Denso Wave orporated DWBT013 Bluetooth Adapter User Manual

Denso Wave Incorporated Bluetooth Adapter

User Manual.pdf

Jun 10, 20141DWBT013 Installation ManualContents1. Supply Voltage2. Dimensions and Connector specification 3. Notice
Jun 10, 201421. Supply VoltageDC 3.0-3.6VSupply Voltage Range (Note)DC 3.3VSupply VoltageSpecificationsItemNote: These values are specified at the connector terminal.
Jun 10, 201432. Dimensions and Connector specification (15mm)(31mm)(3mm)Specification: 0.5mm PITCH FPC CONNECTORCircuits: 18ConnectorLabel(Electronic components were omitted)
Jun 10, 201443. NoticeThis device complies with part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.When the DWBT013 is installed in Class A equipmentWhen the DWBT013 is installed in Class B equipmentNote: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.
Jun 10, 2014Radiation Exposure Statement:The product comply with the FCC and Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établiespour un environnement non contrôlé.Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut êtreaugmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé surla puissance de sortie la plus faible si une telle fonction est disponible.Déclaration d'exposition aux radiations:Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.FCC CAUTION:
Jun 10, 2014IMPORTANT NOTE:In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC and Canada authorization is no longer considered valid and the FCC ID and IC-ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Canada authorization.NOTE IMPORTANTE:Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'IDIC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produitfinal (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.This device is intended only for OEM integrators under the following conditions:1)The transmitter module may not be co-located with any other transmitter or antenna. 2)Module approval valid only when the module is installed in the tested host or compatible series of hostAs long as 2conditions above are met, further transmitter test will not be required. However, the OEM integrator is stillresponsible for testing their end-product for any additional compliance requirements required with this module installedCet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module)1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.2) L'approbation du module est valable uniquement lorsque le module est installe dans l'equipement teste ou dans des equipements compatibles testes.Tant que les 2conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutesexigences de conformité supplémentaires requis pour ce module installé.
Jun 10, 20147Please describe the following warning on the End product which contains this module.Contains Transmitter Mobile FCC ID:PZWDWBT013IC:1551C-DWBT013 Contains FCC ID:PZWDWBT013IC:1551C-DWBT013or

Navigation menu