Digital Device DPD-6000 60'' PLASMA DISPLAY MONITOR User Manual

Digital Device Inc. 60'' PLASMA DISPLAY MONITOR

User Manual

Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Appendix 6. User Manual User’s Manual PPPLLLAAASSSMMMAAA DDDIIISSSPPPLLLAAAYYY It’s the creative world of plasma display MODEL : DPD-6000
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 WARNING RISK OF ELECTRICAL SHOCK, DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute an electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Notices to User This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. One or more of the following statements may be applicable: FCC Warning CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Manual Contents Manual Contents 3 Features and Package Contents - Features 4 - Packages Contents 4 I/O Definitions 5 Front and Rear Controls - Front 6 - Rear Controls 6 Remote Control - Remote Control Basic 7 - Remote Control Details 8 Basic Operation - AV Input/Ouput Terminal 10 - TV 10 - Video 10 - S-VHS 11 - SCART 11 - Monitor Out Connection 12 - Component Video 12 - PC 13 - External Speaker & Headphone Connection 13 TV Channel Memory - Auto Channel Memory 14 - Manual Channel Memory 15 Picture - Picture Adjustment 16 - Picture Size Adjustment 17 - Picture Adjustment in PC Mode 18 - Picture Size Adjustment in PC Mode 19 Audio - Audio Mode Setting 20 - Audio Adjustment 21 Picture in Picture - Picture in Picture Mode Setting 22 - Watching Picture in Picture 23 Video Signal Format - Video Signal Format Setting 24 Color Temperature - Color Temperature Setting 25 Specifications 26 Troubleshooting 27
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Features and Package Features - 42" Diagonal Viewing Area - Menu driven On Screen Display (OSD) for Brightness and Contrast, Sharpness, Hue and Saturation , NTSC/PAL, Channel, PIP(Picture in Picture), Aspect Ratio, Input Source, Audio, Audio Adjust, Language, Color Temperature - Cable TV ready - IR Remote control for all functions - Built-in Television Tuner - Zoom Feature (up to 500%) - Freeze Picture Feature - Rotate Picture Feature - Headphone output (only sub sound) - Speaker output : Left, Right, Center, Surround-L, Surround-R, Sub-Woofer - Selectable Aspect Ratio (16:9, 4:3, User Adjusting Mode) - PIP (Picture in Picture) Function - Multiple Mounting Options : Wallmount or Stand - Monitor Composite Video Output - Large Viewing Angle (160 °) - Seven (7) Possible Video Sources : 1 PC 2 External RCA A/V Inputs 1 S-VHS Input 1 SCART Input 1 Component Video Input 1 TV Package Contents - 42" Plasma TV - User's Manual - Full function Remote Control - A set of three AAA Batteries for Remote Control - AV Cord - AC Power Cord
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 I/O Definitions Front Panel Controls - Main Power ON/OFF - Power ON/OFF - Channel UP - Channel DOWN - Volume UP - Volume DOWN - AV Rear Unit I/O's - AC Power Input - F-Type (NTSC) or Din-Type (PAL) Connector for Antenna Input - Monitor Composite Video Output - Monitor Line Level Audio Output - S-VHS Input - Composite Video Input (2) - Line Level Audio Input (2) - SCART Input/Output - DVD Component Video Input - DVD Line Level Audio Input - PC D-sub Connector Input - PC Headphone Audio Input - Headphone Audio Output - Speaker Output : Left, Right, Center, Surround-L, Surround-R, Sub-woofer
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Front and Rear Controls Front Rear Controls The recessed AV input/output terminals allow the user to have the option of using the mounting stand or wall mounting the 42" Plasma Television. The television itself is only 95mm wide. AV Input/Output Terminal AV CH Down/Up Vol Down/Up Power /Main Power LED / Remote Control
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Remote Control Remote Control Basic Remote Control POWER Pressing this button turns the television ON and OFF. CH/VOL BUTTONS These buttons are used to adjust the channel selected and the volume level. Number Buttons Used to enter channels selected. AV Buttons ( PC / VIDEO1 / VIDEO2 / VIDEO3 / TV ) Use this button for signal Menu Button The center button is used to pull up the menu screen. The surrounding buttons are used to make adjustments to the menu item selected. (ex. Picture, Sound and PIP adjustments)
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Remote Control Details MUTE This button mutes the televisions sound. STILL Pressing this button will stop/freeze the picture. SLEEP This button allows the user to set the sleep timer. RECALL This button will allow the user to view the setting status. STEREO Allows MONO, STEREO or SAP mode selection. ZOOM Pressing the up and down buttons allows the user to zoom in or out the picture.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Remote Control PIP ON/OFF Pressing this button toggles picture in picture on and off. SWAP This button allows the user to swap the picture in picture for picture on the main screen. CH ▲/▼ Pressing this button up or down allows channel selection of the picture in picture. POS This button switches the screen location of the picture in picture viewing screen. There are four possible screen locations for the picture in picture. PIP AV This button switches the mode selection of the picture in picture viewing screen. AUDIO This button switches the Speaker Out of picture in picture Mode.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Basic Operation 1. AV Input/Output Terminal 2. TV 3. VIDEO 1. Connect as the shown drawing. 2. Power on. 3. Press the [TV] button. 1. Connect as the shown drawing. 2. Power on. 3. Press the [VIDEO1] or [VIDEO2] button.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Basic Operation 4. S-VHS 5. SCART Connection 1. Connect as the shown drawing. 2. Power on. 3. Press the [VIDEO1] button. <Caution> Audio input must be connected with [Video1]. In the case when all input sources of S-VHS and Video1 Port are occupied, S-VHS input Sources display preceding to Video1 Port. 1. Connect as the shown drawing. 2. Power on. 3. Press the [VIDEO2] button. <Caution> In the case when all input sources of SCART and Video2 Port are occupied, SCART input Sources display preceding to Video2 Port.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Basic Operation 6. MONITOR OUT Connection 7. COMPONENT Video (ex. DVD, DTV Set-top Box) 1. Connect as the shown drawing. 2. Power on. 3. Press the [VIDEO3] button. <Caution> Monitor out is only applied to [TV], [VIDEO1], [VIDEO2].
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Basic Operation 8. PC 9. External Speaker & Headphone Connection 1. Connect as the shown drawing. 2. Power on. 3. Press the [PC] button. 1. Power Off. 2. Connect as the shown drawing. 3. Power on. 4. Adjusting Audio setting. <Caution> Headphone outputs Sub-Signal Sounds.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 TV Channel Memory Auto Channel Memory Follow these steps for setting the Channel Memory automatically: • Press the [MENU] button. ‚ Select [Channel] by the [ ]/[ ] buttons. ƒ Select [Status] by pressing the [NEXT] button. „ Select TV signal input mode by pressing the [ADJUST] button. … Select [Auto Channel] by pressing the [NEXT] button. † Select [ON] by pressing the [ADJUST] buttons. ‡ Press the [MENU] button to stop the auto channel memory. Auto Memory When Auto memory is on, it will scan CH 2～69 on the Air setting and CH 1～125 on the Cable setting. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 TV Channel Memory Manual Channel Memory Follow these steps to manually set the Channel Memory : • Select the channel by pressing the number button(s). ‚ Press the [MENU] button. ƒ Select [Channel] by the [ ]/[ ] buttons. „ Select [Fine Tuning] mode by using the [NEXT] button. … Press the [ADJUST] button for the tuning adjustment. † Select [Memory] by using the [NEXT] button. ‡ Select [Erase] or [Add] by pressing the [ADJUST] buttons. ˆ Press the [MENU] button to exit the Channel Memory setting. Fine Tuning The [ADJUST] button on the remote control will move the slide adjustment of the fine tuning bar positively or negatively. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Picture Picture Adjustment Follow these steps to adjust the picture : • Press the [MENU] button. ‚ Select the desired Mode by using the [ ]/[ ] buttons. ƒ Move to the desired Mode by pressing the [NEXT] button. „ Press the [ADJUST] button for adjusting the picture … Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Picture Picture Size Adjustment Follow these steps to adjust the picture size : • Press the [MENU] button. ‚ Select the Aspect Ratio by using the [ ]/[ ] buttons. ƒ Move to the desired Mode by pressing the [NEXT] button. „ Press the [ADJUST] button to adjust the picture size ratio. … Press the [MENU] button to exit Picture Size Adjustment. [ZOOM + ] / [ZOOM - ] Button : Using the [ZOOM] button on the remote controller, you can expand the picture size 0 up to 500%. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Picture Picture Adjustment in PC Mode Follow these steps to adjust the picture in PC Mode : • Press the [MENU] button. ‚ Select the desired Mode by using the [ ]/[ ] buttons. ƒ Move to the desired Mode by pressing the [NEXT] button. „ Press the [ADJUST] button for adjusting the picture in PC Mode … Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Picture Picture Size Adjustment in PC Mode Follow these steps for setting the Picture Size Adjustment of PC Mode. • Press the [MENU] button. ‚ Select the Normal Scaling Modes by using the [ ]/[ ] uttons. ƒ Move to the desired mode by pressing the [NEXT] button. „ Press the [ADJUST] button to select the proper mode. … Press the [MENU] button to exit the adjustment menu. [ZOOM + ] / [ZOOM - ] Button : Using the [ZOOM] button on the remote controller, you can expand the picture size 0 up to 500%. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Audio Audio Mode Setting Follow these steps for setting Sound Mode : • Press the [MENU] button. ‚ Select the Audio by using the [ ]/[ ] buttons. ƒ Move to the desired Mode by pressing the [NEXT] button. „ Press the [ADJUST] button to make the adjustment for Sound … Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Audio Audio Adjustment Follow these steps to adjust the Sound : • Press the MENU button. ‚ Select the Audio Adjust by using the [ ]/[ ] buttons. ƒ Move to the desired Mode by pressing the [NEXT] button. „ Press the [ADJUST] button to make the adjustment for Sound … Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green. BASS : Changes the level of low frequency sound. TREBLE : Changes the level of high frequency sound BALANCE : Changes the balance of the left and right channels. Cen/Sur BALANCE : Changes the balance of the center and surround channels.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Picture in Picture Picture in Picture Mode Setting Follow these steps below to set Picture in Picture mode : • Press the [MENU] button. ‚ Select Picture in Picture by using the [ ]/[ ] button. ƒ Select PIP size mode by pressing the [NEXT] button. „ Move to desired mode by pressing the [ADJUST] button. … Select PIP Source Mode by pressing the [NEXT] button. † Select PIP Source by pressing the ADJUST button. ‡ Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Picture in Picture Watching Picture in Picture Press the [PIP ON/OFF] button. Watching PIP Press the [PIP AV] button. Changing the Sub Picture to AV Press the [▲ CH ▼] button. Changing the Sub Picture Channel Press the [POS] button. Changing the Sub Picture Position Press the [SWAP] button. PIP at PC Mode PC signal can be seen on the main picture but not on the sub picture. AT 800×600 mode, you can optimize PIP. Swapping Main for Sub picture
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Video Signal Format Video Signal Format Setting Follow these steps for setting the Video Signal Format. • Press the [MENU] button. ‚ Select the Video Mode by using the [ ]/[ ] buttons. ƒ Move to the desired system by pressing the [NEXT] button. „ Press the [ADJUST] button to select the desired system. … Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green. Auto : The video signals are automatically detected and the format is set accordingly. NTSC M : This is the standard format used mainly in the United States and Korea. PAL : This is the standard format used mainly in the United Kingdom and Germany. PAL-M : This is the standard format used mainly in Brazil. PAL-N : This is the standard format used mainly in Argentina. SECAM : This is the standard format used mainly in France and Russia.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Color Temperature Color Temperature Setting Follow these steps for setting the Color Temperature. • Press the [MENU] button. ‚ Select the Color Temperature by using the [ ]/[ ] buttons. ƒ Move to the desired mode by pressing the [NEXT] button. „ Press the [ADJUST] button to select the desired mode. … Press the [MENU] button to exit the adjustment menu. ※ Highlighted choice will be in green. Color Temperature : The higher temperature the coolest image looks like. The lower temperature the warmest image looks like.
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Specifications Power Source AC100V~240V, 50/60㎐ Power Consumption < 350W (Typical) Display Panel Screen Size 1317.12(H) x 743.04(W) Number of Pixels 1280(H) x 720(V) Brightness 500 cd/m2 Contrast Ratio 500:1 Displayable Colors 16,770,000 Colors Viewing Angle Over 160 degrees Display Mode Input Signal TV, Video, S-VHS, Component, PC RF Input System NTSC(F-Type) or PAL(DIN-Type) Video Input System NTSC, PAL, SECAM Input/Output Input PC (P), PC(S) Video1(V, L, R)/S-VHS Video2 (V, L, R)/SCART Video3 [Component (Y, Pb, Pr), Sound (L, R)] RF IN (NTSC F-TYPE, PAL DIN-TYPE) Output Monitor Out (V, L, R)/ SCART Speaker Out (L,R,Center,Surround L/R,Sub-W), Headphone Weight Without Stand 62 Kg Dimensions Without Stand 1490(W) x 919(H) x 100mm(D) Operation Condition Temperature 0° C ～ 40° C Humidity 20% ～ 80% Storage Temperature -25° C ～ 60° C
Digital Device Inc. 60” PLASMA DISPLAY MONITOR DPD-6000 Report No: BWS-03-EF-0020 FCC ID : PQZDPD-6000 Date of Test : April 17, 2003 Troubleshooting Symptom Cause Possible Solution No Power Power to the TV is not Check source of power to the TV. plugged in. Unit will not respond to Sensor is blocked. Clear path for sensors. remote control Batteries in remote control Clean sensor lens. are weak. Replace batteries. No signal is displayed Video source incorrect. Check video source connection. Make sure TV is set to correct video source. Picture scrolls or is Antenna type or location Change antenna. fuzzy Try antenna in different location.

Navigation menu