Digital Monitoring PC0199 All-In-One Panel User Manual Manual

Digital Monitoring Products Inc All-In-One Panel Manual

Manual

INSTALLATION GUIDE XTLtouchTM
TABLE OF CONTENTSAbout the XTLtouch .............. 1Install the XTLtouch ..............2Wall Mount (XTLtouch) ......................... 2Desk Stand (XTLtouchUSB) ................ 2In-Wall........................................................... 2Wall Mount Installation .........3Mount the Backplate ..............................3Install the 265LTE-V-GW ....................... 5Wire for Power .......................................... 7Desk Stand Installation .........9Install the Desk Stand Legs ..................9Power the XTLtouch .............................. 10In Wall Installation ............... 11Prepare for Backbox Installation........11Install the Backbox ................................. 12Install the XTLtouch in the Backbox 14Additional Information ........15Secondary Power Supply...................... 15Replace the Battery .............................. 15Accessories ............................ 17Keypad Cover ........................................... 17Transformer .............................................. 17Cellular Communicator ........................ 17Certifications ......................... 18FCC Information ...................19Industry Canada....................21
Information furnished is believed to be accurate and reliable. This information is subject to change without notice.
Digital Monitoring Products | XTLtouch Installation Guide 1ABOUT THE XTLtouchThe XTLtouch oers flexible features and functionality. It’s composed of an XTLplus panel with an integrated 7872 Graphic Touchscreen Keypad, providing a simple device to control and operate a system. The XTLtouch can be wall-mounted, in wall mounted, or it can provide a simple deskstand option for tabletop use. The XTLtouch provides the following features and functionality: • 5” graphic touchscreen keypad screen• Three-part housing (cover, base, wall)• On-board proximity reader designed to read DMP/HID credentials• On-board Wi-Fi• Z-Wave Plus support• 2400mAh battery back-up• 900MHz Wireless
XTLtouch Installation Guide | Digital Monitoring Products 2INSTALL THE XTLtouchWall Mount (XTLtouch)For wall mount installations, you will use the included backplate to mount the XTLtouch to a wall. Desk Stand (XTLtouchUSB)For desk stand installations, you will use the included legs for tabletop use.In-WallFor in-wall installations, you will use an in wall backbox to mount the XTLtouch into the wall, creating a flush wall mount look. Pro Tip: Mount the XTLtouch near a wall outlet for the plug-in power supply. The power supply should be located within 100 feet of the XTLtouch using 22 AWG wire.
Digital Monitoring Products | XTLtouch Installation Guide 3WALL MOUNT INSTALLATIONMount the Backplate1. Press the tab and remove the backplate from the XTLtouch. See Figure 1.1Figure 1: Removing the BackplateBackplateTab
XTLtouch Installation Guide | Digital Monitoring Products 42. Use the include mounting template, level, and #6 screws to mount the backplate to the wall. See Figure 2 for mounting hole locations. Figure 2: Mounting Hole LocationsLevel
Digital Monitoring Products | XTLtouch Installation Guide 52. Use the include mounting template, level, and #6 screws to mount the backplate to the wall. See Figure 2 for mounting hole locations. Install the 265LTE-V-GW Cellular Communicator (Optional)1. Remove the set screw from the bottom of the XTLtouch.2. Remove the four screws from the back of the XTLtouch. 3. Separate the base from the panel and keypad. See Figure 3.2Figure 3: Installing the 265LTE-V-GW
XTLtouch Installation Guide | Digital Monitoring Products 64. Remove the backing from the flexible antenna and place it inside the housing. 5. Snap the end of the antenna on to the 265LTE-V-GW antenna patch. 6. Insert the 265LTE-V-GW into the eight-pin CELL MODULE header, keeping it parallel to the XTLtouch. 7. Snap the 265LTE-V-GW on to the stando and secure it in place. 8. Replace the base and secure it with the four screws and the one set screw. See Figure 4.Figure 4: Connecting the Antenna
Digital Monitoring Products | XTLtouch Installation Guide 7Wire for PowerSee Figure 5 for wire routing instructions before wiring the XTLtouch for power. 1. Connect the XTLtouch +DC terminal to the positive terminal on the power supply. 2. Connect the XTLtouch -DC terminal to the negative terminal on the power supply. 3. Plug the power supply into a 120 V AC 60Hz dedicated outlet that’s not controlled by a switch. 4. Place the XTLtouch back on to the mounted backplate. 3
XTLtouch Installation Guide | Digital Monitoring Products 8Figure 5: Routing Wires
Digital Monitoring Products | XTLtouch Installation Guide 9DESK STAND INSTALLATIONSee Steps 1 and 2 in Wall Mount installation to install the optional 265LTE-V-GW. Install the Desk Stand Legs1. Insert one leg into the holes in the back of the XTLtouch. 2. Slide the leg upwards until the leg firmly snaps into place. Repeat steps 1 and 2 to install the other leg. See Figure 6.1Figure 6: Connecting the Desk stand Legs
XTLtouch Installation Guide | Digital Monitoring Products 10Power the XTLtouch1. Plug the micro USB end of the cable into the back of the keypad. 2. If desired, insert the cable into the strain relief to secure the XTLtouch from being unattached from its power source. 3. Plug the power supply into an outlet. See Figure 7. 2Figure 7: Strain Relief OptionStrain Relief
Digital Monitoring Products | XTLtouch Installation Guide 11IN WALL INSTALLATIONPrepare for Backbox Installation1. Place the included backbox template on the wall in the desired location.2. Cut along the inside of the template border line, ensuring to not square the corners.3. Place the two included #6 screws approximately 1/4” into the two locking tab holes on the rear wall of the backbox. 1Figure 8: Screw Locations
XTLtouch Installation Guide | Digital Monitoring Products 122Install the Backbox1. Route the 22 AWG wires through the bottom slot in the backbox. 2. Place the backbox in the wall space you created with the locking tabs in a vertical position. See Figure 9.Vertical Locking TabFigure 9: Placing the Backbox in the Wall
Digital Monitoring Products | XTLtouch Installation Guide 133. Once in place, use a Number 2 Phillips screwdriver to tighten the #6 screws that are already in place. This allows the locking tabs to swing into a horizontal position on both sides of the backbox. Pro Tip: In some installations, it may be necessary to secure the backbox to a wall stud. To do this, place the backbox in the wall space you created and secure it to the wall stud by using the side mounting holes. See Figure 10. Figure 10: Securing the Backbox
XTLtouch Installation Guide | Digital Monitoring Products 143Install the XTLtouch in the Backbox1. See Wall Mount Installation to wire the XTLtouch. 2. Insert the top of the XTLtouch into the backbox at a slight angle until the XTLtouch slots connect to the backbox tabs. 3. Push the bottom of the keypad into the backbox until the lower slots snap in to place. See Figure 11. See LT-1321 for additional backbox mounting instructions. Figure 11: Placing the XTLtouch
Digital Monitoring Products | XTLtouch Installation Guide 15ADDITIONAL INFORMATIONSECONDARY POWER SUPPLYThe XTLtouch’s 2400mAh rechargeable standby battery is used to provide four hours of battery power when DC power is not available. The battery is intended for back power only and should not operate the panel on a daily basis. If the battery is low or not plugged in to the battery connector, a low battery condition is indicated by the panel. If a 24 hour standby battery is needed, connect a 4800mAh battery. Replace the Battery 1. Remove the backplate from the XTLtouch.2. Unplug the battery from the BAT connector and remove it from the PCB.3. Place the new battery in the same location and secure it with the included adhesive. 4. Re-plug the BAT connector.5. Replace the backplate. See Figure 12. Figure 11: Placing the XTLtouch
XTLtouch Installation Guide | Digital Monitoring Products 163.8V 4800mAh Rechargeable Battery(required for 24 hour standby)3.8V 2400mAh Rechargeable BatteryFigure 12: Replacing the Battery
Digital Monitoring Products | XTLtouch Installation Guide 17ACCESSORIESKeypad Cover777 Protective Keypad CoverTransformer 372-500-W 12 VDC Nominal Power Supply (STC-12500W)371-500U-W Replacment Transformer, Cable, and StrapCellular Communicator 265LTE-V-GW Cellular Communicator (Compatible with XTLplus Series panels with Version 171 or higher)
XTLtouch Installation Guide | Digital Monitoring Products 18FCC Wireless Receiver and Z-Wave ApprovalsFCC ID: CCKPC0199IC: 5251A-PC0199FCC Wi-Fi Network ApprovalsFCC ID: VW4-ATWINC1500IC: 20266-WINC1500PBIntertek (ETL) ListedANSI/UL 985 Household FireANSI/UL 1023 Household BurglarANSI/UL 1610 Central Station BurglarANSI/UL 1635 Digital BurglarCERTIFICATIONS
Digital Monitoring Products | XTLtouch Installation Guide 19CERTIFICATIONSThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:FCC INFORMATION
XTLtouch Installation Guide | Digital Monitoring Products 20• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
Digital Monitoring Products | XTLtouch Installation Guide 21This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:1. l’appareil ne doit pas produire de brouillage, et 2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.INDUSTRY CANADA INFORMATION
LT-1788 1.01 18203 © 2018 Digital Monitoring Products, Inc.

Navigation menu