DRA 685 User Manual AM FM STEREO RECEIVER Manuals And Guides L0211064
DENON Receivers Manual L0211064 DENON Receivers Owner's Manual, DENON Receivers installation guides
User Manual: Denon DRA-685 DRA-685 DENON AM-FM STEREO RECEIVER - Manuals and Guides View the owners manual for your DENON AM-FM STEREO RECEIVER #DRA685. Home:Electronics Parts:Denon Parts:Denon AM-FM STEREO RECEIVER Manual
Open the PDF directly: View PDF .
Page Count: 56
Download | |
Open PDF In Browser | View PDF |
AM-FM STEREO RECEIVER DRA-685 OPERATING INSTRUCTIONS MODE D'EMPLOI jr Z_C Mull Room o _ FOR ENGL(SH READERS • • o o 0 PAGE 0 0 0 2 o- PAGE 0 0 "SERIAL NO. 0 0 oO Oo ...... POUR LES LECTEURS FRANCAIS • • PAGE 2, 30 PAGE 55 Nous vous remercions pour I'achat de cet appareil. Pour &tre s_r de profiter au maximum de toutes les caracteristiques qu'offre cet appareil, life avec soin ces instructions et bien utiliser I'appareil. Toujours conserver ce mode d'emploi pour s'y referer ulterieurement en cas de question ou de problbme. "NO. DE SERIE UNIT SERIAL NUMBER THE REAR OF THE CABINET 0 29 We greatly appreciate your purchase of this unit. To be sure you take maximum advantage of all the features this unit has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. PLEASE RECORD 0 / FOR FUTURE ATTACHED TO REFERENCE" PRIERE DE NOTER LE NUMERO DE SERIE DE L'APPAREIL INSCRIT A L'ARRIERE DU COFFRET DE FA(_ON A POUVOIR LE CONSULTER EN CAS DE PROBLEME." [_e,]_.,,_ F_ _] • SAFETY PRECAUTIONS CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF INTERODUIRE LA PLUG TO WIDE SLOT, FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRJQUES, CAUTION: REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. LAME LA PLUS LARGE CORRESPONDANTE DE LA FICHE DANS LA BORNE DE LA PRISE ET POUSSER JUSQU' The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This device complies with Part I5 of the FCC Rules Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus meets all requirements Canadian Interference-Causing Equipment Regulations. The exclamation point within REDUCE THE ELECTRIC SHOCK, THIS APPLIANCE MOISTURE. RISK Cet appareil num@rique de la classe B respecte toutes exlgences du R_glement sur le materiel brouilleur du Canada. • Avo d h gh temperat=Jres A}}ow for sufficient heat r stalled on a rack Eviter Tent des temperatures compte dr re s ffsarte dissersion @levees dispersion lots de I'installation OF FIRE RELATIVES A L'UTILISATION • Keep dust • Prot@ger poussi_re the 2 flom • Unplug the power cord when r ot using the set for long periods of time D6brancler le cordon d'almentation }orsque I'appareil contre r'est sas du water, I'humidd_, utilis@ pendant I'eau and • • Do not let foreign obiects in the set Ne pas }aissel des obets @trangers 'a_areil • Do not }et nsect cides, benzene, come in contact with the set • Ne pas mettre en contact des insecticides, benzane et un diluant avec I'appare dans et la d@branchement du • Donotobstructt • Nepasobstruer ventilation e ventilation estro holes) holes sdra@ration and thinner d de Iongues avec * (For sets with Iors moisture, de chaleur Hand}e the sower cord carefully Hold the plug when unplugging the cord Mampuler le cordon d'al mentat or pr6ca tlon Tenir la prise cordon free sur une 6tag_re I'appareil p@riodes • set when • • OR DO NOT EXPOSE TO RAIN OR • NOTE ON USE / OBSERVATIONS • of the an equilateral presence of important triangle is intended to alert operating the user to and the maintenance (servicing) instructions in the literature accompanying the appliance. WARNING:To AU FOND • Never • way Ne jamas d@monter ou rood drune mani@re ou d'une autre disassembe or modify the fier set in any I'apsarel les SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating should be read before the product is operated. instructions 2. Retain Instructions - The safety and operating should be retained for future reference instructions 3. Heed Warnings - AII warnings on the product operating instructions should be adhered to 4. Follow Instructions be followed. 5. Cleaning cleaning 6. Attachments - Do not use attachments not recommended the product manufacturer as they may cause hazards 7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. g. 10. 13 Power-Cord Protection - Power=supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 15 Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built=up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the leaddn wire to an antenna discharge unit, size of grounding conductors, location of antenna=discharge unit, connection to grounding electrodes, and requirements for the grounding electrode See Figure A. 16 Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and powerqine surges 17 Power LinesAn outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. A product and cart combination should be moved with care Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn 18 Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19 Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short=out parts that could result in a fire or electric shock Never spill liquid of any kind on the product. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to 20. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service. 22 Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire, electric shock, or other hazards 23 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24 Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25 Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat and in the - All operating and use instructions should - Unplug this product from the wall outlet before Do not use liquid cleaners or aerosol cleaners. by Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 11. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization - This product may be equipped with a polarized alternating=current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature If you are unable to insert the plug fully into the outlet, try reversing the plug If the plug should still fail to fit, contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug (NEC ART 25O PART H] NEC NATIONAL ELECTR_CA_ CODE 3 _t]]E-t]][ • INTRODUCTION Thank you for choosing the DENON AM-FM Stereo receiver. This remarkable component has been engineered to provide outstanding high fidelity reproduction of your favorite music sources. As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this manual before proceeding TABLE OF CONTENTS Before Using 4 Operations Cautions on Installation ...................................................... .................................................................. 5 Listening to the Radio ................................................ Cautions on Handling ......................................................... 5 Features 5 ........................................................................ Connections ............................................................... Part Names and Functions .......................................... Remote Control Unit ................................................... El ............................................................... Initialization of the Microprocessor Last function 6-10 El Specifications .................................... 27 memory ...................................................... Troubleshooting 10, 11 17-23 24-26 27 ............................................................ 28 ............................................................... 29 12-17 • ACCESSORIES Check that the following (1) Operating instructions parts are included in addition to the main unit: ................................................... (2) Warranty ..................................................................... (3) Service station lisl ......................................................... (4) Remote control unit (RC_872) .......................................... (RC-873) .......................................... ® (RC-872) [] 2 (R03/AAA) ...................................................... (6} AM loop antenna ......................................................... (7} FM indoor antenna ......................................................... 2 1 1 ® ® (RC-873) BEFORE USING Pay attention to the following before using this unit: • Moving the set To prevent short • Store this instructions circuits or damaged wires in the connection cords, always unplug the power cord and disconnect the connection cords between all other audio components when moving the set. • Before turning the power operation switch on Check once again that all connections are proper and that there are not problems with the connection cords. Always set the power operation switch to the standby position before connecting and disconnecting connection cords. 4 (5} Batteries (R6P/AA) ......................................................... in a safe place. After reading, store this instructions safe place along with the warranty • Note that the illustrations in this instructions the actual set for explanation purposes. in a may differ from [] CAUTIONS ///////////////////////////////////////////////,, ON INSTALLATION N 10 cm or more Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV. If this happens, take the following steps: • Install this unit as far as possible from the tuner or TV • Set the antenna wires from the tuner or TV away from this unit's power cord and input/output connection cords. • Noise or disturbance tends to occur particularly when using indoor antennas or 300 £_/ohms feeder wires. We recommend outdoor antennas and 75 £_/ohms coaxial cables. * ....... OO © [ "//////////////////////////////////////////////, using 10 Cm or more For heat dispersal, leave at least 10 cm of space between the top, back and sides of this unit and the wall or other components. Wall //////////////////////////////////// [] CAUTIONS • Switching connected the ON HANDLING input function when input jacks are not A clickhTg noise may be produced if the input function is switched when nothing is connected to the input jacks. If this happens, either turn down the VOLUME control or connect components to the input jacks. • Muting • Whenever the power operation switch is in the STANDBY state, the apparatus is still connected on some AC line voltages. Please be sure to unplug the cord when you leave home for, say, a vacation. of PRE OUT jacks The PRE OUT iacks include a muting circuit Because of this, the output signals are greatly reduced for several seconds after the power operation switch is turned on If the volume is turned up during this time, the output will be very high after the muting circuit stops functioning. Always wait until the muting circuit turns off before adjusting the volume [] 1. FEATURES Multi Room Music Entertainment Multi Source Function: System This unit's Multi Source function lets you select different audio or video sources for viewing or listening Different sources can thus be enjoyed in the main room and the subroom simultaneously This novel feature gives you considerable flexibility when setting up and enjoying your system with the this unit. The output level, adjustable by the remote commander, is as much as lV, enough to operate the optional power amplifier placed in a subroom 2, Powerful, Versatile Amplifier 4. Remote Control Functions • Remote Control unit with pre-memory function (RC_872): This unit comes with a remote control unit equipped with a pro-memory function. The remote control command codes for DENON remote controllable AV components as well as for DVD players, video decks, TVs, etc, of other major manufacturers are prestored in the memory • Multi Source Remote Control Unit (RC=873): This unit comes with the Multi Source Remote Control Unit, which operates the Multi Source Output and commands the receiver to select the function, recalling preset stations, and adjust the volume level from a subroom High-Quality Power Amplifier: High-speed, high-power transistors employed in a rational circuit configuration reflect DENON'S advanced amplifier technology and ensure a very hefty, dean power output. 3. Signal Level Divided Construction (SLDC) The circuits handling low level and highqevel signals have been divided into separate blocks to ensure that influences from these signals on each other are held to an absolute minimum This chassis design in the this unit is called the Signal Level Divided Construction (SLDC) Signals for output are cleaner than before, allowing them to be reproduced with even greater fidelity and clarity. 5 [] CONNECTIONS • Do not plug in the power cord until aft connections have been completed. • Be sure to connect the left and right channels propedy (left with left, right with right) • Insert the plugs securely. Incomplete connections will result in the generation of noise • Use the AC OUTLETS for audio equipment only. Do not use them for hair driers, etc. • Note that binding pin plug cords together with power cords or placing them near a power transformer will result in generating hum or other noise • If hum or other no4se is produced when the ground wire is connected, disconnect it • Noise or humming may be generated if a connected component is used independently without turning the power of this unit on If this happens, turn on the power of the this unit. OL >JT CD player L I Connecting _oo _o °° a CD player I Connect the CD player's analog output jacks (ANALOG OUTPUT) to this unit's CD iacks using pin plug cords¸ © Ground LINE OUT Use these jacks when using another separate amplifier or a pre-maln ampl fief wire AC 120 V, 60 Hz i AUX OUT LINE iN RC-616 (Sold Separately) Infrared retransmitter LiNE IN RC-617 (Sold Separately) Infrared sensor Tape deck DENON [] OUTPUT INPUT Power amplifier [ Connecting - a tape deck ] Connections for recording: Co_wlect the tape deck's recording input iacks (LINE IN or REC) to this u_fit's tape recording (OUT) jacks using pin plug cords Connections for playback: Connect the tape deck's playback output iacks (LINE OUT or PB) to this unt's tape playback (IN) jacks using pin plug cords l [ Connecting the AC OUTLETS } AC OUTLETS • SWITCHED (total capacity - 120 W (1 A) The power to this outlet is turned on and off in conjunction with the POWER operation switch on the main unit, and when the power is switched between on and otandby from the remote control unit¸ No power is supplied from these outlets when this unit's power is at standby¸ Never connect equipment whose total capacity is above 120 W (1 A) NOTE: Use the AC OUTLETS driers, etc 6 for audio equipment only Do not use them for hair [_i_e]]![.l][ • To connect the video signal, connect using a 75 _/ohms video signal cable cord Using an improper cable can result in a drop in sound quality • When making connections, also refer to the operating instructions of the other components I Connecting TV/DBS TV or DBS tuner k OdT o VIDEa 1] 5 © © • Connect the TV's or DBS tuner's video output iack (VDEO OUTPUT) to the _ (yellow) VAUX IN jack using a 75 _Z/uhms video coaxial pin plug cord • Connect the TV's or DBS tuner's audio output jacks (AUDIO OUTPUT) to the _ VAUX IN jacks using pin plug cords OUT • Connect the TV's video input jack (VDEO INPUT) to the _ MONITOR OUT jack using a 75 _/uhms video coaxial pin plug cord LD player (VDP) or DVD player L OU .... I Connecting 5 © © Monitor _V _J _Z a video disc player VDP or a DVD player I • Connect the video disc player's (DVD player's) video output jack (VIDEO OUTPUT) to the _ (yellow) DVD/VDP IN jack using a 75 £_/ohms video coaxial pin plug cord • Connect the video disc player's AUDIO OUTPUT) to the _ VIDEO (DVD player's) analog audio output iacks (ANALOG DVD/VDP IN jacks using pn plug cords OUT VIDEO Connecting MONITOR a TV/DBS tuner IN a video decks ] Video input/output connections: • Connect the video deck's video output jack (VIDEO OUT) to the (yellow} VCR IN jack, and the video deck's video input jack (VIDEO IN) to the _ (yellow) VCR OUT jack using 75 _/ohms video coaxial pin plug cords Connecting the audio output jacks • Connect the video deck audio output jacks (AUDIO OUT) to the VCR IN jacks, and the video deck's audio input iacks (AUDIO IN) to the _ VCR OUT jacks using pin plug cords¸ 7 ANTENNA AM Accesso LOOP W) (An DIRECTION OF BROADCASTING STATION / FM ANTENNA _?@ _, 75_ohms COAXIAL CABLE ..... @@ o ......... @ ,_S_D'_D_aVD 0,, ..... @ @..... _,o_@ @@, ............ @@1@@,,_, _ _LUO0 AM OUTDOOR ANTENNA ® R_4_T_C_NR_ i ///_ //// GROUND FM INDOOR ANTENNA (An Accesso W) fANI loop antenna assembly a rite © (_ Connection Connect to the AM Remove the vinyl tie and take out the Bend in the reverse connection direction line a With the antenna on top any stabJe 1 Loosen by turning counterclockwise n1_8 terminals of AM antennas 2 Inset tee cord 3 Tighten by turning clockwise Note to CATV system installer: This reminder is provided to call the CAT\! system installer's attention to Art cle 82040 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground snail be connected to the ground ng system of the building, as close to the point of cable entry as practical '_ suFrace Mount NOTES: b Wtt_{{_t/Iteantwe_nlna _ _1_ • DO not connect two FM antennas simLfltaneously • Even if an external AM antenna is used, do not disconnect _1_ _L_ AM loop antenna Insdlation hole Mount on wall, etc 8 J • Make sure AM loop antenna lead terminaB the panel do not touch metal parts of • Connect the speaker terminals with the speakers making sure that like polarities are matched (_ with (_, e with e) Mismatching of Speaker Impedance • When speaker systems A and B are use separately, speakers with polarities will result in weak central sound, unclear orientation of the vanous instruments, and the sense of direction of the stereo being impaired • When making connections, take care that none of the individual conductors of the speaker cord come in contact with adjacent terminals, with other speaker cord conductors, or with the rear panel an impedance of 4 to I6 £_/ohms can be connected for use as speakers • Be careful when using two pairs of speakers {A + B) at the same time, since use of speakers with an impedance of 8 to 16 £_/ohms • The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an impedance lower than the specified impedance are connected NOTE: NEVER touch the speaker terminals when the power is on. Doing so could result in electric shocks. Connecting the speaker terminals Connecting banana plugs 1 Loosen by turning 2 Insert the cord 3 Tighten by turning clockwise counterdockwise bananaplug =4> Turn clockwise to tighten, then insert the banana plug [SPEAKER SYSTEMS1 I SPEAKERSYSTEMS ] System B System A • Precautions when connecting speakers If a speaker is placed near a TV or video monitor, the Colors on the screen may be disturbed by the speaker's magnetism¸ If this should happen, move the speaker away to a position where it does not have this effect¸ m m 9 [] • This unit is equipped with a high-speed protection circuit. This circuit protects the internal circuitry from damage due to large currents flowing if the speaker jacks are not completely connected or if an output is generated by a short circuit. In such a case, the protection circuit will operate to cut off the output to the speakers. Should this happen, turn the power off and check the speaker connections. Then turn the power on again. After muting for several seconds, the receiver should be operating normally. If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center. • The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 £)/ohms) are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set's power, wait for the set to cool down, improve the ventilation around the set, then turn the power back on. PART NAMES AND FUNCTIONS • For details on the functions of these parts, refer to the pages given in parentheses (). T O ) ................. _ I _-_ I_2._NN_ Multi Room ...................................... ,.9. _. O._..O._..O. @. O. O. @ O Power operation switch (17) BALANCE control ......................................................... (18) Headphone jacks (PHONES) .......................................... (22) VOLUME control (18) SPEAKER A/B buttons ................................................... (17) Preset memory selector buttons VIDEO SELECT button (22) Display MULTI SOURCE buttons ................................................ .......................................... .................................... (26) Power indicator ............................................................ (17) (18) Remote control sensor (REMOTE SENSOR) (12) LOUDNESS button (18) TUNING buttons (18) Input source selector buttons ...................................................... control TREBLE adjustment control ............................................. .......................................... (19, 20) ......................................................... TONE DEFECT button ................................................... BASS adjustment 10 ................................................ (18) ..................... ................................................... ....................................... (25, 26) (18) [_[t]_t]][ • For details on the functions of these parts, refer to the pages given in parentheses (). t tRrenms_itt_O:_rO[ : gr:a[ ...................... I Modese[ector t POWER buttons switch ............... ..................... (12) (13, 14) I (16,17} I C:nS:Ttttt'tt11: ....................... ,18, _::t::mtT?:: ?'it:t: ................... (28_ I MULTI SOURCE button I System buttons ............ {19, 20) t (DECK, VCR) {13, 16) I" t/_4%?C;;-%VO.DP/ ......... /13,18/ ,_1SPEAKER Bbutton ...................... 117/I I SPEAKER A button ........................ (17) I t Vu°ttL°:'?E ?::K........................... ,18/ I VIDEO SELECT button I System buttons (TV) .................. ..................... (22) I I MUTING button Lt (16) I" ........................... STATUS button .............................. {22) I {23) I NOTE: • The shaded buttons _ do not funct on with the this unit (Nothing happens when they are pressed) 11 [] REMOTE CONTROL UNIT Following the procedure outlined below, insert the batteries before using the remote control unit. Point the remote control unit at the remote control sensor as shown on the diagram at the left NOTES: • The remote control unit can be used from a straight distance of approximately 7 meters/23 feet, but this distance will shorten or operation will become difficult if there are obstacles between the remote control unit and the remote control sensor, if the remote control sensor is exposed to direct sunlight or other strong light, or if operated from an angle. • Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible. Approx 7 m/23 feet For remote control unit (RC-872} 0_) Press as shown by the arrow and slide off. For multi-source ,:.2_Insert the R6P/AA batteries shown on the diagram. properly, as _3) Close the lid. remote control unit (RC-873) 0_) Press as shown by the arrow and slide off. (2) Insert the R03/AAA batteries shown on the diagram. properly, as _3) Close the lid. NOTES: • Be sure the polarities are correct. (See the illustration inside the battery compartment) • Remove the batteries if the remote control transmitter will not be used for an extended period of time. • If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc Clean the battery compartment thoroughly before installing new batteries • Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit ts operated nearby the set (The included battery is only for verifying operation Replace it with a new battery as soon as possible) • When replacing the batteries, after removing them wait for about one minute before inserting the new batteries 12 [_i_t]]![.tll DENON remote_controllable audio components can be controlled using this unit's remote control unit. Note that some components, however, cannot be operated with this remote control unit --1 Set the slide (CD switch to the position for the component be operated or MD/CD_R). -2-C 2-b m to CD MD/CD-R Use the buttons shown below to operate the audio component. For details, refer to the respective component's manual. a. For CD player and MD/CD-R 44,1_1_ : • : P,: 1_1411D,_4: II : DISC : SKIP+ Manual search (reverse and forward) Stop Play Auto search Pause Disc selection (CD changer only) b. For tape deck (DECK) Reverse Forward 44 Stop Forward play Reverse play c, For TUNER SHIFT CHANNEL: + ,- Switch preset channel range Preset channel up/down NOTE: • Tape deck (DECK) and TUNER can be operated when the switch is at "AUDIO" DENON components position. can be operated by setting the preset memory for MD or CD-R --1 Set the slide switch to "MD/CD-R". CD MD/CD-R Holding in theyou PLAY press for the components want(1_) to button, set (Refer to the tablebutton 1) Table m 1: Combinations Codes of Personal System VOLUME PLAY(I_) -2 CD_R NOTE: • The memory can only be preset for either the MD or the CD-R. _4 _ Preset codes set upon shipment from the factory and when reset. 13 DENON and other makes of components possible for some models. can be operated by setting the preset memory for your make of video component. Set the slide switch to "VIDEO". --I -2,3 -A CD Operation is not MD/CD-R ..L 2 Holding in the POWER button of the components (DVD/VDP, VCR or TV) you want to set, press the button for the corresponding manufacturer in block A. (Refer to Table 2.) Next, while the BPOWER button for the holding code in in block button, press the (Refer to Table 2.) To continue registering This remote control unit can be used to operate components manufacturer of the component as shown on Table 2. Table 2: Combinations other components, of other manufacturers repeat steps 2 to 3 without using the learning function of Personal System Codes for Different Manufacturers "DVD" "VDP" MASTER VOL MASTER VOL MUTING A MASTERVOL _ [_ MUTING } MASTER DVD/YDP DVD/YDP MULTi DENON A DENON B -- DENON VOL A (_ DENON } B DENON C MULTI VCR VCR MITUBISHI -- -- MULTi VOL • MULTI VOL • PANASONIC -- -- TAPE MONITOR PANASONIC -- -- TAPE MONITOR TUNER TUNER SONY -- -- SHIFT SHIFT PIONEER -- -- MULTi VOL • MULTI VOL • PHILIPS -- -- RCA -- -- MAGNAVOX -- -- TAPE SONY -- -- TAPE TAPE PIONEER -- -- TAPE TOSHIBA -- -- TUNER [_ TAPE @ TUNER [_ TAPE @ TAPE TAPE } TAPE @ TUNER _ TAPE @ TUNER _ NOTE: • The memory can only be preset for either the DVD or the VDP. _ Preset codes set upon shipment from the factory and when reset 14 by registering _ the "VCR" "TV" MASTER VOL B A _ MASTER VOL MUTING MUTING MASTER VOL MASTER VOL DVD/VDP DVD/VDP MULTi HITACHI A VCR MITUBISHi HETACHI B A MITUBISHI B MITUBISHE C -A MITUBISHI -B PANASONIC A PANASONIC MULTI VOL • PANASONIC JVC (VICTOR) A JVC (VICTOR) B JVC (VICTOR) C TAPE MONITOR JVC (VICTOR) -- -- TUNER SONY A SONY B SONY C SHIFT PIONEER MULTi VOL • TOSHIBA TAPE SANYO A SANYO B TAPE SHARP A SHARP B TUNER NEC A NEG B NEC C TAPE PHILIPS A PHILIPS B PHLIPS TAPE RCA A RCA B TAPE GENERAL ELECTREC A GENERAL ELECTRIC (_ _ -A MAGNAVOX TOSHIBA A C MITUBISHI TAPE MONITOR TUNER PANASONIC HITACHI VCR MULTi VOL • _-_ B MULTI B TUNER SONY -- -- SHIFT PIONEER -- -- MULTi VOL • TOSHIBA -- -- -- TAPE SANYO -- -- -- TAPE SHARP -- -- TUNER NEC -- -- [_ C TAPE PHILIPS -- -- -- TAPE RCA -- -- TAPE GENERAL ELECTRIC A B B PANASONIC -B MAGNAVOX A MAGNAVOX C TUNER (_ MAGNAVOX GENERAL ELECTRIC B -- __ -- Preset codes set upon shipment from the factory and when reset NOTES: • The signals for the pressed buttons are emitted while setting the preset memory To avoid accidental operation, cover the remote control unit's transmitting window while setting the preset memory. • Some models and years of manufacture of components of the manufacturers listed on Table 2 cannot be used • The unit is equipped with several types of remote control codes which depend on the manufacturer. If there is no operation when set to A, please change the setting to B or C and try again 15 1 Set the slide switch to "VIDEO". CD MD/CD-R AUDIO(_ VIDEO --1 --2 the video •Operate For details, refer component. to the component's operating instructions. •_ Some models cannot be operated with this remote control unit. a. For DVD player POWER -2-c : Power on/off • I_ 1_1_1,11_1_1 n TITLE MENU DISPLAY SET UP RETURN •, • _1, I_ SELECT DISC SKIP + : : : : : : : : : Stop Play Auto search (cue) Pause Call out title Call out menu Switch display DVD setup Menu return : : : : Cursor up/down Cursor left/right Enter setting Disc selection NOTE: i_l_Tul_ U_HA¥ Some manufacturers use different names for the DVD remote control buttons, so also refer to the instructions on remote control for that component. b. For video disc player (VDP} c, For video deck (VCR} d. For TV O^_E:::>^O 00 0o [_ GD I_1 G3 (:3D (:_ (2El I2D [Z3 (2D (3D GD POWER 414,1_1_ : Power on/off : Manual search (reverse and forward) POWER : Power on/off 4_11,1_1 _ : Manual search (reverse and forward) • I_ 144,11_J_ II : : : : • : Stop I_ : Play CHANNEL: Switch channel Stop Play Auto search (cue) Pause +,- POWER VOLUME • ,¥ CHANNEL: + : Power on/off : Volume up/down Switch channel ,- NOTE: The TV can be operated when the switch is at any position 16 [_i_t]]![.11 This is a remote control unit for multPsource and multFzone playback. Buttons ,_2)can not be used when the main unit's multi source mode is set to the REC OUT mode Buttons ,q) can only be used when the main unit's multi-source mode is set to the MULTI mode. O}The main unit's POWER (ON, OFF) buttons (2) MULTI SOURCE terminal output function control buttons (PHONO, TUNER, CD, DVD/VDP, VCR, VAUX and TAPE). (3} MULTI SOURCE terminal output level control buttons (VOLUME up and down) DEFAULT SETI ING (MULTI VOLUME LEVEL) : - - - dB (MINIMUM) (4} PRESET up and down buttons (when MULTI SOURCE function is set to TUNER). v r_ OPERATIONS Preparations: Check that all connections o _ O _ o o o o o o o o o o I are proper Set to the center position TREBLE 2 3 1 Turn power.operation switch (button). Presson thethepower _'_ _'_ 3m ON / STANDBY --3 RECEIVER ON/STANDBY When the button is pressed, the power turns on and the display lights. When pressed again, the power turns off, the standby mode is set and the display turns off Several seconds are required from the time the power switch is set to the "ON" position until sound is output. This is due to the builtdn muting circuit that prevents noise when the power switch is turned on and off Set the power operation switch to this position, the power on and off from the included remote control unit. Select the front speakers Press the SPEAKER A or B button turn the speaker on ES2:_ Set the slide switch to "AUDIO" 17 _t]1![.1][ 1 3 r%/ i Press the button for the program source to be played. EX 1: CD co cD I EX2: _o O0 TAPE TAPE MONI,OR TAPE MOHITOR 0 • Press the button once to switch the source to TAPE MONKOR input, again to cancelinput. --1 Start playback on the selected component. For operating instructions, refer to the various manuals. components' Adjust the VOLUME control VOLUb E -3 1 o _ O _ o o o o o o o o o 2 BALANCE control BJ, L^NCE reduce the volume of the right channel, clockwise to reduce the Turn the contro/ counterclockwise to volume of the left channel. o 2 34 Adjust the left/right 1 _ "O, Adjust the BASS and TREBLE control. BASS Turn the control clockwise to _ncrease the bass, counterclockwise it to decrease Turn the control clockwise to increase the treble, counterclockwise it to decrease Press the when TONEyou DEFEAT Use this do notbutton want to adjust the sound. 4 Press the LOUDNESS button. Press the loudness button ON when listening to music at a low volume. The low notes and high notes will corrected to produce a natural sound. be ,_ LOUDNESS button can be used when the TONE DEFEAT ON mode 18 _ TONE OEFEAT The Mulg-Source output terminal funcgon allows you to record a source other than the source currently • Recording a source other than the one currently playing playing or to output its signal to the MULTI SOURCE (REC OUT mode) MULT_SOURCE Press the MULTI SOURCE MODE button until "REC OUT" appears on the display D_ON o _ _:_° o o o _ I o o o =T_l_ o I 10 o o _ODE SELECT o OO _O 2 Select the source to be output to the recording output terminal. Press the MULTI SOURCE SELECT button repeatedly ungl the desired source appears on the display. 12 DISPLAY MULTISOURCE MODE EECT _ The REC OUT mode cannot be set from the remote control unit MU_T TONE SPA SP_ a 3 The selected source is indicated The signals of the source selected with the REC OUT mode are also output from the MULTI SOURCE AUDIO/VIDEO OUT terminals. ,_ To cancell the REC OUT mode. Press the MULTI SOURCE MODE "SOURCE" appears on the display button repeatedly until 19 • Playing a source other than the one currently o C_ o o o o o o o playing in a different o MULT_SOURCE Press the MULTi SOURCE MODE button repeatedly until "MULTI OUT" appears on the display i}O o room (MULTI mode) _ODE SELECT o Turn on the "MULTI" H indicator 2 3 RC-872 Select the source to be output to the MULTI SOURCE output terminal Press the MULTi SOURCE SELECT button repeatedly until the desired source appears on the display MULTI SOURCE MODE MULTI _ELECT RC-873 (RC-872) m --3 5---5 m DE_Ot4 _ c_ r,,.,,, When the MULTI SOURCE button on the RC-872 remote control unit is pressed, the MULTI mode is set directly (the "MULTi" indicator lights), and the source to be output from the MULTi SOURCE terminals can be selected When the PHONO _ TAPE buttons on the RC-873 multi source remote control unit is pressed, the MULTI mode is set directly (the "MULTI" indicator lights), and the source to be output from the MULTI SOURCE terminals can be selected directly (This cannot be selected when the mare unit is in the REC OUT mode.) oq The selected source is indicated To cancell the MULTi mode Press the MULTI SOURCE MODE button or the MULTI button on the RC-872 remote control unit repeatedly until "SOURCE" appears on the display DENON NOTE: The signals of the source selected in the MULTI mode are also output from the TAPE and VCR recording output terminals. DISPLAY STEREO....... TUN EC_ _ 2 _ ___ 4 The output level of the MULTi SOURCE AUDIO terminals can be controlled using the MULTI VOLUME • and • buttons on the RC-872 remote control unit or the VOLUME up and down buttons on the RC-873 multi source remote control unit. (RC-872) (RC-873) DEFAULT SETTING (MULTi VOLUME LEVEL): --- dB (MINIMUM) When MULTi function to TUNER, preset the channel can SOURCE be selected using is thesetPRESET • andthe• buttons on the RC873 multi source remote control unit. (This is only possible when the main unit is in the MULTI mode.) NOTE: Note that this also switches the preset reception channel on the main unit when playing or recording the tuner in the MULTI mode. 20 • Multi-source and multi-zone playback MULTI ROOM MUSIC ENTERTAINMENT SYSTEM • When the outputs of the MULTI SOURCE AUDIO/VIDEO OUT terminals are wired and connected to power amplifiers or TV displays installed in other rooms, different sources can be played in rooms other than the main room in which the this unit and the playback devices are installed. (Refer to SUB ROOM-1 on the diagram.) • When the output of the SPEAKER SYSTEM_B terminals is wired and connected to speakers in a sub room, the same source can be played in both the main room and sub room. Set the this unit's SPEAKER A/B selector according to the room in which the source is to be played. (Refer to SUB ROOM-2 on the diagram} • When a separately sold room-to-room remote control unit (DENON RC-616 or 617) is wired and connected between the main room and the sub room, the remote-controllable devices in the main room can be controlled from the sub room using the remote control unit With SUB-ROOM4 remote control unit multi-source playback, the this unit's MULTI SOURCE output can be controlled with the included RC-873 multi source Operations on the RC-873 remote control unit other than turning the multi source output volume up and down can not be performed main unit is in the REC OUT mode. _With SUB ROOM-2 remote control unit playback, the this unit and DENON CD players or tape decks etc. can be controlled when the using the included RC-872 system '_ To control playback devices other than the ones above, either use that device's remote control unit or preset a separately sold programmable remote control unit (DENON RC-770, etc.) NOTE: • Use a 75 _2/ohms coaxial pin-plug cord for video signals to connect and wire the MULTI SOURCE VIDEO output use high quality pin-plug cords and wire in such a way that there is no humming or noise. • For instructions on installation and operation of separately sold devices, refer to the devices' operating instructions MULTI ROOM MUSIC SUB ROOM-1 MAIN ENTERTAINMENT AMPLIFIRE q_/ SUB SYSTEMB I Accessoi'ies • SYSTEM REMOTE CONTROL UNIT RC 872 • MULTI SOURCE REMOTE CONTROL UNIT RC 873 Sold Separately • R RETRANSM]TTER RC 616 • R SENSOR RC 617 • PRQGRAMABLE REMOTE CONTROL UNIT RC 770 • RC872 ROOM TO-ROOM 1o4 PROGRAMABLE DRA685 4 RC616 SYSTEM CONTROL UNIT RC-872 SYSTEM REMOTE REMOTE Iseparately CONTROL sold) control MULTI SOURCE AUDIO ====== MULTI SOURCE VIDEO signal -- 175 _ / ohms) SPEAKER cable ; • ROOM-2 ,,_" CONTROL UNIT RC823 {or MULTI SOURCE REMOTE _ PROGRAMABLE REMOTE CONTROL UNIT RC 710) • SYSTEM ROOM SPEAKER For the AUDIO output, Refer to CONNECTIONS ITne s_gnal cable on pages cable 6 and 7. 21 Use this switch to monitor a video source other than the audio source. Holding the VIDEO SELECT button appears on the display. @ _ O _ o until the desired source VlOEO SELECr o o o o o o o o o m oo Set the slide switch to "AUDIO" 1 The video source switches as follows each time the button is pressed: 1- _ _© Cancelling simulcast playback. • Press the VIDEO SELECT button again • Switch the program source to the component the video. connected Use this to turn off the audio output temporarily. MUTING Press the MUTING button. Cancelling MUTING mode Press the MUTING button again -1 • Caution: Switching off the power of the unit will cancel the settings Connect the headphones to the headphones lack of the front panel _ O °T "°i 1 oo o 2 2 2-__ 22 PHONES -2 Press the SPEAKER A or B button turn the speaker off. ,_ Set the slide switch to "AUDIO". to When an operation is performed visually on the remote control unit, that operation appears on the display, making it possible to check the operation The set's operating status can also be checked on the display using the procedure described below. 1 Press the STATUS button. ,_ Set the slide switch to "AUDIO'. E_2UZ_u_l_c DENON Follow steps 1 to 3 under Simultaneous JJ Playing the program source" • The input and output sources and the setting, etc., appear in order on the display each time the button is pressed Start recording on the tape or video deck For instructions, refer to the component's instructions. operating recording The signals of the source selected with the function selector button are output simultaneously to the TAPE and VCR REC OUT jacks. If a total of two tape and/or video decks are connected and set to the recording mode, the same source can be recorded simultaneously on every decks. In addition, if the TAPE MONITOR button is pressed, the audio signals from the tape deck are output to the VCR AUDIO REC OUT jacks • Tape monitor function When a three-head tape deck is used, the sound actually being recorded can be monitored button during recording by pressing the TAPE MONITOR Press the button again to cancel monitoring. 23 [] LISTENING TO THE RADIO This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory. 2 1 ..... J! o_ o oooo i© Switch off the unit. Switch on the unit using the main unit's power operation switch while holding in the MEMORY button. The unit automatically begins searching for FM broadcast stations. ooo ON / STANDBY oo O 2 When first preset FM broadcast is found, station is stored the in the memory station at channel AI that Subsequent stations are automatically stored in order at preset channels A2 to AS, B1 to BS, C1 to C8, D1 to D8 and E1 to E8, for a maximum of 40 stations Channel A1 is tuned in after the auto preset memory operation is completed NOTES: • If an FM station cannot be preset automatically due to poor reception, use the "Manual tuning" operation to tune in the station, then preset it using the manual "Preset memory" operation. • To interrupt this function, press the power operation button. • DEFAULT VALUE AUTO TUNER PRESETS 24 A1 - A8 875/89.1/981/107.9/901/90.1/901/90.1 B1 - B8 520/600/1000/1400/1500/1710 C1 _ C8 901 MHz D1 _ D8 901 MHz E1 - E8 901 MHz MHz kHz/90 1/90.1 MHz 4123 o C_-_@,.) Set the input function to "TUNER" o o o o o TUNER o o o ©0 © Watching the display, press the BAND button tO select the desired band (AM or FM) BA_,D Press the MODE button to set the auto MODE tuning Litmode. _._ AULO °" .... R % -M F-,, B "-I,, _el- _A,F/; TUNER Press TUNING UP or DOWNthe button, • Automatic tuned in. searching bow. TUNINGu_ begins, then stops when a station is NOTE: • When in the auto tuning mode on the FM band, the "STEREO" indicator lights on the display when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the "TUNED" and "STEREO" indicators turn off Set the input function to "TUNER" Watching the display, press the BAND desired band (AM or FM). Press the MODE button to set the manual tuning mode that the display's "AUTO" indicator turns off button to select the Check Press the TUNING UP or DOWN button to tune in the desired station. The frequency in changes continuously when the button is held NOTE: • When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the "STEREO" indicator turns off. 25 _t]1![.1][ 23 4 t l Use the "Auto tuning" or "Manual tuning" operation to tune in the station to be preset in the memory == ?[![_ Press the MEMORY oo _o button MEmor_ O SHIFT Press SHIFTblock button desired the memory (A toand E). select Press the preset channel button preset channel (1 to 8). the (1 to 8) to select the desired 666_66 To preset other channels, repeat steps 1 to 4. A total of 40 broadcast stations can be preset (channels 1 to 8) in each of blocks A to E. 2 Watching the display, preset memory block. SHIFT ] D O press the SHIFT button 8 stations to select the SHIFT 1 oo O Set the slide switch to "AUDIO" 2 Watching the display, press the preset channel button (1 to 8) to select the desired preset channel. (When using the remote control unit, select the preset channel by pressing the preset channel button.) -1 -2 26 -- 8 [] INITIALIZATION OF THE MICROPROCESSOR When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the microprocessor is required by the following procedure 2 o C_:_-_::_..'_ o o o Switch out]et. o o o o Do r_ LAST FUNCTION the AC cord from the wall Hold the following TUNING UP button and TUNING button, and plug the AC cord into the outlet o o o OO off the unit and remove O Check 1that the entire display your is flashing about second, and release fingers and the microprocessor will be initialized. DOWN with the an interval from 2 buttonsof MEMORY • This unit is equipped with a last function memory which stores the input and output setting conditionsas they were immediately before the power is switched off • The unit also equipped with a back-up memory This function provides approximately one week of memory storage when the main unit's power operation switch is off and with the power cord disconnected. 27 [] TROUBLESHOOTING If a problem should arise,first check the following. 1. Are all connections correct ? 2. Have you operated the receiver according to the Operating Instructions 3. Are the speakers, turntable other components operating property ? ? If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction Disconnect the power immediately and contact your store of purchase. Symptom Cause • Power cord not plugged in securely DISPLAY not lit and sound not produced when power operat on switch set to on ._ o_ DISPLAY lit but sound not produced _ s ® _ -- PROTECT -- * Check the insertion of the power cord plug * Turn the poweE on with the remote control unit after turning the Power operat on switch on 6 17 • Connect • Improper position of the audio button • Volume control set to minimum • Set to a suitable function securely position 9,10 18 18 22 • Turn volume up to suitable level • MUTING is on • Switch • Speaker terminals are shon_circuJted • Swtch power off, connect speakers properly, then switch power back on • Turn off the set's power, the_l ve_ltilate it well to cool it down O_lCe the set is cooled down, turn the display appears • The unt is operating at continuous high power conditions and/or inadequate ventilation Cz Page • Speaker cords not securely connected • Block the vent lat on holes of the set r_ Measures off MUTING 9,10 5 power back on • Turn off the set's power, the_l ve_ltilate it well to cool it down O_lCe the set is cooled down, turn the power back on o_ (D (D Sound produced only from one channel Positions of instruments stereo playback • Connect • Connect • Reverse speakers cords • Checkleftand connectons of left and right or left and right input/output 9, 10 6 _ 8 right connectons 10 • Turntable and speaker systems too close together Floor is unstable and vibrate° easily • Separate as much as possible • Stylus pressure too weak • Apply proper stylus pressure Sound is distorted • Dust or dirt on stylus • Car[ridge defective • Check stylus • Replace cartridge Volume is weak • MC cartridge being used • Replace with MM cartridge or use a head amplifier or step-u b transformer 6 • Batteries dead • Remote control unit too far from this unit • Obstacle between this unit and remote control unit • Replace with new battedeo_ • Move closer • Remove obstacle 12 12 12 Different button is being presoed • G and O ends of battery inserted reverse • Press the proper button Insert battedeo properly 12 Howling high when record noise produced when volume is This unt does not operate properly when remote control unit is used securely 6 • Connect noise produced 6 • Connect securely • Contact your store of purchase in 6 • Use cushions to absorb speaker vibrations transmitted by floor If turntable is not equ pped with insulators, use audio insulators 28 securely securely • Ground wire of turntable not connected properly • incomplete PHONO }ack connection • TM or radio transmission antenna nearby Humming is playing ® reversed during • I_lcomplete CO_lnection of speaker cords • Incomplete connection of input/output corUs (commonly available) [] SPECIFICATIONS • Audio section (Power amplifier) Rated output: 100 W + 100 W (8 _/ohms, Output terminals: A or B 4 to 16 _/ohms A + B 8to 20 Hz - 20 kHz with 0.05 % T H.D.) 16_/ohms (Analog} LINE input -- PRE OUT Input sensitivity/input impedance: Frequency response: S/N ratio: Total harmonic distortion: Rated output: 200 mV / 47 k_/kohms 10 Hz- 50 kHz: +1 5 dB 100 dB (IHFA weighted) 0009 % (_3 dB at rated output,8 _/ohms) 12 V (1 kHz) PHONO input -- REC OUT Input sensitivity/input RIAA deviation: impedance: 30 mV/47 k_/kohms +0.5 dB (20 Hz - 20kHz) S/N ratio: 74 dB (]HF-A weighted, Total harmonic distortion: 003 % (1 kHz, 3V) Rated output/Maximum 150mV output: with 5 mV input) / 7V • Video section (standard video jacks} Input/output level and impedance: Frequency response: 1 V p-p, 75 _/ohms 5Hz_ 10 MHz +1,-3 dB • Tuner section [FM] (note: pV at 75_/ohms, 87.50 MHz _ 107.90 MHz Receiving range: Usable sensitivity: 1 4 #V(142 50 dB quieting sensitivity: SIN ratio: Total harmonic distortion: 0 dBf - 1 x 10 _' W) [AM] 520 kHz _ 1710 kHz dBf) 18 #V MONO 28 pV(202 dBf) STEREO 231iV (38.5 dBf) MONO 80 dB (IHF-A weighted) STEREO 75 dB (IHF-A weighted) MONO 015 % (lkHz) STEREO 03% (lkHz) • General AC I20V, 34 A 60 Hz Power supply: Power consumption: Maximum external dimensions: 434 (W) x 171 /H) x 416 (D) mm (17q/16" Weight: 10.0 kg (22 Ibs) • Remote control unit x 6_23/32" x 16-3/8") RC-872, RC-873 RC-872 Batteries: External dimensions: R6P/AA Type (two batteries) 54 (W) x I72 (H) x 27.2 (D) mm 100 g (Approx Weight: RC-873 (2q/8" x 6-3/4" x lq/16") 6 oz) (incLuding batteries) Batteries: External dimensions: 47.5 (W) x 127 (H) x 18 (D) mm R03/AAA Type (two batteries) Weight: 70 g (Approx. 2.4 oz) * For purposes of improvement, specifications (%27/32" x 5 x 11/16") and design are subject to change without notice 29 • INTRODUCTION Nous vous remercions d'avoir choisi le r_cepteur radio FM _AM ster6o DENON. Ce remarquable composant a 6t6 fabriqu6 pour assurer une reproduction haute fid61it_ remarquable de vos sources musicales favorites Ce produit 6rant 6quip_ d'une immense foule de caracteristiques, nous vous recommandons avant de commencer I'installation et I'utilisation de I'appareil de bien lire le contenu de ce manuel avant de proceder. TABLE DES MATIERES Avant L'utilisation ............................................................ 30 Op6rations Precautions 31 Ecouter de la Radio ................................................... Precautions D'installation ................................................ de Manipulation Caracteristiques ............................................. 31 ............................................................ 31 ............................................................ 32-36 Nomenclature et Fonctions .......................................... 36, 37 ............................................. Initialisation El 43-49 50-52 du Microprocesseur ....................................... 53 Memoire de Derni_re Fonction ....................................... 53 Depistage des Pannes Connexions Unit6 de Tel6commande El ............................................................... Specifications ................................................... 54 ............................................................... 55 38-43 • ACCESSOIRES Verifier que les articles suivants sont inclus darts le carton en plus de I'unite principale: 0) (2) (3) (4) Mode d'emploi ............................................................ Certificat de garantie ...................................................... Liste des centres d'entretien .......................................... T616commande (RC-872) ................................................ (RC-873} ................................................ 1 1 1 1 1 @ ® %% (RC_872) [] AVANT (RC_873) ......................................................... 2 (R03/AAA) ...................................................... (6} Antenne_cadre AM ......................................................... (7} Antenne interieure FM ................................................... ® © 2 1 1 ® L'UTILISATION Faire attention au points suivants avant d'utiliser • D_placement del'appareil cet appareil: • Ranger ces instructions Pour 6viter des court-circuits ou des fils endommages dans les c_bles de connexion, toujours debrancher le cordon d'alimentation, et d_connecter les c_bles de connexion entre tous les autres composants audio Iors du d6placement de I'appareil. • Avant de mettre sous tension V6rifier une nouvelle fois si toutes les connexions sont bonnes et s'il n'y a pas de probl_mes avec les c_bles de connexion. Toujours placer I'interrupteur de raise sous tension en position d'attente avant de connecter et de deconnecter les c_bles de connexion. 30 (5) Piles (R6P/AA) dans un endroit s_r Apr_s les avoir lues, ranger ces instructions la garantie darts un endroit s0r. en m6me temps que • Noter que les illustrations de ces instructions de I'appareil actuel dans un but d'explication. peuvent varier [] PRECAUTIONS L'utilisation electroniques ///////////////////////////////////////////////,, D'INSTALLATION N 10 cm ou plus simultan6e de cet appareil ou d'autres appareils _ m_croprocesseur avec un tuner ou un t_16viseur peut produire des parasites dans le son ou I'image Si cela se produit, prendre les mesures suivantes: • Installer cet appareil aussi loin que possible t_16viseur. du tuner ou du * OO (3 I "//////////////////////////////////////////////, • E]oigner les cables d'antenne du tuner ou du t616viseur aussi loin que possible du cordon d'alimentation et des c_bles de connexion d'entr6e/sortie de cet appareil • Ce probl_me est fr6quemment rencontre lots de I'utilisation d'antennes int6rieures ou de cSbles d'arriv6e de 300 _/ohms. L'utilisation d'antennes exterieures et de c_bles coaxiaux de 75 _2/ohms ....... 10 cm ou plus est recommandee. Pour permettre la dissipation de la chaleur, laisser un espace d'au moins 10 cm entre le haut, I'arri_re et les flancs de cet appareil et le mur ou d'autres composants. Mu[ //////////////////////////////////// [] PRECAUTIONS DE MANIPULATION • Commutation de la fonction d'entr_e d'entr_e ne sont pas connectees Iorsque les prises Un d_clic peut 6tre produit si la fonction d'entr6e est commutee Iorsque den n'est connect6 aux prises d'entr6e Dans ce cas, abaisser la commende VOLUME ou connecter des composants aux prises d'entr_e • Mise en sourdine des prises de sortie pr_amplifiee • Chaque fois que I'interrupteur de mise sous tension est en position STANDBY, I'appareil est toujours connecte _ une tension de ligne secteur. Toujours debrancher le c&ble pour aller, par exemple, en vacances. (PRE OUT) Les prises de sortie preamplifiee (PRE OUT) comprennent un circuit de raise en sourdine. Pour cette raison, les signaux de sortie sont fortement r6duits pendant plusieurs secondes apr_s que I'interrupteur de m_se sous tension air 6t6 allure6 Si le volume est augment6 pendant cet instant, la sortie sera tr_s _lev6e apr_s I'arr6t du circuit de raise en sourdine Toujours attendre que le circuit de mise en sourdine se desactive avant de r6gler le volume r-_ 1. CARACTERISTIQUES Systbme d'equipement sonore dans plusieurs pibces (Multi Room Music Entertainment System Fonction avec des sources multiples : La fonction muIti_source de I'appareil vous permet de selectionner diff6rentes sources audio et vid6o pour ]'ecoute ou le visionnage, afin d'en profiter dans la salle principale et dans une autre pi#ce au m6me moment. Cette nouvelle option vous procure une souplesse d'utilisation in6galCe, une fois que votre syst_me a et_ installe avec cet appareil Le niveau de sortie, r_glable par t_l_commande, est equivalent _ IV, ce qui est assez pour activer un amplificateur additionnel install_ dans une autre piece 2. Amplificateur puissant et modulable Amplificateur de puissance de tr_s haute qualite: Une grande vitesse et des transistors a haute pu=ssance sont utilis_s dans la configuration du circuit rationnel, ce qui t_moigne de I'avance technologique de DENON en mati_re d'amplificateurs, et garantit une sortie du son aussi claire que pu=ssante 3, Architecture individualisee Construction - SLDC} des signaux (Signal Level Divided Les circuits fournissant les signaux de bas et haut niveau ont et_ separ_s dans des blocs diff_rents, afin de maintenir I'influence des signaux les uns sur les autres a I'absolu minimum.La conception du chassis de cet appareil est appel¢ Architecture individualis_e des signaux (Signal Level Divided Construction SLDC). Les s_gnaux en sortie sont plus puts qu'auparavant, ce qui permet une reproduction des sons encore plus claire et fid_le 4, Fonctions de la t_lecommande • Tel_commande avec fonction de pr_-m_morisation (RC-872) : Cet appareil est equip_ d'une t_l_commande dotee de la fonction de pr_=m_morisation. Les codes de contr61e distance pour tousles composants DENON contrdlables distance, tels que les lecteurs DVD, lecteur video, t_l_vision ..etc ainsi que ceux fabdques par d'autres producteurs =mportants sont d_j_ en memoire • Tel_commande du mode B sources multiples (RC=873) : Cet appareil est _quipe d'une t_lecommande dot_e du mode sources multiples, qui commande les sorties des sources multiples et commande _galement le r_cepteur pour choisir les fonctions, trouver des stations pr_=r_gl_es, ou alors ajuster le niveau du volume depuis une autre piece 31 [] CONNEXIONS • Ne pas brancher le cordon d'alimentation toutes ]es connexions. • Remarquer que ]e groupement de cordons a fiches a broche avec des cordons d'alimentation, ou le fait de los placer pros d'un transformateur provoque un bourdonnement ou un autre bruit. • Un bruit ou un bourdonnement peat _tre g_n6re si un composant audio connect_ est utiBe ind6pendamment sans mettre cot appareil seas tension Dans ce cas, mettre cot apparefl seas tension • Des parasites ou des bourdonnements peuvent se produire si un des composants est utflis6 de matiere autonome sans que cot apparefl ne soit allum6. Si cola se produit, allumez cet appareil avant d'avoir terrain6 • Toujours connecter correctement les canaux de gauche et de droite (gauche avec la gauche et droite avec la droite). • Inserer refinement les fiches Des connexions incompl_tes peuvent gen6rer des parasites. • N'utiliser les prises seeteur (AC OUTLETS} que pour I'equipement audio. Ne pas los utiliser pour un sechecheveux, etc. ObT#UT Platine tourne-disque (celMe a bobine mobile MM) L Lecteur de CD -- -[:3 oo REMARQUE: I Connexion _ _ E]E]E]C] o==0 _ Cot appareil ne peat pas 6tre ut lise d rectement avec los cellules a bobine O mobile (MC) Utiliser un ampl ficateur de t6te separ6 ou un transformateur survolteur appareil en utilisant los cordons a fiches a broche (PRE OUT} t sortie preamplifiee Prises de entree principale (MAIN IN) Utiliser cos prises ]ors de ]'utilisation d'un pre-amplificateur principal ou d'un arnplificateur s@pare Fil de raise a la torte LINE d'un lecteur de CD I Connecter los prises de sortie analogique (ANALOG OUTPUT( da lecteur de CD aax pnses CD de cot ECordond'alimentation 120VCA60 Hz OUT AUXOUT LINE IN RC-616 (Vendue s6parement) RE-EMETTEUR INFRAROUGE LINE IN RC-617 (Vendue separ6ment) DETECTEUR INFRAROUGE DENON Plat ne cassette [] OUTPUT Amplificateur [ Connexion d'une platine cassette ] Connexions pour I'enregistrement: Connecter los prises d'entree d'enreg strement {LINE IN ou REC) de ia platine cassette aux prises de sortie (OUT) d'enregistrement de cassette de cot apparel en utilisant los cordons fiches a broche INPUT de puissance - 1 [ Connexion des gi'ises salaMi' } PRISES SECTEUR Connexions pour la • le6ture_ Connecter los prises de sortie de lecture (LINE OUT ou PB) de la plat ne cassette aux prises d'entree (IN) de lecture de cassette de cot appareil broche en utilisant los cordons a fiches Prises commutees (SWITCH ED( (capacite totale 120 W (1A )) L'alimentation de ces prises est activee et desactivee par I'interrupteur de raise sous tension (POWER) situe sur I'unit@ principale Ces prises sent egalement commutees Iorsque I'alimentation est raise en veille /ON-STANDBY( a I'aide de la telecommande Aucune alimentation electrique n'est fournie par ces prises quand Falimentation de I'appareil est en mode d'attente (standby) Ne iamais connecter d'equipement dent la capacit@ totale est supedeure a 120 W (1 A) REMARQUE: N'utiliser los prises secteur (AC OUTLETS( que pour I'equipement utiliser pour un s6che-cheveux, etc 32 audio Ne pas los ] • Pour connecter le signal video, connecter une baisse de la qualit6 du son • Lors des connexions, en utilisant se reporter 6galement un cable de signal vid6o de 75 _2/ohms aux instructions d'utilisation I Connexion d'un televiseur/tuner T616viseur ou tuner DBS k OUT o V,DEa 111 5 © © L'utiJisation d'un mauvais cSble peut entratner des autres composants DBS I T616viseur/DBS • Connecter la prise de sortie video (VIDEO OUTPUT) du t@16viseur ou du tuner DBS a la prise d'entree de televiseudtuner DBS (TV/DBS IN) _ (}aune) en utilisant un cordon a fiches a broche coaxial video de 75 _dohms • Connecter la prise de sortie audio (AUDIO OUTPUT) du t@16viseur ou du tuner DBS a la prise d'entree de tel6viseur/tuner DBS (TV/DBS IN) _ en utilisant des cordons a fiches a broche Prise de sortie de moniteur (MONITOR OUT) • Connecter la prise d'entree vid@o (VIDEO INPUT) du tel6viseur a la prise de sortie de moniteur (MONITOR OUT) en utilisant un cordon a fiches broche coaxial video de 75 _/ohms Moniteur de televiseur Lecteur de LD (VDP) ou lecteur de DVD L OU N ...... o_L_! I Connexion 5 © © .... _Z F_ -- N d'un lecteur de video disque (VDP) ou d'un lecteur de DVD I • Connecter la prise de sortie video (VIDEO OUTPUT) du lecteur de video dsque (lecteur de DVD) a la prise d'entr@e de DVD/VDP (DVD/VDP IN} _ (}aune) en utilisant un cordon fiches a broche coaxial video de 75 £!/ohms • Connecter la prise de sortie audio analogque (ANALOG AUDIO OUTPUT) du lecteur video disque {lecteur de DVB la prise d'entree de DVD/VDP {DVD/VDP IN) _ ut ]isant des cordons a fiches a broche de en [ Connexion des magnetoscopes ] Connexions d'entree/sortie video: • COn_lecte_ la prise de sortie vid@o (VIDEO OUT) du magn@toscope la prse d'entree de magnetoscope (VCR IN) [_ 0aune} et la prise d'entree video (VIDEO IN) du magnetoscope a la prise de sortie de magn@toscope (VCR OUT) _ (iaune) en utilisant les cordons fiches a broche coaxial video de 75 £_Juhms Connexion des prises de sortie audio • Connecte_ les prises de sorde audio (AUDIO OUT) du magnetoscope aux prises d'entree de magnetoscope (VCR IN) _ et les pr4ses d'entree audio (AUDIO IN) du magnetoscope aux prises de sortie de magnetoscope (VCR OUT) _ en utilisant des cordons a fiches broche 33 (Accessoire) ANTENN E-CADRE AM DIRECTION DE STATION DE RADIODIFFUSION f ANTENNE FM _@@ ..... _, @@ o ......... @ CABLE COAXIAL DE 75_ohms z:_o,, ..... @ @..... _s,_s @ @@, ............ @@1@@,,_, _ ANTENNE EXTERIEURE AM ® ///_ //// TERRE Antenne interieure FM (Accessoirel fEnsemble d'antenne-cadre Connexion AM C©nnecte_ 1 Desserrer bo_r_e i_ _ des antennes AM aL/X drante_7ne Plier dans la ligne de connexion direction 2 Ins@re_ le co;don dans le sens contraire des aiguilles d'une montre AM Defaire le noeud en vinyle et sorur la @n tournsnt 3 Serr@[ en tourns_lt dans le sens des aiguilles d'une montre inverse a Avec I'anterlne sur le haut de toute Remarque _ rinstallateur de syst_me de t616distribution: Ce rappel est fourni pour a_irer Kattention de I'installateur de systerne de teledistnbution sur Karticle 820-40 du NEC qui foumit des directives sur une bonne raise a la masse et, en particulier, specifie que la terre du c_ble doit 6tre connectee au systeme de mise a la masse du bat ment, aussi prBs du point d'entree de c&ble que possible surface stable Monter Flemai'ques: • Ne pas connecter simdtanemeRt • M@me si une antenne exterieure I'antenne-cadre AM Trou d'installation _, 34 Monter au tour, etc J deux 8RtenRes FM AM est utilisee, ne pas deconnecter • Verifier que les bornes de fil d'antenne-cadre pardes metalliques du banneau AM ne touchent pas les • Connecter les bornes d'enceinte aux enceintes en respectant les polarit6s (_ au @, e au G). Si les polarit6s ne sont pas Impedance d'enceinte • Lorsque des syst_mes respect6es, un son central faible est entendu, I'orientation des divers instruments n'est pas correcte et le sens de la direction du son st6r_o est d6t_rior6 • Lors de la r_alisadon des connexions, prendre soin de ne mettre en contact aucun des conducteurs individuels du cordon les enceintes ayant une impedance de 4 a 16 _I/ohms peuvent 6tre connectees pour une utilisation comme enceintes. • Faites attention en cas d'utilisation de 2 paires d'enceintes (A+B) en m6me temps, puisque il faut utiliser des enceintes avec des imp6dances entre 8 et 16 _2/ohms. • Le circuit de protection peut 6tre active si le syst_me est reproduit pendant une Iongue dur6e a un volume _lev6 Iorsque des encemtes d'une imp6dance inf6rieure a ceile specifi6e sont connect6es d'enceinte avec des bomes adjacentes, avec des conducteurs d'autres cordons d'enceinte ou avec le panneau arri_re REMARQUE: d'enceinte A et B sont utilises separ6ment, NE JAMAIS toucher les bornes d'enceinte Iorsque I'ampli est sous tension, sinon des decharges electriques risquent de se produire. Connexion des bornes d'enceinte 1 Tourner daRs contraire des d'unemontre I@ s@ns 2 Insererle cordon aiguilles pour Connexion 3 TotJ[rl@r des fiches bananes daRS le seas des aiguillesd'une la desserrer Fnont[e pou[ 18 resserre_ Toumer dans le sens des aiguilles d'une montre pour serrer, puis inserer lafiche banane [ SYSTEME D'ENCEINTES ] [ SYSTEME D'ENCEINTES1 Systeme B Systeme A • Precautions a prendre Iors de la connexion des enceintes Si une enceinte est placee pres d'un televiseur ou d'un rnoniteur video, les couleurs de I'ecran peuvent _tre perturbees par le magnetisme de I'enceinte Si ce]a se produt, deplacer I'enceinte vers un endroit oQ cet effet ne se produit pas m m 35 ,, Cet appareil est dote d'un circuit de protection _ haute vitesse. Ce circuit protege les circuits internes de tout endommagement eventuel dO a I'afflux de courants importants Iorsque les prises d'enceinte ne sont pas completement connectees ou Iorsqu'une sortie est g6ner6e par un court-circuit. Darts un tel cas, le circuit de protection fonctionne pour couper la sortie aux enceintes. Si cela se produit, eteindre I'appareil et verifier les connexions d'enceinte. Ensuite, mettre a nouveau I'appareil sous tension. Apres un silence de quelques secondes, le recepteur devrait fonctionner normalement. Si le circuit de protection est a nouveau active bien qu'[I n'y ait pas de probleme de c_blage ou de ventilation autour de I'appareil, couper I'alimentation, et contacter un centre d'entretien DENON. • [] Le circuit de protection peut 6tre active sl I'appareil est utilise pendant une Iongue duree _ un volume 61eve Iorsque des enceintes d'une impedance inf6rleure a celle specifiee (par exemple, enceintes ayant une impedance inferieure _ 4 _2/ohms) sont connectees. SI le circuit de protection est active, la sortie des enceintes est coupee. Couper I'alimentation de I'appareil, attendre qu'il refroidisse, ameliorer la ventilation autour de lui, puis remettre sous tension. NOMENCLATURE ET FONCTIONS • Pour les details sur les fonctions de ces pi6ces, se reporter aux pages donn6es entre parentheses T 0 ................. £ I Ft_ .........................,._._._ ( ) I[_2. _ONHz Multi Room _._ _.¢.9._.._@._.@. _o._._ ) _]_ Interrupteur de mise en marche Prise de casque d'_coute (PHONES) _) Commande _) Commande VOLUME (_ Touches de selection Touche VIDEO SELECT ................................................ (48) _) Atfichage (45, 46) (_ T_moin d'alimentation ....................................... ................................................ (44) (44) _) Commande de r_glage de graves (BASS) (44) _]_ Touches de selection ........................ .................. (44) TouchesTUNING (44) ................................................... de m_moire pr_r@glee (44) ............... ................................................... Capteur de tel@commande (REMOTE SENSOR) Touche LOUDNESS ...................................................... Commande de r6glage des aigus (TREBLE) ,) BALANCE ................................................... (43) Touche TONE DEFECT .............................. (43) (48) Touches MULTI SOURCE 36 .................................... ................................................ Touches SPEAKER A!B _) 0 de source d'entr6e (43) ............... ................................................... ........................ (B2) (38) (B1, 52) (44) Fa'J:!'_[I,]_[,..'] • Pour les details sur les fonctions de ces pi6ces, se reporter aux pages donn6es entre parentheses ( ) I CD MD/CDI SElecteurde TV VCR DVD VDP CD DVD/VDP_ .................. t Touches POWER ..................... VCR ....................... (44) VAUX I I::Z} I:Z_ (:Z)i I:Z3 TUNER _40N TOR I Touches MULTi SOURCE (42, 43) I I S'_;etCteeeJt ? !1 ?°utt: MULTI (39, 40) I | I PHONO mode :%1:1:0:1';,:':°? d:.................. ,E2/ I C_ ...._... , ......... {45, 46) t MULTI VOL " CHANN£[ -- /_chK:vdct#Yt'?:t .................. ,3_, 42, t t/_:V;,_t_:%%P/ ......... /38,42/ _1 Touche SPEAKER B...................... 143/I I Touche SPEAKER A ........................ (43) I SETUR MENU , i , i JVOLUMEI I t I C_ CD C_ L...._..J ToLCh MSEd: c° m rr:a n !: .................... {44) SELECT _ I Touche VIDEO SELECT .................. (48) I I Touches de systeme (TV) (42) ............... MUTING Lt I Touche MUTING ........................... {48) I Touche STATUS ........................... {49} I E CONTROL UNIT R_C-872 _, L_T DENON REMARQUE: • Les touches rayees _ ne fonctionnent pas avec le cet appareil (Rien ne se passe Iorsqu'elles sont enfonc6es ) 37 [] UNITE DE TELECOMMANDE En suivant la procedure expliquee ci-dessous, inserer les piles avant d'utiliser la t_lecommande, Diriger la t616commande vers le detecteur de t616commande mani#re indiqu6e sur le diagramme de gauche. de la REMARQUES: • La t616commande peut _tre utilisee & une distance dbecte d'environ 7 m, mais cette distance diminue ou le fonctionnement devient difficile sql y a des obstacles entre la t6]_commande et le detecteur de t61_commande, si le detecteur de t61_commande est expos_ & ]a lumi_re directe du soleil ou a une autre lumi_re forte, ou s[ e]le est actionn6e d'un angle • Des enseignes au neon ou autres dispositifs emettant des parasites type impulsion a proximit6 peuvent entrafner un mauva_s fonctionnement, par cons6quent garder I'appareil aussi loin que possible de ces dispositifs. Approx 7 m/23 p[eds _ Pour t_lecommande (R0-872) lj Appuyer de la man,ere _nd_quee par la fl#che, et retirer en glissant. Pour t_lecommande multi-source ,:.2_InsUrer correctement les piles R6P/AA de la mani_re indiqu6e sur le diagramme (3) Refermer le couvercle ,_2_Ins_rer correctement les piles R03/AAA de la mani_re indiquee sur le diagramme (3) Close the lid. (RC-873) lj Appuyer de la manlere _ndlquee par la fl#che, et retirer en glissant, REMARQUES: • V_rifier que les polarites sont correctes. (Voir I'illustration _ I'intSrieur du compartiment a piles) • Retirer les piles si I'_metteur de la t_lecommande n'est pas utilis_ pendant une Iongue p_riode • Si des piles fuient, les jeter imm_diatement. Eviter de toucher le mat_del fuyant ou de le laisser entrer en contact avec un v_tement, Nettoyer _ fond le compartiment a piles avant de mettre de nouvelles piles en place • MSme si moins d'un an s'est 8coule, remplacer les piles par des neuves si I'appareil ne fonctionne pas Iorsque I'unit_ de t_l_commande actionn_e 8 proximitY. (La pile fournie ne sert que pour la v_rification du fonctionnement. La remplacer par une neuve le plus t6t possible.) • Au moment du remplacement des piles, apr#s les avoir retire, attendre environ une minute avant d'en insurer de nouvelles 38 etc. est Les composants audio t616commandables DENON peuvent 6tre contr616s en util[sant la t616commande de cet appareil. Cependant, remarquer que certains composants ne peuvent pas 6tre actionn6s avec cette t_16commande --1 R6gler le commutateur coulissant vers la position composant a actionner (CD ou MD/CD_R). du CD MD/CD-R -2-C Utiliser touches pour actionner le composant Pour lesles d6tails, se indiqu_es reporter aucFdessous mode d'emploi du composant respectif. audio. 2-5-- a. Pour lecteur CD et MD/CD-R 44,_1_ • : Recherche manuelle (en arri@re et en avant) : Arr6t : Lecture 1_141,1=,_-I: Recherche automatique II : Pause DISC SKIP+ : S61ection de disque (Uniquement changeur de CD) b. Pour platine cassette (DECK) 44 _l,_ • I_ _1 DBC $KI#4 : : : : : En ArtiSte En Avant Arr6t Lecture en avant Lecture en arri_re c, Pour TUNER SHIFT : Changer la plage de canaux prer6gl6s CHANNEL : Augmentation/diminution + ,de canal pr6r_gl6 REMARQUES: • La platine cassette "AUDIO" Les composants (DECK) et TUNER peut 6tre util[s6e Iorsque le commutateur est sur la position DENQN peuvent 6tre actionn6s en reglant la m6moire pr6-r6gl6e sur MD ou CD-R. --1 Regler le commutateur coulissant vers "MD/CD=R". CD MD/CD-R Tout en maintenant enfonce le bouton de lecture (PLAY), appuyer sur le bouton du composant que vous souhaitez r_gler (Se reporter au tableau 1.) Tableau 1: Combinaisons des codes de m systeme personnels VOLUME PLAY (1_) -2 MD VOLUME CD_R REMARQUES: • La m_moire ne peut @tre pr@r_gl@eque pour le MD ou le CD-R. _ Codes pr@r@glesregl@s a la livraison de I'usine et Iorsque r@initialis@s DENON 39 DENON et d'autres fabricants de composants peuvent 6tre actionn6s L'op_ration n'est pas possible pour certains modeles. --I -2,3 -A 2 en r6glant la memoire Regler le commutateur coulissant vers "VIDEO" Tout en maintenant enfonc6 le touche pr_r6gl6e de votre fabdcant de composant CD POWER vid6o. MD/CD-R du composant (DVD/VDP. VCR ou TV) que vous voulez mettre en place, appuyer sur la touche du fabriquant correspondant dans le bloc A. (Se reporter au tableau 2) A present, tout en maintenant la touche POWER (a]imentation) enfonc_e, appuyer sur la touche du code darts le bloc B. (Se reporter au tableau 2} Pour continuer I'enregistrement d'autres composants, r6p6ter les 6tapes 2 a 3 Cette t616commande peut 6tre utilisee pour actionner des composants d'autres fabncants sans utiliser la fonction enregistrant le nom du fabdcant du composant de la mani_re indiqu6e de la mani_re indiquee dans le tableau 2. de programmation Tableau 2: Combinaisons des codes de systeme personnels pour differents fabricants "DVD" "VDP" MASTER VOL MASTER VOL MUTING A _ MASTERVOL [_ MASTER DVD/VDP MULTi MUTING } DVD/VDP DENON A DENON B -- A (_ DENON B DENON C MULTI VCR VCR MITUBISHI -- -- MULTi VOL • MULTI VOL • PANASONIC -- -- TAPE MONITOR PANASONIC -- -- TAPE MONITOR TUNER TUNER SONY -- -- SHIFT SHIFT PIONEER -- -- MULTi VOL • MULTI VOL • TAPE SONY -- -- TAPE TAPE PIONEER -- -- TAPE TUNER _-_ TOSHIBA -- -- TUNER [_ } TAPE TAPE PHILIPS -- -- TAPE TAPE RCA -- -- MAGNAVOX -- -- TAPE @ TUNER _ TAPE TUNER REMARQUES: • La memoire ne peut @tre pr6r@gl6e que pour le DVD ou le VDP. _ Codes prer6gles r@gl6s a la livraison de I'usine et Iorsque r6initialis6s. 40 DENON VOL _ en Fa'_'_ [I,]_.[,..'] "VCR" "TV" MASTER VOL B A _ MASTER VOL MUTING MUTING MASTER VOL MASTER VOL DVD/VDP DVDpdDP MULTi HITACHI A HITACHI B VCR MITUBISHI A MITUBISHI MULTi VOL • PANASONIC A PANASONIC MULTI VOL • PANASONIC TAPE MONITOR JVC (VICTOR) A JVC (VICTOR) B JVC (VICTOR) C TAPE MONITOR JVC (VICTOR) -- -- TUNER SONY A SONY B SONY C SHIFT PIONEER MULTi VOL • TOSHIBA TAPE SANYO TAPE SHARP A SHARP B TUNER _-_ NEC A NEC B NEC C TAPE [[_ PHLIPS B A TOSHIBA A SANYO PHILIPS B RCA B TAPE GENERAL ELECTRIC A GENERAL ELECTRIC _ A C C MAGNAVOX MITUBISHI -A A MITUBISHI -B PANASONIC B TUNER SONY -- -- SHIFT PIONEER -- -- MULTI VOL • TOSHIBA -- -- -- TAPE SANYO -- -- -- TAPE SHARP -- -- TUNER _-_ NEC -- -- C TAPE [[_ PHILIPS -- -- -- TAPE RCA -- -- TAPE GENERAL ELECTRIC A B B HITACHI VCR -B RCA A MAGNAVOX PANASONIC B PHILIPS A (_ B -- TAPE TUNER MITUBISHI MULTI MAGNAVOX C TUNER (_ MAGNAVOX GENERAL ELECTRIC B -- __ -- Codes prer6gles r0gl6s B la livraison de I'usine et Iorsque r6initialis6s. REMARQUES: • Les signaux des touches enfonc6es sont emis pendant le rOglage de la mOmoire pr6rOgl6e Pour Oviter une op6ration accidentelle, recouvrir la fen@tre d'6mission de la t616commande pendant le rOglage de la memoire pr6r6glOe • Certains mod@les et annOes de fabrication de composants des fabricants enum6r6s dans le tableau 2 ne peuvent pas @tre utilises. • L'appareil est pourvu de diffOrents types de codes de t6lOcommandes, lesquels varient en fonction du constructeur. Si la tOl6commande ne fonctionne pas Iorsque le r6glage est fait sur A, r6gler sur B ou C et essayer B nouveau 41 I Placer le commutateur "VIDEO". coufissant sur la position CD MD/CD-R AUOIOI_ VIDEO --1 --2 Actionner composant video aux instructions d'udfisation du composant. • Pour lesle d_tails, se reporter •_ Certains modeles ne peuvent pas 6tre actionn6s avec cette unit_ de t616commande a. Pour lecteur DVD POWER • I_ -2-C : Mise sous/hors tension : Arr6t : Lecture 1_1_1,_ n : Recherche automatique : Pause (rep_rage) TITLE MENU DISPLAY SET UP RETURN : : : : : Appeler le titre Appeler le menu Changer I'affichage Installation de DVD Retour de menu •, • _1, I_ SELECT DISC SKIP + : : : : Curseur vers le haut/bas Curseur vers la gauche/droite Entrer le r6giage S61ection du disque REMARQUE: Certains fabricants udlisent des noms diff6rents pour les touches de commande de DVD, doric se reporter egalement aux instructions b. Pour lecteur de videodisque (VDP) de t_l_commande de ce composant c. Pour platine video (VCR) d. Pour televiseur O^Q^O °o o0 @"0"% POWER : Mise sous/hors tension _1_1,1_1_ : Recherche manuelle (en arriere et en avant) • : Arr_t I_ : Lecture POWER : Mise sous/hors tension _1_1,1_1 '_ : Recherche manuelle (en arr@re et en avant) • : Arr_t I_ : Lecture VOLUME : Augmentation/baisse •, • de volume CHANNEL: Changer le canal I_l_l,ll_Jl_l CHANNEL : Changer le canal +, - REMARQUE: II 42 : Recherche automatique (rep_rage) : Pause POWER + : Mise sous/hors tension ,- La television peut _tre utilis_e quelle que soit la position du commutateur. Cette t_16commande est une t61_commande pour ]a lecture multFsource ou multi zone. Les touches {2_ne peuvent pas 6tre utilis6es Iorsque le mode multFsource de I'unit6 pdncipale est r6gl6 en mode REC OUT (sortie d'enregistrement) Les touches (4_ peuvent 6tre utilis6es seulement en mode MULTI. Iorsque le mode multFsource de I'unite principale est r_gl6 rh© O_Touches d'alimentation ON/OFF (POWER) de I'appareil principal. (2)Touches de commande de fonction de sortie de la borne MULTI SOURCE (PHONO, TUNER, CD, DVD/VDP, VCR, V.AUX et TAPE (cassette) (3)Touches de commande de niveau de sortie de la borne MULTI SOURCE (augmentation et diminution de VOLUME). REGLAGE PAR DEFAUT (MULTI VOLUME LEVEL) : - - - dB (MINIMUM) (4_Touches PRESET (pr6r_glage Haut et Bas) (lorsque la fonction MULTI SOURCE est regl6e sur TUNER). v [] OPERATIONS Preparatifs: V6r[fier que toutes les connexions o 2 _ O _ o o 3 o o o o o o o 1 o sont bonnes R_gler a la position centrale. TREBLE 1 Allumer Appuyer I'alimentation. I'interrupteur de raise en marche (touche). ON / STANDBY RECEIVER ON/STANDBY Lorsqu'on appuie sur la touche, I'alimentation s'allume et I'affichage s'eclaire Lorsqu'on appuie encore, I'alimentation s'eteint, le mode de veille est mis et I'affichage s'@teint. Plusieurs secondes sont n@cessaires _ partir du moment oO I'interrupteur d'alimentation est r@gl_ sur la position "ON" avant que le son soit _mis. Ceci est dO au circuit de mise en sourdine qui evite le bruit Iors de la mise sous et hors tension R@gler I'interrupteur POWER sur cette position pour mettre I'appareil sous et hors tension a I'aide de la t@lecommende foumie (RC-872) S@lectionner enceintes avant.d'enceinte Appuyer sur les le commutateur I'enceinte A ou B pour activer ME_ _ ,_ R_gler le commutateur coulissant vers "AUDIO". 43 i _1 :_.__ [_]_. -] 1 3 r%/ i Appuyer sur la touche de la source de programme EX 1: CD co cu B reproduire I L_.f_........... EX 2: TAPE {_o O0 TAPE MONI,OR TAPE MO_qlTOR 0 • Appuyer une nouvele lois sur la touche pour changer la source I'entr6e TAPE MONITOR, 8 nouveau pour annulet I'entree --1 2 Commencer la lecture sur le composant s61ectionn6. Pour les instructions d'ut/isation, se reporter aux manuels des divers composants 3 Ajuster la commande VOLU_ VOLUME. E V_ -3 1 0 _ 0 _ 0 0 0 0 0 0 0 34 0 0 2 Regler la commande BALANCE (6qulibre) avant gauche/droite. inverse des aiguilles d'une montre pour volume du canaldansle droit, dans Tr_duire our netle la commande sensle sens des aiguilles d'une montre pour augmenter le volume du canal gauche 0 1 2 Ajuster le commande BASS © BJ, L*,C= _. "O. _ BASS (graves) et le TREBLE (aigu6s). Tourner la commande dans le sens des aiguiles d'une montre pour augmenter les graves, dans le sens inverse des aiguilles d'une montre pour les r@duire Tourner la commande dans le sens des aiguilles d'une montre pour augmenter les aigu_s, darts le sens inverse des aiguilles d'une montre pour les r@duire 3 4 Appuyer sur la touche TONE (d@sactivation). Utiliser cette touche Iorsque voulez pas regler le son. DEFEAT vous TONE OEFEAT ne Appuyer sur la touche LOUDNESS (compensation physiologique). Appuyer sur le touche de compensation physiologique lots de I'_coute de la musique a un niveau de volume bas Les notes basses et aigu_s sont corrigees afin de produire un son naturel Le touche LOUDNESS (compensation physiologique) @tre utlis@ quand le mode TONE DEFEAT ON 44 peut F_ La fonction de source multiple vous permet d'enregistrer borne de sortie de source multiple une source autre que la source actuellement reproduite [l_,[.'] ou de sortir son signal vers la • Enregistrement d'une source autre que celle en cours de lecture (mode REC OUT (sortie d'enregistrement)) 1 D_ON Appuyer sur la touche MULTI SOURCE MODE jusqu'_ ce que "REC MULT_SOURCE _ODE SELECT OUT" (sortie d'enregistrement) apparaisse sur I'affichage o _ Do o o o o == o o [_] o o o o OO 2 12 S_lectionner la source _ envoyer la borne de sortie d'enregistrement. Appuyer rep6titivement sur la (selectionner jusqu'a touche MULTImulti-source) SOURCE SELECT ce que la source d6sir6e apparaisse MULTISOURCE MODE EECT _ _[_ --. sur l'afflchage DISPLAY Le mode REC OUT (sortie d'enregistrement) 6tre r6g16 a partir de la t616commande. MU_T TONE SPA SP_ a 3 ne peut pas La source s61ectionn_e est indiqu6e •_ Les signaux de la source s61ectionn6e avec le mode REC OUT (sortie d'enregistrement) sont egalement envoy6es partir des bornes MULTI SOURCE AUDIO/VDEO OUT (sortie audio/vid6o multi_source) Pour annulet le mode REC OUT. Appuyer sur la touche MULTI SOURCE MODE jusqu'a ce que "SOURCE" apparaisse sur Yaffichage. 45 • Lecture d'une source autre que celle en cours de lecture dans une autre piece (MULTI) mode 3 o c=_ c=_ 0 C_ o o o o o o o o o S_lectionner ]a source a envoyer & la borne de sortie MULTI SOURCE Appuyer r_p6titivement sur la touche MULTI SOURCE SELECT (selectionner multi-source), jusqu'a ce que la source d6sir6e apparaisse sur ]'affichage o MULTI SOURCE MULTI (RC-872) 13 RC-872 RC-873 _ --3 ,_ Lorsque la touche MULTI de la t_l_commande est enfonc_e, le mode MULTI est r_gl_ directement (Kindicateur "MULTI" s'allume), et la source a envoyer a partir des bomes MULTI SOURCE peut _tre s_lectionn_e Lorsque les touches PHONO -- TAPE (cassette) de la t_lecommande multi-source RC-873 est enfonc_e, le mode MULTI est r_gl_ directement (l'indicateur "MULTI" s'aflume), et la source & envoyer a partir des bornes MULTi SOURCE peut _tre selectionn_e directement (Ce mode ne peut pas _tre selectionn_ Iorsque I'unite pdncipale est en mode de REC OUT) 5---5 _ DE_Ot4 .,.,,, L _J_ La source s_lectionn_e est indiqu_e Pour annulet le mode MULTI. Appuyer sur la touche MULTI SOURCE MODE ou appuyer rep_titivement sur la touche MULTI de la t#lecommande RC-872 jusqu'a ce que "SOURCE" apparaisse sur I'affichage. REMARQUE: Les signaux de Is source s_lectionn_e en mode MULTI sont egalement envoy_s des bornes de sortie d'enregistrement TAPE (cassette) et VCR (magnetoscope) DENON Le de sortie bornes MULTI SOURCE AUDIO• et peut _treniveau contr6[_ a I'aidedesdes touches MULTI VOLUME • (augmentation ou diminution multi-volume) de la t_l_commande RC872 ou sur les touches VOLUME UP et DOWN (augmentation ou diminution multi-volume) de la t_lecommande source RC-873. DISPLAY STEREO....... TUN EC_ _ _ ___ 2 4 (RC-872) Appuyer r_p@titivement sur la touche MULTI SOURCE jusqu'a ce que "MULTI OUT" (sortie multisource) apparaisse sur I'affichage Activer I'indicateur "MULTI" MULTSOURCE _ooE SELEOT (RC-873) •_ REGLAGE PAR DEFAUT (MULTI VOLUME --- dB (MINIMUM) LEVEL) : Lorsque MULTi fonction esta r_gl_e sur TUNER, le canal SOURCE pr_r_gl_ (multi-source) peut 6tre selectionn_ I'aide des touches PRESET (prSr_glage) Haut et Bas de la t_lecommande multi-source RC-873 (Ceci est seulement possible Iorsque I'unite principale est en mode MULTI) REMARQUE: I1est a noter que cette touche commute _galement le canal de r_ception prer_gl_ sur I'unit_ principale lots de la lecture ou de I'enregistrement du tuner en mode MULTI 46 • Lecture multi-source et multi-zone SYSTEME DE DIVERTISSEMENT MUSICAL MULTI-PIECE • Lorsque les sorties des bornes MULTI SOURCE AUDIO/VIDEO OUT sont c_bl6es et raccord6es sur des amplificateurs de puissance ou des 6crans de t61evision install6s dans d'autres pi6ces, des sources diff6rents peuvent 6tre lues darts des pi#ces diff6rentes de la princ[pale, I&oQ cet apparefl et les autres p6fiph6riques de lecture sont install6s. (Se r6f6rer au sch6ma SUB ROOMq (piece secondaire 1) • Lorsque la sortie des bornes SPEAKER SYSTEM-B est cabl6e et connect6e a des enceintes dans une autre pi#ce, la m6me source peut 6tre lue dans la pi6ce prindpale et dans une pi6ce secondaire. R6glez le s61ecteur des enceintes SPEAKER A/B de cet appareil en fonction de la piece dans laquelle la source doit 6tre diffus6e (Se r6f6rer au schema SUB ROOM-2 (pi6ce secondaire 2.) • Lorsqu'une t61ecommande de piece _ piece vendue s6par6ment (DENON RC-616 ou 617) est c_bl6e et connect6e entre la piece principale et la pi6ce secondaire, les appareils t61ecommandables dans la pi6ce principaIe peuvent 6tre command6s depuis la piece secondaire a I'aide de la t616commande. Pendant une lecture multi-source source RC-873 fournie en SUB-ROOM 1, la sortie MULTI SOURCE de cet appareil peut 6tre contr61ee par la t616commande multi Les op6rations sur la t616commande RC-873 autres que I'augmentation et la diminution de volume de la sortie multi-source ne peuvent pas 6tre effectu6es Iorsque I'unit6 principale est en mode REC OUT (sortie d'enreg[strement). Pendant une lecture multi-source en SUB-ROOM 2, la sortie des lecteurs CD DENON ou des platines cassettes etc de cet appareil peut 6tre contr61ee par la t616commane du syst_me RC_872 Pour commander les appareils de lecture autres que ceux mentionn_s c[_dessus, utiliser la t_l_commande de I'appareil ou preregler une t61_commande programmable, vendue s_par6ment (DENON RCW70, etc). REMARQUES: • Utillser un cordon a fiche a broche coaxial de 75 _ / ohms pour les signaux video pour connecter et c_bler la sortie MULTI SOURCE VIDEO. Pour la sortie AUDIO, utlliser des cordons a fiche & broche de haute qualite d'une telle mani_re qu'il n'y ait pas de ronflement ou de bruit. • Pour les instructions sur I'installatlon et le fonctionnement des appareils vendus s6par6ment, se ref_rer aux modes d'emploi des appareils respectifs. SYSTEME PIECE-1 DE DIVERTISSEMENT MUSICAL PIECE PRINCIPALE PIECE-2 SYSTEM AM PU FICATE UR MULTI-PIECE ,q/ E D'ENCEINTE B I ,_ee • • SOURCE RC873 TELECQMMANDE MULTI¸¸ _ (ou TELECOMMANDE PROGRAMMABLE RC 770} • Accessoires • TELECOMMANDE RC 872 • TELECOMMANDE RC 873 • RC_72 DRA685 DE SYSTEME _ MULTI SYSTEME ELECOMMANDE RC872 DE SOURCE Vendu separement • EMETTEUR IR RC-616 • DETECTEUR RC-617 • TELECOMMANDE PROGRAMMABLE RC 770 _4 Se r6f6rer et 33. a CONNEXtONS dans les pages 32 47 Utiliser cette touche pour contr61er une source vid6o autre que la source audio. Maintenez enfonc6 le touche VIDEO SELECT jusqu'a ce que la source d6sir6e apparaisse sur I'ecran @ _ O _ o VlOEO SELECt o o o Do o o o o o o m oo ,_ R6gler le commutateur coulissant vers "AUDIO". 1 La source video change de ]a mani_re suivante chaque lois que la touche est enfoncee. _c_c_ 1- _-_ _ _ _ Annulation de la lecture simultanee • Appuyer a nouveau sur ]a touche VIDEO SELECT • Changer la source de programme au composant connecte la video. Utiliser cette fonction pour desactiver provisoirement la sortie audio. MUTING Appuyer sourdine) sur la touche MUTING (mise en -1 Annulation de la raise en sourdine Appuyer a nouveau sur la touche MUTING (raise en sourdine). • Precaution: La raise hors tension de I'appare[I permet d'annuler les reglages PHONES Connecter le casque a la prise casque du panneau avant. _ O oo o °T "°i 1 2 Appuyer enceintes sur les touches SPEAKER A ou B pour _teindre ES2:_ 2___ -2 SHUl HH _(_U_ R_gler le commutateur coulissant vers "AUDIO". 48 les Lorsqu'une commande visuellement. est 6xecut_e B partir de la t61_commande, L'6tat de service de I'appareil peut 6galement cette commande 8pparatt sur 1'8ffichage, ce qui rend sa v6rification possible 6tre v6rifi6 sur l'affichage en utilisant la proc6dure d_crite c[-dessous Appuyer sur 18touche STATUS. -_ R6gler ]e commutateur coulissant vers "AUDIO" -1 • Les sources d'entr6e et de sortie et le r_glage d'ambiance, etc apparaissent dans I'ordre sur I'affichage chaque fois que la touche est enfonc_e 1 Suivre les etapes 1 a 3 sous "Lecture Enregistrement d'un programme source". 2 D_marrer I'enregistrement sur la platine a cassettes ou le magn6toscope. Pour les instructions, se rapporter aux instructions d'utilisation de I'appareil simultane Les signaux de la source s61ectionn6e avec la touche de selection de fonction sont transmis simultan6ment aux prises TAPE et VCR REC OUT. Si un total de deux platines a cassettes/magn6toscopes sont connect_s et r_gl6s en mode d'enregistrement, la m6me source peut 6tre enregistr@e simultan6ment sur chaque platine/magn6toscope De plus, s[ la touche TAPE MONITOR est enfonc6e, les signaux audio de la plagne a cassette sont transmis aux prises VCR AUDIO REC OUT. • Fonction de contr61e de bande Lorsqu'une platine a cassettes a trois t_tes est utilisee, I'enregistrement en appuyant sur la touche TAPE MONITOR Appuyer 8 nouveau sur la touche pour annuler le contr61e le son r6sultant de I'enregistrement en cours peut 6tre contr616 pendant 49 [] ECOUTER DE LA RADIO Cet appareil est 6quip_ d'une fonction pr6r6gl6e. de recherche automatique d'6missions 2 G I::::_ I::::_ O 1 0 O O 0 0 O de radiodiffusion en FM et de leur stockage darts la m_moire Eteignez I'appareil. Allumer I'appareil en utilisant I'interrupteur de mise en marche tout en maintenant enfonc_ le touche MEMORY. L'appareil commence automatiquement la recherche de stations de radiodiffusion en FM 0 ON / STANDBY 3 OO O 2 Lorsque trouv6e, au canal stock6es C18C8, la premiere station de radiodiffusion en FM est cette station est stockee dans la m6moire pr6r6glee A1. hes stations su_vantes sont automafiquement dans I'ordre aux canaux pr_r6gles A2 a A8, B1 B B8, D1 BD8etE1 a E8 pour un maximum de 40 stations Le canal prer6gl6e A1 est syntonis6 memoire automatique apr_s la fin de I'op6ration de REMARQUES: • Si une station FM ne peut pas 6tre automatiquement pr6rSgl_e cause d'une mauvaise r6ception, utiliser I'op_ration de "Syntonisation manuelle" pour syntoniser la station, puis la pr6regler en utilisant I'operation de "M6moire pr_regl6e" manuelle • Pour interrompre • VALEUR PAR DEFAUT AUTO TUNER PRESETS 50 A1 - A8 87,5/89,1/98,1/107,9/90,1/90,1/90,1/90,1 B1 - B8 520/600/1000/1400/1500/1710 C1 _ C8 90,1 MHz D1 _ D8 90,1 MHz E1 - E8 90,1 MHz MHz kHz/90,1/90,1 MHz cette fonction, appuyer le touche d'alimentation 4123 o C_-_@,.) D o o o o o R_gler la fonction d'entr6e B "TUNER". TUNER En regardant I'affichage, appuyer sur la touche BAND (bande) pour selectionner la bande d6siree (AM ou FM) BA_D (_ Appuyer sur la touche MODE (mode) pour r6gler le mode de syntonisation automatique. MODE _(_ o o o oo O O % ANume AJTo °' -M "f C'F _A TUNEn Appuyer sur la toucheTUNING UP (augmentation de syntonisatJon) ou TUNING DOWN (diminution de syntonisation). • La recherche automatique station est syntonisee. _" commence, TUNING oow. p , ,, _ puis s'arr6te Iorsqu'une REMARQUE: • Tout elq 6tant elq mode de syntor_isation automatique sur ]a balqde FM, le t6moin "STEREO" s'allume sur I'affichage Iorsqu'une 6mission st6r_o est syntonis6e. Aux fr6quences ouvertes, le bruit est mis en sourdine etles t6moins "TUNED" et "STEREO" s'eteignent R_gler la fonction d'entr6e B "TUNER". En regardant I'affichage, pour s@lectionner la bande appuyer d6siree sur (AM laoutouche FM) Appuyer sur la manuelle touche MODE r6gler "AUTO" le mode de de syntonisation Vedfier(mode) que pour le t6rnoin I'affichage s'eteint BAND (bande) A Appuyer sur la touche TUNING UP (augmentation de syntonisation) ou TUNING DOWN (diminution de syntonisation) pour syntoniser la station d_sir6e La fr6quence change continuellement Iorsque la touche est maintenue enfonc6e. REMARQUE: • Lorsque le mode de syntonisation s'eteint manuelle est r6gl_, les emissions en st6reo FM sont reques en mode monaural et le t_moin "STEREO" 51 23 4, t I Utiliser I'operation de "Syntonisafion automatique" ou de "Syntonisation manuelle" pour syntoniser la station a prer6gler dans la m6moire == ?[![_ t:_J t:_J MEMORY oo _o Appuyer sur la touche MEMORY(memoire). % Appuyer sur la touche SHIFT et s61ectionner le bloc de memoire d6sire (A aE). SH_FT _'_ O Appuyer sur la d_sir6 touche (1canal canal pr6r6gl6 a 8). pr6r6gl6 (1 a 8) pour s61ectionner le 6666_666 ,_ Pour pr_r6gler d'autres canaux, r6p6ter les etapes 1 a 4 Un total de 40 stations de radiodiffusion peut 6tre pr6r_gl6es -- 8 stations (canaux 1 8 8) darts chacun des blocs A B E. 2 En regardant I'affichage, appuyer sur la touche s61ectionner le bloc de memoire pr6r6gl_. SHIFT % D O oo O SHIFT pour SHIFT ,_ R_gler le commutateur coulissant vers "AUDIO" 2 Tout en regardant I'affichage, appuyer sur la touche -1 -2 52 canal pr_r6gl6 (1 a 8) pour s_lectionner le canal pr6r6gl6 d6sir_ (Lors de I'utilisation de la tel_commande, s_lectionner le canal pr_r_gle en appuyant sur la touche pr_r_glage Haut ou Bas 6666 ° c_ [] INITIALISATION DU MICROPROCESSEUR Lorsque I'indication de I'affichage est anormale ou quand I'utilisation de I'appareil ne donne pas les r_sultats escompt6s, 6tre initialise en suivant la proc6dure suivante 2 o C_::_5.'; doit Eteindre I'appareil et retirer le cordon CA de la prise murale. o o o o o o o MEMOIRE Maintenir le touche TUNING UP suivant et le touche TUNING DOWN, et brancher le cordon CA dans la pnse o o o Do [] le microprocesseur OO DE DERNIERE O V_rifier son les int6gralit6 intervalle que de I'affichage 1 seconde clignote environ, dans rel_cher doigts touches, et le microprocesseur sera initialise Bun 2 des FONCTION • Cet appareil est equip6 d'une m6moire de derni_re fonction qui stocke les conditions des r6glages d'entr6e et de sortie telles qu'elles _taient imm6diatement apr6s la raise hors tension. • L'appareil est egalement _quip6 d'une memoire de sauvegarde. Cette fonction fournit approximativement une semaine de stockage de memoire Iorsque I'unit_ principale est raise hors tension et avec le cordon d'alimentation debranch6. 53 [] DEPISTAGE DES PANNES Si un probleme se produit, verifier d'abord les points suivants: 1. Les connexions sont-elles correctes ? 2. L'ampli-tuner a-t-il ete utilise conformement au mode d'emploi ? 3. Les enceintes, la platine tourne-disque et les autres appareils fonctionnent41s correctement ? Si cet appareil ne fonctionne pas correctement, v6rifler les points 6num6r6s darts le tableau ci-dessous. Si le probl_me persiste, il peut y avoir un mauvais fonctionnement Debrancher imm6diatement le cordon d'alimentation et contacter le revendeur. Sympt6me Cause Affichage pas allume et aucun son n'est produit Iorsque I'appareil est allume • Le cordon branche d'alimentation n'est pas bier Remedes Page * Verifier I'insertion de la fiche du cordon d'alimentation * Mettre SOdStension avec ia telecommande 32 43 apres avoir enclenche la touche d'alimentation • Les cordons correctement Aff chage allume produit maEs aucun son n'est des enceintes branches ne SORt pas • Mauvaise postion de la touche de fonction audio • Commande de volume rsglse au minimum 4 • La sourdine (MUTING) est act vee • Les bornes circukees L'aff chage -- PROTECT -- apparait o- s Le son n'est produit que par un canal Les positions des nstrumentssont inversees pendant la lecture en stereo Un bourdonnement est produit pendant la lecture d'un disque _- Un hudement est produit Iorsque le SORt court- • Les trous de ventilat on de I'appareil obstrues • L'appareil puissance appropdee o_ d'enceinte SORt fo_ctionne en continu a haute et/ou la ve_tilation n'est pas • Connexion d'enceinte • Connexion d'entree/sort * arancher correctement * Regler surune pos tion appropr ee 44 * Augmenter le volume jusqu'a un nveau appropde * Desenclencher la sourdine (MUTING) • Mettre I'appareil hors tension, correctement les enceintes, remettre SOdStension connecter puis le 44 48 35,36 puis bier I'aerer pour le 31 Des que I'appareil est refroidi, le rallumer • Eteindre I'appareil, puis bier I'aerer pour le refroid r 31 • Eteindre I'appareil, refroid r Des que I'appareil est refroidi, le rallumer incomplete des cordons • Bienconnecter 35,36 incomplete e des cordons • Bienconnecter 35_37 • Inverser les connexions des enceintes gauche et droite ou des cordons d'entree/sort e gauche et droite • Verifier les connexions • Le fil de masse de la platine toume-disque n'est pas correctement connecte • Connexion de la prise PHONO incomplete • Antenne radio ou TV proche • BieR connecter 35 • BieR connecter • Contacter le revendeur 35 • La platine tourne-disque et les systemes d'enceinte SORt trop proches les uns des autres • Le sol est instable et vibre facilement • Les eloigner le plus possible volume est eleve • Utiliser gauche et droite des amortisseurs pour absorber 35 _ 39 les vibrations des enceintes transmises par le sol Si la platine tourne-disque n'est pas 6qu_pse d'solantSr audio (disponibles Le son estdeforme 35, 36 • La pression faible • Poussiere lecture de la pointe de lecture est trop ou salete • CelUe defectecommande • Une cellule ut lisee a bobine sur la pointe de est utilisee mobile (MC) utilser des isolants darts le commerce) • Appliquer une press on de pointe de lecture appropdee •Vedfierlaponte delecture • Remplacer la cellule est Levolumeestfaible • La remplacer par une cellule a aimant mobile (MM) ou utiliser un amplificateur de t6te ou installer un transformateur 35 survolteur E 54 Cetappareilnefonctionnepas correctement Iorsque la telecommande est utilisee • Les piles SORt usees • Telecommande trop loin de cet appareil Remplacer les pileo par des piles neuves • Rapprocher 38 38 •Obstacle entre cet appareil et la tel6commande • Une touche differente est enfoncee • Les p61es (_ et e de la pile SORt inseres a I'envers • Retirerl'obstacle 38 • Appuyer sur la touche appropriee • Inserer correctement les piles 38 [] SPECIFICATIONS • Section audio (Amplificateur de puissance) Puissance de sortie nominale: 100 W + 100 W (8 _/ohms, Bornes de sortie: 20 Hz - 20 kHz avec D.HT. de 0,05%) Aou B 44 16 _/ohms A + B 88 16_/ohms Analogique (Analog) Entree LINE -- PRE-OUT Sensibilit_ d'entree/Imp_dance d'entr_e: R_ponse en frequence: 200 mV / 47 k_/kohms 10 Hz _ 50 kHz +1,5 dB 100 dB (IHF-A charg6e) Rapport signal/bruit: Distorsion harmonique totale: Niveau de sortie nominal: Entree PHONO -- REC OUT 0,009 % (-3 dB a la sortie nominale,8 _2/ohms) (1 kHz) 1,2V Sensibilite d'entr_e/Impedance d'entree: 3,0 mV / 47 k£)./kohms R_ponse en frequence: +0,5 dB (20 Hz - 20 kHz) Rapport signal/bruit: Distorsion harmonique 74 dB (IHF_A chargee avec 5 mV en entr6e) totale: Niveau de sortie nominal/Maximum: 0,03 % (1 kHz, 3 V) 150mV / 7V • Section video (Prises video standard) Niveau/imp_dance d'entrde et de sortie: Reponse en frequence: 1 Vc-c, 75 _/ohms 5 Hz B 10 MHz +1, -3 dB • Section tuner [FM] (Remarque: Gamme de reception: Sensibilite utile: Seuil de sensibilit_ 50 dB: Rapport signal/bruit Distorsion (IHF-A): harmonique totale 87,5 MHza 107,9 MHz pV a 75 £_/ohms, 0 dBf [AM] 520 kHza 1710 kHz 1,4 #V (14,2 dBf) 18pV MONO STEREO 2,8 pV (20,2 dBf) 23 pV (38,5 dBf) MONO 80dB STEREO 75 dB (IHF-A chargee) MONO 0,15% (1 kHz) STEREO 0,3 % (1 kHz) 1 x 10 _"W) (]HF-A chargee) • Generalites Alimentation: Consommation: Dimensions CA 120 V, 60 Hz externes maximales: 3,4 A 434 (L) x 171 (H) x 416 (P) mm Poids: 10,0 kg (22 Ibs) • Telecommande RC-872, RC_873 RC-872 Piles: Dimensions Type R6P/AA (deux piles) externes: Poids: 54 (L) x 172 (H) x 27,2 (P) mm 100 g (avec les piles) RC-873 Piles: Dimensions Type R03/AAA (deux piles) externes: Poids: 47,5 (L) x 127 (H) x I8 (P) mm 70 g (avec les piles) * Aux fins d'am61ioration, les sp6ciflcations et la conception sont sujettes a modification sans preavis 55 NIPPON 14 14, AKASAKA COLUMBIA 4-CHOME, MINATO KU, TOKYO CO., LTD. 107 8011, JAPAN Telephone: (03) 3584 8111 Cable: NIPPON COLUMBIA TOKYO Telex: JAPANOLA J22591 Printed in Korea 511 3580 108
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 56 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Mon Apr 02 19:16:41 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools