OPERATING INSTRUCTIONS Software_Voltcraft_LCR_4080_LCR_HANDMESS Ver. 01 121064 An En Software Voltcraft LCR 4080 HANDMESS
User Manual: Software_Voltcraft_LCR_4080_LCR_HANDMESS - Ver. 01 Component er digital VOLTCRAFT LCR 4080 Calibrated to: Manufacturer's standards (no certificate) CAT I Display (cou from Conrad.com
Open the PDF directly: View PDF .
Page Count: 3
Download | |
Open PDF In Browser | View PDF |
Install PC software & USB driver For WINDOWS VISTA_XP _2000 and USB Driver’s Installation 1. Put the disk in the disk drive. Following dialogue box will appear automatically. Please execute the “autorun.exe” if it does not appear. 1. StartÆControl PanelÆPerformance and Maintenance. 1. Connect meter to PC with USB cable. Following dialogue box will appear automatically. Please select “Install USB [for WINDOWS_VISTA_ XP_2000“to install. • INSTALL USB driver (for WINDOWS_ VISTA _XP_2000): Please refer to the METER and USB DRIVER’S • WINDOWS_VISTA_XP_2000: Install pc software for WINDOWS VISTA XP 2000 • Instruction Manual: Operation instruction manual. • EXIT: Exit install program. 2. Button explanations • WINDOWS7_VISTA: install pc software for WINDOWS7 with VISTA. Directory setting for VISTA. Following window will comes up automatically, when click the button “WINDOWS7_VISTA_XP_2000”. SET CONNECTION PORT 2. Select “System”. 2. Installation. 3. Select “Hardware” ÆDevice Manager. 4. In this window, you see the number of the port selected by system auto manically. You can change it. Please write down the port number, it will be needed for manual connection. SOFTWARE OPERATION Com-Port Setup The user can setup the Com-Port parameter in this form. Initial Setup On the Virtual Meter Main Form please click the Menu Bar->File->Initial Setup. Value Set There are symmetrical, dissymmetrical, and direct inputs Hi/Lo Limits. The Go/No Go will be the basis of the three modes. Instrument Set On the Virtual Meter Main Form please click the Menu Bar->File->Initial Setup-->Instrument Set. The user also can set the LCR Meter parameter (L/C/R, Q/D/R, Frequency, Parallel/Serial, Auto/Menu), then click “Set Instrument” button to set parameter into the LCR Meter. Uninstallation of USB Driver 1. StartÆSettingÆControl PanelÆAdd or Remove ProgramsÆChange/Remove. The Virtual Meter Software When everything is done, the Virtual Meter software will work. The form displays the values that appear on the LCR Meter. Then the user can use all the function that the Virtual Meter provided from the Menu Bar. 2. Select “FTDI USB Serial Converter Drivers”ÆChange/Remove. 3. Click “Yes”. Range On the Virtual Meter Main Form please click the Menu Bar->File->Initial Setup-->Range. This form shows the current range and the group number (1~10) that the user can change. The Auto/Manual selection can calculate automatically or be changed by hand. When the left side value bigger than the right side value, the Wrong Range will light. While the Wrong Range lights, user should adjust the value or there will be an error. Profile To click the Menu Bar->Open->Profile, and the Profile form will display as below. The function is to display the item values including current value, maximum (Max), minimum (Min), average (Avg), total number (Total), and Reject Rate. List Frequency Distribution In the Virtual Meter Main Form, to click the Menu Bar->Open->Profile-->List, and the List Form will display as below. The table displays the real-time data. To click ”record” button, then the table will be added one data including No., Item (L/C/R), Value, Unit, Range, Q.C., Item (Q/D/R), and Value. In the Main Form, to click the Menu Bar->Open->Profile->Frequency Distribution. And the Frequency Distribution will display. The vertical axle means number. The horizontal axle means distribution points. Sorting List (Save Data) user can input information and save them into the report file. Please click the Menu Bar->File->Sorting, and the Sorting form will display as below. This form displays the current value, difference, total number, and standard value. If the user zooms in or zooms out the Sorting Form, the font and the object size will be changed.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 7.0 (Windows) Company : CHY Source Modified : D:20100422013052 Creator Tool : Acrobat PDFMaker 7.0 for Word Modify Date : 2011:06:14 08:15:57+02:00 Create Date : 2010:04:22 09:31:38+08:00 Metadata Date : 2011:06:14 08:15:57+02:00 Document ID : uuid:287e0c77-b178-4644-a6c2-a0c4176d6abf Instance ID : uuid:d3f06927-e326-4be3-9039-4440337f76c1 Version ID : 32 Format : application/pdf Title : OPERATING INSTRUCTIONS Creator : wm14 Subject : Headline : Page Count : 3 Page Layout : OneColumn Author : wm14EXIF Metadata provided by EXIF.tools