Digital Cynos DCM-26WT 26" LCD TV User Manual 26WT HY EN

Download:
Mirror Download [FCC.gov]
Document ID	477612
Application ID	z8mUZoUzuOrAhHJeMS1smQ==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	231.26kB (2890805 bits)
Date Submitted	2004-10-11 00:00:00
Date Available	2004-10-11 00:00:00
Creation Date	2004-09-21 18:21:47
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2004-09-22 17:42:56
Document Title	#26WT_HY_EN¹ÌÁÖÇ×
Document Creator	QuarkXPress3.3k: AdobePS 8.5.1
Document Author:	µðÀÚÀγÝ

26” WIDE TFT-LCD TV
ENGLISH
User’s Manual
FCC Information
This equipment has been tested and found to comply with limits for a class B digital device,
Safety Instructions
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
ENGLISH
This equipment can generates, uses, and radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful inteference to radio Communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause unacceptable interference to radio and television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced Radio/ TV technician for help.
Caution : Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Notes & Descriptions
To reduce the risk of fire, electrical shock and other injuries, keep these safety precautions in mind
when installing, using and maintaining your TV.
Warning : If you manipulate against the notice, it may cause serious injury or death to user.
Caution : If you manipulate against the notice, it may cause slight injury to user or appliance.
Ver 1.00NE
EN 2 26” WIDE TFT-LCD TV
Warning
When moving it, do not apply any forces on the set.
Disconnect the power cable and signal cable connected to the product in case
of thunder or lightning.
Do not attempt to disassemble, repair or change the product.
Whenever you need to repair, adjust or check it, refer servicing to qualified
Do not attempt to touch its power cord with wet hands.
service personnel.
ENGLISH
If any electric pin is wet or dusty, remove the moisture or dust first before use.
Do not directly spray water or rub it with inflammable substances (thinner or
It is recommended to pull out the power cord unless you use it for a long time.
benzene) when cleaning it.
Damaged power cord, plug or unfitted outlet may be very dangerous.
Do not wet or penetrate water over/into the set.
When cleaning the LCD surface, disconnect the power and use a piece of
Do not install the set close to any heating sources.
Do not place heavy articles on it or step on the product.
The product should be installed on a clean and dry place.
smooth cloth against any scratches on it. Never use wet cloth.
Caution
Make sure to pull out the power cord when cleaning or removing the product.
Ventilation should be always open and the set should be installed in a wellWhen you detect any smog, unusual noise or smell, just disconnect the electric
power and refer servicing to qualified service personnel.
Do not place any bowl with water, beverage, can or other liquid products on it.
ventilated and wide enough place (a minimum distance away from a wall 10cm
or more).
Do not install the set in a place directly exposed to sunlight.
Do not use or place any combustible sprayer or inflammable substances close
to the product.
Do not arrange the power cord close to any heating devices/sources.
Install the outdoor antenna for the set far away from high voltage cables.
EN 4 26” WIDE TFT-LCD TV
Precautions for Image Ghost
Available Temperature & Humidity
Watching TV in a still image for an excessive time may seriously harm the LCD panel. Note that any
Operating Temperature
0~35˚C
Storage Temperature
-10~50˚C
10~90% RH
Storage Humidity
10~90% RH
1. Digital broadcast is delivered in wide screen
ENGLISH
Operating Humidity
troubles from the reckless use are not guaranteed and please be cautious of the use.
standard (16:9) DTV, so if the existing
broadcasting program made in general screen
For dot defect [dead pixel] of LCD ;
size (4:3) is on the TV, both sides may not be
TFT-LCD produced by using high-end semiconductor technology with precision of 99.9% above is
completely displayed.
used for this TV (2,949,120 pixels).
However the pixels of R.G.B. & White color seem to be right sometimes or some of black pixels
Any different brightness, in case limits to left/right
could be seen on the LCD. This is not from bad quality or functional problem and you can use it
sides are fixed, may leave image ghost of the
without any problem.
limits on the LCD penal, if you watch it for a long
time.
Precautions when used as a PC monitor ;
Since the LCD TV is not designed for a PC monitor, it may not support very high resolutions that
2. When you watch panorama broadcasting in a
are supported in a PC. When you use it for the purpose, refer to the supportable resolution levels
general display, it may show the central image
as follows.
with up/down parts removed.
When used as a PC monitor ;
Any different brightness, in case limits to
Optimal Resolution: 1024 768 @ 60Hz
top/bottom sides are fixed, may leave image
Max. Resolution: 1024 768 @ 85Hz.
ghost of the limits on the LCD penal, if you watch
it for a long time.
3. Watching the screen in a still image for a long
time may leave image ghost on the LCD panel.
EN 6 26” WIDE TFT-LCD TV
Contents
Before Use
1-1. Accessories
CHAPTER 2.
EN 8 26” WIDE TFT-LCD TV
CHAPTER 3.
ENGLISH
CHAPTER 1.
Using TV Menus
12
3-1. Watching TV
1-2. Panels
13
3-2. Auto On/Off Timer
35
1-3. Remote Control
16
3-3. Change TV Channel Mode
37
1-4. MENU Configuration
18
3-4. Channel Search & Fine Tune
38
1-5. Jog Shuttle Button
20
3-5. Add/Remove Channel
40
1-6. Inserting the Batteries in the Remote Control
21
3-6. Channel Swap
41
3-7. Password
42
Connection
32
3-8. Channel Lock
43
3-9. Caption
45
2-1. Connecting Power
24
3-10. V-chip Funetion
46
2-2. Connecting TV Antenna
24
3-11. DTV Field
48
2-3. Connecting PC
25
3-12. Stereo
49
2-4. Connecting PC DVI
25
3-13. Bilingual (Multi-Language Broadcasting)
49
2-5. Connecting DTV
26
2-6. Connecting DVD
27
2-7. Connecting VIDEO / S-VHS Input
28
2-8. Connecting Headphone (speaker) Output
29
Using Menus of Picture,
Sound and Others
2-9. Connecting VIDEO Output
30
4-1. Setting Display Mode
52
4-2. Setting Scale Mode
54
4-3. Setting Picture Mode
55
4-4. Setting Simultaneous Picture Mode
58
CHAPTER 4.
4-5. Setting Screen MENU by Simultaneous Picture
61
4-6. Setting Sound
64
4-7. Setting Others
66
Contents
CHAPTER 1
CHAPTER 5.
CHAPTER 6.
CHAPTER 7.
EN 10 26” WIDE TFT-LCD TV
ENGLISH
Before use
1-1. Accessories
Using PC MENU
1-2. Panels
5-1. Auto Adjustment
70
1-3. Remote Control
5-2. Setting PC Scale Mode
72
1-4. MENU Configuration
5-3. Setting Phase/Frequency
73
1-5. Jog Shuttle Button
5-4. Setting Position/Size
74
1-6. Inserting the Batteries in the Remote Control
Specifications
6-1. Dimensions
78
6-2. Specifications
79
Services & Others
7-1. Troubleshooting
82
7-2. Concerning Services
84
11
1-1. Accessories
1-2. Panels
Please make sure the following items are included with your LCD TV.
Front Panels
If any items are missing, contact your dealer.
ENGLISH
AAA-type battery( 2)
User’s Manual
-2
-1
DC 15V Adaptor
-4
-5
-3
RF Cable
Remote Control
D-Sub Cable
Power/MENU
-1. Power-On/Off
Channel Button
-2. AUTO / Move above MENU
Sound Cont. / MENU SET
-3. SOURCE / Move under MENU
Remote Control Sensor
-4. Exit MENU
LED
-5. Load MENU
AUTO button searches automatically TV channels if set as TV, and it adjusts
automatically for PC mode.
Power button is jog shuttle type button and it operates different functions by pushing it
to Up/Down/Left/Right.
EN 12 26” WIDE TFT-LCD TV
13
Rear Panels
Side Panels
ENGLISH
Video/Audio Input
Power Input
DVI Input
S-VHS Input
PC Input
PC Sound Input
Headphone Output
DTV Input (Y Pb Pr LR)
DVI Input (Y Pb Pr LR)
Video/Audio Output
TV Antenna Input
EN 14 26” WIDE TFT-LCD TV
Upgrade (Only for service personnel)
15
1-3. Remote Control
Functions by remote control buttons
Button
Channel Selection Button
Display Selection Button
Display Mode & Audio Control Button
MENU Control Button
Channel & Volume Control Button
TV Functions & Teletext Menu Button
PIP Function and Setting Button
Button
Function
Power On/Off
MUTE
Sound off Temporarily
VIDEO
Composite Video Input
S-VHS
S-Video Input
DVD
DVD Input (Y PbPr)
TV
TV Input
RGB
PC Input
DVI
DVI Input (Optional)
COMP
DTV Component Input
DTV (TV2)
PIP TV Input (Optional) / DTV Input (If DTV Tuner is built in)
NORMAL
Select Normal Display
PIP
PIP display
SPLIT
Split (PBP)
TV SCAN
16 Channels Multi Scan
0~9
Numeric Buttons
PRE
Previous Channel
ENT
Input selected channels
LIGHT
Control background Light
PICTURE
Control Picture Mode
SOUND
Control Sound
SCALE
Control Picture Scale
FREEZE
Pause
ON SCREEN
Display screen status
MENU
Enter Main/Sub MENU
EXIT
Exit Main/Sub MENU
ENGLISH
TV & Input Source Selection Button
Function
POWER
CH UP / DOWN Move TV channels / Move MENU up and down
VOL + / -
Control Volume / MENU settings
CAPTION
Turn On/Off Caption
MEM
Add/Remove a TV CH
TUNE
Finely adjust TV Channel
SWAP
Switch TV channels
CATV
TV Mode
Zoom ON
Zooming On/Off
IN
Zoom in
OUT
Zoom out
AUTO
TV : Channel search / PC : Auto Adjustment
SURROUND
Surround effect
BILINGUAL
Select Multilanguage broadcasting system
EPG
Electronic Program Guide
STEREO
STEREO/MONO
SLEEP
Sleep TImer setting
(Option for DTV)
WAKE UP
SET UP
Other setting
PIP SOURCE PIP input signal change
PIP VIDEO
Switch Main/PIP screen
PIP AUDIO
Switch Main/PIP sound
PIP POSITION
Change PIP position
PIP SIZE
Control PIP size
Wake-Up Timer setting
PIP CH UP / DOWN Change PIP TV Channel
The remote control provided is available up to 7m from the optical receive part within Left/Right
15 degrees.
EN 16 26” WIDE TFT-LCD TV
17
1-4. MENU Configuration
2. Press it again to move to sub menu of a selected main
menu.
Most functions of the TV set can be controlled by MENU and selection buttons on the
remote control, so learning how to operate them would be convenient for you.
1) Press MENU button to display main menu.
1. Menu Configuration
ENGLISH
2) Press it again to move to sub menu of a selected main menu.
Sub Menu
Main Menu
3) Press
EXIT
to return from sub menu to main menu or from
main menu to menu removal.
4) To move among menus, use CH button.
5) To change a selected menu setting, use VOL button.
Settings
EN 18 26” WIDE TFT-LCD TV
19
1-5. Jog Shuttle Button
1-6. Inserting the Batteries in the
Remote Control
1) Push MENU button right to display main menu.
1) Remove the cover of the remote control.
ENGLISH
2) Check the polarity of batteries and insert them in right directions.
3) Replace the cover.
2) Push it right again to display sub menu.
4) Available batteries : 2 DC 1.5V AAA-type batteries
Since incorrect insertion of batteries may cause breakage, leakage or injuries, check
3) Push MENU button left to return to main menu.
the polarities before the insertion.
Separate and collect used batteries for the protection of environment.
Do not use alkaline and manganese batteries together.
4) Push it left again to clear menu.
5) Push the button up and down to move among menus.
If pushing it upward when menu is not displayed, it
controls TV channel search or automatic PC settings.
If pushing it downward when menu is not display, it
changes input signals.
6) Change menu settings by using left/right
directional buttons.
EN 20 26” WIDE TFT-LCD TV
21
CHAPTER 2
ENGLISH
Connection
2-1. Connecting Power
2-2. Connecting TV Antenna
2-3. Connecting PC
2-4. Connecting PC DVI
2-5. Connecting DTV
2-6. Connecting DVD
2-7. Connecting VIDEO / S-VHS Input
2-8. Connecting Headphone (speaker) Output
2-9. Connecting VIDEO Output
EN 22 26” WIDE TFT-LCD TV
23
2-1. Connecting Power
2-3. Connecting PC
1. The product automatically adjusts voltage.
In case 110V is used, connect 110V Conversion adaptor before use.
2. Power Cable should be firmly connected to an outlet or DC adaptor in order not to
be pulled out or shake.
ENGLISH
2-2. Connecting TV Antenna
1. When round cable (75Ω coaxial cable) is used, copper part of the cable should not
be bent.
1. Connect D-Sub Cable to D-Sub port on the TV and PC.
2. Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC
Audio Input Port of the TV (stereo jack).
TV antenna
TV Wall-outlet
RF cable
Connecting RF
cable
2-4. Connecting PC DVI
copper wire
Antenna converter
Connecting
feeder cable
feeder cable
TV Wall-outlet
Cautions
1. When an outdoor antenna is used, it is recommended for a skilled technician to install it.
2. It may be helpful to better display to purchase additional installing amplifier if there is any
problem with weak radio wave.
1. Connect DVI Cable (not included) to DVI port of the TV and PC.
2. Connect Audio Cable (not included) to Audio port of PC (stereo jack) and TV (stereo
jack).
3. It is recommended to use D-type DVI cable.
EN 24 26” WIDE TFT-LCD TV
25
2-5. Connecting DTV
2-6. Connecting DVD (Y Pb Pr)
Digital TV Broadcasting Receiver
PB
PR
PB
PR
L AUDIO R
1. Connect Component Cable (not included) to DTV Connection ports of TV (Y Pb Pr)
and DTV Receiver.
2. Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV Receiver.
PB
PR
PB
PR
ENGLISH
DVD Playe
L AUDIO R
1. Connect Component Cable (not included) to Component ports of TV and DVD
player. VCR, Set-Top box or camcorder.
2. It supports 480i.
3. Cables should be connected to ports of same colors.
4. Set the video output of a DTV Receiver as 480p, 720p.
EN 26 26” WIDE TFT-LCD TV
27
2-7. Connecting VIDEO / S-VHS Input
2-8. Connecting Headphone (speaker)
Output
VCR/DVD Player and etc
ENGLISH
Audio Output/Video Output/S-VHS Output
1. Connect Headphone (not included) to the Headphone output port of the TV.
2. Even in case of using headphone, internal speakers built in the TV still works and if
1. Connect Video/Audio Cable (not included) and S-VHS Cable to Video port of TV and
camcorder, game machines, VCR, DVD player or Set-Top box.
2. Cables should be connected to ports of same colors.
3. Audio signals of S-VHS should be used with external audio signal cables.
4. S-VHS signal secures better quality than composite video signal.
you press MUTE button, the speakers stop working.
3. If possible, use the headphones of which impedance is 8Ω. Other headphones may
output too weakly or strongly.
4. In case of connecting to speakers, connect speakers with amps. If connected with
speakers without amps, it may sound weakly.
5. In case of headphone output, volume is not controlled.
EN 28 26” WIDE TFT-LCD TV
29
2-9. Connecting VIDEO Output
CHAPTER 3
ENGLISH
Using TV Menus
3-1. Watching TV
3-2. Auto On/Off Timer
3-3. Change TV Channel Mode
3-4. Channel Search & Fine Tune
3-5. Add/Remove Channel
3-6. Channel Swap
3-7. Password
3-8. Channel Lock
1. When recording TV program or using the video/audio of the TV for other AV device
3-9. Caption
(VCR and etc), connect it to AUX Output terminal of the TV and Input Port of the
3-10. V-chip Funetion
device.
3-11. DTV Field
2. Cables should be connected to terminals of same colors.
3-12. Stereo
3. External Output Signal outputs TV broadcasting signals of the main display.
3-13. Bilingual (Multi-Language Broadcasting)
EN 30 26” WIDE TFT-LCD TV
31
3. Channel Selection
3-1. Watching TV
1) Press CH button on the remote control to change channels.
1. Precautions in the initial installation
2) Press numeric buttons to go to a channel directly.
3) Press CH buttons (
) on the TV set to increase or decrease TV channels.
1) Check whether TV antenna cable is properly connected.
ENGLISH
2) After checking whether the voltage is 100V or 220V, supply the electric power and
connect the adaptor to the TV.
At the moment, TV is in standby.
2. Turning on TV
Channel button on the remote control
Channel button on the TV set
1) Turn on the Power button directly on the set or by remote control.
2) Each pressing the button turns on or off the set.
4. Volume Control
1) Increase/decrease volume by pressing VOL button on the remote control.
2) Press VOL button (< / > ) on the TV set to control the volume.
Power Button on Remote Control
Power Button on the TV Set
Volume Button on the remote control
EN 32 26” WIDE TFT-LCD TV
Volume Button on the TV Set
33
5. Mute
3-2. Auto On/Off Timer
1) Press
MUTE
button on the remote control to
You may set the TV to turn on or off in a certain time period.
sound off temporarily and “MUTE” is displayed.
2) Press it again to turn the sound back on or press
1. Setting Wake-Up Timer
volume buttons.
MENU
button on the remote control.
ENGLISH
- Press
MUTE button on the remote control
- Set the time to turn on the TV automatically by using volume button on the remote
control.
- Wake-up timer can be set from Off to 12 hours.
6. Move to Previous Channel
- Once the setting is complete, press EXIT button.
1) Every time pressing the
PRE
button on the
remote control, it moves to a previous channel.
Previous Channel Button
7. Checking the present broadcasting information
1) Press ON SCREEN button on the remote control
to display the information on the screen.
2) Press
ON SCREEN
button again removes the
information or leaving it clears the information in 5
Broadcasting Info Button
seconds.
In case of TV Signal, it displays channel info while it shows mode info in case of PC signal.
EN 34 26” WIDE TFT-LCD TV
35
2. Setting Sleep Timer
3-3. Change TV Channel Mode
- Press MENU button on the remote control.
Please set your broadcast type between Air and Cable.
- Set the sleep timer by using volume button on the remote control.
If its mode is set as Air, some Cable broadcasts are not able to watch.
- Sleep Timer can be set from Off to 180 minutes.
- Once the setting is complete, press EXIT button.
CH Mode
Cable
ENGLISH
Air
- Press CATV button on the remote control.
SCREEN
Auto Scan
PICTURE
CH Fine Tune
TV
CH Memory
PC
CH Swap
SOUND
CH Mode
OPTION
CH Mode
Air
Cable
- Set the CH Mode between Air & Cable by using Volume button on the remote
control.
- Once the setting is complete, press CATV button or EXIT button.
- Also, it can be set in OSD menu if JOG button is used.
EN 36 26” WIDE TFT-LCD TV
37
3-4. Channel Search & Fine Tune
2. Fine Tuning Channel Reception
When using the TV first after purchase, reconnecting it due to power failure or other
If a searched channel is unclear or sounds abnormally, use Fine Tune function.
reasons, channels should be searched and registered again.
- Press MENU button on the remote control to move to Fine Tune Menu.
Since Channel Search function searches channels currently broadcasted, you should
execute it when most channels are broadcasted.
ENGLISH
1. Channel Search
- Press MENU button on the remote control.
- If controlling menu settings left or right by using Volume button on the remote control,
it searches the optimal status.
- Once the setting is complete, press TUNE button again or EXIT button.
- Also, it can be set in OSD menu if JOG button is used.
- Once you move to START by using Volume button on the remote control, it starts
channel search.
- To stop channel search, repress
EXIT
button on the remoter control.
- If you stop it during channel search, it stores the currently searched channels only.
- Also, it can be set in OSD menu if JOG button is used.
EN 38 26” WIDE TFT-LCD TV
39
3-5. Add/Remove Channel
3-6. Channel Swap
You may add or remove a channel as your need.
In case of channels frequently watch, you can switch it to other channel numbers and
- Move to a channel to add or remove by pressing numeric buttons or CH button.
store them.
- Press MENU button on the remote control.
- Move to a channel to change.
- Press MENU button on the remote control.
ENGLISH
- In case of adding a channel by using Volume button on the remote control, move to
Add or Remove.
- Once the setting is complete, press EXIT button again or EXIT button.
EN 40 26” WIDE TFT-LCD TV
- Change a channel number to switch by using Volume button on the remote control.
- Once the setting is complete, press EXIT button.
41
3-7. Password
3-8.Channel Lock
When using Contents Blocking function, you can set password and please keep the
You can make some channels to prohibit to watch by Channel Lock function.
password private.
It can be set only by remote control.
Default password is <0000>.
Please change default password to new one after installing TV.
- Press SET UP button on the remote control.
ENGLISH
- Move to CH Lock menu by using MENU button on the remote control.
- Press SET UP button on the remote control.
- Move to password menu by using
MENU
and
CH
button on the
remote control
- Enter your password by using the remote control.
- Press MENU button on the remote control for entering Password setting menu.
- When setting password first after purchase, press <0000> on the remote control and
press
ENT
or
MENU
on the remote control after entering new password for
changing.
- Set TV broadcast mode by using
- Press new password and
EN 42 26” WIDE TFT-LCD TV
ENT
VOL
button on the remote control.
or MENU again for confirmation it.
43
- Move to the channel which you want to prohibit by using MENU and
VOL
- Press
3-9.Caption
button.
ENT
- If you press
or MENU button for setting it.
ENT
or MENU again, it will be cancelled.
- It displays different color for CH Lock channel.
This function works only Caption broadcast or other CC marked video tape and DVD title.
Set the function in the SETUP menu.
Caption can be set only by using the remote control.
- Press
CAPTION
ENGLISH
1. Caption On / Off
button on the remote control when it is
broadcasted.
- Press CAPTION button for coming out from setting.
2. Set Caption
- Press SETUP button.
- Move to Closed Caption menu by using
CH
button.
- Press EXIT for coming out from setting.
- Set Caption broadcast type by using VOL button on the remote control.
- Press EXIT button for coming out from setting.
EN 44 26” WIDE TFT-LCD TV
45
3-10. V-Chip Funetion
- Move to TV Guideline or MPAA Rating by using
CH
button on the
remote control.
It makes MPAA rating of TV broadcast and other media.
It works only with V-Chip function broadcast and media.
It can be controlled by using the remote control only.
- Move to the position which you want to make channel blocking and
press
ENT
or MENU button for setting.
- Press it again for cancellation.
ENGLISH
- Press SETUP button on the remote control.
- Move to V-Chip menu by using
CH
button on the remote control.
- Press MENU button and enter Password.
- Press
ENT
or MENU button on the remote control.
- Set V-Chip function by using
VOL
button on the remote control.
- Press EXIT button for coming out from setting.
EN 46 26” WIDE TFT-LCD TV
47
3-11. DTV Field
3-12. Stereo
Depending on a DTV receiver, a signal is not identical with standard signal. It may
If you use the TV in an area with weak or bad reception, there may cause sound noise
cause unclear display and if you change DTV Field value, it will be recovered to the
or other problem when selecting a channel. In this case, cancel the STEREO setting.
normal picture (it can be set only by the remote control).
It can be canceled only by the remote control.
ENGLISH
- Press SET UP button.
- Press STEREO button on the remote control to cancel stereo and
returning to Mono.
- Press STEREO button in Mono returns to Stereo.
- If Stereo is off, it is always set as Mono even though a channel is
changed.
- Press MENU button to go into DTV Field Setting Menus.
- Set Not Invert/Invert with Volume button.
- Initially, ‘Not Invert’ is defaulted and you may change it to ‘Invert’ if the
display is not normal.
3-13. Bilingual
(Multi-Language Broadcasting)
In case of multi-language broadcasting, it can be converted if you wish to listen to
other language except main language.
Multilanguage broadcasting can be set only by the remote control.
- Every time pressing BILINGUAL button on the remote control, the
language display is changed in good order of main language
- Once the setting is complete, press the EXIT button.
language
sub
main + sub languages (dual language).
(Main - Sub - Dual)
EN 48 26” WIDE TFT-LCD TV
49
CHAPTER 4
ENGLISH
Using Menus of
Picture, Sound and
Others
4-1. Setting Display Mode
4-2. Setting Scale Mode
4-3. Setting Picture Mode
4-4. Using Simultaneous Picture Mode
4-5. Setting Screen MENU by Simultaneous Picture
4-6. Setting Sound
4-7. Setting Others
EN 50 26” WIDE TFT-LCD TV
51
4-1. Setting Display Mode
4) SPLIT FULL : Repressing
SPLIT
button in Split display, shows main screen and
sub screen in split full screen.
You may view other video screen while watching TV.
- Press NORMAL , PIP , SPLIT or TV SCAN button.
ENGLISH
1) NORMAL : Show a selected main screen in full size.
5) TV SCAN : Show 16 channels searched and stored in the TV set in 16 pictures in
order on the screen. At the moment, TV SCAN can be operated only by the remote
control.
2) PIP : Show main screen and sub screen in full size and small
size together.
- Also, it can be set in OSD menu if JOG button is used.
- OSD Menu is different depending on Display Type [Screen Layout].
3) SPLIT : Show main screen and sub screen by horizontally
shared. You can control Main screen’s (left side screen) size
and Sub screen’s size is controlled inverse ratio of main screen.
EN 52 26” WIDE TFT-LCD TV
53
4-2. Setting Scale Mode
4-3. Setting Picture Mode
You can set the screen’s suitable image scale of TV or Video input signals and view
By setting a picture mode suitable for broadcasting/video signals, you may enjoy
them accordingly.
better quality picture.
- Press SCALE button on the remote control.
- Press PICTURE button on the remote control.
ENGLISH
- Control the scale in desirable size by using
VOL
button on the remote control.
- Set a picture mode by using Volume button on the remote control.
1) FULL : Show a screen in the full LCD Penal.
1) Standard : Standard picture mode.
2) 16:9 : Show a screen in 16:9 wide screen size.
2) Soft : It displays a picture softly as a whole and is better for watching a film or TV
3) 4:3 : Show a screen in 4:3 screen size for general broadcasting.
series.
4) CAPTION : Show a screen suitable for Caption Broadcasting.
3) Dynamic : The mode is suitable for watching sports, which changes pictures fast.
5) SMART VIEW : Show a screen in a proportion suitable for grand image.
4) User : It is a picture mode customized by a user.
In PIP or SPLIT screen, it can be set in types of AUTO, 16:9, 4:3. For more
- Also, it can be set in OSD menu if JOG button is used.
information, see to 4-4 Setting Simultaneous Picture Mode.
- Once the setting is complete, press PICTURE button or
EXIT
button on the
remote control.
- Also, it can be set in OSD menu if JOG button is used.
- OSD Menu is different depending on Display Type [Screen Layout].
EN 54 26” WIDE TFT-LCD TV
55
1. Setting USER Mode
2. Setting Room Light
You can set each picture mode according to your taste. If you set USER mode as your
You can adjust the entire TV brightness according to lightning status.
taste, it is stored as USER Mode standard.
- Press MENU button on the remote control.
- Adjust values by using Volume button on the remote control.
- Press MENU button on the remote control and move to PICTURE of
- Once the setting is complete, press EXIT button on the remote control.
ENGLISH
main menu by using CH button on the remote control.
- Press
MENU
button on the remote control and move to the sub
menu for changing values by using CH / VOL buttons.
1) Brightness : Adjust screen brightness.
2) Contrast : Adjust screen contrast.
3) Color : Adjust screen color.
4) Sharpness : Adjust screen sharpness.
5) Room Light : Adjust the brightness of TV screen according to background
brightness.
EN 56 26” WIDE TFT-LCD TV
57
4-4. Setting Simultaneous Picture Mode
3. Changing Sub Screen Size
It adjusts sub screen size.
While watching TV on main screen, you can enjoy other video picture on the sub
screen.
- Press PIP SIZE button on the remote control.
- Adjust sub screen size by Volume button on the remote control.
Simultaneous Picture means PIP and/or SPLIT Picture display.
- Different menus are displayed depending on PIP Picture or SPLIT
Picture.
ENGLISH
1. Changing a channel of Simultaneous Picture
- Press PIP CH button on the remote control.
- It changes a TV channel if the sub screen shows TV.
2. Changing input signal of Sub-Screen
- On PIP Picture, sub screen size can be adjusted from 1/16 to 1/4 of the full size.
- Press PIP SOURCE button on the remote control.
- Every time pressing PIP SOURCE button, it changes input signal of
sub screen.
- Available input signals of sub screen are as follows;
SUB
PC
PC
RGB
DVI
PC RGB
PC DVI
COMP
TV1
TV2
VIDEO
S-VHS
TV1
TV2
VIDEO
MAINRGB
(DTV)
DVD
S-VHS
COMP (DTV)
DVD
EN 58 26” WIDE TFT-LCD TV
- On SPLIT Picture, main screen size is adjusted while sub screen size is adjusted
accordingly.
- On SPLIT Picture, the left screen always shows main screen.
59
4. Changing Sub Screen Position
Adjust a sub screen’s position on PIP Picture.
- Press PIP POSITION button on the remote control.
4-5. Setting Screen MENU by
Simultaneous Picture
Depending on Layout in OSD Menu, sub menus of SCREEN are changed.
- Move PIP picture to a desirable position by using CH / VOL button
on the remote control.
ENGLISH
1. SCREEN MENU in NORMAL Picture
- It works only in NORMAL Picture.
- Select SCREEN menu by pressing MENU button on the remote control (MENU
- The position is set as USER setting of OSD menu.
MENU).
- Once the setting is complete, press PIP POSITION or EXIT button on
the remote control.
5. Switching Main/Sub Screen
It switches main/sub screens.
In case of switching main/sub screens, audio is changed accordingly.
The left screen always shows main screen.
6. Switching Audio of Main/Sub Screen
It switches audio of main/sub screen.
1) Layout : Set Picture mode [Display Mode].
In case of switching audio of main/sub screen, it switches audio only,
2) Image Scale : Select an image scale
not screens.
(FULL, 16:9, 4:3, Caption, Smart View)
- Once the setting is complete, press EXIT button to exit it.
EN 60 26” WIDE TFT-LCD TV
61
3. SCREEN Menu in SPLIT Picture
- It works only on PIP Picture.
- It works only on SPLIT Picture.
- Select SCREEN menu by pressing MENU button on the remote control.
- Select SCREEN menu by pressing MENU button on the remote control.
1) Layout : Set a display layout.
1) Layout : Set a display layout
2) Image Scale : Select an image scale of main screen.
2) Split Size : Adjust a size of Split main screen. Sub screen size is adjusted by main
ENGLISH
2. Screen Menu on PIP Picture
(FULL, 16:9, 4:3, Caption, Smart View)
3) PIP Position : Adjust the position of PIP
(L-Top, L-Bottom, R-Top, R-Bottom, USER)
4) PIP Position X / Y : In case of PIP Position menu is set as USER, it sets X/Y
position of PIP.
screen size.
3) SPLIT Scale : Adjust an image scale of SPLIT Picture.
- Auto : Adjust PIP scale by automatically determining input signals.
- 16:9 : It fixes PIP sub screen scale to 16:9.
- 4:3 : It fixes PIP sub screen scale to 4:3.
5) PIP Size : Adjust PIP size. It can be adjusted from 1/16 to 1/4 of full screen.
6) PIP Scale : Adjust image scales of PIP.
- Auto : Adjust PIP scale by automatically determining input signals.
- 16:9 : It fixes PIP scale to 16:9.
- 4:3 : It fixes PIP scale to 4:3.
EN 62 26” WIDE TFT-LCD TV
63
4-6. Setting Sound
2. USER Mode Setting
USER mode can be set only in OSD menu.
You can set sound suitable for TV broadcasting or Video.
- Press MENU button to go into main menu.
- Move to SOUND menu by using CH button.
1. Mode Setting
- Press MENU button to move to the Sub Menu.
- Press SOUND button on the remote control to display SOUND mode setting.
- Adjust sound in a desirable frequency bandwidth by using VOL
ENGLISH
/ CH button on the remote control.
3. SURROUND Setting
- Set the menu settings by using Volume button on the remote control.
Surround mode can be set only by the remote control.
1) Standard : Standard sound mode.
- Press SURROUND button on the remote control.
2) Music : Music broadcasting mode.
- Set ON/OFF by using Volume button on the remote control.
3) Movie : Cinema broadcasting mode.
4) News : News broadcasting mode.
5) User : User’s customization mode.
Also, it can be set in OSD menu if JOG button is used.
- Once the setting is complete, press SURROUND or EXIT button on the remote
control.
Balance : Control the balance of Left/Right speakers.
EN 64 26” WIDE TFT-LCD TV
65
4-7. Setting Others
2. Setting OSD Menu Language
Change a language to display OSD.
Press MENU button on the remote control to move to Main Menu.
ENGLISH
Move to OPTION menu by using CH button on the remote control
Press MENU button to move to the Main menu.
Change the settings by using VOL / CH button on the remote control.
3. Factory Reset
Reset all the OSD control settings back to the factory setting status.
1. Menu Timeout Setting
It can be adjusted to display OSD Menu between 5 ~ 60 seconds.
EN 66 26” WIDE TFT-LCD TV
67
4. Version
It shows the product version.
CHAPTER 5
ENGLISH
Using PC MENU
5-1. Auto Adjustment
5-2. Setting PC Scale Mode
5-3. Setting Phase / Frequency
5-4. Setting Position / Size
EN 68 26” WIDE TFT-LCD TV
69
5-1. Auto Adjustment
In case of using it as a PC monitor, it is automatically set.
The Standard Signal Modes for PC Monitor
Resolution
(H
When the set is connected to a PC, the MODE should be set as PC RGB Mode.
- Press
MENU
button on the remote control to automatically set the product’s
screen status.
V)
Vertical Frequency Horizontal Frequency Clock Frequency
(kHz)
(Hz)
(MHz)
Polarity
(Vert./Hor.)
480
31.469
59.94
25.175
-/-
640
480
37.861
72.809
31.5
-/-
640
480
37.5
75
31.5
-/-
720
400
31.469
70.087
28.322
-/+
800
600
37.879
60.317
40
+/+
800
600
48.077
72.188
50
+/+
800
600
46.875
75
49.5
+/+
1024
768
48.363
60.069
65
-/-
1024
768
56.476
70.069
75
-/-
768 (Optimal)
60.023
75.029
78.75
+/+
1024
ENGLISH
640
When you use it as a PC monitor, depending on signals of a PC, it may not display
- Move to START by using Volume button on the remote control to start Auto
picture normally even though it is set for standard mode resolution.
Adjustment.
When it is used as a PC monitor;
Optimal Resolution: 1024 x 768 @ 60Hz
Max. Resolution: 1024 x 768 @ 85Hz.
- It may not normally display picture in any resolution out of the optimal resolution
range.
- When you use it as a PC monitor, it requires to be set the Standard Signal Mode for
PC Monitor before use.
- Even though it is automatically adjusted, it may not normally display picture
depending on signals from a PC and in this case, it is recommended to execute Auto
Adjustment for several times.
EN 70 26” WIDE TFT-LCD TV
71
5-2. Setting PC Scale Mode
5-3. Setting Phase / Frequency
When being used as a PC Monitor, the scale can be adjusted.
In case it is not optimally set even though automatically adjusting it, use PHASE
PC Monitor Scale works only when PC signal is connected and input signals are
function.
selected in RGB mode.
- Press MENU button on the remote control.
- Press SCALE button on the remote control.
- Move to PC menu by using CH button.
ENGLISH
- Move to PHASE menu by pressing MENU button.
- Adjust settings by controlling Volume button.
- Once the setting is complete, press EXIT button.
- Select a desirable scale by using Volume button.
- Once the setting is complete, press EXIT button.
1. 1:1 : Display the resolution as 1:1.
2. Fill All : Display picture in the full screen regardless of the resolution.
3. Aspect Ratio : Display the resolution in 4:3 aspect ratio. Also, it can be set in OSD
menu if JOG button is used.
EN 72 26” WIDE TFT-LCD TV
73
5-4. Setting Position / Size
(1) Setting Vertical/Horizontal Size
- Press MENU button on the remote control.
Adjust the position and size of the PC Monitor.
- Move to PC Menu by using CH button.
- Move to H / V Size Menu by using MENU button.
- Adjust settings by controlling Volume button.
1. Setting Vertical/Horizontal Position
- Once the setting is complete, press EXIT button.
ENGLISH
- Press MENU button on the remote control.
- Move to PC Menu by using CH
button.
- Move to H / V Position Menu by using MENU button.
- Adjust settings by controlling
VOL
button.
- Once the setting is complete, press EXIT button.
EN 74 26” WIDE TFT-LCD TV
75
CHAPTER 6
ENGLISH
Specifications
6-1. Dimensions
6-2. Specifications
EN 76 26” WIDE TFT-LCD TV
77
6-1.Dimentions
6-2. Specifications
Dimensions, apparent design and specifications are subject to change without any
86mm
660mm
prior notice for the performance improvement.
26” WIDE TFT-LCD TV
LCD Panel
Type
Amorphos Silicon TFT-LCD
Size
26” Wide (diagonal length)
480mm
520mm
393mm
228mm
Pixel Pitch
0.4425 mm x 0.4425 mm
Contrast Ratio
500 : 1 (Typ.)
Brightness
500 cd /
Actual Display Size
372.48 mm (H) x 223.49 mm (V)
Viewing Angle
L/R: 88°/ 88° U/D: 88°/ 88°
Interface
LVDS
TV Channel

ENGLISH
Product Name
VHF: 2~13 channels UHF: 14~69 channels
Cable: 1, 14~125 channels
423.3mm
TV Broadcasting System
PAL / SECAM , NTSC-M Type
Audio Output
MAX 20W + 2 / Stereo
PC Monitor
M4 6mm, 4 points
223mm
Horizontal Frequency
30 ~ 61 kHz
Vertical Frequency
56~ 85 Hz
Colors
16.7M colors (8bit)
Max. Resolution
XGA : 1024 (H) x 768 (V)
Other Resolutions
XGA, SVGA, VGA
Power
Adaptor Input
AC 100V~240V, 50~60Hz
Adaptor Output
DC 15 V
Power Consumption
In-Operation
< 120W
Power-Saving Mode/OFF < 5W
Energy Saving Mode
VESA DPMS
Weight : approx. 19kg (before packing) / approx. 22kg (after packing)
EN 78 26” WIDE TFT-LCD TV
79
CHAPTER 7
ENGLISH
Service & Others
7-1. Troubleshooting
7-2. Concerning Services
EN 80 26” WIDE TFT-LCD TV
81
7-1. Troubleshooting
2. PC Monitor-related Troubles
Before contacting service to service personnel, please check the followings first.
No image on the monitor
If you still have the same symptoms even after taking the following actions, contact
Check whether the D-Sub cable is firmly connected to the TV and a PC.
your local dealer or qualified service personnel.
Check whether a graphic card is correctly inserted into the slot.
Check whether the Power of a PC and the TV is on.
Check whether a graphic card or mode is set appropriately on a PC.
ENGLISH
1. TV-related Troubles
Referring to the Standard Signal Mode for PC Monitor in the previous chapter,
Unclear display or noisy sound
Check whether TV antenna is correctly connected.
change graphic mode.
Check whether D-Sub cable pins are not inserted or bent.
Broadcasting may not be good in an area with bad reception or far away from a
station/network.
No Power
Check whether the power cord is normally inserted and reconnect it.
No image
Pull out the power cord from wall outlet and reconnect it in 10~20 minutes.
Check whether you connect the power cord properly. And press the POWER button.
LED Lamp turns off in red and it shows no image
Black background only
Check whether the mode is set as PC monitor or Video/S-VHS Input, not TV mode.
Check whether the graphic cable is connected to theTV and a PC.
Check whether a computer is in power-saving mode and attempt to operate
keyboard and mouse.
Strips and shaking display
It may be interrupted by neighboring radio waves (please check any wireless phone,
hair drier, electric drilling machine and etc)
Execute fine tuning for manual adjustment.
Unstable or unfocused image or trembling
Check whether the D-Sub cable is connected to the TV and a PC.
If a PC’s display mode is changed, the screen needs readjusting, so you need to
use Auto Adjustment or Picture Adjustment.
Can’t catch a specific channel
Check whether Channel Setting is normally set.
Try to rotate an antenna’s direction.
Picture plays without sound
Try to press MUTE button.
Volume up by using Volume button.
Check whether the TV and your graphic card are compatible each other and
whether it is set as an appropriate refresh rate. If letters look distorted, change the
refresh rate to 60Hz.
Abnormal image scale
By using vertical/horizontal position in Picture Adjustment Menus, adjust the
position.
Try to execute Auto Adjustment function.
EN 82 26” WIDE TFT-LCD TV
83
7-2. Concerning Services
We guarantee free of charge After-sales service for a full year if any troubles are found
when you are using our product. However, any natural disasters or careless use cause
the trouble, it may cost even within a valid warranty period.
Responsibility of Chargeable After Sales Service (Customer’s Charge)
In one of the following cases, it may cost even in the valid warranty period.
1. In case of any troubles resulting from inserting of foreign substances (water,
beverage, coffee and etc)
2. Dropping or applying force cause a trouble to damage on the product or induce
malfunction.
3. Appearance damage or transformation by use of organic solutions such as thinner,
benzene and etc.
4. When it gets troubled due to your disassemble.
5. When other parts/consumption accessories (including adaptor) that are not supplied
by the company may directly cause any troubles.
6. Supplying wrong voltage may cause a trouble
7. Any personnel not from qualified service personnel repairs or modifies the product,
resulting in troubles.
8. Natural disasters (lightning, fire, flood, gas, damage from sea wind, earthquake and
etc) directly cause troubles
9. Violation against the directions in the manual cause any troubles
10. Customer’s mishandling cause a trouble
11. In case the date of purchase may be vague, the valid warranty period is counted
after 2 months since the product is manufactured.
EN 84 26” WIDE TFT-LCD TV

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 43
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f9da04d2-c6a9-4a54-b1cc-3759e102fc5a
Producer                        : Acrobat Distiller 4.0 for Macintosh
Modify Date                     : 2004:09:22 17:42:56+09:00
Create Date                     : 2004:09:21 18:21:47Z
Creator Tool                    : QuarkXPress3.3k: AdobePS 8.5.1
Metadata Date                   : 2004:09:22 17:42:56+09:00
Document ID                     : uuid:f7b08698-5c59-441f-9fc7-4eb79f9e4eb6
Format                          : application/pdf
Title                           : #26WT_HY_EN¹ÌÁÖÇ×
Creator                         : µðÀÚÀγÝ
Author                          : µðÀÚÀγÝ

EXIF Metadata provided by EXIF.tools