Digi X2EWIFI ConnectPort X2e Wi-Fi User Manual 90001281 A

Digi International Inc ConnectPort X2e Wi-Fi 90001281 A

Contents

Quick Start Guide

Quick Start GuideConnectPort X2e Wi-Fi Smart EnergyPower SupplyEthernet CableConnectPort X2e Wi-Fi SE 1 Verify Contents2 Write Down the Serial Number®Model: ConnectPort X2e Wi-Fi SEPart Number: 50X2E-Z1C-002-01Serial Number: 00409D50E9BBModel: ConnectPort X2e Wi-Fi SEPart Number: 50X2E-Z1C-002-01Serial Number: 00409D 50E9BB3 Connect HardwarePower ZigBee Network (WAN)Button aConnect the power supplyWrite down the ConnectPort X2e Wi-Fi SE Serial Number:00409D: NOTE: The serial number is also the Ethernet MAC address, which can be used to identify the device during theinstallation process.baConnect the power supplyStartup Sequence - After connecting the power supply, the Power LED will be solid green, the ZigBee LED will be blinking green, and the Network LED (WAN) will be blinking orange.NOTE: Once the Wi-Fi conguration is complete, the Network (WAN) LED will change from blinking orange to solid green.a4 Congure your Device Using the Wi-Fi InterfaceacEnable Access Point mode on your device by pressing the button.bdCongure the Wi-Fi interface of your laptop to connect to the ConnectPort X2e gateway’s access point. The name (SSID) of the access point will be cpx2e-se-xxxxxxxxxx, where xxxxxxxxxxxx is the serial number of the gateway.cc Go to your web browser, and enter the URL of the gateway: http://192.168.100.1NOTE: If the ConnectPortX2e has already been congured to connect to an access point, it will need to be set back to factory defaults to use the following procedure. See the troubleshooting section below to return the gateway back to its initial state. Navigate to Conguration > Wireless Wizard.Follow the steps in the wizard to congure your device.eOnce the conguration is complete, your device will connect to your home access point and attempt to connect to Smartlee. You can track its progress by observing the network LED behavior. Once the connection to your access point and gateway is connected to Smartlee, all the LED’s will be solid green.90001281_A
Network DescriptionStatusNo powerSolid green Device is poweredOFFDescriptionStatusRadio disabledBlinking green (slow) Searching for other ZigBee devices on the networkOFFBlinking green (fast) Establishing a Smart Energy networkSolid green Connected to a Smart Energy network DescriptionStatusPowered OFFBlinking yellow (slow) Powered ON, no Wi-Fi linkOFFBlinking yellow (fast) Wi-Fi link, no IP addressSolid yellow IP address assignedBlinking green (slow) Attempting a connection to SmartleeBlinking green (fast) Smartlee found, authenticatingSolid green Connected to Smartlee© 2012 Digi International, Inc.Digi, Digi International, Inc., ConnectPort, iDigi, and the Digi and iDigi logos are trademarks or registered trademarks of Digi International, Inc., in the United States and other countries worldwide. All other trademarks are the property of their respective owners.Button - The button is intended for advanced conguration or as directed in the online setup. To restart Wi-Fi conguration, hold the button down for 10 seconds to initiate a factory reset. Need Help? Call 1-877-693-7849 or visit www.digi.com/support.6 TroubleshootingPower ZigBee 5 Online Installation Browse to www.livesmartlee.com and follow the step-by-step instructions to completion. 7 Regulatory InformationFor ConnectPort X2e Wi-Fi regulatory information and certications, please refer to the document at the following URL: http://ftp1.digi.com/support/documentation/x2e_wifi_reg.htm

Navigation menu