Digital Monitoring PC0199 All-In-One Panel User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3936385
Application ID	cIAAoNONrInfsz2oML6A5w==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	76.4kB (954969 bits)
Date Submitted	2018-07-24 00:00:00
Date Available	2018-07-24 00:00:00
Creation Date	2018-05-31 15:44:50
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-06-01 13:35:48
Document Title	Manual
Document Creator	Adobe InDesign CC 13.1 (Windows)

XTLtouchTM
INSTALLATION GUIDE
TABLE OF CONTENTS
About the XTLtouch............... 1
Install the Backbox.................................. 12
Install the XTLtouch...............2
Install the XTLtouch in the Backbox.14
Wall Mount (XTLtouch).......................... 2
Desk Stand (XTLtouchUSB)................. 2
Additional Information.........15
Secondary Power Supply...................... 15
In-Wall........................................................... 2
Replace the Battery ............................... 15
Wall Mount Installation..........3
Accessories.............................17
Mount the Backplate............................... 3
Keypad Cover............................................ 17
Install the 265LTE-V-GW........................ 5
Transformer ............................................... 17
Wire for Power........................................... 7
Cellular Communicator ......................... 17
Desk Stand Installation..........9
Certifications..........................18
Power the XTLtouch............................... 10
FCC Information....................19
Install the Desk Stand Legs................... 9
In Wall Installation................ 11
Prepare for Backbox Installation........11
Industry Canada....................21
Information furnished is believed to be accurate and reliable.
This information is subject to change without notice.
ABOUT THE XTLtouch
The XTLtouch offers flexible features and functionality. It’s composed of an
XTLplus panel with an integrated 7872 Graphic Touchscreen Keypad, providing
a simple device to control and operate a system. The XTLtouch can be wallmounted, in wall mounted, or it can provide a simple deskstand option for
tabletop use.
The XTLtouch provides the following features and functionality:
•
•
•
•
•
•
•
5” graphic touchscreen keypad screen
Three-part housing (cover, base, wall)
On-board proximity reader designed to read DMP/HID credentials
On-board Wi-Fi
Z-Wave Plus support
2400mAh battery back-up
900MHz Wireless
Digital Monitoring Products
XTLtouch Installation Guide
INSTALL THE XTLtouch
Wall Mount (XTLtouch)
For wall mount installations, you will use the included backplate to mount the
XTLtouch to a wall.
Desk Stand (XTLtouchUSB)
For desk stand installations, you will use the included legs for tabletop use.
In-Wall
For in-wall installations, you will use an in wall backbox to mount the XTLtouch
into the wall, creating a flush wall mount look.
Pro Tip: Mount the XTLtouch near a wall outlet for the plug-in power supply.
The power supply should be located within 100 feet of the XTLtouch using
22 AWG wire.
XTLtouch Installation Guide
Digital Monitoring Products
WALL MOUNT INSTALLATION
Mount the Backplate
1.
Press the tab and remove the backplate from the XTLtouch.
See Figure 1.
Backplate
Tab
Figure 1: Removing the Backplate
Digital Monitoring Products
XTLtouch Installation Guide
2.
Use the include mounting template, level, and #6 screws to mount the
backplate to the wall. See Figure 2 for mounting hole locations.
Level
Figure 2: Mounting Hole Locations
XTLtouch Installation Guide
Digital Monitoring Products
2
Install the 265LTE-V-GW Cellular Communicator (Optional)
1.
Remove the set screw from the bottom of the XTLtouch.
2.
Remove the four screws from the back of the XTLtouch.
3.
Separate the base from the panel and keypad. See Figure 3.
Figure 3: Installing the 265LTE-V-GW
Digital Monitoring Products
XTLtouch Installation Guide
4.
Remove the backing from the flexible
antenna and place it inside the housing.
5.
Snap the end of the antenna on to the
265LTE-V-GW antenna patch.
6.
Insert the 265LTE-V-GW into the eightpin CELL MODULE header, keeping it
parallel to the XTLtouch.
7.
Snap the 265LTE-V-GW on to the
standoff and secure it in place.
8.
Replace the base and secure it with the
four screws and the one set screw.
See Figure 4.
Figure 4: Connecting the Antenna
XTLtouch Installation Guide
Digital Monitoring Products
3
Wire for Power
See Figure 5 for wire routing instructions before wiring the XTLtouch for
power.
1.
Connect the XTLtouch +DC terminal to the positive terminal on the
power supply.
2.
Connect the XTLtouch -DC terminal to the negative terminal on the
power supply.
3.
Plug the power supply into a 120 V AC 60Hz dedicated outlet that’s
not controlled by a switch.
4.
Place the XTLtouch back on to the mounted backplate.
Digital Monitoring Products
XTLtouch Installation Guide
Figure 5: Routing Wires
XTLtouch Installation Guide
Digital Monitoring Products
DESK STAND INSTALLATION
See Steps 1 and 2 in Wall Mount installation to install the optional
265LTE-V-GW.
Install the Desk Stand Legs
1.
Insert one leg into the holes in the back of the XTLtouch.
2.
Slide the leg upwards until the leg firmly snaps into place. Repeat
steps 1 and 2 to install the other leg. See Figure 6.
Figure 6: Connecting the Desk stand Legs
Digital Monitoring Products
XTLtouch Installation Guide
2
Power the XTLtouch
1.
Plug the micro USB end of the cable into the back of the keypad.
2.
If desired, insert the cable into the strain relief to secure the XTLtouch
from being unattached from its power source.
3.
Plug the power supply into an outlet. See Figure 7.
Strain Relief
Figure 7: Strain Relief Option
10
XTLtouch Installation Guide
Digital Monitoring Products
1
IN WALL INSTALLATION
Prepare for Backbox Installation
1.
Place the included backbox
template on the wall in the desired
location.
2.
Cut along the inside of the
template border line, ensuring to
not square the corners.
3.
Place the two included #6 screws
approximately 1/4” into the two
locking tab holes on the rear wall
of the backbox.
Figure 8: Screw Locations
Digital Monitoring Products
XTLtouch Installation Guide
11
2
Install the Backbox
1.
Route the 22 AWG wires through the bottom slot in the backbox.
2.
Place the backbox in the wall space you created with the locking tabs
in a vertical position. See Figure 9.
Vertical Locking
Tab
Figure 9: Placing the Backbox in the Wall
12
XTLtouch Installation Guide
Digital Monitoring Products
3.
Once in place, use a Number 2 Phillips screwdriver to tighten the #6
screws that are already in place. This allows the locking tabs to swing into
a horizontal position on both sides of the backbox.
Pro Tip: In some installations, it may be necessary to secure the
backbox to a wall stud. To do this, place the backbox in the wall
space you created and secure it to the wall stud by using the side
mounting holes. See Figure 10.
Figure 10: Securing the Backbox
Digital Monitoring Products
XTLtouch Installation Guide
13
3
Install the XTLtouch in the Backbox
1.
See Wall Mount Installation to wire
the XTLtouch.
2.
Insert the top of the XTLtouch into
the backbox at a slight angle until
the XTLtouch slots connect to the
backbox tabs.
3.
Push the bottom of the keypad into
the backbox until the lower slots
snap in to place. See Figure 11.
See LT-1321 for additional backbox
mounting instructions.
Figure 11: Placing the XTLtouch
14
XTLtouch Installation Guide
Digital Monitoring Products
ADDITIONAL INFORMATION
SECONDARY POWER SUPPLY
The XTLtouch’s 2400mAh rechargeable standby battery is used to provide four
hours of battery power when DC power is not available. The battery is intended
for back power only and should not operate the panel on a daily basis.
If the battery is low or not plugged in to the battery connector, a low battery
condition is indicated by the panel. If a 24 hour standby battery is needed,
connect a 4800mAh battery.
Replace the Battery
1.
Remove the backplate from the XTLtouch.
2.
Unplug the battery from the BAT connector and remove it from the PCB.
3.
Place the new battery in the same location and secure it with the included
adhesive.
4.
Re-plug the BAT connector.
5.
Replace the backplate. See Figure 12.
Digital Monitoring Products
XTLtouch Installation Guide
15
3.8V 4800mAh Rechargeable Battery
(required for 24 hour standby)
3.8V 2400mAh
Rechargeable
Battery
Figure 12: Replacing the Battery
16
XTLtouch Installation Guide
Digital Monitoring Products
ACCESSORIES
Keypad Cover
777 Protective Keypad Cover
Transformer
372-500-W 12 VDC Nominal Power Supply (STC-12500W)
371-500U-W Replacment Transformer, Cable, and Strap
Cellular Communicator
265LTE-V-GW Cellular Communicator (Compatible with XTLplus Series panels
with Version 171 or higher)
Digital Monitoring Products
XTLtouch Installation Guide
17
CERTIFICATIONS
FCC Wireless Receiver and Z-Wave Approvals
FCC ID: CCKPC0199
IC: 5251A-PC0199
FCC Wi-Fi Network Approvals
FCC ID: VW4-ATWINC1500
IC: 20266-WINC1500PB
Intertek (ETL) Listed
18
ANSI/UL 985		
Household Fire
ANSI/UL 1023		
Household Burglar
ANSI/UL 1610		
Central Station Burglar
ANSI/UL 1635		
Digital Burglar
XTLtouch Installation Guide
Digital Monitoring Products
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1.
2.
This device may not cause harmful interference, and
This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications made by the user and not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Digital Monitoring Products
XTLtouch Installation Guide
19
•
•
•
•
20
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
XTLtouch Installation Guide
Digital Monitoring Products
INDUSTRY CANADA INFORMATION
This device complies with Industry Canada Licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1.
2.
This device may not cause interference, and
This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1.
2.
l’appareil ne doit pas produire de brouillage, et
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Digital Monitoring Products
XTLtouch Installation Guide
21
LT-1788
1.01
18203
© 2018 Digital Monitoring Products, Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2018:05:31 15:44:50-05:00
Creator                         : Adobe InDesign CC 13.1 (Windows)
Modify Date                     : 2018:06:01 13:35:48-05:00
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2018:06:01 13:35:48-05:00
Creator Tool                    : Adobe InDesign CC 13.1 (Windows)
Instance ID                     : uuid:116b3ec0-a345-4bb2-8730-882820b7c8ed
Original Document ID            : xmp.did:bfe6b3b9-76fa-5d49-830f-96dfa66edb1a
Document ID                     : xmp.id:35d5c060-f5e9-ae45-bb76-c84c1b74bb17
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:cc41046a-f9b1-a74d-9e97-09b62553ea01
Derived From Document ID        : xmp.did:b739587d-242f-c94e-993c-ee8a2411c595
Derived From Original Document ID: xmp.did:bfe6b3b9-76fa-5d49-830f-96dfa66edb1a
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.1 (Windows)
History Changed                 : /
History When                    : 2018:05:31 15:44:50-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 28

EXIF Metadata provided by EXIF.tools