Detex Installation Instructions For 03W Advantex Trim 101260

User Manual: Detex Installation Instructions for 03W Advantex Trim Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 4

DownloadDetex Installation Instructions For 03W Advantex Trim 101260
Open PDF In BrowserView PDF
101260 May 29, 2007

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045
(830)629-2900 / 1-800-729-3839 / Fax (830)620-6711
E-MAIL: detex@detex.com
INTERNET: www.detex.com

INSTALLATION INSTRUCTIONS FOR 03W ADVANTEX TRIM

TOOLS AND SUPPLIES
Safety Glasses
(Always put on safety glasses prior to beginning installation of unit)
Pencil
Center Punch
Hammer
Drill Motor
Drill Bits & Taps
Screw Driver (Phillips Drive)
Tape Measure

DETEX INS-101260

PREPARING THE TRIM:
1. Assemble the cylinder bracket and cylinder as shown (Fig. T1). Cut cylinder screws as
required.

Fig. T1

PREPARING THE DOOR:
1. Center punch hole "a" marked earlier.
2. Drill two (2) pilot holes "a" (holes located diagonal from each other). Caution: Be sure to
drill STRAIGHT through the door.
3. Drill pilot holes for remaining holes "a" through inside of door only.
4. Using the backplate as a template on the outside door face, align the two through-holes.
Mark and center punch the two (2) remaining holes "a".
5. Note: Verify that the slotted edge of the backplate faces the edge of the door. Mark the
outside trim cam hole "d".
6. Drill pilot holes "a" through outside of door only.
7. Drill four (4) 3/8" holes partway through the door. Complete these holes by drilling from the
opposite door face.

Page 2

8. At the outside trim cam hole "d", measure up 1/4" and make a new mark. This will be the
center of the outside trim cylinder. Center punch and drill a 1-1/2" hole. Repeat for inside of
door.
ASSEMBLING THE OUTSIDE TRIM AND BACKPLATE:
1. Place the trim assembly against the door, aligning the cylinder tailpiece through the backplate
trim cam.

MARK TAILPIECE HERE

CUT THIS SIDE OF MARK

Fig. T2A

Fig. T2B

2. Mark the tailpiece as it protrudes through the cam (see Fig. T2A).
3. Remove trim assembly and cut the tailpiece just inside of the mark (see Fig. T2B). Caution:
Tailpiece must not extend past the cam.

Page 3

Fig. T3

4. Align the four sex nuts and trim assembly through the drilled holes (Fig. T3).
5. With the key out of the cylinder, align the tailpiece extension into the backplate's trim cam on
the inside door face.
6. It may be necessary to hammer the sex nuts into the door face.
7. Fasten the backplate to the inside door face with 1/4-20 machine screws provided. Caution:
Do not overtighten.
8. Key should turn freely in both counter clockwise and clockwise directions.
9. Resume with panic hardware instruction #15.

Page 4
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:12:18
Create Date                     : 2009:06:22 16:09:13-05:00
Metadata Date                   : 2009:06:22 16:09:16-05:00
Modify Date                     : 2009:06:22 16:09:16-05:00
Creator Tool                    : Adobe InDesign CS4 (6.0.2)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7559 bytes, use -b option to extract)
Instance ID                     : uuid:3f58eb0e-7685-4ebc-bfb2-106bfadaf63a
Document ID                     : xmp.did:451402804E24DE11A87DC6427201DEC6
Original Document ID            : xmp.did:451402804E24DE11A87DC6427201DEC6
Rendition Class                 : proof:pdf
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:451402804E24DE11A87DC6427201DEC6, xmp.iid:461402804E24DE11A87DC6427201DEC6, xmp.iid:471402804E24DE11A87DC6427201DEC6, xmp.iid:481402804E24DE11A87DC6427201DEC6, xmp.iid:4B1402804E24DE11A87DC6427201DEC6, xmp.iid:4C1402804E24DE11A87DC6427201DEC6, xmp.iid:B9F480E15A24DE11A87DC6427201DEC6, xmp.iid:2410BB903C25DE11B8A994EF857D7DD6, xmp.iid:56ADB3AF645FDE11A670F7C8E7E7B669
History When                    : 2009:04:08 10:04:04-05:00, 2009:04:08 10:07:23-05:00, 2009:04:08 10:07:23-05:00, 2009:04:08 10:08-05:00, 2009:04:08 10:20-05:00, 2009:04:08 10:27:23-05:00, 2009:04:08 11:44:29-05:00, 2009:04:09 16:11:37-05:00, 2009:06:22 16:09-05:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /, /, /, /
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:28470940-b361-44a2-a6b0-2d881f4fe55c, uuid:b01bf5b1-6ce7-40b5-867c-934dc7ffc133, uuid:57a5bd70-a462-4ad5-9cce-84d0140b6b0d, uuid:0b631335-5dc7-42b0-9f60-470362253ab8, uuid:ede3aa86-eb8f-4bb2-9e94-c8ef405042f6
Manifest Reference Document ID  : xmp.did:ADE7C0844724DE11B414F4099639F633, uuid:5C345DE89C6ADB119F1393E5814F3D54, xmp.did:AEE7C0844724DE11B414F4099639F633, xmp.did:AFE7C0844724DE11B414F4099639F633, xmp.did:B0E7C0844724DE11B414F4099639F633
Doc Change Count                : 1
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Count                      : 4
Creator                         : Adobe InDesign CS4 (6.0.2)
EXIF Metadata provided by EXIF.tools

Navigation menu