01 30961A 1345 1HP 0130961

User Manual: 1345 - 1HP

Open the PDF directly: View PDF .
Page Count: 28

LOGIC CONTROL

C2 Wiring

FACTORY SET

See pages 15 & 16

for other wiring

configurations

Serial #

(located on electrical box cover)

Installation Date

Wiring Type

2 YEAR WARRANTY

PATENT PENDING

The Maintenance Alert System™

allows the installer to set an internal

Maintenance Cycle Counter. An LED

on the 3-button station will signal when

the set number of cycles is reached or

when the opener requires immediate

service.

NOT FOR RESIDENTIAL USE

OWNER’S MANUAL

MODEL T

LOGIC CONTROL (VER. 2.0)

INDUSTRIAL DUTY DOOR OPERATOR

TABLE OF CONTENTS

SPECIFICATIONS

Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Motor Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Safety Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Weights & Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

PREPARATION

Track Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Powerhead Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Trolley Carriage/ Chain Attachment . . . . . . . . . . . . . . . . . . . . . . .4

INSTALLATION INSTRUCTIONS

Mounting Header Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Mounting Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Operator Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Straight Arm Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

ENTRAPMENT PROTECTION ACCESSORIES

Sensing Edges & Photo Eyes . . . . . . . . . . . . . . . . . . . . . . . . . . .7

LIMIT SWITCH ADJUSTMENT

Limit Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

POWER & CONTROL WIRING

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Ground Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Control Station Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Optional Control Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Control Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .28

EMERGENCY DISCONNECT SYSTEM

Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

BRAKE ADJUSTMENT

Brake Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

CLUTCH ADJUSTMENT

Clutch Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Clutch Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

WIRING DIAGRAMS

1 PH Control Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3 PH Control Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

1 PH Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3 PH Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

STANDARD PROGRAMMING

Wiring Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 & 16

Self Monitoring Safety Devices . . . . . . . . . . . . . . . . . . . . . . . . .16

RPM Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Maximum Run Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Maintenance Alert System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

OPTIONAL PROGRAMMING

Mid Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Timer to Close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Red Green Warning Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Board Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

REPLACEMENT PARTS & MAINTENANCE

Trouble Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . .21 & 22

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Customer Service Contact Information . . . . . . . . . . . . . . . . . . .23

Electrical Box parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 & 25

Chassis Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 & 27

PACKING LIST

PART #

01-17278

02-103L

10-10203

10-10204

10-10205

11-10130

11-10197

19-41ML

40-15259

40-55

75-10174

QTY.

DESCRIPTION

OWNERS MANUAL

3 BUTTON STATION

DOOR CURVED ARM

DOOR BRACKET

TRACK END BRACKET

PIVOT SHAFT

TAKE-UP BOLT

MASTER LINK, #41

LABEL, MAINTENANCE ALERT

LABEL, TROLLEY CAUTION

FRONT IDLER ASSEMBLY

PART #

75-10214

75-10259

75-17942

82-HN38-12

82-HN38-16

82-RN31-26

84-FN-31

84-FN-38

84-LH-38

85-LS-38

86-CP045-108

QTY.

DESCRIPTION

DOOR ARM ASSEMBLY

TRACK SPACER ASSEMBLY

TROLLEY SLIDER

HEX BOLT, 3/8-16 X 3/4" LONG

HEX BOLT, 3/8-16 X 1" LONG

CARRIAGE BOLT, 5/16-18 X 2-1/2"

FLANGE NUT, 5/16-18

FLANGE NUT, 3/8-16

LOCKNUT, 3/8-16

LOCKWASHER, 3/8"

COTTERPIN, 9/64 X 1-1/2" LONG

HARDWARE KIT (K77-13821)

Before beginning your installation check that all components were supplied and received undamaged.

Before attempting to install, operate or maintain the operator, you must read and fully understand this

manual and follow all safety instructions.

These instructions are intended to highlight certain safety related issues. These instructions are not

intended to be comprehensive. Because each application is unique, it is the responsibility of the purchaser,

designer, installer and end user to ensure that the total door system is safe for its intended use.

MOTOR

TYPE: . . . . . . . . . . . . . . . . . .Continuous duty

HORSEPOWER: . . . . . . . . .1/3, 1/2, 3/4 & 1 HP

SPEED: . . . . . . . . . . . . . . . .1725 RPM

VOLTAGE: . . . . . . . . . . . . . .115, 208-230 Single phase

230, 380, 460, 575 Three

Phase

CURRENT: . . . . . . . . . . . . . .See motor nameplate

10-1/2"

Door Height Plus 4 feet (minimum)

*20-1/2"

13-1/8"

Highest Point of Door Travel

*For Units with Brake add 3-1/2"

(Standard on 3/4 & 1HP models Optional on 1/3 & 1/2HP)

MECHANICAL

DRIVE REDUCTION: . . . . . . .Primary: Heavy duty (5L)

V-Belt. Secondary: #41 chain/sprocket. Output: #48

chain (1/3 &1/2HP) or #41 chain (3/4 &1HP)

OUTPUT SHAFT SPEED: . . . .140 R.P.M.

DOOR SPEED: . . . . . . . . . . . .11" - 12" per sec.

depending on door

BRAKE: . . . . . . . . . . . . . . . . . .Solenoid actuated disc

brake on 3/4 & 1HP

BEARINGS: . . . . . . . . . . . . . . .Output Shaft: Shielded

Ball Bearing. Clutch Shaft: IronCopper sintered and oil

impregnated.

SAFETY

DISCONNECT: . . . . . . . . . . . . .Quick disconnect door

arm for emergency manual door operation.

SAFETY PHOTO EYES (Optional): Thru beam or retro

reflective devices used to provide non-contact safety

protection. Directly interface to Lift Master CPS-L or

CPS-LN4 Commercial Protector Systems.

SAFETY EDGE (Optional): . . . Electric or pneumatic

sensing device attached to the bottom edge of door.

A REVERSING DEVICE IS STRONGLY

RECOMMENDED FOR ALL COMMERCIAL

OPERATOR INSTALLATIONS. REQUIRED WHEN THE

3 BUTTON CONTROL STATION IS OUT OF SIGHT OF

DOOR OR ANY OTHER CONTROL (AUTOMATIC OR

MANUAL) IS USED.

SPECIFICATIONS

ELECTRICAL

TRANSFORMER: . . . . . .24VAC Secondary

CONTROL STATION: . . .NEMA 1 three button station.

OPEN/CLOSE/STOP W/ LED

WIRING TYPE: . . . . . . . .C2 (Factory Shipped)

Momentary contact to OPEN & STOP, constant pressure

to CLOSE, open override plus wiring for sensing device

to reverse. See pages 15 thru 19 for optional wiring

types and operating modes.

LIMIT ADJUST: . . . . . . . .Linear driven, fully adjustable

screw type cams. Adjustable to 24 feet.

WEIGHTS AND DIMENSIONS

HANGING WEIGHT: 80-110 LBS.

OPERATOR PREPARATION

Spacer Bracket

(mounted nylon pad side up)

Front Idler Assembly

Trolley Carriage

L - Slot

Master Link

Take-up Bolt

Roller Chain

Master Link

Hex

Nut

Straight Arm

Lockwasher

Hex Nut

Trolley Assembly

Take-up Bolt

Trolley Carriage

Reel chain

around idler and

over spacer brackets

POWERHEAD ATTACHMENT

1. Position the track assembly on the frame of the

powerhead so that the motor side of operator is in back

(away from door ).

2. Loosely install two 3/8"-16 x 3/4" bolts and nuts in third

hole from the end of the track .

3. Align the track so that the bolts inserted in step 2 line up

with the L-Slots in the frame.

4. Connect the track to the powerhead by fastening two

3/8"-16 x 3/4" bolts and nuts through the frame and the

end holes in track. Tighten all four bolts to secure the

track to the powerhead.

TROLLEY CARRIAGE / CHAIN ATTACHMENT

1. Attach the take-up bolt to the trolley carriage using

3/8-16" hex nuts and lock washer, as shown below.

2. Using one of the master links, attach the chain to the

other end of the trolley carriage. Reel the chain around

the front idler shaft, over the spacer brackets, back to

the drive shaft sprocket, and then to the take-up bolt on

the carriage.

3. Using the other master link, attach the chain to the

take-up bolt and tighten to the desired chain tension.

Chain Tension: With trolley positioned at either end of

the track, a properly adjusted chain will sag about 3" at the

mid-point. If necessary, remove links from the chain to

achieve proper adjustment.

KEEP DOOR BALANCED. STICKING OR BINDING DOORS

MUST BE REPAIRED. DOORS, DOOR SPRINGS, CABLES,

PULLEYS, BRACKETS AND THEIR HARDWARE MAY BE

UNDER EXTREME TENSION AND CAN CAUSE SERIOUS

PERSONAL INJURY OR DEATH. CALL A PROFESSIONAL

DOOR SERVICEMAN TO MOVE OR ADJUST DOOR SPRINGS

OR HARDWARE.

WARNING

CAUTION WARNING

WARNING

TRACK ASSEMBLY

1. Using the 3/8"-16 x 3/4" bolts and flange hex nuts

supplied, assemble the operator track by installing and

tightening the track spacer brackets. Position the

spacers evenly over the length of the track.

NOTE: The nylon pad on the spacer bracket should

face up.

2. Using (2) 3/8"-16 x 1" bolts and lock washers, install the

front idler assembly to the second set of holes of one

end of the track. Refer to the illustration below.

3. Slide the trolley carriage onto the track so that the

take-up bolt will be toward the operator.

Carpenter’s

Level

Header Wall

High Point

of Travel

Door Travel

Projection

IMPORTANT NOTE: Before the operator is installed, be sure the door has been properly aligned and is working

smoothly. Although each installation will vary due to particular building characteristics, refer to the following general

procedures to install the operator.

MOUNT HEADER BRACKET

The trolley operator is generally mounted over the center

of the door. However, off center mounting may be

required due to interfering structures or location of door

stile / top section support. In such cases, the operator

may be mounted up to 24" off center on torsion spring

doors. Extension springs require center mounting.

1. Locate the center of the door and mark a line on the

wall directly above the door. Extend this line up the

wall.

2. Determine the highest point of door travel. Slowly raise

the door and observe the action of the top section.

When the top section reaches its highest point, use a

level and project a line from this point to the center line

the of the door.

MOUNT OPERATOR

1. Allowing the motor to rest on the floor, raise the front

end of the track assembly to the front header bracket

and fasten using the 3/8" dia. x 6.40" long pivot shaft

and cotterpins supplied.

3. Using the projected lines for location, mount a suitable

wood block or length of angle iron to the wall above the

door opening. Refer to the illustration below. This will

provide a mounting pad for the front header bracket of

the operator. If necessary reinforce the wall with

suitable mounting brackets to ensure adequate support

of mounting pad. Using suitable hardware, mount the

(U-shaped) front header bracket to the pad.

Vertical Center Line of Door

3.50"

1.75"

4" MIN.

High Rise Point

Projection Line

Header Bracket Drill Pattern

2. Swing the operator to a horizontal position above the

guide rails and temporarily secure with a suitable rope,

chain, or support from the floor. Now open garage door

slowly, being careful not to dislodge the temporary

support. Using the door as a support, place a level

against the rail and shim the operator until it is

horizontal. Make sure that the operator is aligned with

the center line of the door.

Header Bracket

Pivot Shaft

Cotterpins

Using the door as support, shim

operator to a horizontal position.

Guide

Rails

Operator Alignment

INSTALLATION INSTRUCTIONS

Powerhead Support Brace

Mid-Span

Support Brace

Center Line of Door

Straight Arm

Door Bracket

Curved

Door Arm

Top

Roller

Pivot Bolt

INSTALLATION INSTRUCTIONS

OPERATOR SUPPORT

1. The illustration below shows a typical method of

hanging the operator from the ceiling. Each installation

may vary, but in all cases side braces should be used

for additional strength.

2. For mounting of the support brace(s) to the powerhead,

Four holes (clearance up to 3/8" bolts) are located on

each side of frame.

NOTE: If the operator is longer than 15 feet, use of a mid-

span support is recommended.

STRAIGHT ARM ATTACHMENT

1. Fully close the door and move the trolley slider to within

(2") two inches of the front idler.

2. Latch the straight door arm to the fixed roll pin in the

trolley carriage. Make sure the open side of notch on

the arm faces the doorway.

3. Attach the door bracket to the door arm using the

3/8"-16 x 1" bolt and nylon locking nut provided. Leave

the nut and bolt loose enough to allow the two pieces to

pivot freely.

4. Using 3/8" hardware provided, bolt the curved door arm

to the straight arm, aligning the mounting holes in such

a way that the door bracket pivot bolt will be in line with

the top rollers on the door.

5. Position the door bracket to the center line on the door.

Using suitable hardware, attach the door bracket to the

door. Many installations, except solid wood doors, will

require additional support for the door. Refer to the

illustration below.

IMPORTANT NOTE: At this time, ensure all bolts and lag

screws are properly secured.

FAILURE TO SUSPEND THE OPERATOR SECURELY MAY

RESULT IN SERIOUS PERSONAL INJURY OR DEATH,

AND/OR PROPERTY DAMAGE.

WARNING

CAUTION WARNING

WARNING

TO AVOID SERIOUS PERSONAL INJURY OR DEATH FROM

ELECTROCUTION, DISCONNECT ELECTRIC POWER BEFORE

MANUALLY MOVING LIMIT NUTS.

WARNING

CAUTION WARNING

WARNING

MAKE SURE THE LIMIT NUTS ARE POSITIONED BETWEEN THE LIMIT SWITCH ACTUATORS BEFORE

PROCEEDING WITH ADJUSTMENTS.

If other problems persist, call our toll-free number for

assistance: 1-800-528-2806.

1. To adjust limit nuts depress retaining plate to allow nut

to spin freely. After adjustment, release plate and

ensure it seats fully in slots of both nuts.

2. To increase door travel, spin nut away from actuator.

To decrease door travel, spin limit nut toward actuator.

3. Adjust open limit nut so that door will stop in open

position with the bottom of the door even with top of

door opening.

4. Repeat Steps 1 and 2 for close cycle. Adjust close limit

nut so that actuator is engaged as door fully seats at

the floor.

Retaining Plate

CLOSE Limit Switch

SAFETY

OPEN Limit Switch

Actuator

(Aux. Open) Limit Switch

PHOTO EYES & SENSING EDGES

Sensing devices supplied for door industry type operators

with an isolated normally open (N.O.) dry contact output

are compatible with your operator. This includes

pneumatic and electric edges, and through beam and retro

reflective photo eyes. If your door does not have bottom

safety photo eyes or a sensing edge and you wish to add

a safety device to your application, please contact your

local LiftMaster Authorized Dealer.

If not pre-installed by the door manufacturer, mount the

sensing edge on the door according to the instructions

provided with the edge. The sensing edge may be

electrically connected by either coiled cord or take-up reel.

Important Notes:

a. Proceed with Limit Switch Adjustments before making

any sensing edge wiring connections to operator as

described below.

b. Electrician must hardwire the junction box to the

operator electrical box in accordance with local codes.

ENTRAPMENT PROTECTION ACCESSORIES (OPTIONAL)

WIRING:

For wiring of your sensing device to the operator, refer to

the wiring diagrams supplied on pages 13 and 14. See

field connection terminals identified as Reversing Device.

TAKE-UP REEL: Take-up reel should be installed 12"

above the top of the door.

COIL CORD: Connect operator end of coil cord to

junction box (not supplied) fastened to the wall

approximately halfway up the door opening.

It is strongly recommended that a SAFETY PHOTO EYE OR

SENSING EDGE BE USED IN CONJUNCTION WITH THE

OPERATOR.

WARNING

CAUTION

WARNING

NOTICE

LIMIT SWITCH ADJUSTMENT

WARNING

CAUTION WARNING

WARNING

DISCONNECT POWER AT THE FUSE BOX BEFORE

PROCEEDING.

OPERATOR MUST BE PROPERLY GROUNDED AND

CONNECTED IN ACCORDANCE WITH LOCAL ELECTRICAL

CODES. NOTE: THE OPERATOR SHOULD BE ON A SEPARATE

FUSED LINE OF ADEQUATE CAPACITY.

ALL ELECTRICAL CONNECTIONS MUST BE MADE BY A

QUALIFIED ELECTRICIAN.

WARNING

CAUTION WARNING

WARNING

TO AVOID DAMAGE TO DOOR AND OPERATOR, MAKE ALL

DOOR LOCKS INOPERATIVE. SECURE LOCK(S) IN "OPEN"

POSITION.

IF THE DOOR LOCK NEEDS TO REMAIN FUNCTIONAL,

INSTALL AN INTERLOCK SWITCH.

Before installing power wiring or control stations be sure to follow all specifications and warnings described

below. Failure to do so may result in severe injury to persons and/or damage to operator.

The operator electrical box is only to be accessed by trained “LIFTMASTER” technicians. If service is

required contact your local LIFTMASTER dealer.

Do not install any wiring or attempt to run the operator without consulting the wiring diagram. Install the

optional Reversing Edge before proceeding with the Control Station installation.

Remove the cover from the electrical enclosure. Inside this enclosure you will find the wiring diagram(s) for

your unit. Refer to the diagram (glued on the inside of the cover) for all connections described below. If this

diagram is missing, call the number on the back of this manual. DO NOT INSTALL ANYWIRING OR

ATTEMPT TO RUN THIS OPERATOR WITHOUT CONSULTING THE WIRING DIAGRAM.

IMPORTANT SAFETY NOTES

INSTALL POWER WIRING & CONTROL STATION

WARNING

CAUTION WARNING

WARNING

ANY MAINTENANCE TO THE OPERATOR OR IN THE AREA

NEAR THE OPERATOR MUST NOT BE PERFORMED UNTIL

DISCONNECTING THE ELECTRICAL POWER AND LOCKING-

OUT THE POWER VIA, THE MAIN DISCONNECT SWITCH.

UPON COMPLETION OF MAINTENANCE THE AREA MUST BE

CLEARED AND SECURED, AT THAT TIME THE UNIT MAY BE

RETURNED TO SERVICE.

WARNING

CAUTION WARNING

WARNING

INSTALL THE CONTROL STATION IN LINE OF SIGHT WITH

THE DOOR, BUT AWAY FROM THE DOOR AND ITS

HARDWARE. IF CONTROL STATION CANNOT BE INSTALLED

WHERE DOOR IS VISIBLE, OR IF ANY DEVICE OTHER THAN

THE CONTROL STATION IS USED TO ACTIVATE THE DOOR, A

REVERSING DEVICE MUST BE INSTALLED ON THE BOTTOM

OF THE DOOR. FAILURE TO INSTALL A REVERSING DEVICE

UNDER THESE CIRCUMSTANCES MAY RESULT IN SERIOUS

INJURY OR DEATH.

POWER WIRING CONNECTIONS

1. Connect power wires coming from the main to the

captive terminal block in the electrical box enclosure

marked with the label shown below.

2. Be sure to run all power wires through the conduit hole

in the electrical box enclosure marked with the label

shown below.

CONTROL WIRING CONNECTIONS

1. Connect control wires to the TB1 terminal block located

on the Printed Circuit Board (shown below).

1 SBC

4 CMN

5 STOP

6 CLOSE

7 OPEN

8 REV

9 IR

10 DIAG

11 CMN

12 24AC+

13 24AC-

ON THREE PHASE MACHINES ONLY:

Incorrect phasing of the power supply will cause the motor

to rotate in the wrong direction.

OR IN THE AREA NEAR THE OPERATOR MUST

NOT BE PERFORMED UNTIL DISCONNECTING

THE ELECTRICAL POWER AND LOCKING-OUT

THE POWER VIA, THE MAIN DISCONNECT

SWITCH. UPON COMPLETION OF

MAINTENANCE THE AREA MUST BE CLEARED

AND SECURED, AT THAT TIME THE UNIT MAY

BE RETURNED TO SERVICE.

4 Feet

Approximate

Control

Station

Optional

Controls

Maintenance Alert

System™

If light is Flashing

it is time for routine

Door and Opener

Maintenance.

If light is Steady On,

call for immediate

service.

Service every

_______ cycles.

1. Mount Control Stations no further than (12") from each

other.

2. Mount Control Stations (12") from the door enclosure.

3. Mount WARNING NOTICE beside or below the Control

Station.

4. Mount MAINTENANCE ALERT label to either side of

control station.

1. Connect earth ground to the chassis ground screw in

the electrical box enclosure marked with the label

shown below.

2. Use same conduit entry into the electrical box as the

power wiring.

IMPORTANT: THIS UNIT MUST BE PROPERLY

GROUNDED. FAILURE TO PROPERLY GROUND THIS

UNIT COULD RESULT IN ELECTRIC SHOCK AND

SERIOUS INJURY.

40-10033B

INSTALL POWER WIRING & CONTROL STATION (CONT’D)

1 SBC SINGLE BUTTON CONTROL

2INTERLOCK

3INTERLOCK

4CMNCOMMON

5 STOP STOP

6 CLOSE CLOSE

7 OPENOPEN

8REVREVERSE

9IR INFRARED PHOTO EYES

10 MAS MAINTENANCE ALERT SYSTEM

11 CMNCOMMON

12 24AC+ 24 VOLT AC

13 24AC- 24 VOLT AC

On all models with B2 control wiring, a terminal bracket

marked R1 R2 R3 is located on the outside of the

electrical enclosure. Any commercial type LiftMaster

brand receiver may be mounted to this bracket. The

operator will then open a fully closed door, close a fully

open door, stop an opening door, and reverse a closing

door from the radio transmitter. In TS control wiring the

operator will only open the door or reset the timer to close.

However, for additional door control from a 3-button

transmitter, a commercial three-channel radio receiver

(with connections for OPEN/CLOSE/STOP) is

recommended.

2. Be sure to run all control wires through the conduit hole

in the electrical box enclosure marked with the label

shown below.

3. Apply power to the operator. Press OPEN push button

and observe direction of door travel and then Press the

STOP button.

If door did not move in the correct direction, check for

improper wiring at the control station or between operator

and control station.

MOUNTING INSTRUCTIONS

RADIO CONTROLS

GROUND WIRING

EMERGENCY DISCONNECT SYSTEM

Pull emergency

release handle

straight down.

Emergency disconnect

will open.

Emergency

Disconnect

Door Arm

TO DISCONNECT DOOR FROM OPENER

Door arm is released from trolley when emergency disconnect

opens.

To avoid being struck by door arm, do not stand under the

rope or door arm when pulling the emergency release.

WARNING

CAUTION WARNING

WARNING

Header

Bracket

Straight

Door Arm

Assembly

Emergency

Release

Handle

Door

Bracket

Door

Chain

Clevis

Trolley

Emergency

Disconnect

Track

Curved

Door Arm

NOEC

Lift free end of

door arm to trolley.

Pull emergency handle

to allow arm to engage

roll pin. Release handle.

Emergency disconnect

will close.

Emergency

Disconnect

Door Arm

TO RECONNECT DOOR ARM TO TROLLEY

BRAKE ADJUSTMENT

A solenoid brake is standard on 3/4 and 1 horsepower models, and is optional on 1/3 and 1/2 horsepower models. The

brake is adjusted at the factory and should not need additional adjustment for the the life of the friction pad.

Replace friction pads when necessary. Refer to the

illustration for identification of components for the solenoid

type brake system.

Friction Pads

Release Lever

Plate Assembly

Solenoid

Solenoid Brake System

CLUTCH ADJUSTMENT & AUXILIARY REVERSAL SYSTEM

1. Remove cotterpin from nut on the clutch shaft.

2. Back off clutch nut until there is very little tension on the

clutch spring.

3. Tighten clutch nut gradually until there is just enough

tension to permit the operator to move the door

smoothly but to allow the clutch to slip if the door is

obstructed. When the clutch is properly adjusted, it

should generally be possible to stop the door by hand

during travel.

4. Reinstall Cotterpin.

The Auxiliary Reversal System works in tandem with the

adjustable clutch to detect if a closing door meets an

obstruction. If an obstruction is met and causes the clutch

to slip, the Auxiliary Reversal System will return the door

to the full open position. The Auxiliary Reversal System is

designed to protect the door and motorized operator. It is

not intended as a replacement for a safety sensing device,

nor will it work for sectional doors when a jackshaft

operator is used.

Cotterpin

Adjusting Nut

Spring

Clutch Pulley

Clutch Plate

Clutch Pad

Washer

STANDARD POWER & CONTROL CONNECTION DIAGRAM

Logic Control Board (VER. 2.0) - 115V, 208, 230V, 1Ph

Logic Control Board (VER. 2.0) - 208, 230V, 380V, 460V, 3Ph

Logic Control Board (VER. 2.0) - 115V, 208, 230V, 1Ph

LOGIC CONTROL (VER. 2.0) 1 PHASE WIRING DIAGRAM 10120-1

NOTE:

CONTACTOR 1PH / 3 PH JUMPER

SHOULD BE IN 1 PH POSITION

NOTES:

1) SEE OWNER'S MANUAL FOR DIP SWITCH FUNCTIONS AND PROGRAMMING PROCEDURES.

2) TO REVERSE MOTOR DIRECTION

115 VOLTS: ALWAYS EXCHANGE PURPLE AND GREY ALL VOLTS & PHASES.

230 VOLTS: INTERCHANGE PURPLE (E10) & GREY (E15) WIRES AT LOGIC BOARD.

3) TRANSFORMER PRIMARY VOLTAGE SAME AS LINE VOLTAGE.

4) SINGLE PHASE UNITS ARE EQUIPPED WITH AN EXTERNAL LINE

BREAK DEVICE, AND MAY BE EQUIPPED WITH AN ADDITIONAL

INTERNAL PILOT DUTY THERMAL O/L DEVICE.

(SEE NOTE 3)

(SEE NOTE 2)

(SEE

NOTE 4)

(SEE NOTE 4)

INTERNAL MOTOR

WIRING

T1 - BLUE

T2 - WHITE

T3 - ORANGE

T4 - YELLOW

T5 - BLACK

T8 - RED

O/L- BROWN

(SEE NOTE 4)

(BL/BK)

LOGIC CONTROL (VER. 2.0) 3 PHASE WIRING DIAGRAM 10120-3

230 VOLT MOTOR CONNECTION

380/460 VOLT MOTOR CONNECTION

NOTES:

1) SEE OWNER'S MANUAL FOR DIP SWITCH FUNCTIONS AND PROGRAMMING PROCEDURES.

2) TO REVERSE MOTOR DIRECTION: INTERCHANGE ANY 2 OF THE 3 POWER WIRES AT L1, L2 & L3,

OR EXCHANGE PURPLE (E17) & GREY (E16) WIRES AT LOGIC BOARD.

3) TRANSFORMER PRIMARY VOLTAGE SAME AS LINE VOLTAGE.

4) THREE PHASE UNITS MAY BE EQUIPPED WITH AN INTERNAL PILOT DUTY

THERMAL OVERLOAD DEVICE, OR AN EXTERNAL LINE MONITORING DEVICE.

(SEE NOTE 3)

(SEE

NOTE 4)

208/

MOTOR O/L LEAD

COLOR BROWN

EXTERNAL

(BL/BK)

(SEE NOTE 4)

Refer to printed circuit board illustration on page 20 for all component locations.

Before Programming the logic board, set the operators open and close limits. LEDs on the logic board

are provided to assist setting the limits. As each limit is activated the corresponding LED will light up. The

abbreviations are Open Limit Switch (OLS), Close Limit Switch (CLS) and Sensing Limit Switch (SLS).

Refer to page 7 for limit switch adjustment instructions.

WIRING TYPE PROGRAM SETTINGS

Determine wiring mode:

There are many wiring modes available on the Logic Board. Read the descriptions of the different wiring types to

determine which setting will be correct for each application.

Set the dip switches to the desired wiring mode:

Adjust the 4 dip switches on the logic board to match the settings for the desired wiring type. The dip switches are

shown in the picture.

TYPE STATION

C2 3 Button, 3 Button Radio Control

Function: Momentary contact to open and stop with constant pressure to

close, open override plus wiring for sensing device to reverse.

Programmable mid stop available with this wiring type.

B2 3 Button, 1 Button, 1 & 3 Button Radio Control

Function: Momentary contact to open, close and stop, plus wiring for

sensing device to reverse and auxiliary devices to open and close

with open override. Programmable mid stop available with this

wiring type.

D1 2 Button, 3 Button Radio Control

Function: Constant pressure to open and close with wiring for sensing

device to stop.

E2 3 Button Radio Control

Function: Momentary contact to open with override and constant pressure

to close. Release of close button will cause door to reverse (roll-

back feature) plus wiring for sensing device to reverse.

TS 3 Button, 1 Button, 1 & 3 Button Radio Control

Function: Momentary contact to open, close, and stop with open override

and Timer To Close. Every device that causes door to open,

including a reversing device, activates the Timer To Close.

Auxiliary controls can be connected to open input to activate the

Timer To Close. If the timer has been activated, the open button

and radio control can recycle the timer. The stop button will

deactivate the Timer To Close until the next command input. The

Timer To Close will function from the programmable mid-stop with

this wiring type. (NOTE: Requires Optional self monitoring

photo eyes to operate.)

Logic Control Pushbuttons Open, Close, Stop

Open, Close and Stop buttons are mounted directly on the Logic Control board. This will provide easy

programming ability and door control at the electrical box. Either the stop control or a jumper must be wired between

terminals 4 and 5 for the on board push buttons to function.

1 2 3 4

OFF

1 2 3 4

OFF

1 2 3 4

OFF

1 2 3 4

OFF

1 2 3 4

OFF

WIRING TYPE PROGRAM SETTINGS CONT’D

To use the operator in any of the Failsafe wiring modes, or Timer To Close wiring modes (TS, T, FSTS), a LiftMaster self

monitoring safety device must be installed.

Recommended LiftMaster Self Monitoring Safety Devices:

CPS-L NEMA 1 Direct Connect Eyes

CPS-LN4 NEMA 4 Direct Connect Eyes

NOTE:

1. External interlocks may be used with all functional modes.

2. Auxiliary devices are any devices that have only dry contacts. Examples are: photocell, loop detector, pneumatic or

electrical treadles, radio controls, one button stations, pull cords, etc.

3. Open override means that the door may be reversed while closing by activating an opening device without the need

to use the stop button first.

SELF MONITORING SAFETY DEVICE OPTIONS

FSTS

1 2 3 4

OFF

FAIL

SAFE

1 2 3 4

OFF

FAIL

SAFE

1 2 3 4

OFF

FAIL

AFE

1 2 3 4

OFF

FAIL

SAFE

1 2 3 4

OFF

1 2 3 4

OFF

TYPE STATION

T3 Button, 1 Button, 1 & 3 Button Radio Control

Function: Momentary contact to open, close, and stop, with open override and

Timer To Close. Every device that causes the door to open, except a

reversing device, activates the Timer To Close. Auxiliary controls can

be connected to open input to activate the Timer To Close. If the Timer

To Close has been activated, the open button and radio control can

recycle the timer. The stop button will deactivate the timer until the next

command input. The Timer to Close will function from the

programmable mid-stop with this wiring type. (NOTE: Requires

Optional self monitoring photo eyes to operate.)

FSTS Momentary button contact for open, close and stop. Radio controls

allowing open, close and stop. User set midstop. User set Timer To

Close. The single button station opens the door to the full open limit

bypassing the mid stop and activates the Timer To Close, putting the

operator in TS mode until the door reaches the down limit, or is

stopped in travel. At which time the operator enters the B2 mode.

(NOTE: Requires Optional self monitoring photo eyes to operate.)

C2 Failsafe 3 Button, 3 Button RadioControl

Same functions as C2. Self Monitoring safety device must be installed

to operate door. See Self Monitoring Safety Device Options below.

B2 Failsafe 3 Button, 1 Button, 1 & 3 Button Radio Control

Same functions as B2. Self Monitoring safety device must be installed

to operate door. See Self Monitoring Safety Device Options below.

D1 Failsafe 2 Button, 3 Button Radio Control

Same functions as D1. Self Monitoring safety device must be installed

to operate door. See Self Monitoring Safety Device Options below.

E2 Failsafe 2 Button, 3 Button Radio Control

Same functions as E2. Self Monitoring safety device must be installed

to operate door. See Self Monitoring Safety Device Options below.

Maximum Run Timer (Setting is Recommended)

Feature: The door will run in one direction for a set amount of time. Default time

is 90 seconds. Installer can adjust the 90 second timer to the open

cycle plus 10 seconds.

Benefit: Should the door hit an obstruction that is not detected by a sensor, it

will stop after the programmed amount of time and not continue to drive

into the obstruction. This may help prevent prolonged human

entrapment as well as help prevent damage to the door and operator .

To Program:

1. Start with the door closed and the limits set.

2. Set the dip switches to "set Max Run Timer".

3. Press Open and wait for the door to reach the full open limit.

4. Return the dip switches to the desired wiring type (C2, B2, etc.) and Close the

door. The Maximum Run Timer is now set and will allow the door to move in one

direction no more than 10 seconds longer than it normally takes to travel from

close to open.

Example: If it takes the door 13 seconds to open normally, the operator will stop

running after 23 seconds. If the Max Run Timer is not programmed, it will run for

90 seconds total in either direction.

Note: For very large, slow moving doors, where the normal travel time is close to

90 seconds setting the MRT is essential to move the door the full travel distance.

STANDARD PROGRAMMING FEATURES

RPM Sensor/Auxiliary Reversal System (Programming is Recommended)

Feature: By programming the RPM sensor to a specific application, the logic

board learns the speed the door travels with reference to the spinning

motor. This sensor activates the start winding and recognizes clutch

slippage.

Benefit: By removing the centrifugal start switch from 1/3 and 1/2 horsepower

single-phase motors the leading cause of motor failure is eliminated.

The auxiliary reversing benefits of the RPM sensor are designed to

prevent excessive door and operator damage upon hitting a solid

obstruction. LiftMaster recommends the use of safety devices for

primary safety protection.

To Program:

1. The open and close limits must be set before setting the RPM sensor.

2. Start with the door closed and turn all dip-switches to the off position.

3. Press open then press and hold the “learn” button on the Logic board until the

door reaches the full open position. You should see the Learn LED turn off

after pressing the learn button; it will turn back on about 5 seconds later. If the

LED did not cycle, start over and wait about 1/4 to 1/2 second between

pressing

“

open” and “learn.”

4. Return the dip switches to your regular wiring type (C2, B2, etc.) and close the

door.

Note: LiftMaster 2.0 Logic operators are designed to work in most cases without

adjusting the RPM sensor. It is still recommended to set this feature on every

installation. This feature will need to be reset if the motor or logic board is ever

replaced.

SET

MAX RUN

TIMER

1 2 3 4

OFF

STANDARD PROGRAMMING FEATURES CONT’D

MAS (Maintenance Alert System)

Feature: An internal cycle counter will activate a flashing LED on the

three-button control station when the preset number of cycles is

reached. Setting this feature is optional. By default, this feature will

never activate.

Benefit: The consumer will be aware of when it is time for a scheduled

maintenance on the door or operator.

To Program:

1. Close the door.

2. Set the dip switches to “set Maintenance Alert System”

3. Press “close” to zero out the counter.

4. Press “open” for every 5,000 cycles the operator should wait before

flashing the LED.

5. Return the dip switches to your regular wiring type (C2, B2, etc.) and close

the door.

EXAMPLE: The door is being installed with 30 thousand cycle springs. To set

the MAS for 30,000 cycles press close, then open 6 times. Return the dip

switches to the desired wiring type.

Special Notes about the MAS: A 5th wire must be run to the control station to

activate the MAS LED. When the operator is serviced after the MAS has started

the LED flashing, repeat the setup procedure for the next service visit. To see

how many cycles the operator has been through set the dip switches to “set

MAS” and watch the MAS led. It will flash once for every 1000 cycles the

operator has been used then pause and repeat. Every time the operator leaves

the close limit is counted as one cycle.

OPTIONAL PROGRAMMING FEATURES

Open

Stop

Adds 5,000 cycles to

Maintenance Alert

System Activation

Counter.

Clears memory, sets

Maintenance Alert

System Activation

Counter to 0 cycles.

Adds 10,000 cycles

to Maintenance Alert

System Activation

Timer.

Press This To Get This

Mid Stop

Feature: Door will open to an installer set height that is less than fully open.

Benefit: The door will not open fully which will reduce unwanted airflow

through the doorway. The door will not cycle fully providing longer

door and operator life.

To Program:

1. Close the door.

2. Set dip switches to “set mid stop.”

3. Press open (the door will begin moving)

4. Press stop when the desired mid stop height is reached.

5. Return the dip switches to the desired wiring type (C2,B2,etc.). The door will

now stop at this height every time the door is opened.

Notes: A momentary open command will open the door fully from the mid stop

position. Photo eyes and other safety devices will not further open the door from

the mid stop position. Timer To Close will work from the mid stop position.

Maintenance

Alert LED

MAINTENANCE

ALERT

SYSTEM

1 2 3 4

OFF

SET

MIDSTOP

1 2 3 4

OFF

OPTIONAL PROGRAMMING FEATURES CONT’D

Adjusting your red/green warning lights

Feature: The logic board can adjust the amount of time that a warning light will flash before the Timer To Close will

activate the door to close.

Benefit: Advanced warning of door closure helps prevent traffic collisions with the door.

To Program:

1. Set the dip switches to “Set Timer To Close”

2. Press stop for every additional 5 seconds of

pre-movement warning.

3. Return the dip switches to the desired wiring type.

Requirements: Must have the Logic 2 red green warning light kit #001A4730 and must have at least one of the

following safety devices attached: CPS-L, CPS-LN4, CPSII, CPSII-N4. When running, the dip switches must be set for

TS, T, or FSTS. See red/green warning light instructions for further details.

Timer To Close

Feature: Installer can set a timer to automatically close after a preset amount

of time once all safety devices are unobstructed.

Benefits: Door will automatically close after being used. Extremely convenient

where users may not be concerned with closing the door. For

example Apartment Buildings and Fire Stations.

Requirements: Must have at least one of the following safety devices

attached: CPS-L, CPS-LN4, CPSII, CPSII-N4. When running, the dip switches

must be set for TS, T, or FSTS

To Program:

1. Close the door.

2. Set dip switches to “Set Timer To Close”

3. Press “close” to zero out the timer.

4. Press “open” for every 5 seconds seconds the operator should wait before

attempting to close the door.

Example: The door is supposed to close 30 seconds after the user drives

through. To set the TTC for 30 seconds press close, then open 6 times.

5. Return the dip switches to the desired wiring type. TS, T, or FSTS

Notes: For longer delay time settings, use the Single Button Control (terminal

1) to add 1 minute at a time. To deactivate the timer press stop. The timer will

be reactivated on the next operation command.

Reminders: FSTS wiring mode allows the Timer To Close to be activated by

the Single Button Control (terminal 1) only. T wiring mode allows the door to

attempt to close only one time for safety purposes.

Open

Stop

Single Button

Control

Adds 5 seconds to

countdown timer.

Resets the timer to

close to 0 seconds.

Turns off electronic

search for photo eyes

after photo eyes have

been intentionally

removed.

Adds 5 seconds to

“Red warning light

before closing” time.

Adds 60 seconds to

countdown timer.

Press This To Get This

SET

TIMER

TO CLOSE

1 2 3 4

OFF

LOGIC 2.0 PCB BOARD ILLUSTRATION

Control Wiring

Terminal Block

(see pages 8-9)

RPM Learn

Button

Dip Switch

Open, Close, Stop Buttons

(see page 16)

(see pages 8-9)

Power Wiring

Terminal Block

(see pages 8-9)

TROUBLE SHOOTING

Clearing The Memory 3 - steps

STEP 1: To reset most of the user installed settings back to factory defaults:

1. Turn all the dip switches ON.

2. Press and hold the Learn button about 5 seconds.

3. The Learn LED will turn off while you hold the button down and turn back on

about 5 seconds later.

4. Return the dip switches to the desired wiring type.

Note: A. The Max Run Timer is now set to 90 seconds

B. The Timer To Close is now set to 0 seconds

C. The Mid Stop is now deactivated

D. The Maintenance Alert System is now deactivated

Note: To clear the Mid Stop only Set/Program the Mid Stop at the open limit.

The logic board understands this to mean that no mid stop is desired.

Each open command will open

the door about a foot and a half

then stop, after reaching the open

limit each close command will

close the door about a foot and a

half then reverses back to full

open.

RPM sensor is not adjusted

correctly.

Reset the RPM sensor. Also

verify that the software is

version 260 or better.

Order replacement chips from

Parts and Service.

The door will open some but not

completely. And the door will

close some and not completely.

Extra commands are able to get

the door to move completely

The Maximum run timer is not

set correctly.

Reset the Maximum Run Timer

The door will open some but not

completely. An extra open

command is able to get the door

to open completely

There may be a Mid Stop set. Reset the mid-stop by

programming it to be at the open

limit.

The door will open but will only

close after a 5 second delay with

constant pressure on the close

button.

a) The Photo Eyes, edge or

other sensing device is

obstructed or activated.

b) The Logic board thinks that

the direct connect photo eyes

are attached and blocked

a) Remove the obstruction,

check the safety device wires

Use the LEDs to help check

correct wiring (see

Diagnostic procedure) Verify

that the board is accepting

commands by using the

onboard control station.

for continuity and shorts.

b) Unlearn the photo eyes

from the memory (see clear

memory section). Also

verify that the Logic Board

Chip is Version 260 or

better. Order replacement

Chips from Parts and Service.

The operator will not respond to

any commands

a) Operator control station is

wired wrong

b) Motor is malfunctioning

b) Verify voltage getting to the

motor.

SYMPTOM PROBABLE CAUSE RESOLUTION

TROUBLESHOOTING GUIDE

TROUBLE SHOOTING

Diagnostic Checklist Procedure

1. Look for the 3 Green LEDs

A. If the 24Vac light is out, check the transformer and any interlock switches, then replace either the transformer or

the logic board.

B. If the 5 VDC light is out, and the 24Vac is lit, replace the board.

C. If the Stop Button light is out, check the wiring to the control station, if the site does not require a stop button use

a jumper across terminals 4 and 5. If the LED is still not lit call for more assistance.

2. Check your control station:

A. Place the operator into diagnostic mode (all DIP switches ON)

B. Watch the LEDs as each control button is pressed. The LEDs should light with each Open, Close, and Single

Button Control command. The Stop should turn off the LED.

3. Activate the limit switches to verify functionality. Also watch the LEDs during door travel to check for over active limit

switches.

4. Disconnect all devices and reattach them one at a time testing for failure after each item is replaced. This will

determine which device is causing the failure. For further assistance call for technical support.

24Vac Green Indicates that 24 VAC is being received from the transformer

5VDC Green Indicates that 5VDC is being generated for the logic board to use

Diag Red Indicates that the MAS LED on the 3 button control station is being turned on.

REV Red Indicates a short between common and terminal 8. Pressing the edge should turn ON this LED

Open Red Indicates a short between common and terminal 7. Pressing the open button should turn ON this LED

Close Red Indicates a short between common and terminal 6. Pressing the close button should turn ON this LED

Stop Green Indicates a short between Common and terminal 5. Pressing the stop button should turn OFF this LED.

SBC Red Indicates a short between Common and terminal 1. Pressing the Single Button

Control station should turn ON this LED.

OLS Red Indicates the Open Limit Switch being pressed

CLS Red Indicates the Close Limit Switch being pressed

SLS Red Indicates the Sensing Limit Switch being pressed

Learn Amber This LED is normally on and in Diagnostic mode (all dip switches on) this LED

will flash to indicate the chip is OK.

LED COLOR MEANING OF EACH LED

ORDER

STEP 2: To “unlearn” the photo eyes.

The latest software automatically learns if direct connect photo eyes (CPS-L or CPS-LN4) are attached during the first

open cycle of operation. If they are disconnected at some point after this, they must be unlearned.

1. Set the dip switches to set Timer To Close.

2. Press Open 2 times then Close 2 times and then Stop 2 times (order is not specific).

3. Return the dip switches to the desired wiring type.

STEP 3: Relearn RPM.

Because factory default is set without a door attached to the operator, factory default setting is not a preferred status.

1. Start with the door closed and set all Dip switches to the off position.

2. Press open then press and hold the “learn” button on the Logic board (see picture) until the door reaches the full

open position. You should see the Learn LED turn off after pressing the learn button; it will turn back on about 5

seconds later. If the LED did not cycle, start over and wait about 1/4 to 1/2 second between pressing “open” and

“learn.”

3. Return the dip switches to your regular wiring mode and close the door.

Diagnostic LED

There should always be 3 green LEDs activated (24Vac, 5 VDC, and STOP Button). Check for this first then proceed to

check the status of the remaining LEDs

Use SAE 30 Oil (Never use grease or silicone spray).

Repeat ALL procedures.

Do not lubricate motor. Motor bearings are rated for continuous operation.

Do not lubricate clutch or V-belt.

Inspect and service whenever a malfunction is observed or suspected.

CAUTION: BEFORE SERVICING, ALWAYS DISCONNECT OPERATOR FROM POWER SUPPLY.

For use with Maintenance Alert System.

Check at the intervals listed in the following chart.

MAINTENANCE SCHEDULE

ITEM

Drive Chain

Sprockets

Clutch

Belt

Fasteners

Manual Disconnect

Bearings & Shafts

PROCEDURE

Check for excessive slack.

Check & adjust as required.

Lubricate

Check set screw tightness

Check & adjust as required

Check condition & tension

Check & tighten as required

Check & Operate

Check for wear & Lubricate

EVERY 3 MONTHS

5,000 CYCLES



EVERY 6 MONTHS

10,000 CYCLES



EVERY 12 MONTHS

20,000 CYCLES



HOW TO ORDER REPAIR PARTS

OUR LARGE SERVICE ORGANIZATION

SPANS AMERICA

INSTALLATION AND SERVICE INFORMATION

IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK.

SIMPLY DIAL OUR TOLL FREE NUMBER:

1-800-528-2806

HOURS: (Central Standard Time)

6:00 A.M. TO 7:00 P.M. - Monday through Friday

8:00 A.M. TO 4:30 P.M. - Saturday

www.liftmaster.com

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION:

• PART NUMBER

• PART NAME

• MODEL NUMBER

ADDRESS ORDERS TO:

THE CHAMBERLAIN GROUP, INC.

Technical Support Group

6020 S. Country Club Road

Tucson, Arizona 85706

ILLUSTRATED PARTS - ELECTRICAL BOX

Qty

Item

P/N

10-10013

10-12553

10-12806

18-10036

23-10041

31-12542

82-PX04-20

82-PX06-16

84-LH-06

Description

Depress Plate

Nut Plate, Switch

Backup Plate

Spring, Depress Plate

Limit Switch

Standoff, Limit Switch

Screw, #4-40 x Pan Head Phillips

Screw, #6-32 x 1" Pan Head Phillips

Locknut, #6-32 Nylon Hex

Below are replacement kits available for your operator. For replacement of electrical box, motor or brake components be sure

to match model number of your unit to kit number below to ensure proper voltage requirements. Optional modifications and/or

accessories included with your operator may add or remove certain components from these lists. Please consult a parts and

service representative regarding availability of individual components of kits specified below. Refer to page 23 for all repair part

ordering information.

Electrical Box Replacement Kits

To order a complete electrical box kit, add a K- prefix to the

model number of your operator. For example:

T5011L (Operator) = K-T5011L (Electrical box replacement kit)

Electrical Box Sub-Assemblies

K72-13912 Limit Shaft Assembly

K72-12514 Limit Switch Assembly

Motor Kits

K20-1033B2L Models T3311L, T3321L

K20-3033B4 Models T3323L, T3338L, T3343L

K20-51033B Model T3325L

K20-1050B2L Models T5011L, T5021L

K20-3050B4 Models T5023L, T5038L, T5023L

K20-51050B Model T5025L

K20-1075B2 Models T7511L, T7521L

K20-3075B4 Models T7523L, T7538L, T7543L

K20-51075B Model T7525L

K20-1100B2T Models T1011L, T1021L

K20-3100B4T Models T1023L, T1043L

Shaft Assemblies

K72-12506 Clutch Shaft Assembly (1/3 & 1/2 HP Models)

K72-12507 Clutch Shaft Assembly (3/4 & 1 HP Models)

K72-12508 Output Shaft Assembly (1/3 & 1/2 HP Models)

K72-12509 Output Shaft Assembly (3/4 & 1 HP Models)

Hardware, Track, Drive Chain Kits

K77-13821 Hardware Kit

See pg. 19 Drive Chain

See pg. 19 Track

Brake Kits

71-B120 115 Volt Models

71-B240 230-460 Volt Models

Notes: Single phase units are equipped with an external line

break device and may be equipped with an additional internal

pilot duty thermal O/L device.

Three phase units may be equipped with an internal pilot duty

thermal O/L device or an external line break device.

K72-13912 LIMIT SHAFT ASSEMBLY KIT

Item

Description

Limit Shaft, Standard T

Flange Bearing, 3/8" I.D.

Limit Nut

Sprocket 48B9 x 3/8" Bore

Washer, Shim 3/8" I.D. x .050 THK.

Washer, Shim 3/8" I.D. x .010 THK.

Roll Pin, 1/8 DIA. x 1 Long

E Ring, 3/8"

Rotating Cup

Qty

K75-12514 LIMIT SWITCH ASSEMBLY KIT

P/N

11-10021

12-10028

13-10024

15-48B9A

80-10025

80-10026

86-RP05-108

87-E-038

29-10344

* COMPLETE ELECTRICAL BOX KITS

Item

Description

Electrical Box

Electrical Box Cover

(See Variable Components)

PCB assembly

Terminal Block, Radio

Standoff, Assembly

RPM Sensor Board

Housing, RPM Board

Programmed Chip

Qty

P/N

10-13790

10-10115

21-XXXX

25-XXXX

79-13433

42-10040

75-13705

79-15016

093D0148

29-CDO-XXX

* Electrical Box Kits include parts from K72-13912 and K72-12514

ITEM

PART NO.

21-14182

21-5460

25-2006

25-2008

25-2010

25-2015

25-2020

25-10296

25-13840

DESCRIPTION

Transformer, 115 Volts

Transformer, 460 Volts

Overload, 6 Amp

Overload, 8 Amp

Overload 10 Amp

Overload 15 Amp

Overload 20 Amp

Overload 2.8-4.4 Amp

Overload 2.0-3.0 Amp

VARIABLE COMPONENT KITS

T3311L

T3321L

T3323L

T3343L

T3325L

T3338L

T5011L

T5021L

T5023L

T5043L

T5025L

T5038L

T7511L

T7521L

T7523L

T7543L

T7525L

T7538L

T1011L

T1021L

T1023L

T1043L

REPAIR PARTS KITS – ELECTRICAL BOX LOGIC CONTROL (VER. 2.0)

DRIVE CHAIN

TRACK

H2 O1

O2 O11

O10

C16

C10

C13

C14

C15

10-10011M1

C10

B13 B11

B15 B9

27-10188

MOTOR (SEE PG. 17)

C11

C7 C4

O4 O8

C12

B12

B10

B15

B14

B16

10-10030

ELECTRICAL BOX

(SEE PG. 17))

17-6014 Brake Components

Standard on 3/4 & 1HP units; Optional on 1/3 & 1/2HP units

ILLUSTRATED PARTS - MODEL T

Refer to the parts lists below for replacement kits available for your operator. If optional modifications and/or accessories

are included with your operator, certain components may be added or removed from these lists. Individual components of

each kit may not be available. Please consult a parts and service representative regarding availability of individual

components. Refer to page 23 for all repair part ordering information.

CLUTCH SHAFT ASSEMBLY KITS

K72-12507 (1/3 &1/2 HP) OR K72-12506 (3/4 & 1 HP)

ITEM PART # DESCRIPTION QTY

C10

C11

C12

C13

C14

C15

C16

Clutch Plate

Clutch Shaft

Bearing 3/4" I.D.

Sprocket, 48B10 x 3/4"

Cogged Belt

4L Motor Pulley 7" O.D.

Spring, Clutch (1/3 & 1/2 HP)

Spring, Clutch (3/4 & 1 HP)

Clutch Disc

Shim Washer Thick

Shim Washer Thin

Nut 3/4-16 Castle

Flatwasher 3/4" I.D.

Cotterpin 1/8" x 1-3/4" Long

Roll Pin 1/4" x 1-1/8" Long

Roll Pin 1/4" x 2" Long

Turac 3/4" Push on Fastener

OUTPUT SHAFT ASSEMBLY KIT

K72-12508 (1/3 &1/2 HP) OR K72-12509 (3/4 & 1 HP)

ITEM PART # DESCRIPTION QTY

O10

O11

Output Shaft

Bearing, Flange

Sprocket, 41B10 x 3/4" Bore, PM

Sprocket, 48B10 x 3/4" Bore, Steel

Sprocket, 41B32 x 3/4" Bore

Sprocket, 48B10 x 3/4" Bore, PM

Drive Chain, #41 x 47 Pitches

Limit Chain, #48 x 33 Pitches

Shim Washer, Thin

Roll Pin, 1/4" Dia. x 1-1/8" Long

Roll Pin, 1/4" Dia. x 1-1/2" Long

Push Ring, 3/4" I.D.

11-10015

12-10331

15-41B10G1

15-48B10GXX

15-41B32GXX

15-48B10G1

19-41047M

19-48033

80-10023

86-RP08-102

86-RP08-108

87-P-075

10-10166

11-10014

12-10029

15-41B10G1

16-5L300

17-10165

18-10164

18-10168

39-10167

80-10022

80-10023

84-SH-76

85-FW-75

86-CP05-108

86-RP08-102

86-RP08-200

87-P-075

BRAKE ASSEMBLY KITS

ITEM PART # DESCRIPTION QTY

B10

B11

B12

B13

B14

B15

B16

Brake Hub

Brake Solenoid Cover

Brake Release Lever

Brake Disc, Zinc Plated

Spring Cup for Brake Assembly

Brake Stud

Spring, Compression x .875" Long

Chain, #48 x 1 Pitch

Brake Solenoid, 115V

Brake Solenoid, 230-460V

Spacer, .20 I.D. x .31 Long

Brake Mounting Plate Assembly

Brake Pressure Plate Assembly

Feather Key

Screw, #10-32 x 1/2" Serrated Flange

Cotter Pin, 1/8" x 1-3/4" Zinc Plate

Push on Fastener, 5/8" Int. Star

07-10179

10-10187

10-10190

10-10191

11-16094

11-16095

18-10194

19-48001

22-120

22-240

31-10186

75-10180

75-10184

80-9001

82-WX10-08T

86-CP04-108

87-P-062

KIT PART # FOR OPERATOR(S)

71-B120 115 Volt Models

71-B240 230-460 Volt Models

K77-13821 HARDWARE KIT

ITEM PART # DESCRIPTION QTY

Curved Arm

Door Bracket

Header Bracket

Header Pivot Pin

Slider Assembly

Front Idler Assembly

Straight Arm Assembly

Track Spacer Assembly

10-10203

10-10204

10-10205

11-10130

75-10170

75-10174

75-10214

75-10259

Doors to 8'

Doors to 10'

Doors to 12'

Doors to 14'

Doors to 16'

Doors to 18'

Doors to 20'

Doors to 22'

Doors to 24'

10-5808

10-5810

10-5812

10-5814

10-5816

10-5818

10-5820

10-5824

PART #

Track, 11' Length

Track, 13' Length

Track, 15' Length

Track, 17' Length

Track, 19' Length

Track, 21' Length

Track, 23' Length

Track, 27'-6" Length

19-5112

19-5114

19-5116

19-5118

19-5120

19-5124

19-5810

19-5812

19-5814

19-5816

19-5818

19-5820

19-5824

DOOR TRACK AND DRIVE CHAIN KITS

#41 CHAIN (3/4 & 1 HP)

#48 CHAIN (1/3 & 1/2 HP)

DOOR TRACK DOOR DRIVE CHAIN

DOOR HEIGHT

K75-12870 STRAIGHT AND CURVED ARM ASSY

Curved Armbly

Straight Arm Assembly

10-10203

75-10214

DESCRIPTION

REPAIR PARTS KITS – MODEL T LOGIC CONTROL (VER. 2.0)

01-30961A

OPEN / CLOSE

3 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN TO CENTER AND STOP BUTTON

2 OR MORE KEY LOCKOUT

R1 R2 R3

7 6 4 5

Stop

Open

Stop

Open

7 6 4 5

Stop

Open

2 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN TO CENTER

STANDARD

7 6 4

Open

D1 & E2

MODE ONLY

2 OR MORE

7 6 4

Open

D1 & E2

MODE ONLY

OPEN / CLOSE

B2, T, TS & FSTS

MODE ONLY

Any Commercial Type

LiftMaster Brand Receiver

1 BUTTON STATION OR ANY AUXILIARY DEVICE RADIO CONTROLS

SENSING DEVICE TO REVERSE OR STOP EXTERNAL INTERLOCK

11 82323

Remove Factory Installed Jumper

When Interlock is Used

ONE 2 OR MORE

STANDARD

7 6 4 5

Stop

Open

IMPORTANT NOTES:

The 3-Button Control Station provided must be connected for operation.

If a STOP button is not used, a jumper must be placed between terminals 4 and 5.

All Wiring Types

Keyswitch

Sensing Device

Maintenance

Alert LED

10 10

Maintenance

Alert LED

Maintenance

Alert LED

(RED)

(WHITE)

(RED)

(WHITE)

(RED)

(WHITE)

Note: 11 & 4 are both the same common

Either is acceptable

See Note

CONTROL CONNECTION DIAGRAM

01 30961A 1345 1HP 0130961

Navigation menu

Versions of this User Manual:

Views

Navigation