Digital Monitoring PC0117 LOW POWER TRANSCEIVER User Manual

Digital Monitoring Products Inc LOW POWER TRANSCEIVER Users Manual

Users Manual

InstallatIon GuIdeXt lIte™ Panel
MODEL XTLINSTALLATION GUIDE FCC NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is •connected.Consult the dealer or an experienced radio/TV technician for help.•Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’s authority to operate the equipment.This device has been designed to operate with the integrated PCB antenna having a maximum gain of 1.8 dB. Antennas having a gain greater than 1.8 dB are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.If necessary, the installer should consult the dealer or an experienced radio/television technician foradditionalsuggestions.Theinstallermayndthefollowingbooklet,preparedbytheFederalCommunications Commission, helpful:“How to identify and Resolve Radio-TV Interference Problems.” ThisbookletisavailablefromtheU.S.GovernmentPrintingOfce,WashingtonD.C.20402StockNo.004-000-00345-4©2010DigitalMonitoringProducts,Inc.InformationfurnishedbyDMPisbelievedtobeaccurateandreliable.This information is subject to change without notice.
XTL Installation Guide Digital Monitoring Productsitable of ContentsPanel Specications1.1 Power Supply .........................................11.2 Communication .......................................11.3 Keypads .................................................11.4 Number of Zones ....................................11.5 EnclosureSpecications ..........................1Introduction2.1 SystemCongurations .............................22.2 Caution Notes .........................................22.3 Compliance Instructions ..........................2System Components3.1 Accessory Devices ...................................3Installation4.1 MountingtheEnclosure ...........................4Primary Power Supply5.1 DC Input ................................................4Secondary Power Supply6.1 Standby Battery ......................................56.2 Replacement ..........................................56.3 Battery Supervision .................................5LED Operation7.1 BacklitLogo ............................................6Reset Button8.1 Description .............................................6Programming Connection9.1 ProgrammingConnection ........................6On-Board 1100 Series Wireless10.1 Wireless Antenna ...................................610.2 LED Operation ........................................6Wireless Keypads11.1 MountingKeypads ..................................711.2 Wireless Keypad Association ....................711.3 ExistingKeypadConrmation ...................7Wireless Zones12.1 Description .............................................7Flash Load Button13.1 Description ............................................8Listed Compliance Specications14.1 Introduction ...........................................914.2 UseMarking ...........................................914.3 NFPA 72 .................................................914.4 Types Of Service .....................................914.5 Bypass Reports .......................................914.6 Battery Standby ......................................9
Digital Monitoring Products XTL Installation Guideiitable of ContentsHousehold Burglar-Alarm System Units ANSI/UL 102315.1 Bell Cutoff ..............................................915.2 Entry Delay ............................................915.3 Exit Delay ...............................................915.4 Wireless External Contact ........................915.5 Wireless Supervision Time .......................915.6 Wireless Audible Annunciation .................915.7 Panel location .........................................915.8 Test Frequency .......................................9Central Station Burglar Alarm Units ANSI/UL 161016.1 Standard Line Security ..........................1016.2 Remote Disarm .....................................1016.3 Central Station ......................................10Household Fire Warning System ANSI/UL 985 NFPA 72 Specications17.1 BellOutputDenition ............................1017.2 HouseholdSystem ................................1017.3 Wireless External Contact ......................1017.4 Wireless Supervision Time .....................1017.5 WirelessFireVerication ........................1017.6 Battery Standby ....................................1017.7 Test Frequency .....................................10False Alarm Reduction Programmable Options ANSI/SIA CP-01-200718.1 ShippingDefaultsandRecommendedProgramming1118.2 Entry Delay ..........................................1218.3 Local Bell .............................................1218.4 Minimum Installation Requirements ........12Revisions to This DocumentListings and Approvals
XTL Installation Guide Digital Monitoring Products1Panel sPeCIfICatIonsPanel Specications1.1 Power SupplyInput:   12VDCStandbyBattery: 3.7VDCLithiumAll circuits inherent power limited1.2 CommunicationBuilt-inCellularcommunicationtoDMPModelSCS-1RReceivers.CellularServiceisrequiredbeforeusingtheXTLforsignaltransmission.TheXTLpanelcomeswithaSIMcardreadyforactivationwithSecureComWireless,LLC.Moreinformationisavailableatwww.securecomwireless.com.1.3 KeypadsYoucanconnectupto4alphanumeric9000Serieswirelesskeypads.1.4 Number of ZonesXTLhas28wirelessinitiatingzonesnumbered1-28•Zonenumbers31to34and41to44cansupport1100SeriesKeyFobsorDMPwirelessoutputmodules•1.5 Enclosure SpecicationsTheXTLpanelshipsinaplasticenclosurewithauser’sguideandprogrammingsheet.Size Color5.58”Wx3.75”Hx1”D White(W)
Digital Monitoring Products XTL Installation Guide2IntroduCtIonIntroduction2.1 System CongurationsThe panel can be programmed to operate as any of the following system types:• All/Perimetersystemthatprovidesoneperimeterareaandoneinteriorarea• Home/Sleep/Awaysystemthatprovidesoneperimeter,oneinterior,andonebedroomarea.Thebedroom area provides for any protection devices the user wants disarmed during their sleeping hours and armed in the Away mode. • Sixareasystemthatprovidesareasofprotectionthatcanbeindependentlyarmedordisarmed. 2.2 Caution NotesThroughoutthisguideyouwillseecautionnotescontaininginformationyouneedtoknowwheninstallingthepanel.Thesecautionsareindicatedwithayieldsign.Wheneveryouseeacautionnote,makesureyoucompletely read and understand its information. Failing to follow the caution note can cause damage to the equipment or improper operation of one or more components in the system. 2.3 Compliance InstructionsForapplicationsthatmustconformtoalocalauthoritiesinstallationstandardoraNationalRecognizedTestingLaboratorycerticatedsystem,pleaseseetheListedComplianceSpecicationssectionneartheendof this guide for additional instructions.
XTL Installation Guide Digital Monitoring Products3system ComPonentsSystem Components3.1 Accessory DevicesDMP Two-Way Wireless Devices1100R Repeater Provides additional range for wireless devices.1101UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two individualreportingzonesfromonewirelesstransmitter.1102UniversalTransmitter Provides one external contact.1103UniversalTransmitter Provides both and internal and external contacts that may be used at the same time to yieldtwoindividualreportingzonesfromonewirelesstransmitter.RequiresEOLresistorforexternal contact.1105UniversalTransmitter Provides both internal and external contacts that may be used at the same time to yield two individualreportingzonesfromonewirelesstransmitter.*1114Four-ZoneExpander ProvidesfourwirelesszoneswithEOLresisters.*1116RelayOutput Provides one Form C relay.*1117LEDAnnunciator Provides a visual system status indicator.*1119DoorSounder Provides a battery operated sounder*1121PIRMotionDetector Provides motion detection with pet immunity.1125PIRMotionDetectorProvidesmultiplelenscongurations,dualcoverageareaselection,andsensitivityadjustments.*1126C/*1126R/*1126WPIRMotionDetectorCeilingmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disablefunctionality.1127C/1127WPIRMotionDetectorWallmountmotiondetectorwithpanelprogrammablesensitivityandDisarm/Disablefunctionality.*1129GlassbreakDetector Detectstheshatteringofframedglassmountedinanoutsidewallandprovidesfull-patterncoverage and false-alarm immunity.*1131RecessedContactProvides concealed protection for doors, windows or other applications.1135Siren Provides a battery operated siren*1139BillTrap Providesasilentalarmoptionforretailandbankingcashdrawers.1142BCTwo-buttonPanicBeltClip Transmitter Provides portable two-button panic operation.1142Two-buttonPanicTransmitterProvides permanently mounted under-the-counter two-button panic operation.*1145(Four-Button) *1146(Two-Button) *1147(One-Button)KeyFobtransmittersdesignedtoclipontoakeyringorlanyard.1161ResidentialSmokeDetector Residentialsmokedetectorwithsounder.1162ResidentialSmokeDetector Residentialsmoke/heatdetectorwithsounderandxedrate-of-riseheatdetector.KeypadsLCDkeypads Allowsyoutocontrolthepanelfromvariousremotelocationsusing9000SeriesWirelessKeypads.* These devices have not been investigated and shall not be used in listed installations
Digital Monitoring Products XTL Installation Guide4InstallatIonInstallation4.1 Mounting the EnclosureTheenclosurefortheXTLpanelmustbemountedusingtheprovided#6screwsinthefourmountingholesshowninFigure2.Mounttheenclosureinasecure,dryplacetoprotectthepanelfromdamageduetotampering or the elements. It is not necessary to remove the PCB when installing the enclosure.65555RESETS1LOADS2BATJ1PROGREDPWRMODEL XTLMounting HoleLocationsTX RF RXFigure 2: Mounting Hole LocationsPrimary Power Supply5.1 DC InputMounttheXTLpanelnearawalloutletfortheModel372-500plug-inDCpowersupply.Inadditiontopoweringthepanel,theDCplug-inpowersupplyalsochargestheback-upbattery.The372-500mustbelocatedwithin100feetofthepanelusing22AWGwireor250feetusing18AWGwire.Usethefollowingsteps to connect the plug-in power supply:1.Using18or22AWGwire,connectthepanelPWR(J2)rstterminal(+)tothepositiveterminalonthe power supply.2.ConnectthepanelPWR(J2)secondterminal(-)tothenegativeterminalonthepowersupply.3.Plugthepowersupplyintoa110VoltACdedicatedoutletnotcontrolledbyaswitch.65555RESETS1LOADS2BATJ1PROGREDPWRMODEL XTLWire Exits for DC Power Supply+-TX RF RXModel 372-500DC Plug-inPowerSupplyUse 18 AWG or 22 AWG for Power Supply connection+_Figure 3: DC Power Supply Connection
XTL Installation Guide Digital Monitoring Products5InstallatIonSecondary Power Supply6.1 Standby BatteryTheXTLrechargeablebatteryisusedtoprovide24hoursofbackupbatterypowerwhenDCpowerisnotavailable.ThebatteryisintendedforbackuppoweronlyandnottooperatetheXTLpanelonadailybasis.Ifthebatteryislow,ornotpluggedintotheJ1batteryconnector,alowbatteryconditionisindicatedbytheXTLpanel.Note:IfremovingtheXTLpanelfromservice,disconnectthebackupbatteryfromtheXTLconnector.6.2 ReplacementUsethefollowingstepstoreplacetheXTLstandbybattery.DMPrecommendsreplacingthebatteryevery3years under normal use.Top PCB SnapsBottom PCB Snaps Battery connector3.7V Rechargeable BatteryFigure 4: Standby Battery Replacement1. Unplugthebatteryconnector(J1)fromtheXTLpanel.2. LoosenthetopPCBsnaps.3. LeanthepanelPCBforwardandliftoutfromthebottomPCBsnaps.4. Removeandproperlydisposeoftheusedbattery. Caution:Riskofre,explosion,andburns.Donotdisassemble,heatabove212°F(100°C), or incinerate. Properly dispose of used batteries. 5. PlacethenewbatteryintotheXTLhousingbasewiththebatterywiresdirectedtowardthebottomrightcorner.SeeFigure4.6. SettheXTLPCBintothebottomsnapsandpressintothetopsnapstosecureinplace.7. Plugthebatteryintothepanelconnector(J1).6.3 Battery SupervisionThepanelteststhebatteryonceeveryhourwhenDCpowerispresent.Thistestoccurs15minutespasteachhourandlastsforveseconds.Aloadisplacedonthebatteryandifthebatteryvoltageislow,alowbatteryisdetected.IfDCpowerhasfailed,alowbatteryisdetectedanytimethebatteryvoltagefallsbelow3.7V.
Digital Monitoring Products XTL Installation Guide6InstallatIonLED Operation7.1 Backlit LogoThebacklitlogoindicatesthePowerandArmedstatusofthepanel.Dependingontheoperation,theLEDdisplaysinRedorGreenaslistedinthetable.Color and Activity OperationGreenSteady PanelDisarmed,ACPowerOK,BatteryOKGreenBlinking PanelDisarmed,ACPowerOK,BatteryFaultNoLight PanelDisarmed,ACPowerFault,BatteryOKRedSteady PanelArmed,ACPowerOK,BatteryOKRed/GreenAlternate PanelArmed,ACPowerOK,BatteryFaultRedBlinking PanelArmed,ACPowerFault,BatteryOKReset Button8.1 DescriptionTheresetbutton(S1)islocatedontherightsideofthecircuitboardandisusedtoresettheXTLmicroprocessor.Toresetthepanelwhenrstinstallingthesystem,presstheresetbuttonafterapplyingpower to the panel. To reset the panel while the system is operational, for example, prior to reprogramming, press the reset buttonfor1-2secondswithoutpoweringdownthesystem.Afterresettingthepanel,beginprogrammingwithin30minutes.Ifyouwaitlongerthan30minutes,youmustresetthepanelagain.Programming Connection9.1 Programming ConnectionAlocking4-pinheader(PROG)isprovidedtoconnectakeypadwhenusingaDMPModel330ProgrammingCable.ThisprovidesaquickandeasyconnectionforprogrammingtheXTLpanel.Afterprogrammingiscomplete,removethekeypad.Note:ThePROGheaderdoesnotprovideaKeypadDataBusconnection.On-Board 1100 Series Wireless10.1 Wireless Antenna TheXTLWirelessAntennaisintegratedintothecircuitboard.TheXTLbuilt-inwirelessreceiveroperateswithDMP1100Seriestransmitters.Seesection3.1foralistofaccessorydevices.10.2 LED OperationGreen (TX):ThegreenLEDasheseverytimethereceivertransmits(32timespersecond).Ifahousecodeisnotprogrammedinthepanel,thepanelisreset,orthepanelispoweredoff,thegreenLEDisoff.Undernormaloperation,thegreenLEDashesconstantlywithnointerruptionorchange.Yellow (RX):TheyellowLEDasheseverytimethereceiverhearsamessagefromaprogrammedwirelesstransmitter.Whenamessageissentbyatransmitter,typicallybypressingorreleasingthetamperswitch,theyellowLEDshouldashindicatingthatthereceiverreceivedamessagefromthetransmitter.IftheLEDneverashes,thetransmitterisnotgettingthroughtothereceiver.Thiscouldbebecauseofamisprogrammedserialnumberorthetransmitteristoofaraway.Undernormaloperation,theyellowLEDashesateverytripofeverywirelesstransmitterandoccasionallywhenthetransmittersperformtheirperiodiccheck-in.ItisnotunusualforthisLEDtostayoffformanyminutesatatimewhennotransmittersare communicating.
XTL Installation Guide Digital Monitoring Products7InstallatIonWireless Keypads11.1 Mounting KeypadsDMPkeypadshaveremovablecoversthatallowthebasetobemountedonawallorotheratsurfaceusingthe screw holes provided on each corner. 11.2 Wireless Keypad AssociationPressingtheresetbutton3timeswithin5secondsenablesthekeypadassociationmode.Foroneminutethepanellistensforwirelesskeypads.Anykeypadsnotalreadyassociatedwithanotherpanelareaccepted.Therstkeypaddetectedisassignedtotherstopenkeypadaddress.Keypadsareautomaticallyassignedaddressesbasedupontheorderinwhichtheyaredetected.Amaximumof4keypadsmaybeassociatedwith a panel.11.3 Existing Keypad ConrmationDuringtheoneminutetimeperiod,thepanelalsoconrmsthatprogrammedkeypadsarestillfunctioning.Wireless Zones12.1 DescriptionXTLpanelsprovide28wirelesszonesnumbered1to28.Thedefaultzonenamesaredescribedbelow.Zone Number Zone Name Zone Type Area Assignment1 FRONT DOOR EX PERIM2 BACK DOOR EX PERIM3 INTERIOR DOOR NT INT4 UPSTAIRS DOOR EX PERIM5 BASEMENT DOOR EX PERIM6 GARAGE DOOR EX PERIM7 WAREHOUSE DOOR EX PERIM8 SHIPPING DOOR EX PERIM 9 BREAKROOM DOOR NT INT 10 STOCKROOM DOOR NT INT 11 FRONT MOTION NT INT 12 BACK MOTION NT INT 13 INTERIOR MOTION NT INT 14 UPSTAIRS MOTION NT INT 15 BASEMENT MOTION NT INT 16 GARAGE MOTION NT INT 17 GLASSBREAK NT INT 18 WATER DETECTOR AUX 1 INT 19 LOW TEMPERATURE AUX 1 INT 20 SMOKE DETECTOR FI 21 FRONT SMOKE FI 22 BACK SMOKE FI 23 INTERIOR SMOKE FI 24 UPSTAIRS SMOKE FI 25 BASEMENT SMOKE FI 26 GARAGE SMOKE FI 27 WAREHOUSE SMOKE FI 28 SHIPPING SMOKE FI
Digital Monitoring Products XTL Installation Guide8InstallatIonFlash Load Button13.1 Description TheXTLpanelsoftwarecanbeupdatedviathepanel’sprogramming(PROG)header.Toupdatethepanelwith a new software version, complete the following steps at the protected premise: 1. ConnectaDMP399CablefromtheProgrammingHeadertotheserialportofyourPCoperatingRemoteLinkandcontainingtheXTLRUle.3. StartRemoteLinkandcreateoropentheXTLcontrolpanelaccountthatmatchesthepaneltobeupdated.4. SettheConnectionInformationTypetoDirectwithabaudrateof38400andchoosetheappropriateCOMport.5. SelectPanel>RemoteUpdate,thenselectthecorrectRUlefortheXTpanelmodel.6. PressandholdtheLOADbutton(S2),thenpressandreleasetheRESETbutton.7. ReleasetheLOADbuttonandclick<Update>inRemoteLink.8. Afterthesoftwareupdateiscompleted,removethe399cableandpresstheRESETbuttontoresume normal panel operation.
XTL Installation Guide Digital Monitoring Products9InstallatIonListed Compliance Specications14.1 IntroductionTheprogrammingandinstallationspecicationscontainedinthissectionmustbecompletedwheninstallingtheXTLinaccordancewithanyoftheANSI/ULburglarystandards.Additionalspecicationsmayberequiredby a particular standard.14.2 Use MarkingCommercialCentralStation;HouseholdFireandBurglarWarningSystemControlUnit(Cellular)14.3 NFPA 72ThisequipmentshouldbeinstalledinaccordancewithChapter11oftheNationalFireAlarmCode,ANSI/NFPA72-2002,(NationalFireProtectionAssociation,BatterymarchPark,Quincy,MA02269).Printedinformation describing proper installation, operation, testing, maintenance, evacuation planning, and repair serviceistobeprovidedwiththisequipment.Warning:Owner’sinstructionnotice,nottoberemovedbyanyone except occupant.14.4 Types Of ServiceSuitableforCentralStationStandardLineSecurity.SuitableforHouseholdFireandHouseholdBurglary.Testweekly.14.5 Bypass ReportsThebypassreportsmustbeprogrammedasYESforalllistedburglaryapplications.14.6 Battery StandbyTheXTLisshippedwithabatteryfor24hourbatterystandbyoperation.Household Burglar-Alarm System Units ANSI/UL 102315.1 Bell CutoffThe bell cutoff time cannot be less than four minutes. 15.2 Entry DelayThemaximumentrydelayusedmustnotbemorethan45seconds.15.3 Exit DelayThe maximum exit delay used must not be more than 60 seconds. 15.4 Wireless External ContactWhenused,theExternalContactof1101or1102mustbeprogrammedNormallyClosed.15.5 Wireless Supervision TimeTheZoneInformationSupervisionTimecannotbesetto0(zero).15.6 Wireless Audible AnnunciationTheWirelessAudibleoptionmustbeselectedasDAYforresidentialapplications.15.7 Panel locationMountpanelinsideprotectedarea.15.8 Test FrequencyTheTestFrequencyoptionmustbeprogrammedtosendareportatleastonceevery30days.
Digital Monitoring Products XTL Installation Guide10ComPlIanCeCentral Station Burglar Alarm Units ANSI/UL 161016.1 Standard Line SecurityStandardLineSecurityisprovidedwhentheCheck-intimeissetto3minutes.WhenprogrammedforStandardLineSecurity,ExitTimeRestartisdisabled.Note:TheSecureComWirelesstextplanselectedforthepanelshouldmatchorexceedtheprogrammedMonthlyLimitoradditionalcellularchargesmayapply.16.2 Remote DisarmREMOTEDISARMmustbeprogrammedasNO.16.3 Central StationMESSAGETOTRANSMITprogrammingforzonesmustnotbesettoLOCAL(L).Household Fire Warning System ANSI/UL 985 NFPA 72 Specications17.1 Bell Output DenitionThebelloutputoftheXTLpanelmustbeprogrammedtooperatesteadyonburglaryalarmsandtemporalonrealarms.SeetheXTLProgrammingGuide.17.2 Household SystemAn alarm sounding device must be installed indoors so that it is clearly heard in all sleeping areas.17.3 Wireless External ContactWhenused,theExternalContactof1101or1102mustbeprogrammedNormallyClosed.SeetheXTLProgrammingGuide.17.4 Wireless Supervision TimeTheZoneInformationSupervisionTimemustbe3minutesforredevices.SeetheXTLProgrammingGuide.17.5 Wireless Fire VericationWhenused,theModel1161and1162wirelesssmokedetectorsmustnotbeprogrammedasFireVerication(FV)zonetype.SeetheXTLProgrammingGuide.17.6 Battery StandbyForULlistedapplications,thepanelmusthave24hourbatterystandbyoperation.17.7 Test FrequencyTheTestFrequencyoptionmustbeprogrammedtosendareportatleastonceevery30days.
XTL Installation Guide Digital Monitoring Products11ComPlIanCeFalse Alarm Reduction Programmable Options ANSI/SIA CP-01-200718.1 Shipping Defaults and Recommended ProgrammingSIA CP-01 FEATURE PARAGRAPH # AND DESCRIPTIONDMP PROGRAMMING GUIDE LT-1108 SECTION #REQUIREMENT RANGE SHIPPING DEFAULTRECOMMENDED PROGRAMMING*4.2.2.1ExitTime 8.6ExitDelay Required (Programmable) 45sec.-250sec. 60 Seconds 60Seconds4.2.2.2ProgressAnnunciation 13.14PrewarnAddress AllowedIndividualkeypadsmay be disabled per zoneAll keypadsenabledAllkeypadsenabled4.2.2.3ExitTimeRestart 8.6ExitDelay RequiredOption For re-entry during exit time Enabled Enabled4.2.2.5AutoStayArmonUnvacatedPremises8.17OccupiedPremise - SeeInstallGuide RequiredOption(exceptforremotearming)OccupiedPremiseNO/YESoption EnabledEnabledYesfor Residential Applications4.2.4.4ExitTimeandProgress Annunciation/Disable-forRemoteArmNotAvailableonRemote Arming AllowedOptionProgress Annunciation Always disabled for Remote ArmingNotAvailableRemote Arming not allowed for CP-01 installations.4.2.3.1EntryDelay(s) 8.5EntryDelay Required (Programmable) 30sec.–240Sec.** 30Seconds Atleast30Seconds**4.2.5.1AbortWindow–forNon-FireZones 3.3TransmitDelay RequiredOption DisablebyzoneorzonetypeEnabledNTDYEXZoneEnabled4.2.5.1AbortWindowTime–forNon-FireZones3.3TransmitDelay Required (Programmable)20sec.,30sec.,or40sec.** 30Seconds Atleast20Seconds**4.2.5.1.2AbortAnnunciation 3.3TransmitDelay RequiredOptionAnnunciate that no alarm was transmitted Yes Yes4.2.5.4.1CancelAnnunciationAlwaysEnabled-NotProgrammable RequiredOptionAnnunciate that a Cancel was transmitted(S49)Always Enabled Yes4.2.6.1&4.2.6.2DuressFeatureUserCode+1=AmbushCodeNotAvailableAllowedOptionNo1+derivativeofanother user code/no duplicates with other user codesCode+1Always DisabledNotProgrammable4.3.2SwingerShutdown NotAvailable—AlwaysOn Required Forallnon-rezones,shutdownafter 1 tripAlways On AlwaysOn4.3.2SwingerShutdownDisable 13.13SwingerBypass Allowed For non-police responsezones Yes Enabled(allzones)4.3.3FireAlarmVerication 13.5ZoneType RequiredOption FV Type Zone NoYes as required (unlesssensorscanselfverify)* Programming at installation may be subordinate to other listed requirements for the intended application. **ForlistedInstallations,combinedEntryDelayandTransmitDelayshouldnotexceed1minute.
Digital Monitoring Products XTL Installation Guide12ComPlIanCeFalse Alarm Reduction Programmable Options ANSI/SIA CP-01-2007 (continued)18.2 Entry DelayOnlyuseEntryDelay1.DonotuseEntryDelay2.SeetheXTLProgrammingGuide.18.3 Local BellAllnon-rezonessuchasNight,Day,Exit,Aux1andAux2mustbeprogrammedforlocalbellenabledwitha bell cutoff time set to a minimum of 6 minutes to provide a cancel window of 5 minutes or greater. This doesnotapplytomanuallyoperatedzonetypessuchasPanicandEmergency.TherequirementsaresupercededbyanyrequirementsforCommercialBurglar,HouseholdFireWarning,orHousehold Burglar applications.18.4 Minimum Installation RequirementsSIACP-01-2007minimumsysteminstallationrequirementsincludeanXTL,an1135WirelessSiren,andcommunicationtoanSCS-1Rreceiverplusa9000SeriesWirelesskeypad.
XTL Installation Guide Digital Monitoring Products13revIsIonsRevisions to This DocumentThis section explains the changes that were made to this document during this revision. This section lists theversion,sectionnumberwithheading,andaquicksummaryofthechange.Ver. Section Number and Heading Summary of Changes
LT-11051.01©2010DigitalMonitoringProducts,Inc.800-641-4282www.dmp.comMadeintheUSAINTRUSION•FIRE•ACCESS•NETWORKS2500NorthPartnershipBoulevardSpringfield,Missouri65803-887710045Listings and ApprovalsFCCPart15ID:CCKPC0117IndustryCanadaID:5251A-PC0117UnderwritersLaboratories(UL)Listed ANSI/UL1023 HouseholdBurglar ANSI/UL985 HouseholdFireWarning ANSI/UL1610 CentralStationBurglar

Navigation menu