DewertOkin OM1089 Double Drive with RF-Transmitter 2.4GHz User Manual
DewertOkin GmbH Double Drive with RF-Transmitter 2.4GHz
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3406851 |
| Application ID | eWnjRmQeee5qbUjZBZ25og== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 87.95kB (1099318 bits) |
| Date Submitted | 2017-05-29 00:00:00 |
| Date Available | 2017-05-29 00:00:00 |
| Creation Date | 2015-06-26 14:56:08 |
| Producing Software | Adobe PDF Library 9.0 |
| Document Lastmod | 2017-03-06 06:37:23 |
| Document Title | user manual |
| Document Creator | Acrobat PDFMaker 9.1 für Word |
OKIMAT 8
OKIMAT 8+2 FURNIBUS
Installation Instructions
(Translation of the original installation
instructions)
OKIMAT 8
Foreword
Foreword
Disclaimer and exclusion of liability
DewertOkin is not responsible for damage resulting from:
• failure to observe these instructions,
• changes made to this product which have not been approved by DewertOkin, or
• the use of replacement parts which have not been approved or manufactured by DewertOkin..
We reserve the right to make unannounced technical changes in the course of our continual
product improvement process!
Creation of a complete operating instruction manual for the entire end product
These instructions are only intended to be used by the end-product manufacturer. They should not
be given to the operator of the end product. The factual information contained within may be used
as a basis when creating the end-product manual.
The warning and danger notices are best suited for use in the end product's manual. However it is
not sufficient to simply follow these notices. You should also carry out an internal risk assessment
for your end product. This can then be used as the basis for the safety notices in your manual.
These installation instructions do not contain all information required to safely operate the end
product. They only describe the installation and operation of the drive as partially completed machinery.
The instructions are intended for the technicians responsible for manufacturing an end product and
not for the operators of the end product.
Notice for customers in EU nations
German Inspection Authority (TÜV SÜD Product Service) testing label
The construction of the OKIMAT 8 has been inspected by the German Inspection Authority (TÜV).
The TÜV also monitors the production of the OKIMAT 8. The official German TÜV label certifies
this construction inspection and production monitoring.
Figure 1
69596(c)
TÜV label
Table of contents
OKIMAT 8
Table of contents
Foreword
Disclaimer and exclusion of liability
Creation of a complete operating instruction manual for the entire end product
Notice for customers in EU nations
Table of contents
1.
General Information
1.1
Safety notices within the installation instruction and the operating instructions for
the entire machine
1.2
Conventions used
2.
Safety notices
2.1
Proper and intended usage
2.2
Selection and qualification of personnel
2.3
Notice on safety during operations
2.4
Product identification
3.
Possible combinations
10
4.
Description
11
4.1
Components
11
5.
Technical specifications
12
6.
Installation
14
6.1
Safety notices to observe during installation
14
6.2
Installation procedure
15
7.
Information about creating your Operating Manual
21
7.1
General information
21
7.2
Notice for operating with optional configuration
23
8.
Troubleshooting
26
9.
Maintenance
27
9.1
Maintenance
27
9.2
Cleaning and care
27
69596(c)
OKIMAT 8
Table of contents
10.
Disposal
28
10.1
Packaging material
28
10.2
Drive components
28
Declaration of incorporation/installation
29
EU Declaration of Conformity
30
69596(c)
General Information
1.
OKIMAT 8
General Information
These installation instructions must be followed closely in order to install this drive successfully and
safely in the end product. These instructions are not an operating manual for the end product.
These instructions will help you to minimize danger, repair costs and down times. They will also
help you to maximize the reliability and lifespan of the end product.
CAUTION
The notices in these instructions must be followed! Following the guidelines during installation
and connection procedures will help to minimize:
• the risk of accident and injury, and
• damage to the drive system or the end product.
These installation instructions have been written with due care and attention. However, we cannot
guarantee that the data, images and drawings are complete and correct nor do we accept any liability for the information contained therein, unless required by law.
Availability of this document
As manufacturer of the end product, you are obligated to comply with Machinery Directive
2006/42/EC. This directive stipulates that the installation instructions must be kept on file for governmental inspection purposes.
1.1
Safety notices within the installation instruction and the operating instructions for the entire machine
The manufacturer of the end product is only permitted to operate the OKIMAT 8 drive (by itself an
incomplete machine)
•
when the end product (for which the OKIMAT 8 drive is intended) is in compliance with all protective measures specified in the Machinery Directive 2006/42/EC, and
•
when the manufacturer expressly declares the compliance of the end product.
The manufacturer of the end product must create a manual for the users of that product. The safety
notices in the end-product manual must be written based on the end product's risk assessment.
1.2
Conventions used
Notices which do not relate to safety are indicated in these instructions with a triangle:
Triangular notice symbol
Safety notice explanations
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices which are not related to personal injury but may result in
damage to the product or surroundings.
69596(c)
OKIMAT 8
Safety notices
2.
Safety notices
2.1
Proper and intended usage
The OKIMAT 8 drive is meant to be installed in beds.
• It provides motor adjustment capabilities for movable reclining bed parts. It should be used in
conjunction with suitable fittings and mechanics:
CAUTION
Risk of accident
This drive should only be used for the applications described above. Any other use is forbidden.
Improper usage can lead to accidents or destruction of the unit. Such non-approved applications
will lead immediately to the expiration of all guarantee and warranty claims on the part of the
end-product manufacturer against the manufacturer.
Improper usage
Be sure to follow the notices below concerning improper usage. You should include them in your
product manual in order to inform the users of your end product.
The OKIMAT 8 drive should not be used:
• in any environment where combustible or explosive gases or vapours (e.g., anaesthesiology)
may be present,
• in a moist environment,
• outdoors,
• in any application that will be cleaned with an automated washing system,
• for raising and lowering loads in industrial or technical applications.
• with forces which exceed those specified on the ratings plate.
The OKIMAT 8 drive can be used by children of 8 years and older, persons with reduced physical,
sensory or mental capabilities, or persons with lack of experience or knowledge when they are supervised or instructed concerning the safe use of the device and when they understand the resulting risks. Do not allow children to play with this device. The cleaning and user maintenance must
not be carried out by children without supervision.
You should only use spare parts which have been manufactured or approved by DewertOkin.
Only these parts will guarantee a sufficient level of safety.
69596(c)
Safety notices
OKIMAT 8
Optional: battery-operated reset function
NOTICE
The battery-operated reset function is not a safety system and does not avert danger.
DewertOkin does not guarantee that the drive will function in the event of a power outage.
If the end-product manufacturer chooses to guarantee the functionality of the end product during a
power outage, then the end-product manufacturer is responsible for arranging a mechanism to ensure this functionality.
2.2
Selection and qualification of personnel
The installation of the drive in the end product may only be performed by qualified personnel.
2.3
Notice on safety during operations
Basic safety rules must be followed in order to ensure that the end product can be continually operated in a safe manner. These rules must be observed while using the end product and while installing the drive.
These rules and safety measures can be categorized as follows:
• Construction measures before the installation (refer to the "Safety notices to observe during installation" section in Chapter "Installation").
• Safety fundamentals during the drive installation and during cable and wire routing (refer to the
"Safety notices to observe during installation" section in the "Installation" chapter).
• Using the drive in intermittent duty (refer to the "General information" section in the "Information
about creating your Operating Manual" chapter).
• Basic safety rules during operation (refer to the "Information about creating your Operating
Manual" Chapter).
• The creation of a manual for the end product which contains these and other safety rules.
Creating a user's manual
The manufacturer of the end product must create a manual for the users of that product. The safety
notices in the end-product manual must be written based on the end product's risk assessment.
69596(c)
OKIMAT 8
Safety notices
2.4
Product identification
2.4.1
Ratings plate
The ratings plate shown is an example; the specifications for your drive may differ from this illustration.
Figure 2
Ratings plate example
OKIMAT 8+2, OKIMAT 8+2 FURNIBUS
Model name
xxxxx
Article number
24 – 29V
Input voltage
Max. 6.00A
Current consumption
Intermittent Operation 2min/18min
Intermittent operations: 2 minutes / 18 minutes
Max. force
Push force
Prod.date
Calendar week / year
2.40GHz
Frequency of the remote wireless version
Serial No.
Serial number for your drive
VRx
Software version
IP20
Protection degree
Stroke
Stroke (head / foot)
Use in dry rooms only!
Follow all special disposal instructions!
EU conformity mark
69596(c)
Possible combinations
3.
OKIMAT 8
Possible combinations
The OKIMAT 8 double drive can be combined for use with other single or double drives. The following basic combinations are possible:
• an OKIMAT 8 with a hand-held remote control,
• an OKIMAT 8 as the main drive and a single drive used as a slave drive with a hand-held remote,
• an OKIMAT 8 as the main drive and two single drives used as slave drives with a hand-held
remote.
Systems can be customized by combining drives with the hand-held remote and power supplies as
needed.
DewertOkin has separate system instruction manuals containing all information and instructions
needed for these systems.
Only a DewertOkin device should be used to control the drive since they have already been
verified to work together.
10
69596(c)
OKIMAT 8
4.
Description
Description
The drives units are powered by electrical motors. The back and leg sections of a bed can be adjusted depending on the drive options. The drive is controlled by means of an OKIN controller.
The different drive models vary according to their:
• motor power,
• number of motors,
• optional reset function,
• optional mains cut-off mechanism
• optional Floor lighting
• optional variant with an external switched-mode power supply (EPS),
• different stroke variants,
• integrated RF radio receiver,
4.1
Components
The components have a compact design – with two linear adjusting units and a control unit located
within an enclosed housing. To facilitate the tool-free assembly process, the two sliders on the side
(the shutters) can be removed from the housing.
Figure 3
Main components of the OKIMAT 8 double drive
A Optional snap-in locking device
B Shutters
C Connection socket
D Symbol for head end of bed
E Battery compartment
F Screw-on point for the external floor lighting
(optional)
G Symbol for foot end of bed
69596(c)
11
Technical specifications
5.
OKIMAT 8
Technical specifications
Power supply (AC)
or
Input voltage (DC)
120 / 230 / 240 V, 50/60 Hz (refer to the ratings plate)
Current consumption under rated load
(AC)
0.63 A AC – 3.15 A AC, depending on mains connection and load (refer to the ratings plate)
Current consumption under rated load
(24 V DC)
Max. 8.0 A DC
Permitted push force
Max. 6000 N
Mode of operation1 under max. rated load.
Intermittent duty 2 min./18 min.
Protection class
II or III (refer to the ratings plate)
24 V AC – 29 V AC (refer to the ratings plate)
Noise level
≤ 65 dB(A)
Current consumption of all additional drives
Max. 8 A DC
Drive type
Double drive
Drive options
OKIMAT 8, OKIMAT 8+1, OKIMAT 8+2
Protection degree
IP20
Stroke
87, 69 (standard), 48, 74, 79, 92
Length x width x height
714 mm x 179 mm x 119 mm
Axle gap distance
581 mm (± 2 mm)
Axle receptacle diameter
Ø 25 mm, Ø 34 mm (depending on application)
Weight
Approx. 5 kg
Optional: battery-operated reset function
Voltage
One or two nine-volt batteries (6LR61)
Optional: Remote wireless version
Frequency
2.40 GHz
Optional: Floor lighting
Light emitted from diodes
Laser class 1 (EN 60825-1:1994)
Ambient conditions for operation, storage and transport
12
Transport / storage temperature
From -20 °C to +50 °C (-4 °F to +122 °F)
Operating temperature
From +10 °C to +40 °C (+50 °F to +104 °F)
Relative humidity
From 30% to 75%
Air pressure
From 800 hPa to 1060 hPa
Height
< 2000 m
1)
Mode of operation: intermittent duty 2 min./18 min. This means that after the unit is operated with its rated
load for up to two minutes it must then be paused for 18 minutes. The system can malfunction if this pause
is not observed!
2)
No more than two drives may be operated at rated load simultaneously!
69596(c)
OKIMAT 8
Technical specifications
Dimensions of housing
119
179
714
Figure 4
Dimensions of OKIMAT 8 drive (in mm)
Dimensions of the pivot lever
581 ± 2
74.6
R 11
480 ± 2
Figure 5
72
50.5
Pivot lever position, in mm
Make sure that you consider the amount of torque that is generated by the drive when you design the weld between the bracket and the end product.
•
Max. torque: 435 Nm.
We recommend: the OKIN pivot lever (ID number 2.00.718.108.00)
69596(c)
13
Installation
OKIMAT 8
6.
Installation
6.1
Safety notices to observe during installation
Basic safety rules must be followed in order to ensure that the end product can be continually operated in a safe manner. These rules must be observed while using the end product and while installing the drive.
Avoiding fatigue fractures
Drives that are incorrectly installed can undergo fatigue fractures which then create a risk of injury.
•
Install the drive in the end product so that it is properly aligned. This will help prevent shear
stress.
•
Do not position the drive at a slanted angle when installing it in the end product. A slanted angle between the intended direction of movement of the end product and the drive's direction will
create shear stress and could lead to a fatigue fracture.
Avoiding a pinching hazard
When designing your end product, you should take the drive adjustment movement into account
with passive safety mechanisms and with the appropriate safety notices in your operating instructions.
• Installation methods for ensuring passive safety: Install the OKIMAT 8 drive so that none of the
positions where shear and pinch hazards exist are accessible externally.
Make sure that your operating instructions inform the user of these safety points.
14
69596(c)
OKIMAT 8
Installation
6.2
Installation procedure
6.2.1
An example installation
Before installing the drive, make sure that you are observing all of the safety notices found in the
"Safety notices to observe during installation" section.
1 Move your product into a position where it is supporting no load.
CAUTION
Danger of crushing injury!
• Be sure to carry out work on the drive in a position so that no loads are bearing on it. Only in
this way can you be sure to avoid any risks of crushing or injury.
•
Disconnect the nine-volt battery if you are using the battery-operated reset function.
2 Pull the shutters firmly to the side (A). The slots (B) for the brackets (D) are now uncovered.
Figure 6
Installing the double drive
A Shutters
B Fitting mounts
3 Align the OKIMAT 8 next to your product. The slots for the back and leg sides must be properly
aligned with the correct brackets on your end product (refer to the symbols on the OKIMAT 8 as
described in Figure 3).
Figure 7
Installing the double drive
C End product (bed)
69596(c)
D Brackets
15
Installation
OKIMAT 8
Figure 8
Installing the double drive
4 Push the drive in so that the brackets (D) fit into the slots (B). Press in until the tubes snap into
the brackets.
5 Close the shutters (A) on the drive by snapping them back in. The OKIMAT 8 is now securely
attached to the end product.
6 Disconnect all additional components (handset, etc.) from their sockets.
7 Now connect the drive to the power supply.
Please note, after the power supply has been connected:
There is a delay after the supply voltage is applied before the device actually turns on. Wait at
least two seconds before beginning the commissioning.
6.2.2
Electrical connection
CAUTION
Risk of accident
Electrical components should be connected or disconnected only when the power supply cord is
unplugged.
Only the following personnel are qualified to work on the power cord or to replace the power cord:
• someone who has completed training in electronic motor assembly,
• someone with equivalent qualifications, or
• someone who has successfully completed the appropriate DewertOkin training program.
You should only work on the power cord when you are qualified to do so. Otherwise, a properly
qualified person should be found for this task.
There is a delay after the supply voltage is applied before the device actually turns on. Wait at
least two seconds before beginning the commissioning.
16
69596(c)
OKIMAT 8
Installation
Option: Connecting the OKIMAT 8 to an external switched-mode power supply (SMPS)
The OKIMAT 8 should be connected to an external switched-mode power supply (SMPS: such as
the PD12/PD13 power supply with the country-specific mains plug as described in the power supply's installation instructions) using a connecting cable, as shown in Figure 9.
Figure 9
Connecting the OKIMAT 8 to an external switched-mode power supply (SMPS)
A Switched-mode power supply
(such as the PD12/PD13)
69596(c)
B OKIMAT 8 connecting cable
17
Installation
OKIMAT 8
Optional: battery-operated reset function
Connecting the nine-volt batteries
Figure 10
Connecting the 9-V battery/batteries
A Battery clip connected,
B Battery clip, unattached
C 9-V battery (type 6LR61)
Connect the nine-volt batteries first when you would like to perform a battery-operated reset.
The batteries may only be used to power the reset function one time. Take out the batteries and
dispose of them properly after the reset function has been carried out.
Routing the electrical cables
When routing the cables, be sure that:
• the cables cannot get jammed,
• no mechanical load (such as pulling, pushing or bending) will be put on the cables, and
• the cables cannot be damaged in any way.
Fasten all cables (especially the mains cable) to the end product using sufficient strain relief and
kink prevention methods. Be sure that the design of the end product prevents the mains cable from
coming into contact with the floor during transport.
18
69596(c)
OKIMAT 8
6.2.3
Installation
Dismantling
CAUTION
Risk of accident
• Work on electrical components should be conducted only when the mains power connection
is unplugged.
• Disconnect the nine-volt battery if you are using the battery-operated reset function. ..
Certain details may change because of technical changes.
Figure 11
Removing the double drive
1 Move your product into a position where it is supporting no load.
CAUTION
Danger of crushing injury!
Be sure to carry out the removal work on the drive in a position so that no loads are bearing on
it. Only in this way can you be sure to avoid any risks of crushing or injury.
2 Disconnect the OKIMAT 8 from the power supply!
3 Disconnect all additional components such as slave drives or handset from their sockets.
Be sure to support the drive's weight to prevent it from falling.
4 Open the optional snap-in locks on the cover (A) until they snap in.
5 Pull the shutters firmly to the side (A).
69596(c)
19
Installation
OKIMAT 8
Figure 12
Removing the double drive
C End product (bed)
D Brackets
6 Pull out the OKIMAT 8 far enough so that the brackets (D) are out of the slots (B). The OKIMAT
8 is now unattached and can be removed.
Figure 13
A Shutters
Removing the double drive
B Fitting mounts
7 Push the shutters (A) back onto the OKIMAT 8 so that they are not lost during transportation.
Close the optional locking device.
20
69596(c)
OKIMAT 8
7.
Information about creating your Operating Manual
Information about creating your Operating Manual
The factual information contained within may be used when you are creating the end-product manual. The installation instructions do not contain all information required for the safe operation of the
end product. They only describe the installation and operation of the drive as a partially assembled
piece of machinery.
When creating the operating instructions, remember that the installation instructions are intended for qualified specialists and are not for typical users of the end product.
7.1
General information
Only a DewertOkin device should be used to control the drive since they have already been
verified to work together.
Delayed start-up
After plugging the power plug into the power outlet:
There is a delay after the supply voltage is applied before the device actually turns on. Wait at
least two seconds before beginning the commissioning.
Power-on time / intermittent operations
The OKIMAT 8 drive has been designed for intermittent operations. Intermittent operation is an operational mode where the drive must pause after a specified maximum period of operation (poweron time). This protects the drive from overheating. Extreme overheating can cause a malfunction.
The ratings plate specifies the maximum power-on time and the required pause intervals.
Avoiding toggle operations
You should avoid switching from one direction of travel to the opposite direction without first stopping the motor. Make sure that you pause between motions! A pause (motor stop time) can be activated using the controls.
You should always avoid a quick change (toggling) of directions.
69596(c)
21
Information about creating your Operating Manual
OKIMAT 8
Shutting off the drive
To shut off the drive, first disconnect the system from the power supply and then disconnect the
battery. The power supply must always be accessible during operations so that the system can be
shut off.
Avoiding cable damage
Be sure that your operating instructions inform the user about the possible cable risks.
NOTICE
The cables (particularly the mains cable) should not be run over. In order to prevent injuries or
drive damage, no mechanical strain should be placed on the cables.
22
69596(c)
OKIMAT 8
Information about creating your Operating Manual
7.2
Notice for operating with optional configuration
7.2.1
Optional: battery-operated reset function
The battery-operated reset function allows the drive system to be operated during a power outage.
One or two 9-V batteries can be used to power the OKIMAT 8 in the event of a power outage. The
batteries should be connected only then when the outage occurs. The batteries are not connected
by default since they have very limited capacity. They can only be used to power the reset function
once. The used batteries should then be replaced and properly disposed of.
NOTICE
The battery-operated reset function is not a safety system and does not avert danger.
When working with radio units (RF), first disconnect the drive system from the power supply! Connect the nine-volt battery first when you would like to perform a battery-operated reset. The battery
may only be used to power the reset function one time. Take out the battery and dispose of it properly after the reset function has been carried out.
NOTICE
Connect the nine-volt batteries first when you would like to perform a battery-operated reset. The
batteries may only be used to power the reset function one time. Take out the batteries and dispose of them properly after the reset function has been carried out.
NOTICE
When using the electrical reset function, make sure that the entire movement is executed without
interruptions.
If the end product is under a heavy load which prevents the reset function from operating, the
strain or load on the end product must first be removed before a reset can be carried out.
69596(c)
23
Information about creating your Operating Manual
7.2.2
OKIMAT 8
Programming the RF hand-held remote
Figure 14
Function key on the OKIMAT 8
A Function key (at rear of the drive)
1 Press the drive's function key (A) twice (a quick double click). The drive will be in the teach-in
(programming) mode for approximately 10 seconds. The LED on the function key lights up.
More information on programming the hand-held remote and its key functions is provided in the
hand-held remote's manual.
24
69596(c)
OKIMAT 8
7.2.3
Information about creating your Operating Manual
Optional: integrated floor lighting
The integrated floor lighting should only be used for illuminating under the bed. It is built into the
front or back of the double drive, as shown in Figure 15.
Figure 15
Location of the integrated floor lighting (optional)
A Floor lighting on front
B Floor lighting on back
CAUTION
Never look directly into the light from the floor lighting. Never point the floor lighting towards
someone's eyes.
Depending on the handset or hand-held remote that you are using, the internal floor lighting can be
switched on either by pressing simultaneously on both the up and down keys for the first OKIMAT 8
motor, or by pressing the special floor lighting key on the handset/hand-held remote.
7.2.4
Optional: external floor lighting
The Floor Lighting Assembly Instructions describe how to install and operate the external floor
lighting.
69596(c)
25
Troubleshooting
8.
OKIMAT 8
Troubleshooting
This chapter describes troubleshooting methods for fixing problems. If you experience an error that
is not listed in this table, please contact your supplier.
CAUTION
Only qualified specialists who have received electrician training should carry out troubleshooting
and repairs.
Problem
Possible cause
Solution
The handset or drive
system is not functioning.
There is no mains supply voltage.
Connect the mains power.
The hand switch or drive system
is defective.
Please contact your supplier or
sales agent.
The drive is suddenly
not capable of movement.
Possibly the thermal circuit
breaker on the transformer has
been triggered or is defective.
Remove the power plug and allow
the drive system to rest for 20 to
30 minutes.
The thermal fuse on the transformer may have been triggered.
Please contact your supplier or
sales agent.
The unit's fuse may have been
triggered or may be broken.
Please contact your supplier or
sales agent.
There is no mains supply voltage.
Connect the mains power.
A lead-in connection has been
interrupted (mains power, hand
switch or auxiliary drive).
Check the lead-in connections
and re-seat the contacts if required.
The batteries are empty.
Check the batteries and replace if
necessary.
Battery is not connected.
Connect the battery or batteries.
The battery-operated
reset is not functioning.
26
69596(c)
OKIMAT 8
Maintenance
9.
Maintenance
9.1
Maintenance
The OKIMAT 8 drive requires no maintenance.
9.2
Cleaning and care
Clean the OKIMAT 8 drive as needed using a dry cloth.
NOTICE
• Always disconnect the power supply before you start to clean the drive system!
• Disconnect the nine-volt battery if you are using the battery-operated reset function. xxx..
• Never clean the OKIMAT 8 in an automated washing system or with a high-pressure cleaner.
Do not allow fluids to penetrate the unit. Damage to the system could result.
• Do not use a cleanser that contains benzene, alcohol or similar solvents.
• Make sure that you do not damage the drive's connecting cable.
69596(c)
27
Disposal
OKIMAT 8
10. Disposal
10.1
Packaging material
The packaging material should be sorted into recyclable components and then disposed of in accordance with the appropriate national environmental regulations (in Germany according to the recycling law KrWG from 01.06.2012; internationally according to the EU Directive 2008/98/EC
(Waste Framework Directive WFD as of 12.12.2008)).
10.2
Drive components
The OKIMAT 8 drive consists of electronic components, cables and metal and plastic parts. You
should observe all corresponding national and regional environmental regulations when disposing
of the OKIMAT 8 drive.
The disposal of the end product is regulated in Germany by Elektro-G, internationally by the EU Directive 2011/65/EC (RoHS), or by any applicable national laws and regulations. (The end product is
not regulated by the EU Directive 2012/19/EC (WEEE).)
The OKIMAT 8 drive should not be disposed of with normal household waste!
The disposal of the batteries is regulated in the EU by Battery Directive 2006/66/EC, in Germany
by the BattG battery law of 25.6.2009, and internationally by any applicable national laws and regulations.
The nine-volt batteries should not be disposed of with normal household waste!
28
69596(c)
FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)
this device may not cause harmful interference, and
(2)
this device must accept any interference received, including interference that may cause
undesired operation.
Section 15.21 Information to user
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
IC WARNING
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)
this device may not cause interference, and
(2)
this device must accept any interference, including interference that my cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. Lexploitation est autorisée aux deux conditions suivantes:
(1)
l’appareil ne diot pas produire de brouillage, et
(2)
l’utilisateur de lappareil diot accepter tout bouillage radioélectrique subi, méme si le
brouillage est susceptible d’en compromettre le fonctionnement.
Declaration of Incorporation
According to Appendix II of the EU Machinery Directive 2006/42/EC
The manufacturer:
DewertOkin GmbH
Weststraße 1
32278 Kirchlengern
Germany
declares that the incomplete machine described below
OKIMAT 8
complies with the following basic requirements of the Machinery Directive (2006/42/EC):
Sections:
1.1.3; 1.3.3; 1.3.4; 1.3.7; 1.5.1; 1.5.2; 1.5.5; 1.5.6; 1.5.7; 1.5.8;
1.5.9; 1.5.10; 1.5.13; 1.6.3
You may only operate this machine after you have confirmed that the end product (into which this
drive will be installed) complies with the Machinery Directive 2006/42/EC.
On request, the manufacturer is obliged to send the special documentation accompanying the
partially completed machinery electronically to the appropriate national institution. The special
technical documents corresponding to the machine have been created according to Appendix VII,
part B.
The following person is responsible for the technical documentation:
Hans-Joachim Heimsath,
Refer to address listed above.
Tel.: +49(0)5223 979-0
Kirchlengern, Germany. The 15.June 2015
Dr.-Ing. Josef G. Groß
Managing Director
EU Declaration of Conformity
In compliance with Appendix IV of the EU EMC Directive 2004/108/EC
In compliance with Appendix III of the EU Low Voltage Directive 2006/95/EC
In compliance with Appendix VI of the EU RoHS Directive 2011/65/EU
In compliance with Appendix VII of the EU Directive 1999/5/EC (only for the 2.4GHz wireless
version)
The manufacturer:
DewertOkin GmbH
Weststraße 1
32278 Kirchlengern
Germany
declares that the following product
OKIMAT 8
meets the requirements of the following EU directives:
Electromagnetic Compatibility Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
RoHS Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on
the restriction of the use of certain hazardous substances in electrical and electronic
equipment
Radio and Telecommunications Terminal Equipment Directive (1999/5/EC) (only for the 2.4
GHz wireless version)
Applied standards:
EN 60335-1:2012
EN 55014-1/A2:2011
EN 55014-2/A2:2008
EN 61000-3-2/A2:2009
EN 61000-3-3:2013
EN 62233:2008
EN 62479:2010 (only for the 2.4 GHz wireless version)
ETSI EN 300440-2 V1.4.1 (only for the 2.4 GHz wireless version)
This declaration of conformity is no longer valid if constructional changes are made which
significantly change the control unit (i.e., which influence the technical specifications found in the
instructions or the intended use)!
Kirchlengern, Germany. The 15.June 2015
Dr.-Ing. Josef G. Groß
Managing Director
DewertOkin GmbH
Weststrasse 1
Kirchlengern 32278, Germany
Tel: +49(0)5223/979-0
Fax.: +49 0 522375182
http://www.dewertokin.de
Info@dewertokin.de
ID No.: 69595
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Create Date : 2015:06:26 14:56:08+02:00 Modify Date : 2017:03:06 06:37:23+01:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2017:03:06 06:37:23+01:00 Creator Tool : Acrobat PDFMaker 9.1 für Word Document ID : uuid:b6a294e9-de1e-4241-a3b0-10f22f15b1d4 Instance ID : uuid:2b97bc93-be7d-4aae-8a8a-92cd5f60f036 Format : application/pdf Title : Creator : Producer : Adobe PDF Library 9.0 Page Layout : OneColumn Page Count : 35EXIF Metadata provided by EXIF.tools