KURZ_RENKFORCE_RF100_XL_3D_DRUCKER_de_en Ver. 01 001592620 An Ml KURZ RENKFORCE RF100 XL 3D DRUCKER De En
User Manual: KURZ_RENKFORCE_RF100_XL_3D_DRUCKER_de_en - Ver. 01 Renkforce RF100 XL 3D printer incl. filament from Conrad.com
Open the PDF directly: View PDF .
Page Count: 4
Download | |
Open PDF In Browser | View PDF |
Einrichtung des Zubehörs 1 2 Kurzanleitung RF100 XL 3D Drucker Fertiggerät Best.-Nr. 1592461 RF100 XL Plus Best.-Nr. 1592620 RF100 XL • Druckbett auflegen. Lieferumfang • 3D Drucker Fertiggerät • Seitenschneider • 250 g Original Renkforce PLA-Filament (1,75 mm weiß) • 2,0 mm Innensechskantschlüssel • 8 GB SD-Karte mit „Cura“ Software, 100+ druckfertige 3D Modelldateien • 2x Schraube • Netzteil • Netzkabel • Kurzanleitung (auf Deutsch, Englisch) • Filament-Spulenhalterung • Filamentschlauch • USB-Kabel • Spachtel • Pinzette • Schutzdeckel des Stromanschluss für die Heizplatte öffnen ( 1 ). • Stecker des Heizplattenstromkabels mit dem Stromanschluss verbinden ( 2 ). • 2,5 mm Innensechskantschlüssel • Glas-Druckbett mit vorinstallierter Druckbettfolie (bei Best.-Nr. 1592620) - inkl. Heizplatte und beiliegenden Blue Tape (bei Best.-Nr. 1592461) Nur bei Best.-Nr. 1592461 • Verbindung sichern: Überwurfmutter des Steckers auf den Heizplattenanschluss drehen. 3 4 • 5 x Original Renkforce Filamentmuster (Kupfer-, Holz-, Glow-in-the-Dark-, Colorchange- und Elastikmaterial - jeweils 1,75 mm - 50 g) • 50 g ABS-Filament (1,75 mm schwarz) (bei Best.-Nr. 1592461) Ausführliche Bedienungsanleitungen Eine ausführliche Bedienungsanleitung können Sie auf www.conrad.com/downloads herunterladen oder Sie können den angezeigten QR-Code scannen. Befolgen Sie die Anweisungen auf der Website. Produktbild Nur bei Best.-Nr. 1592461 • Heizplattenkabel in die Kabelhalterung (auf der Druckbettunterseite) stecken. • Mit zwei Schrauben und dem 2,5 mm Innensechskantschlüssel die FilamentSpulenhalterung hinten am 3D Drucker montieren. „Nase“ am Ende der Halterung zeigt nach oben. 5 • SD-Karte mit der Aufkleberseite nach unten einstecken. 7 • Erst Netzkabel mit dem Netzteil verbinden, dann Stromkabel des Netzteils mit dem 3D Drucker verbinden. 6 • Kabelbinder auf beiden Seiten mit dem Seitenschneider durchtrennen. 8 • Im Touchdisplay erscheint < ReadyPrint >. 3D Drucker ist nun einsatzbereit. • Netzstecker des Stromkabels mit der Netzsteckdose verbinden. Produktmerkmale • Max. Größe des Druckobjekts 200 x 200 x 200 mm • Druck diverser Materialien wie PLA, Holz, Elastikmaterial, Kupfer; - zusätzlich ABS (bei Best.-Nr. 1592461) • Druckschichtdicke 0,1 mm - 0,2 mm • 3D Drucker einschalten. • Düsengröße 0,4 mm • Unterstützt das Drucken von SD-Karte, PC und USB Druckbettkalibrierung 1 2 • mitgelieferte „Cura“ Software • Einzel-Extruder • Druckgeschwindigkeit 30 mm/s - 300 mm/s • Farb-Touchdisplay • 3 Nivellierschrauben unter dem Druckbett bis zum Anschlag festziehen. • A4-Papier als Messhilfe zwischen Düse und Druckbett legen. 3 4 • Im Menü < ReadyPrint > zuerst < Set > (Einstellen), dann < Leveling > (Nivellieren) wählen. • SCHRITT 3 für den zweiten, dritten und vierten Punkt wiederholen (Kalibriersequenz und Bewegungsrichtung der Düse werden • < First > (Erster Punkt) betätigen. Düse dargestellt). bewegt sich zum ersten Punkt. • Durch Drehen der ersten Nivellierschraube den Abstand zwischen Düse und Druckbett regeln. 5 • Filament mit leichtem Druck vorwärts schieben bis das Filament langsam in den Extruder eingezogen wird. • Filament loslassen. 6 • Wenn das Filament aus der Düse austritt, < Stop > betätigen. • Entfernen Sie die Filamentreste mit einer Pinzette. Druckvorgang starten 1 • Das Papier sollte leicht geklemmt werden, das beim Bewegen des Papiers ein leichter Widerstand spürbar ist. 2 Filamenteinrichtung 1 2 • Im Menü < ReadyPrint > zuerst < Print > (Drucken) , dann ggf. mehrfach < PageDown > (Nächste Seite) bis der Ordner < 3D Models > zu sehen ist. • Im Ordner < 3D Models > ein druckfertiges Modell auswählen, z. B. < RF100.gcode >. • Ordner < 3D Models > öffnen. • Filament an der Spulenhalterung anbringen. • Filament-Schlauch in die Schlauchhalterung einsetzen. 3 4 3 • Druck bestätigen mit < OK >. • FERTIG. • Das Filament soweit in den Schlauch einführen, bis ca. 5 cm am ExtruderEnde zu sehen sind. Filamenteinzug 1 2 • Im Menü < ReadyPrint > < Move > • Im Menü < ReadyPrint > zuerst (Bewegen) auswählen und dann zwei < Filament >, dann < Preheat > Mal < Z+ > betätigen, um den Abstand (Vorheizen) auswählen. zwischen Düse und Druckbett zu • < Add > mehrfach betätigen, bis die vergrößern. Solltemperatur von 220 °C erreicht ist. 3 4 • Im Menü < Filament >, warten bis die • Im LC-Display erscheint die aktuelle Temperatur (hier 221 °C) die Statusanzeige < filament changing >. Solltemperatur erreicht hat. 3D Drucker ist nun bereit zum Filamenteinzug. • < Load > (Einziehen) betätigen. Dies ist eine Publikation der Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). Alle Rechte vorbehalten, einschl. Übersetzung. Die Vervielfältigung durch irgendeine Methode, d.h. Fotokopie, Mikrofilm oder in einer digitalen, elektronischen, optischen oder in anderer Form erfordert die vorherige schriftliche Genehmigung vonseiten des Herausgebers. Die Vervielfältigung durch Drucken, auch teilweise, ist ebenso untersagt. Die Publikation entspricht dem technischen Stand bei Drucklegung. Copyright 2017 by Conrad Electronic SE. *1592461_1592620_V1_1017_02_LS_qsg_DE Setting up the equipment 1 2 Quick guide RF100 XL 3D printer fully-assembled Item no. 1592461 RF100 XL Plus Item no. 1592620 RF100 XL • Install the print bed. Delivery content • 3D printer fully-assembled • Side cutters • 250 g original Renkforce PLA filament (1.75 mm white) • 2.0 mm hex key • 8 GB SD card with “Cura" software, 100+ ready-to-print 3D model files • 2x screw • Power adapter • Mains cable • Quick installation guide (in German and English) • Filament spool holder • Filament tube • USB cable • Scraper • Tweezers • Lift up the protective cover on the heating plate power connection ( 1 ). • Plug the heating plate power cable into the power connection ( 2 ). • 2.5 mm hex key • Glass print bed with pre-installed print bed film (with item no. 1592620) - includes heating plate and accompanying blue tape (with item no. 1592461) Only with item no. 1592461 • Secure the connection: turn the lock nut in the heating plate connecting plug. 3 4 • 5 x original Renkforce filament samples (copper, wood, glow-in-the-dark, colourchange and elastic - each one 1.75 mm - 50 g) • 50 g ABS filament (1.75 mm black) (with item no. 1592461) Only with item no. 1592461 Detailed Operating Manuals A detailed operating manual can be downloaded from www.conrad.com/downloads or you can scan the QR code on this page. Follow the instructions on the website. Product picture • Insert the heating plate cable into the cable holder (on the lower side of the print bed). 5 • Insert the SD card with the label side facing downwards. 7 • Using two screws and the 2.5 mm hex key, attach the filament spool holder at the back of the 3D printer. The "nose" on the end of the bracket points upward. 6 • Cut through the cable tie on both sides using the side cutters. 8 • First connect the mains cable to the • < ReadyPrint > appears on the touch power adaptor, then connect the power screen display. The 3D printer is now adaptor power cable to the 3D printer. ready for use. • Plug the mains plug on the power cable into the mains socket. Features • Max. size of the printed object 200 x 200 x 200 mm • Print various materials such as PLA, wood, elastic, copper; - additional ABS (with item no. 1592461) • Printed layer thickness 0.1 mm - 0.2 mm • Switch the 3D printer on. • Nozzle size 0.4 mm • Supports printing from SD card, PC and USB • "Cura" software included Print bed calibration 1 2 • Single extruder • Print speed 30 mm/s - 300 mm/s • Colour touch screen display • Tighten the 3 levelling screws under the print bed as far as they will go. • Place an A4 sheet of paper between the nozzle and the print bed to use as a measurement guide. 3 4 • In the < ReadyPrint > menu, first select • Repeat STEP 3 for the second, third, < Set > then < Levelling >. and fourth point (calibration sequence and motion direction of the nozzle are • Press < First > (first point). Nozzle shown). moves to the first point. • The distance between the nozzle and print bed is controlled by turning the first levelling screw. 5 • Slide the filament forward gently until the filament is slowly fed into the extruder. • Release the filament. 6 • If filament comes out of the nozzle, press < Stop >. • Remove the filament remnants with a pair of tweezers. Starting the printing process • The paper should be lightly clamped, so that you feel slight resistance when moving the paper. 1 2 Installing the filament 1 2 • In the < ReadyPrint > menu, first select • In the < 3D models > folder, select a < Print > then < PageDown >, several ready-to-print model, times if necessary, until the folder e.g. < RF100.gcode >. < 3D Models > is shown. • Open the < 3D Models > folder. • Mount the filament on the spool holder. • Insert the filament tube into the tube holder. 3 4 3 • Confirm printing with < OK >. • DONE. • Insert the filament into the tube until approximately 5 cm is visible at the extruder end. Filament feed 1 2 • In the < ReadyPrint > menu, select • In the < ReadyPrint > menu, first select < Move > and then press < Z+ > twice < Filament >, then < Preheat >. to increase the distance between the • Press < Add > several times until nozzle and the print bed. the target temperature of 220 °C is reached. 3 4 • In the < Filament > menu, wait until the • The LCD panel displays the status actual temperature (in this case 221 °C) notification < filament changing >. The has reached the target temperature. 3D printer is now ready for the filament feed-in. • Press < Load >. This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights reserved, including translation. Reproduction by any method, i.e. photocopy, microfilm, or in digital, electronic, optical or in any form, requires prior written approval from the publisher. Reproduction by printing, even in part, is also prohibited. This publication represents the technical status at the time of printing. Copyright 2017 by Conrad Electronic SE. *1592461_1592620_V1_1017_02_LS_qsg_EN
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US XMP Toolkit : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42 Instance ID : uuid:29aef230-6936-44de-8f70-4096303bfa68 Original Document ID : adobe:docid:indd:d9439d28-21fb-11df-a762-cc125a375cc9 Document ID : xmp.id:320b22cc-486f-9c40-b69a-227a22901e3a Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0d9044c7-e9ca-c547-9b0c-8c947a30cc7e Derived From Document ID : xmp.did:664ccdba-5f62-7d42-97eb-1573e47123c6 Derived From Original Document ID: adobe:docid:indd:d9439d28-21fb-11df-a762-cc125a375cc9 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Windows) History Changed : / History When : 2017:10:26 16:17:11+08:00 Create Date : 2017:10:26 16:17:11+08:00 Modify Date : 2017:10:26 16:17:21+08:00 Metadata Date : 2017:10:26 16:17:21+08:00 Creator Tool : Adobe InDesign CC 2017 (Windows) Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 4 Creator : Adobe InDesign CC 2017 (Windows)EXIF Metadata provided by EXIF.tools